PEERLESS Slimline OP-LWB 530 Guide

ISSUED: 05-23-05 SHEET #: 029-9011-2 12-14-05

Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.

1 of 6

Installation andAssembly - Slimline®Wall Mount Model: OP-LWB 530, OP-LWB 530T

D

E

GA

C

B

K

J

I

F

IMPORTANT! Read entire instruction sheet before

you start installation and assembly.

Parts List

Some parts may appear slightly different than illustrated.

PART # QTY. DESCRIPTION

A2141-376 1 wall arm

B120-0015-1 1 lower tray (LWB 530 only)

120-0002 1 lower tray (LWB 530T only)

C1436-373 1 upper tray (LWB 530 & 350T only)

D510-9107 4 1/4" philips machine screw

E500-9006 4 #10 philips particle board screw

F540-9400 4 small flat washer

PART # QTY. DESCRIPTION

G3022-502 1 lock plug

H0000-322 1 key (not shown)

I520-9250 4 M5 x .8 x 10 mm philips screw

J2245-081 4 uni-clip

K520-1236 10 1/4" x 4" lag bolt

L540-9401 10 1/4 x 3/4 x 1/16 washer

• Installer must verify that the wall will safely support

thecombinedweightof all attached equipment and

hardware.

WARNING

L

MAXIMUM OSHPD LOAD

CAPACITY: 96 lb (43.5 kg)

os

pd

ISSUED: 05-23-05 SHEET #: 029-9011-2 12-14-05

Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.

2 of 6

For Wood Stud Walls add wood blocking as required

to accomodate wall arm hole pattern. Use wall arm

(A) as a template to drill ten 5/32" (4 mm) dia. holes

to a minimum depth of 4" (102 mm) into stud center

and blocking. Attach wall arm using ten

1/4" x 4" lag bolts (K) and 10 washers (L).

Skip to step 4.

Skip to pg. 3 if attaching to a concrete wall or

pg. 4 if attaching to concrete block.

Note:If you are installing to a metal stud wall,

pleaserefer to the accompanyingmetal stud

instruction sheet.

B

Make sure that swivel race tab on lower tray (B) is positioned as shown.

• Tighten wood screws so that wall plate is firmly

attached,butdonotovertighten.Overtighteningcan

damagethescrews,greatly reducing their holding

power.

• Never tighten in excess of 80 in • lb (9 N.M.).

• Make sure that mounting screws are anchored into the

center of the studs and wood blocking. The use of an

"edgeto edge" stud finder is highlyrecommended.

WARNING

BLOCKING

(BYENGINEEROFRECORD)

2XOR3XSTUDS

K

L

A

ISSUED: 05-23-05 SHEET #: 029-9011-2 12-14-05

Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.

3 of 6























































































































































































A

Fig. 3.1.1

Fig. 3.1.2

CONCRETE

Fig. 3.1.3

CONCRETE

WASHER

For Concrete Walls Order OP-ACC 204.

Making sure that it is level, use wall arm (A) as a template to

mark holes. Use an ANSI drill bit size between 0.255" - 0.259"

to drill eight holes to a minimum depth of 3.25" (83 mm) as

shown in figure 3.1.1. Blow the hole clean of dust and other

material.

Attach using washers and bolts as shown in figure 3.1.2

WARNING

• Concrete must be 3000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the wall will safely support four times the combined load of the equipment and all attached hard-

ware and components. Direct pull test to 800 lbs. or torque to 10 ft-lbs to test strength of concrete.

• Concreteanchorsare not intended for attachment to

concretewallcovered with a layer of plaster,drywall,

orotherfinishingmaterial.

WARNING

• Tighten concrete anchor bolts firmly, but do not

overtighten.Overtighteningcandamagethe bolts,

greatlyreducingtheirholdingpower.

• Never tighten in excess of 80 in • lb (9 N.M.).

WARNING

POWERSWEDGE BOLT

(560-1165)

WASHER

(540-9401)

A

USEHOLES SHOWN

BELOW

ISSUED: 05-23-05 SHEET #: 029-9011-2 12-14-05

Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.

4 of 6

WARNING

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

surface in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifica-

tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill

toavoidbreaking out the back of theholewhen entering a void or cavity.

• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and

components.

• Tightenscrewsfirmly,butdonotovertighten.Over-

tighteningcandamage the bolts, greatly reducing

theirholdingpower.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Distancebetweenends of threaded rod and locknuts

after tightening must be 1/8" minimum..

WARNING

THREADEDROD

(580-1143)

WASHER

(540-1061)

LOCKNUT

(530-1030)

For Concrete Block Walls Order OP-ACC 307.

Making sure that it is level, use wall arm (A) as a

template to mark holes. Drill eight .281" holes

through block as shown in figure 3.2.1. Blow the

holeclean of dust andother material.

Attach using washers, threaded rods, and lock

nuts as shown in figure 3.2.2.

WASHER









































































CONCRETE

BLOCK

A









































































CONCRETE

BLOCK

WASHER

(540-1061)

Fig. 3.2.1

Fig. 3.2.2

Fig. 3.2.3









































































CONCRETE

BLOCK

A

USEHOLES SHOWN

BELOW 1/8"

min.

ISSUED: 05-23-05 SHEET #: 029-9011-2 12-14-05

Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.

5 of 6

Attach lower tray (B) to wall arm (A) using four 1/4-20 x 3/8 philips screws (D). Tighten securely.

If the holes in the race on bottom of tray are not aligned, use a screwdriver and hammer to gently

tap the race so that the holes are visible.

Note: The race on the tray bottom is extremely difficult to swivel without the weight of the TV on

the tray.

Turn TV upside down on flat stable surface. Using four sets of screws (E)and washers (F) (for attachment to

mounting bosses if present), or uni-clips (J) and M5 screws (I) (see instruction card in fastener pack), or a

combination of both attach upper tray (C) to TV bottom. Attach at four places as close to the four corners of

the TV bottom as possible.

B

D

A

CE

J

I

F

ISSUED: 05-23-05 SHEET #: 029-9011-2 12-14-05

Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.

6 of 6

G

CB

G

C

Insert key into lock plug (G). Attach TV/upper

tray (C) to lower tray (B) as shown.

Slide upper tray (C) back until fully

engaged. Firmly hold in position while

you insert and tighten lock plug (G),

severalturns,untilfullyengaged.

Note: To remove key, slot must be in the

horizontalposition.Thismayrequirethat

you back off 1/4 turn.

PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.

Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.

• Always use an assistant or mechanical lifting equipment to safely lift and position the television.

WARNING

PEERLESS Slimline OP-LWB 530 Guide

Popular Rack & Stand manuals by other brands