Penn Scale CM-101 User manual

PENN SCALE
CM-101 Price Computing Scale
Penn Scale Mfg. Co., Inc.
150 W. Berks Street
Philadelphia, PA 19122
Phone: [phone]
Fax: [phone]
Specification
Model
CM - 101
Capacity
30.00 x 0.01 lb / 15.000 x 0.005 kg
Display
LCD ( 5 / 5 / 6 )
Op. Temp.
0 C ~ 35 C / 32 F ~ 95 F
Dimension
Platter
300 x 250 mm / 11.8 x 9.8 “
Height
110 mm / 4.3 “
Length
335 mm / 13.1 “
Width
320 mm / 12.5 “
Power
DC
4 V / 4 Ah Rechargeable Battery
AC
120 V 50 / 60 Hz
Connecter
Standard AC power connecter
Charge Life
120 hrs
Calibration Procedure
( Authorized License Dealer only )
Step 1. Turn the scale Power ON
Step 2. While the scale is in Testing Mode,
press TARE key
Step 3. Enter PASS-WORD
Step 4. When the scale displays
“ c a l , f 1 “, press TARE key
Step 5. When the scale displays “ Uload”,
press TARE key with nothing on
the platter,
Step 6. When the scale displays “ load “ ,
place 30 lb weight on the Platter,
then press TARE
the scale will display “span pass”
< Note >
This procedure must be performed ONLY by the
authorized licensed personnel
If done by other, the field inspector from W & M
may NULLIFY the validity of the scale
Legal for Trade
Certificate #04-101A1
Method to check the voltage condition
Method 1:
After the self-checking when you switch on the scale, the
price window will display: DC *.** (the voltage now)
Method 2:
During the process of usage, you can press the * key
and 00 key meanwhile, then the price window will
display: DC *.** (the voltage now),then you can press
any key to be back to the normal weighing condition.

PENN SCALE Operation
CM - 101 : Price Computing Scale
Operating the Scale
1. Make sure that the scale is plugged into the proper outlet
2. Make sure that there is nothing on the scale platter
3. Turn the Scale Power ON, then the scale will run through a
self test, count down to zero, and displays zeros
( The Initial State --- operation-ready-state )
1.23
2.00
1.23
1.23.
2.46
0.00
0.00
0.00
0.00
-
0.01
0.00
1.00
Weighing
1. Enter a unit price
2. Place an item on the platter
3. Remove the item from the platter
Steps 1 & 2 can be interchanged.
After Step 2, the TOTAL PRICE will show the
calculated amount
After step 3, the scale will return to Initial State
Weighing with known TARE
1 Enter a TARE weight through the keys
2. Press TARE key
3. Enter a unit price
4. Place an item on the platter
5. Remove the item from the platter
Steps 3 & 4 can be interchanged.
After Step 2, the NET light will come on indicating
that the weight shown is a net weight
After Step 4, the TOTAL PRICE will show the
calculated amount
For example ; After Step 2,
After step 4, the display may look like this;
After step 5, the scale will return to Initial State
Weighing with Unknown TARE
1 Place the container on the platter
2. Press TARE key
3. Enter a unit price
4. Place an item on the platter
5. Remove the item from the platter
Steps 3 & 4 can be interchanged.
After Step 2, the NET light will come on indicating
that the weight shown is a net weight
After Step 4, the TOTAL PRICE will show the
calculated amount
For example ; After Step 2,
After step 4, the display may look like this;
After step 5, the scale will return to Initial State
Lamp & Keypad
NET Lamp When ON, it indicates that there is a TARE set
and the displayed weight is a net weight
ZERO Lamp When ON, it indicates that the scale is at Gross
Zero.
SAVE Lamp When ON, it indicates that the auto-clearing
feature is disabled. ( save TARE, UNIT price )
BATT Lamp When ON, it indicates that the scale has less than
30 minutes of operating time left and the scale
will turn itself off if the battery charge is too low
C Clear Key , used to clear erroneous entries
and to release error condition
ZERO Zero key, used to manually set the zero point
TARE Tare key, used to enter or clear tare weight
If pressed before any operation, the SAVE
SAVE Lamp will come on. This will prevent the
Weight and Unit Price displays from
auto-clearing
* * key, reserved for future use
-
0.01
0.00
0.00
1.00
2.34
2.34

Penn Scale CM-101
Price Computing Scale
 The Leader for Price-Performance
 Tactile Key-Pad Switches
 TARE, ZERO, SAVE, CLEAR Keys
 Large LCD Display
 Initial, Auto and Semi-auto Zero Setting
 Lb / Kg weighing unit
 Continuous TARE setting function
 AC / DC Power with standard Power cable
 Back-Light and Auto Display setting
 Capacity 30.00 x 0.01 lbs
 User friendly and Simple to operate
ONE YEAR WARRANTY
Penn Scale Manufacturing Company
Scales and Scoops
150 West Berks Street
Philadelphia, PA 19122
Phone: [phone]
Fax: [phone]
[email protected]
www.pennscale.com
Since 1923
Legal For Trade