Penguin P Series Maintenance and service guide

 Models:
P1/15
 P1/6
 P1/4
 P1/2
 P1/2HP
 P3/4
 P3/4HP
 P1
 P11/2
 P2
 P3
 P5
 P71/2
 Materials:
ACPVC
 BPolypropylene
 CPVDF
PenguinPumpsaredesignedtohandlealarge range of
chemicalswithoutdifficulty.Completelyconstructed of CPVC,
polypropylene, or PVDF, where in contact with the solutionbeing
pumped,SeriesPpumpshaveanupperworkingtemperatureof180/150/280degrees,
respectively,andthuscanhandlemostcorrosive,slurries,andabrasivesolutions.
SeriesPpumpsareeasytoinstallandoperate,andarevirtuallymaintenancefree.
Allpumpshavebeentestedforproperoperationbeforeleavingthefactory.Toobtain
optimumservicelife,pleasefollowallinstallationandoperationinstructions.
Introduction
Installation&Maintenance
SeriesP
SeriesP
P201M_i

Installthepumpascloseaspossibletothereservoirfromwhichtheliquidisbeingpumped.Asmoreenergyisnecessarytoprime
theliquidthantodischargetheuid,makethesuctionasshortaspossible.
ELECTRICAL
Models P1/15 and P1/6 pumps are supplied only in a single
phase, single voltage, 115V or 230V, 50/60c motor.All other
modelssuppliedwithasinglephasearedualvoltage,110/220V
or115/230Vmotors.Thefactorywiresalldualvoltagemotorsfor
thelowervoltage(110/115V)unlessotherwiserequested.When
changingfrom110/115Vwiringto220/230Vwiring,followthemotor
manufacturer’swiringinstructions,whicharefoundinthemotor
junctionbox.Besuretowirethemotorforcounterclockwiserotation
asviewedfromthesuctionentranceofthepump.Apowercord
andplugaresuppliedforimmediatepluginoperationonmotors
wiredforthelowervoltage.Thesemotorshavealreadybeenwired
atthefactoryforproperrotation.Aplugisnotsuppliedonmotors
wired 220/230V. Epoxied motor housings are not available on
eithervoltagemotoroftheP1/15orP1/6pumps.Allothermotor
housingsareepoxiedstandard.
Ifasuctionlineorsuctionextensionisrequired,enlargethesuc
tionline/extensionbyonesizelargerthanthesuctionentrance.
Neverreduceplumbingonthesuction.Avoid90degreeelbows
andneverusea180degreeelbow.Makesureeverysuctioncou
pling/connectionisairtight.Thebottomofthesuctionextension
shouldalwaysbeatleast2pipediametersabovethebottomofthe
tank.Ineitheroodedsuctionornonoodedsuction,theuseofa
checkvalveonthedischargeofthepumpisrecommended.Inthe
caseofanonoodedsuction,aappercheckvalveontheendof
PLUMBING
Thecorrectliquidlevelisveryimportant.Aliquidlevelwhichistoo
highcouldcausemotordamage.
LIQUIDLEVEL
Underoodedconditions,openallthevalvesinthesuctionand
dischargelines.Waitafewminutestoletentrappedairout.Close
allvalvesonthedischargeline.Leavesuctionvalveswideopen.
Aclosedsuctionvalvecouldcausedamagetotheimpellerand
theshaft.Startthepumpandcrackdischargevalvesopentolet
outanyadditionalentrappedair.Thenopenvalvetodesiredow.
PRIMING
Alwaysmakesurethereisenoughliquidinthereservoirandthe
levelishighenough,consideringthecapacityofthepumpunit.
Inadequateliquidwillcausevortexinthereservoir.Avortexoccurs
whenairmixesfromthesurfaceintotheuid,whichcandisturb
theowandalsopreventsthepumpfrompriming.Incaseswhere
thepumpisinstalledoutsidethereservoir,donotrunagainsta
closeddischargevalveformorethan5minutes.Thiswillcause
RECOMMENDATIONS
Anon/offswitchisoptionalonlyonModelsP1/4–P11/2single
phase.Motorssuppliedinthreephasearedualvoltage,230/460V,
50/60c,whicharenotwiredatthefactory.Sincedirectionofrota
tioncannotbedeterminedwithoutoperatingthepump,thepump
headandsnapringmustberemovedpriortobumpstarting.
Itisimperativethatthemotorrotationbecheckedbeforeopera
tion.Attach leads to motor and bump start a maximum of only
acouplesecondsasifyouwereturningalightswitchon/offas
fastaspossible.Donotleavemotorrunning.Asviewedfromthe
suctionentranceofthe pump,checkforcounterclockwise rota
tion.Ifclockwiserotation,changeanytwoleadsandagaincheck
rotation.ReplaceheadandsnapringasdescribedinAssembly.
ManyoptionsareavailableonthePSeriesmotorsincludingsingle
phase50c,explosionproof,largerhorsepowersto71/2,and575V
motors.Ifanyoftheseoptionsarerequired,pleasecheckthemo
thesubmergedsuctionlinemustbeinstalled.Tofacilitatepriming
thepump,installaTconnectionwithasmallvalvebetweenpump
caseandcheckvalve.Itisadvisabletouseadischargevalveafter
thecheckvalve.Allplumbingandaccessoriesmustbesupported
otherthanbythepump,inordertopreventpossibledistortionof
thepumpcase.Theuseofsomehoseinthedischargeplumbing
closetothedischargenozzleofthepumpwillabsorbanymove
mentofthesolidplumbingifvibrationsexists.
CHECKTHELIQUIDLEVEL.Thecorrectliquidlevelishalfwaybe
tweenthebungholeandthecenterlineofthedischargenozzle.
Undernonoodedconditions,llupthepumpslowlyfromtheT
connectionandvalve.Thencloseallvalvesinthedischargeline.
Startthepumpandcontinueasoodedconditions.
overheatingoftheuidinthepumpandwilldamagetheCPVC
parts.Temperatureinthiscasewillincreaseupto220degrees.If
thepumpisbeingrunagainstacloseddischargevalveforalong
durationoftime,installasmallbleedlinebackintothereservoir
beforethedischargevalveofthepump.Ifthelineissmall,there
isaminimumpressureloss.Thispreventsoverheatingbyrecir
Installation&OperationInstructions

RecommendedInstallation

LiquidLevel
SuctionLevel
SuctionHead
Recommendedinstallation
foroptimalperformance
andendurance.
KEY
InTankInstallation
OutOfTankInstallation
LiquidLevel
RESERVOIR
2
1
2
1
Dischargeline
Suctionline
Suctionextension
1
2
1
2
Checkvalve
Discharge
valve
Valve
CheckValve
FlapperCheckValve
2
1
FlapperCheck
Valve
1
TConnection
withvalvefor
fillingupand
suctionline
Checkvalve
2

12
12H
H

*
*IncludesOring

SeriesPSparePartsList
P1/15 P1/6 P1/4 P1/2 P3/4 P1/2HP P3/4HP P1 P11/2 P2 P3 P5 P71/2
Item Description PartNo. PartNo. PartNo. PartNo. PartNo. PartNo. PartNo. PartNo. PartNo. PartNo. PartNo. PartNo. PartNo. 1Motor/ShaftAss’y
PhaseVoltageCycle 111550/60 P11501 P16001 123050/60 P11521 P16021  1110/22050/60 P1400103 1115/23060 P1200103 P3400103 P1200103 P3400103 P1000103 w/titaniumshaft P1200103T P3400103T P1200103T P3400103T P1000103T 1115/23050/60 P1202103 P3402103 P1202103 P3402103 P1002103 P1122103 w/titaniumshaft P1202103T P3402103T P1202103T P3402103T P1002103T P1122103T 3230/46050/60 P1403103 P1203103 P3403103 P1203103 P3403103 P1003103 P1123103 P2003103 P3003103K P5003103K P7123103K w/titaniumshaft P1203103T P3403103T P1203103T P3403103T P1003103T P1123103T P2003103T P3003103KT P5003103KT P7123103KT
1BS BearingSet P11501BS P14001BS P12001BS P12001BS P12001BS P12001BS P12001BS P12001BS P12001BS P30001BS P30001BS P30001BS 1EF ExternalFanw/SetScrew P11501EF P14001EF P12001EF P12001EF P12001EF P12001EF P12001EF P12001EF P12001EF P30001EF P30001EF P30001EF 1FC FanCover(w/DripShield P11501FC P14001FC P12001FC P12001FC P12001FC P12001FC P12001FC P12001FC P12001FC P30001FC P30001FC P30001FC
exceptP1/15,P1/6)
2MotorScrew/Bolts/WasherAss’y P11502(2) P16002(4) P14005(4) P12005(4) P12005(4) P12005(4) P12005(4) P12005(4) P12005(4) P12005(4) P30005K(4) P30005K(4) P30005K(4) 3Slinger P14002 P12002 P12002 P12002 P12002 P12002 P12002 P12002 P30002 P30002 P30002 4A MountingBracketCPVC P11504A P16004A
(AA/AS)
5MountingBracketScrew P11505(2) P16005(2) 6ChamberMounting P11506(2) P16006(2) P14006(2)
Screw(AA/AS/AAL)
7A PumpHousingAss’yCPVC P11507A P16007A P14007A P12006A P34006A P10007A P10007A P10007A P10007A P20007A P30006AK P30006AK P71206AK 7AL MountingBracketCPVC(A_AL) P14007AL 7B PumpHousingAss’yPolypro P11507B P16007B P14007B P12006B P34006B P10007B P10007B P10007B P10007B P20007B P30006BK P30006BK 7C PumpHousingAss’yPVDF P11507C P16007C P14007C P12006C P34006C P10007C P10007C P10007C P10007C P20007C P30006C P30006C P71206C 8A ImpellerCPVC P11508A P16008A P14008A P12007A P34007A P12008AHP P34008AHP P10008A P11208A P20008A P30007AK P50007AK P71207AK 8AK ImpellerCPVCw/nut P12008AHPK P34008AHPK P10008AK P11208AK P20008AK 8AT w/titaniuminsert P30007AKT P50007AKT P71207AKT 8B ImpellerPolypro P11508B P16008B P14008B P12007B P34007B P10008B P11208B P20008B 8BK ImpellerPolyprow/nut P10008BK P11208BK P20008BK 8C ImpellerPVDF P11508C P16008C P14008C P12007C P34007C P12008CHP P34008CHP P10008C P11208C P20008C P30007CK P50007CK P71207CK 8CK ImpellerPVDFw/nut P12008CHPK P34008CHPK P10008CK P11208CK P20008CK 8CT w/titaniuminsert P30007CKT P50007CKT P71207CKT 8V ImpellerORingViton N/A N/A N/A P12007V P12007V P12007V P12007V P12007V P12007V P12007V P30007V P30007V P30007V 9E HeadORingEPR P11509E P16009E P14009E P14009E P14009E P10009E P10009E P10009E P10009E P10009E P30011E(2) P30011E(2) P71211E(2) 9V HeadORingViton P11509V P16009V P14009V P14009V P14009V P10009V P10009V P10009V P10009V P10009V P30011V(2) P30011V(2) P71211V(2) 10A HeadCPVC P11510A P16010A P14010A P12009A P34009A P10010A P10010A P10010A P10010A P20010A P30010A P30010A P71210A 10B HeadPolypro P11510B P16010B P14010B P12009B P34009B P10010B P10010B P10010B P10010B P20010B P30010B P30010B P71210B 10C HeadPVDF P11510C P16010C P14010C P12009C P34009C P10010C P10010C P10010C P10010C P20010C P30010C P30010C P71210C 11V LipSealAss’yViton P11511V P11511V P14012V P12011V P12011V P12011V P12011V P12011V P12011V P12011V P30013V P30013V P30013V 12A SnapRingCPVC P16011A P14011A P12008A P12008A P10011A P10011A P10011A P10011A P10011A P30012A P30012A P71212A 12B SnapRingPolypro P16011B P14011B P12008B P12008B P10011B P10011B P10011B P10011B P10011B 12C SnapRingPVDF P16011C P14011C P12008C P12008C P10011C P10011C P10011C P10011C P10011C P30012C P30012C P71212C 13V ImpellerNutORingViton P30008VK P30008VK P30008VK 14A ImpellerNutAss’yCPVC P10014A* P10014A* P10014A* P10014A* P10014A* P30009AK P30009AK P30009AK 14AT w/titaniuminsert P30009AKT P30009AKT P30009AKT 14C ImpellerNutAss’yPVDF P10014C* P10014C* P10014C* P10014C* P10014C* P30009CK P30009CK P30009CK 14CT w/titaniuminsert P30009CKT P30009CKT P30009CKT 15T ShaftKeyTitanium P30015K P30015K P30015K 16A SnapRingScrewCPVC P10016A* P10016A* P10016A* P10016A* P10016A* P30016A P30016A P71216A 16B SnapRingScrewPolypro P10016B* P10016B* P10016B* P10016B* P10016B* P30016B P30016B 16C SnapRingScrewPVDF P10016C* P10016C* P10016C* P10016C* P10016C* P30016C P30016C P71216C 17A PumpHeadAss’yCPVC P11512A P16013A P14013A P12012A P34012A P12013AHP P34013AHP P10013A P11213A P20013A P30014AK P50014AK P71214AK 17AK PumpHeadAss’yCPVCw/nut P12013AHPK P34013AHPK P10013AK P11213AK P20013AK P30014AK P50014AK P71214AK 17AT w/titanium P30014AKT P50014AKT P71214AKT 17B PumpHeadAss’yPolypro P11512B P16013B P14013B P12012B P34012B P12013BHP P34013BHP P10013B P11213B P20013B P30014BK P50014BK P71214BK 17BK PumpHeadAss’yPolyprow/nut P12013BHPK P34013BHPK P10013BK P11213BK P20013BK P30014BK P50014BK P71214BK 17BT w/titanium P30014BKT P50014BKT P71214BKT 17C PumpHeadAss’yPVDF P11512C P16013C P14013C P12012C P34012C P12013CHP P34013CHP P10013C P11213C P20013C P30014CK P50014CK P71214CK 17CK PumpHeadAss’yPVDFw/nut P12013CHPK P34013CHPK P10013CK P11213CK P20013CK P30014CK P50014CK P71214CK 17CT w/titanium P30014CKT P50014CKT P71214CKT
*=IncludesOring

MaintenanceInstructions
MODEL:P1/15
DISASSEMBLY
1. Insertascrewdriverthroughthecenterholeattheendofthe
housingtoremovethehead.Pullwitharockingmotionto
remove.HeadOringcaneasilybereplaced.
2. Unscrewthethree(3)fancoverscrewsandremovethefan
cover.Withthepumpinahorizontalposition,holdthefan
withonehandorinsertascrewdriverinthecentermotorslot
andunscrewtheimpellercounterclockwiseusingngersor
thehandleendofapairofpliers.
3. Placingthepumpverticalwiththemotorontop,carefully
benddownonefanbladeinordertoexposethemotor
screw.Removemotorscrew.Rotatethefan180degrees
toexposesecondmotorscrewandremove.Motorand
housingarenowseparated.Donottrytoremoveshaftas
thisisanintegralpiecewiththemotorrotor.Lipsealcanbe
replaced.
ASSEMBLY
1. (NewMotor)Removefancoverandbenddownonefan
blade.(SeeDisassembly).Removeexistingmotorscrews
fromnewmotorandexchangewithscrewsfrommotorbeing
replaced.
2. Withthehousinginaverticalposition,mountingbracket
ontop,placemotorshaftintohousing.Thecordshouldbe
180degreesfromtheoutlet.Screwthemotorscrewsinto
theholesatthetopofthepumphousing.Themotorscrews
shouldnotbeovertightened.
3.Inserttheimpellerintothehousing.Withonehandonthe
fanandtheotherontheimpeller,turntheimpellerclockwise
withngersorhandleendofapairofpliersuntilimpeller
bottomsout.
4.Placethepumpuprightrestingonthemotor.Lookdown
intothehousingand,whilerotatingtheimpeller,checkto
seethattheimpelleriscentered.Theimpellermustnot
betouchingthesideofthehousing.Iftheimpellerisnot
centered,holdthemotorwithonehandandtapthehousing
withthemalletinthedirectionnecessarytoclearthehous
ing.
5.Finishscrewingthetwomotorscrews.Bendfanbladeback
tonormalposition.Replacethefancover.Insertthethree
(3)fancoverscrewsandtighten.Spintheimpellertocheck
thatthefanisnotrubbingagainstthecoverandfanbladeis
properlyinplace.(Donotoperatepumpuntilmotorfanand
pumpimpellerhavebeencheckedforposition.)
6.WetheadandheadOring.BesureheadOringisproperly
inplace.PlaceheadandheadOringintohousing.The
threadednippleshouldbetappedwithamalletuntilbottom
ingoutinthehousing.
MODEL:P1/6P1/4P1/2P3/4
DISASSEMBLY
1. Removethefrontsnapringattheendofthehousing
usingascrewdriverorapairofpliers.
2.Insertappropriatethreadedpipethroughthecenterhole
attheendofthehousingtoremovethehead.Pullwith
arockingmotiontoremove.HeadOringcaneasilybe
replaced.
3.Taketheplugoutfromthebackofthefancoveror
dripshield.Insertascrewdriverintheslotofthemotor
shaftandunscrewtheimpellercounterclockwiseusing
ngersorthehandleendofapairofpliers.
4.Removethefour(4)motorboltslocatedbeneaththe
motorbracket.Motorandhousingarenowseparated.
Donottrytoremoveshaftasthisisanintegralpiece
withthemotorrotor.Slingerandlipsealcanbere
placed.
ASSEMBLY
1.Withthemotorinaverticalposition,shaftupwards,
placehousingovershaft,liningupmotorboltholesin
mountingbracketwithholesinthemotor.Besurethe
slingerisproperlyplaced.Conduitboxshouldbe180
degreesfromtheoutlet.Screwthemotorboltsinto
theholesbeneaththemountingbracketinadiagonal
sequence.Besuremotorscrewsaretight.
2.Inserttheimpellerintothehousing.Withonehandhold
ingascrewdriverintheslotofthemotorshaftandthe
otherontheimpeller,turntheimpellerclockwisewith
ngersorhandleendofapairofpliersuntilimpeller
bottomsout.
3.Placethepumpuprightrestingonthemotor.Lookdown
intothehousingandwhilerotatingtheimpeller,checkto
seethattheimpelleriscentered.Theimpellermustnot
betouchingthesideofthehousing.
4.Replacepluginthebackofthefancoverordripshield.
5.WetheadandheadOring.BesureheadOringis
properlyinplace.Insertappropriatethreadedpipe
intoheadandreplaceintohousing.Thethreadedpipe
shouldbetappedwithamallet,pushingtheheadinto
thehousinguntilitbottomsout.OnModelsP1/2and
P3/4,pushtheheadintothehousinguntilsnapring
grooveisexposed.Removepipe
NOTE: ThismanualcoversseveraldifferentcongurationsofPSeriespumps.
 Besuretoselecttheappropriatemodelnumberforyourpump.

MaintenanceInstructions
MODEL:P1/2HP,P3/4HP,P1,P11/2,P2
NOTE:ThismanualcoversseveraldifferentconfigurationsofPSeriespumps.
 Besuretoselecttheappropriatemodelnumberforyourpump.
DISASSEMBLY
1. Removethefour(4)snapringscrews.Nowthesnapringcan
beremovedusingascrewdriverorapairofpliers.
2. Inserta2inchthreadedpipethroughthecenterholeattheend
ofthehousingtoremovethehead.Pullwitharockingmotionto
remove.HeadOringscaneasilybereplaced.
3. Unscrewthefancoverscrewsandremovethefancoverand
dripshield.Placethescrewdriverbetweenfanbladesand
unscrewtheimpellernutusinga3/4inchopenwrenchina
counterclockwiserotation.ImpellernutOringcanbereplaced.
4. Withthepumpinaverticalposition,impellerup,placeascrew
driverthroughthedischargeportwedgingbetweentheimpeller
topandthehousing.Carefullylifttheimpellerandremove.If
impellerdoesnotremoveeasily,proceedtostep5.
5. Removethefour(4)motorboltslocatedbeneaththemotor
bracket.Motorandhousingarenowseparated.Donottryto
removeshaftasthisisanintegralpiecewiththemotorrotor.
Slingerandlipsealcanbereplaced.Usingarubbermallethit
thepumpbracketlightly,topsidefacingmotor,untiltheimpeller
andkeywaypoploose.
ASSEMBLY
1. Withthemotorinaverticalposition,shaftupwards,placehous
ingovershaft,liningupmotorboltholesinthemountingbracket
withholesinthemotor.Besuretheslingerisproperlyinplace.
Screwthemotorboltsintotheholesbeneaththemounting
bracketinadiagonalsequence.
Besuremotorscrewsaretight.
2. Inserttheimpellerintothehousinguntilitbottomsout.Donot
hammertheimpellerandsleevedownontheshaft.Lineupthe
keywayandinsertkeybylightlytappingitwithahammer.Screw
theimpellernutclockwiseholdingimpeller.Besureimpellernut
Oringisproperlyinplace.Afterhandtight,turnwithwrench180
degrees.
DONOTOVERTIGHTEN.
3. Replacethefancoveranddripshield.Insertthefancover
screwsandtighten.Besurefanisnotrubbingagainstfancover.
4. Placethepumpuprightrestingonthemotor.Lookdownintothe
housingand,whilerotatingtheimpeller,checktoseethatthe
impelleriscentered.Theimpellermustnotbetouchingtheside
ofthehousing.
5. WetheadandheadOrings.BesureheadOringsareproperly
inplace.Insert2inchthreadedpipeintotheheadandreplace
inhousing.Thethreadedpipeshouldbetappedwithamallet,
pushingtheheadintothehousinguntilthesnapringgroove
isexposed.
Removepipe
andreplace
snapring.Line
upthrough
holesinsnap
ringwiththe
threadedholes
inthehead
byrotating
thesnapring
counterclock
wise.Insert
andtightenthe
four(4)snap
ringscrews.
DISASSEMBLY
1. Removethefour(4)snapringscrews,beingcarefulnottolose
theOrings.Removethesnapringusingascrewdriverora
pairofpliers.
2. Inserttheappropriatethreadedpipethroughthecenterhole
attheendofthehousingtoremovethehead.Pullwitharock
ingmotiontoremove.HeadOringcaneasilybereplaced.
3. Taketheplugoutfromthebackofthefancoverordripshield.
Removeimpellernutassemblyusinga7/16”wrench.Inserta
screwdriverintheslotofthemotorshaftandunscrewthe
impellercounterclockwiseusingngersorthehandleendofa
pairofpliers.
4. Removethefour(4)motorboltslocatedbeneaththemotor
bracket.Motorandhousingarenowseparated.Donottryto
removetheshaftasthisisanintegralpiecewiththemotorro
tor.Slingerandlipsealcanbereplaced.

ASSEMBLY
1. Withthemotorinaverticalposition,shaftupwards,place
housingovertheshaft,liningupmotorboltholesinthe
mountingbracketwithholesinthemotor.Besuretheslinger
isproperlyinplace.Conduitboxshouldbe180˚fromthe
outlet.Screwthemotorboltsintotheholesbeneaththe
mountingbracketinadiagonalsequence.Besuremotor
screwsaretight.
2. Inserttheimpellerintothehousing.Withonehandholding
ascrewdriverintheslotofthemotorshaftandtheotherhand
ontheimpeller,turntheimpellerclockwisewithngersorthe
hankleendofapairofpliersuntiltheimpellerbottomsout.
3. AttachimpellernutassemblytoshaftwithimpellernutOring
usinga7/16”wrench.
4. Placethepumpuprightrestingonthemotor.Lookdown
intothehousingandwhilerotatingtheimpeller,checkto
seethattheimpelleriscentered.
Theimpellermustnotbetouchingthesideofthehousing.
5. Replacepluginthebackofthefancoverordripshield.Wet
headandheadOring.BesureheadOringisproperlyin
place.Inserttheappropriatethreadedpipeintoheadand
replaceinhousing.Thethreadedpipeshouldbetappedwith
amallet,pushingtheheadintothehousinguntilthesnap
ringgroveisexposed.Removepipeandreplacesnap
ring.Lineupthroughholesinthesnapringwiththethreaded
holesintheheadbyrotatingthesnapringscountercloclwise.
Insertandtightenthefour(4)snapringscrews.
71/2”
73/8”
(ref)
3”
41/2”51/2”
1”
3/8”ø
15/16”
Mounting Diagram P3  P7 1/2
Mounting Diagram P1/2  P2
6.50”
4SLOTS
.34WIDE
4.88”
4.32”
3”
MODEL:P3,P5,P71/2

ModelD05PPSP
Look! Penguin Pumps extended products
HighFlowVerticalPump
SeriesPHF
Flowsto400gpm
CorrosionresistantCPVCconstruc
tion. No metal contact. No pump
bearings, bushings or seals. Self
primingwhenimmersed.Runsdry
without damage. Temperatures to
180ºF.
Bulletin201
CPVCHorizontal
CentrifugalPumps
SeriesHV&HN
Flowsto181gpm
True volute design featuring the
latest hydraulic technology  en
ergyefciency, high owand high
pressure.CPVCconstructionwhere
in contact with solution. No metal
contact.All models available with
doublemechanicalseal andwater
ush. Temperatures to 180ºF. Op
tional priming chambers available
forSeriesHV.
Bulletin202/210
SeallessMagneticDrivePumps
SeriesM&MT
Flowsto250gpm
Corrosionresistant,leakproof,seal
lessmagneticdrivepumpswithows
to 200 gpm. Series M constructed
of polypropylene and/or ryton with
optional316SS,Kynar or Hastelloy
construction.Series MT pumps are
constructed of polypropylene or
PVDF and can handle caustics to
220ºF.Compatiblewithawiderange
ofacidsandalkalies.
Bulletin203/213
CPVC2stageand3stage
HorizontalDiffuserPumps
SeriesHD
Flowsto104gpm
Pressureto150TDHinfeet
A multistage pump in plastic. De
signedforhigherpressureapplica
tions, where a metal pump is not
acceptable.CPVCconstructionand
optional titanium shaft allows for
temperaturesto180ºF.Multistage
pumpsareavailablein2stageand
3stagein11/2hp,2hp,and3hp.
SeriesHDoffersincreasedefcien
cywithsmallerpumpcases.
Bulletin206
PolypropyleneHorizontal
CentrifugalPumps
SeriesHOM
Flowsto132gpm
These glass fiber reinforced poly
propylene pumps with a simple en
ergysavingvolutedesignoffereasy
maintenance and high operational
efciency. Ideal formany OEM and
chemical processing applications.
A completely metalless diplo seal
providesreliabilityandeasyinstalla
tion.TheVclampwithknoballowsfor
easyassemblyanddissasembly.
Bulletin209
316StainlessSteel
CentrifugalPump
SeriesHSC
Flowsto140gpm
Corrosion resistant, stainless steel
pumps ideal for many OEM and
chemical processing applications.
They feature high operational ef
ciencyandeasymaintenance,and
areavailablewithasinglemechani
cal seal or double mechanical seal
with water ush. Multistage model
alsoavailableforhighpressures to
140TDH.
Bulletin208
ModelHD23V
ModelHOM1/2E
ModelHSC1/2SV
ModelP71/2HF
ModelHN5S
ModelMT2C
ModelHV3/4DV
ModelM3/4B
316SS
SeriesPSS
These 316 stainless steel vertical
pumpsutilizeareplaceablecoupled
shaft using multiple set screws
to minimize shaft deflection and
misalignmentassociatedproblems.
Whileallowingtheuseofstandard
MEMA motors, which are readily
availableatmostlocalmotorsuppli
ers,thussavingprolongeddowntime
andmoney.
Bulletin214
AirOperatedDoubleDiaphragm
SeriesD
Flowsto155gpm
Thesenewpumpsaredesigned
toreducedowntimebyensuring
continuous,reliablepumpperfor
mance.Inadditiontoeleminating
freezingandstalling,theyareself
priming,andcanhandleinnite
variableowsupto90%solids,
andarecapableofoperatingas
lowasonestrokeperminute.
Bulletin217