PEERLESS WSP 716 User manual

ISSUED: 11-14-06 SHEET #: 024-9010-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
1 of 4
B
Assembly Instructions - External Wall Plate
IMPORTANT! Read entire instruction sheet
before you start installation and assembly. MAXIMUM LOAD CAPACITY:
200 lb (91 kg)
Models: WSP 716, WSP 716-S,
WSP 716-W, WSP 724, WSP 724-S,
WSP 724-W
WSP 716, WSP 716S, and WSP 716W for studs on 16" (406
mm) centers, contains four cable management ports.
WSP 724, WSP 724S, and WSP 724W for studs on 16", 20"
and 24" (406 mm, 508 mm, 610 mm) centers, contains four
cable management ports.
A
Cable Management Ports
C
D
E
THIS
ENDUP
*Note: The mounting hole which
is closest to the lip of the plate
indicates the up position.
*
Note: Wall plate may
appear slightly different
than illustrated.
• Wall or mounting structure must be capable of sup-
porting a minimum static load of 600 lb (272 kg).
WARNING
9
9
9
9
9
9
9
9
9
9
PARTS LIST
WSP 724 WSP 716
PART # QTY. DESCRIPTION
A024-1043 1 wall plate 16" centers
024-1042 wall plate 24" centers
B510-9108 10 1/4-20 x 1/2" phillips screw
C520-9521 12 1/4-20 x 2 1/2" phillips screw
D560-9708 12 toggler
E540-1063 22 washer
MODEL #
9
9
9
9
9
9
9
9
9
9
PARTS LIST
WSP 724S WSP 716S
PART # QTY. DESCRIPTION
A024-4043 1 wall plate 16" centers
024-4042 wall plate 24" centers
B520-9511 10 1/4-20 x 1/2" phillips screw
C520-9522 12 1/4-20 x 2 1/2" phillips screw
D560-9708 12 toggler
E540-2056 22 washer
MODEL #
9
9
9
9
9
9
9
9
9
9
PARTS LIST
WSP 724W WSP 716W
PART # QTY. DESCRIPTION
A024-2043 1 wall plate 16" centers
024-2042 wall plate 24" centers
B520-9511 10 1/4-20 x 1/2" phillips screw
C520-9522 12 1/4-20 x 2 1/2" phillips screw
D560-9708 12 toggler
E540-2056 22 washer
MODEL #
WSP724 WSP716
THIS
ENDUP

ISSUED: 11-14-06 SHEET #: 024-9010-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
2 of 4
Wall plate (A) can be mounted to three studs that are 16" apart on center for WSP 716 models and 16",
20" or 24" on center for WSP 724 models. Use a stud finder to locate the edges of the studs. Use of an
edge-to-edgestudfinderishighlyrecommended.
Based on their edges, draw a vertical line down each stud’s center. Place wall plate on wall as a
template. Level plate, and mark the center of the twelve mounting holes. Make sure that the mounting
holes are on the stud centerlines. Drill twelve 1/2" holes through drywall and metal studs. Note: It may be
necessary to drill 5/32" pilot holes prior to drilling 1/2" holes.
• Product must be mounted through drywall that has a
minimum thickness of 1/2" and into metal studs, 26
gaugeorheavier.
• Make sure that togglers are anchored into the center
of the studs as shown in figure 1. The use of an "edge
toedge"studfinder is highly recommended.
WARNING
A
figure 1

ISSUED: 11-14-06 SHEET #: 024-9010-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
3 of 4
Drill 1/2" (13mm) dia. holes through drywall and studs at locations corresponding to wall plate. Insert togglers (D)
asshownbelow...
©2005PeerlessIndustries,Inc. Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
Rotatetoggler(D)
clockwise to wedge it
against inside walls
of metal stud.
Push into hole.
Pivotendoftoggler(D).
Slide plastic cap
forwardwhilepulling
back firmly on ring.
Break off excess.
Align wall plate
with hole in wall
andfastenusing
1/4-20screw(C).
wall plate
C
drywall
metal stud

ISSUED: 11-14-06 SHEET #: 024-9010-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
4 of 4
∅ 1/2"
(13 mm)
AA
WSP 716 WSP 724
Fasten wall plate to wall using twelve 1/4-20 x 2 1/2" phillips screws (C) and twelve washers (E) as shown below.
See below for proper holes to attach mount to wall plate. Attach wall mount to wall plate (A) using 1/4-20 x
1/2" screws (B) and washers (E)asindicatedbelow.
*
*
*
*
*
***
*
*
*
*
PLA 50 =
PLA 60, PLAV 60, PLAV 70 =
WSP 724 WSP 716
*