PEERLESS Solid-Point PLCM 2 Guide

ISSUED:02-14-03 SHEET #: 201-9019-7 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
1 of 5
Read instruction sheet before you start installation and assembly.
Model:PLCM 2
Maximum Load Capacity:
225 lb (102.3 kg)
Installation and Assembly -Solid•Point™Flat Panel
Straight Column Mount
TABLE OF CONTENTS
Installations
InstallingPLCM2to ceiling.........................page 3
Applications
Installation of plasma screens and
30" or larger LCD screens.......................... page 4
Installation of small LCD screens............... page 5
• Installer must verify that the wall will safely support the
combinedweightofallattachedequipmentand
hardware.
WARNING

ISSUED:02-14-03 SHEET #: 201-9019-7 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
2 of 5
Description Qty Part #
Aceiling arm box 1 201-1062
Btilt bracket 1 200-1552
Dretaining collar 1 1800-375
EM5 x .8 x 10mm penta-pin™screw 4 505-9010
F2.875 OD x 2.125 ID x .062 H fiber washer 1 540-9432
GM10 x 1.5 x 15 mm penta-pin screw 8 520-9263
HM10 x 2" penta-pin tool 1 520-9260
IM5 x 1" penta-pin tool 1 520-9249
JM5 x .8 x 8 mm phillips Type F screw 4 520-1167
Before you begin, make sure all parts shown are included with your product.
PARTS LIST
D
F
A
B
Note: Some parts may not appear exactly as illustrated.
HI
E
G
J
Fasteners

ISSUED:02-14-03 SHEET #: 201-9019-7 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
3 of 5
ceiling plate (not included)
Threadsupportpipe(notincluded)intothreadedfittinginceilingplate(notincluded).Tighten-fourorfivecomplete
turns - leaving slot aligned with one small hole in the side of the ceiling plate threaded fitting. Insert and tighten one
M5 x .8 x 10 mm penta-pin screw provided with ceiling plate as shown. Use the M5 penta-pin tool (I) to tighten
screw. BY HAND, insert four M10 x 1.5 x 15 mm penta-pin screws (G) into threaded holes in the sides of ceiling
armbox(A).Leave approximately1/4" ofexposed thread.Slideceilingarmbox(A)andfiberwasher(F)ontoend
ofsupportpipe.Threadretainingcollar(D)ontothreadedendofsupportpipe. Tighten-fourorfivecompleteturns.
Slide ceiling arm box (A) down so that it is on top of retaining collar (D). Insert and tighten one M5 x .8 x 10 mm
penta-pinscrew(E) intoretaining collar(D)as shown. Insertone M5penta-pinscrew (E)through thetabon the
back of ceiling arm box (A). Use M5 penta-pin tool (I) to tighten screw just enough to stabilize support pipe.
Note: ADJ or EXT extension columns can be used in combination with, or in place of support pipe to achieve
differentlengths.
E
D
A
F
D
G
1/4"
G
E
M5 screw
BACKOF CEILING
ARMBOX
support pipe (not included)

ISSUED:02-14-03 SHEET #: 201-9019-7 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
4 of 5
Hang tilt bracket (B) onto ceiling arm box (A).
Adjust tilt as desired and tighten four M10 x 1.5 x
15 mm penta-pin screws (G) securely using M10
penta-pintool (H).
B
A
G
Attach tilt bracket (B) to adapter plate using four M10 x 15 mm penta-pin screws (G) in accordance with appropri-
atedrawingbelow.Tighten usingM10 penta-pintool(H).
G
B
Note: Refertoadapter plateinstruction sheetforattachment ofadapter platetoplasma before proceedingwith step2.
LANDSCAPE
LANDSCAPE PORTRAIT
LANDSCAPE PORTRAIT
B
A
G
B
G
ADAPTERPLATE
ADAPTERPLATE
PLASMASCREEN
PLASMASCREEN
Note:Screen andadapter
platemay appeardifferent
thanillustrated.
• For a safe assembly be sure to fully tighten four
screws(G).
WARNING

ISSUED:02-14-03 SHEET #: 201-9019-7 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
5 of 5
ADAPTERBRACKET
B
J
Attach tilt bracket (B) to adapter bracket using four M5 x 8 mm phillips screws (J).
Note: Do not use M5 x 6 mm screws that are included with the adapter bracket.
Note: Refertoadapterbracketinstruction sheetfor attachmentof adapterbrackettoLCDscreen beforeproceeding with
step 2.
Hang tilt bracket (B) onto ceiling arm box (A).Adjust tilt as desired and tighten four
M10 x 1.5 x 15 mm penta-pin screws (G) securely using M10 penta-pin tool (H).
B
A
G
©2004Peerless Industries,Inc. All rightsreserved.
Peerlessis aregistered trademarkof PeerlessIndustries,Inc.
Solid•Pointis atrademarkofPeerlessIndustries, Inc.
Allother brand andproduct namesare trademarksorregistered trademarksof theirrespective owners.
Note:Screen andadapter
platemay appeardifferent
thanillustrated.
LCDSCREEN
• For a safe assembly be sure to fully tighten four
screws(G).
WARNING