Penguin Edge MVME3100 User manual

1 Box contents
Make sure you receive all items of your shipment:
• MVME3100 board
• One printed copy of Quick Start Guide (this document)
• One printed copy of Safety Notes Summary
When installing or servicing the system or accessories,
strictly observe the safety precautions in the Safety Notes
Summary. Ignoring these instructions can void the system
warranty and cause personal injury or property damage.
2 ESD
Electrostatic discharge and incorrect installation or
removal of the card can damage circuit or shorten its life.
Use a properly grounded ESD wrist strap or work in an
ESD-safe environment.
Connect to the ESD connector at the front or the rear of
the system.
3 Site preparation
1. Make sure that all environmental and power requirements
defined in the Penguin Edge™ MVME3100 Installation and
Use manual are met.
2. Remove all items from the box.
4 Configure hardware
To produce the desired configuration and ensure proper operation of
the Penguin Edge™ MVME3100, you may need to carry out certain
hardware modifications before installing the module. For more
information, refer to the Penguin Edge™ MVME3100 Installation
and Use manual.
5 Install the board
Note: Before removing the housing cover make sure that the
system is shut down and disconnected from AC power.
1. Attach an ESD strap to your wrist.
2. Attach the other end of the ESD strap to an electrical ground.
The ESD strap must be secured to your wrist and to ground
throughout the procedure.
3. Remove any filler panel that might fill the slot.
4. Install the top and bottom edge of the MVME3100 into the guides
of the chassis.
5. Make sure the levers of the two injector/ejectors are in the
outward position.
6. Slide the MVME3100 into the chassis until you feel resistance.
7. Simultaneously move the injector/ejector levers in an inward
direction.
8. Verify that the MVME3100 is properly seated.
9. Secure the board to the chassis using the two screws located
adjacent to the injector/ejector levers.
10.Connect the appropriate cables to theMVME3100.
11. When the MVME3100 is installed in the chassis you are ready to
connect peripherals.
6 Connect peripherals
The following table lists the available connectors on MVME3100.
7 Complete installation
1. Verify that the board is installed and the power/peripheral
cables connected are appropriate for your system
configuration.
2. Replace the chassis or system cover, reconnect the system to
the AC or DC power source and apply power.
Penguin Edge™
MVME3100
Quick Start Guide
P/N: 6806800M29D JUNE 2022
Connector Function
J4 PMC expansion connector
J11, J12, J13, J14 PCI mezzanine card (PMC) slot 1 connector
J21, J22, J23 PCI mezzanine card (PMC) slot 2 connector
J24 Boundary scan header
J25 COP header
J27 USB connector
J28 Front panel SATA connector
J29 Planar SATA connector
J30 Planar SATA power connector
J41B 10/100/1000Mb/s Ethernet connector
J41A COM port connector
P1, P2 VME backplane connectors
J1A, J1B, J1C,
J1D
COM port connectors
J2A 10/100/1000Mb/s Ethernet connector
J2B 10/100Mb/s Ethernet connector
J10 PIM power/ground
J14 PIM I/O
P2 VME backplane connector

Penguin Edge™ MVME3100 Quick Start Guide
Penguin Solutions™, 2900 S. Diablo Way, Suite 190, Tempe, Arizona 85282
For technical assistance or to report product damage or shortages,
contact your local Penguin Solutions™ sales representative or visit
https://www.penguinsolutions.com/edge/support/.
Technical Assistance
For more information on this product, see the
Penguin Edge™ MVME3100 Single Board
Computer Installation and Use manual and other
related technical documentation, which can be found
by using the Documentation Search at
https://www.penguinsolutions.com/edge/support/.
Get More Information
Penguin Solutions is a trade name used by SMART Embedded Computing, Inc., a
wholly owned subsidiary of SMART Global Holdings, Inc. Penguin Edge is a
trademark owned by Penguin Computing, Inc., a wholly owned subsidiary of
SMART Global Holdings, Inc. All other logos, trade names, and trademarks are
the property of their respective owners. These materials are provided as a service
to our customers and may be used for informational purposes only. For full legal
terms and conditions, please visit www.penguinsolutions.com/edge/legal/.
©2022 SMART Embedded Computing, Inc.