PEERLESS HL4UN-002 Guide

1 of 2 ISSUED: 06-03-11 SHEET #:120-9110-1
Insert two 1/4-20 x 1-3/4" carriage bolts (A)
into bottom of display base as shown in detail 1.
Model: HL4UN-002, HL4UN-002-Q10
Installation and Assembly:
Lock Down Hardware for Display Base Stands
1
BOTTOM OF BASE
FRONT
2
FRONT
A B
CD
A
DETAIL 1
MEASURE
DISTANCE
Measure distance between center lines of cut outs in
bottom of display base. Use measurement to mark
location of holes at point 1 and point 2, on table.
Drill two holes using a 9/32'' drill bit.
POINT 1
POINT 2
• drill
• 9/32" drill bit
• 5/8" open box wrench
E F G
HTOOLS NEEDED
HL4UN-002 HL4UN-002-Q10
Description Qty. Part # Qty. Part #
A
1/4-20 x 1 3/4" carriage bolt 2 520-1017 20 520-1017
BM4 x 16 mm phillips trilobe screw 2 520-2621 20 520-2621
CM4 x 16 mm socket pin screw 2 520-1087 20 520-1087
D1/4-20 sloped nut 3 530-0035 23 530-0035
EM4 x 12 mm socket pin screw 2520-1079 20 520-1079
F#8 flat washer 2540-1001 20 540-1001
Gplastic cap 2590-1294 20 590-1294
H4 mm allen wrench 1 560-9646 3 560-9646
Parts List
NOTE: Display and base may appear
different than illustrated

2 of 2 ISSUED: 06-03-11 SHEET #:120-9110-1
Hand tighten slope nut (D) through 1/4-20 x 1-3/4" carriage bolt (A) until snug against bottom of desktop surface.
Thread another slope nut (D) upside-down, about two turns from rst slope nut (D). Insert an open box wrench
between both slope nuts (D) and tighten. NOTE: Avoid jamming both slope nuts (D) together, doing so may make
it difcult to remove slope nut used for tightening rst slope nut (D) as shown in gure 3.1. After slope nut is secure
remove bottom slope nut as shown in gure 3.2. Repeat with remaining 1/4-20 x 1 3/4" carriage bolt (A).
Fasten two plastic caps (G).
TIGHTENING
SLOPE NUT
BOTTOM OF DESKTOP
FIGURE 3.1 FIGURE 3.2
A
3
NOTE: Do not overtighten slope nut (D)
plate may distort
FRONT
D
A
D
Thread two M4 x 16 phillips pan trilobe screws (B) to bottom display attachment holes as shown in g. 4.1.
Remove the two M4 x 16 phillips pan trilobe screws (B) and attach display screen to display base using two M4 x
16 mm socket pin screws (I) or M4 x 12 mm socket pin screws (E) with #8 at washers (F), as shown in gure 4.2.
Tighten with 4 mm security allen wrench (H). Use TV supplied screws for remaining holes.
4
g 4.1 g 4.2
B
DISPLAY SCREEN DISPLAY SCREEN
DISPLAY BASE
NOTE: Display and base may appear
different than illustrated
NOTE: Screws are installed using bottom
two display mounting locations.
Installation of Security Screws for Base/Screen Assembly
G
C or E
F
• If screws don’t get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
© 2011, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.