Pentair jung pumpen Multistream series User manual

EN Instruction Manual

MULTISTREAM

10/2 A1 15/2 A1 25/2 A2 35/2 A2 25/2 B1 35/2 B2

10/4 B1 15/4 B3 25/4 B4 35/4 B4 25/4 C1 35/4 C1

10/2 A1 EX 15/2 A1 EX 25/2 A2 EX 35/2 A2 EX 25/2 B1 EX 35/2 B2 EX

10/4 B1 EX 15/4 B3 EX 25/4 B4 EX 35/4 B4 EX 25/4 C1 EX 35/4 C1 EX

UC 25/4 C1 UC 35/2 B2 UC 35/4 C1

15/26 A1 25/26 A2 10/46 B1 15/46 B3 25/46 B4

JUNG-PUMPEN.DE B 41992-26-1810

ENGLISH

You have purchased a product made by Pentair Jung Pum-

pen and with it, therefore, also excellent quality and service.

Secure this service by carrying out the installation works

in accordance with the instructions, so that our product

can perform its task to your complete satisfaction. Please

remember that damage caused by incorrect installation or

handling will adversely affect the guarantee. Therefore ple-

ase adhere to the instructions in this manual!

This appliance can be used by children aged 8 years or over

and by persons with limited physical, sensory or intellectual

capabilities, or with limited experience and knowledge, pro-

vided that they are supervised or have been instructed in

the safe use of the appliance and are aware of the dangers

involved. Children must not be allowed to play with the ap-

pliance. Cleaning and user maintenance must not be carried

out by children unless they are supervised.

Damage prevention in case of failure

Like any other electrical device, this product may fail due to a

lack of mains voltage or a technical defect.

If damage (including consequential damage) can occur as a re-

sult of product failure, the following precautions can be taken

at your discretion:

•Installation of a water level dependent (under circumstan-

ces, mains-independent) alarm system, so that the alarm

can be heard before damage occurs.

•Inspection of the collecting tank/chamber for tightness up

to the top edge before – or at the latest, during – installation

or operation of the product.

•Installation of backow protection for drainage units that

can be damaged by wastewater leakage upon product

failure.

•Installation of a further product that can compensate in

case of failure of the other product (e.g. duplex unit).

•Installation of an emergency power generator.

As these precautions serve to prevent or minimise consequenti-

al damage upon product failure, they are to be strictly observed

as the manufacturer’s guideline – in line with the standard DIN EN

specications as state of the art – when using the product (Hig-

her Regional Court Frankfurt/Main, Ref.: 2 U 205/11, 06/15/2012).

SAFETY INSTRUCTIONS

This instruction manual contains essential information that must

be observed during installation, operation and servicing. It is

therefore important that the installer and the responsible techni-

cian/operator read this instruction manual before the equipment

is installed and put into operation. The manual must always be

available at the location where the pump or the plant is installed.

Failure to observe the safety instructions can lead to the loss of

all indemnity.

In this instruction manual, safety information is distinctly labelled

with particular symbols. Disregarding this information can be

dangerous.

General danger to people!

Warning of electrical voltage!

NOTICE!

Danger to equipment and operation!

Qualication and training of personnel

All personnel involved with the operation, servicing, inspection

and installation of the equipment must be suitably qualied

for this work and must have studied the instruction manual in

depth to ensure that they are suciently conversant with its

contents. The supervision, competence and areas of responsi-

bility of the personnel must be precisely regulated by the ope-

rator. If the personnel do not have the necessary skills, they

must be instructed and trained accordingly.

Safety-conscious working

The safety instructions in this instruction manual, the existing na-

tional regulations regarding accident prevention, and any internal

working, operating and safety regulations must be adhered to.

Safety instructions for the operator/user

All legal regulations, local directives and safety regulations

must be adhered to.

The possibility of danger due to electrical energy must be pre-

vented. Leakages of dangerous (e.g. explosive, toxic, hot) sub-

stances must be discharged such that no danger to people or

the environment occurs. Legal regulations must be observed.

Safety instructions for installation, inspection and

maintenance works

As a basic principle, works may only be carried out to the equip-

ment when it is shut down. Pumps or plant that convey harmful

substances must be decontaminated.

All safety and protection components must be re-tted and/or

made operational immediately after the works have been com-

pleted. Their effectiveness must be checked before restarting,

taking into account the current regulations and stipulations.

Unauthorised modications, manufacture of spare parts

The equipment may only be modied or altered in agreement

with the manufacturer. The use of original spare parts and ac-

cessories approved by the manufacturer is important for sa-

fety reasons. The use of other parts can result in liability for

consequential damage being rescinded.

Unauthorised operating methods

The operational safety of the supplied equipment is only gua-

ranteed if the equipment is used for its intended purpose. The

limiting values given in the "Technical Data" section may not be

exceeded under any circumstances.

Instructions regarding accident prevention

Before commencing servicing or maintenance works, cordon

off the working area and check that the lifting gear is in perfect

condition.

Never work alone. Always wear a hard hat, safety glasses and

safety shoes and, if necessary, a suitable safety belt.

Before carrying out welding works or using electrical devices,

check to ensure there is no danger of explosion.

People working in wastewater systems must be vaccinated

against the pathogens that may be found there. For the sake of

your health, be sure to pay meticulous attention to cleanliness

wherever you are working.

Make sure that there are no toxic gases in the working area.

Observe the health and safety at work regulations and make

sure that a rst-aid kit is to hand.

In some cases, the pump and the pumping medium may be hot

and could cause burns.

For installations in areas subject to explosion hazards, special

regulations apply!

ENGLISH

AREAS OF APPLICATION

Submersible pumps in the MultiStream range are suitable for

pumping wastewater in municipal and industrial pumping sta-

tions, and in rainwater retention tanks. The smallest models

also perform well in disaster control applications.

MultiStream pumps are favoured for use with:

–wastewater containing bres

– wastewater containing solids (without stones)

– mixed wastewater

– untreated water

– raw sludge

– surface water and rainwater

The submersible pumps are supplied without explosion pro-

tection or with explosion protection.

When using the pumps, the relevant national laws, regulations

and stipulations must be adhered to, for example:

•Installation of low-voltage systems

(e.g., VDE 0100 in Germany)

•Safety and working materials

(e.g., BetrSichV and BGR 500 in Germany)

•Safety in wastewater systems

(e.g., GUV-VC5, GUV-R104 and GUV-R126 in Germany)

•Electrical systems and operating resources

(e.g., GUV-VA3 in Germany)

•Explosion protection

EN 60079-0, EN 60079-1, EN 60079-14, EN 1127-1.

For non-standard utilisation conditions in areas subject to ex-

plosion hazards, please ask the local authority responsible.

In Germany, this would be, for example, the Trade Supervisory

Centre (Gewerbeaufsicht), the Technical Inspection Agency

(TÜV), the building authority (Bauamt) or professional organi-

sation (Berufsgenossenschaft).

The installation and operation of this equipment is regulated by

the ordinance concerning the protection of health and safety in

the provision of work equipment and its use at work, concerning

safety when operating installations subject to monitoring, and

concerning the organisation of industrial health and safety at

work, (Betriebssicherheitsverordnung), Article 1.

Where no explosion protection is stipulated for the pumping

of foul wastewater at the installation location, pumps without

explosion protection may also be used.

Modes of operation

with the pumped medium at a temperature of 40°C:

Motor submersed: continuous operation S1;

Motor emerged: short duration operation S2;

see "Technical Data"

Motor emerged: intermittent operation S3;

see "Technical Data"

The submersible pump is frost-resistant down to -20°C when

stored in dry conditions. When installed, however, it must not

be allowed to freeze in the water.

Transport

The pump must always be lifted by the shackle and never by the

power supply cable! The pump should only be lowered by using

a rope or chain.

ELECTRICAL CONNECTION

Δ-Circuitry, low voltage

Y-Circuitry, high voltage

Alterations to the circuitry are to be made using crimp con-

nectors (X) between the coni plug connection (Y) and the built-

in motor. The new crimp connection must be professionally

made.

By using our controls, you can be sure that the requirements of

the EU-type-testing certicate are met.

NOTICE! Only qualied electricians may carry out electrical

works to the pump or the controls.

NOTICE! The standards applicable in each case (e.g. EN), the

country-specic regulations (e.g. VDE in Germany), and the

regulations of the local supply network operator must be ob-

served.

NOTICE! Never lay the end of cables in water! Penetrating wa-

ter may cause malfunctions.

Only slow-blow fuses or automatic fuses with C or D character-

istics are to be used as pre-fuses for the pump. Necessary fuse

protection for direct on-line start: 10 A.

The pump must be protected via an overload trip. Setting for

direct on-line start = nominal current.

If the protective device has been triggered, the cause of the

malfunction must be eliminated before switching on again.

Coil thermostats

NOTICE! In addition to the overload trip or protective switch

of the motor, the thermostats integrated in the motor winding

must also be connected. The thermostats are suitable for 250

V / 1.2 A (cos phi = 0.6) and are labelled 30 and 32 for connection

purposes.

Thermostat connection without explosion

protection

The thermostats are to be connected in such a way that the

ENGLISH

motor is switched off via the control circuit when the response

temperature is reached. The motor is switched on again auto-

matically after the winding has cooled down.

Thermostat connection with explosion

protection

The thermostats are to be connected in such a way that the

motor is switched off via the control circuit when the response

temperature is reached. It must not be possible for the motor

to switch on again automatically after the winding has cooled

down.

WARNING!

After an automatic cut-out via the temperature limiters, the

cause of the malfunction must rst be eliminated. Only then

may the motor be switched on again manually.

The restart interlock must be "non-resetting on power failure",

i.e. the lock must be in place to prevent restarting even after a

power cut (in Europe: Directive 2014/34/EU, Appendix II 1.5, EN

60079-17 Table1, B10).

Operation with frequency converter

Frequency converters may only be used for controlling the fre-

quency of special models of three-phase pumps.

NOTICE! For physical reasons, pumps may not be operated at a

higher frequency than that shown on the type plate. If the fre-

quency increases beyond the value on the type plate, the pow-

er input increases and the motor is then overloaded.

For special models of three-phase pumps that are designed for

frequency converter operation, the motor type shown on the

type plate is labelled with an additional "K" (e.g. D90-2/75 CK).

These pumps also have a sticker on the end of the cable that

indicates their suitability for use with a frequency converter.

These motors are tted with PTC thermistors as winding pro-

tectors. Voltages of more than 2.5 V may not be connected to

the winding protection terminals 40 and 41! For explosion pro-

tected pumps, a type-tested tripping unit that complies with

the EU type-testing requirements is also necessary.

Rotational direction

The rotational direction must be checked before installation! If

the rotational direction is correct, the start-up jolt should be in

the opposite direction to the rotational direction arrow on the

motor housing. The wrong rotational direction is also indicated

if the pump performs inadequately when installed, or if loud

noises can be heard during operation. If the rotational direc-

tion is wrong, 2 phases of the supply cable must be swapped

over.

CAUTION!

The start-up jolt can be very forceful.

Potential equalisation

To comply with EN 60079-14 and EN 1127-1, an additional equi-

potential bonding must be installed for facilities with protec-

tive earth conductors in TN/TT networks in areas subject to

explosion hazards. In Germany, for example, the design must

be in accordance with VDE 0100, Part 540 (Association of Ger-

man Electrical Engineers).

No additional potential equalisation is required on site for

JUNG PUMPEN concrete or plastic chambers in explosion

zones 1 and 2 (statement made by TÜV Nord (Technical Inspec-

tion Agency) in March 2008).

Exception: if conductive parts, such as cable protection

sleeves made of corrugated pipe or a pressure pipe made of

metal, are connected to the chamber from the outside. In this

case, an electrically conductive connection must be made be-

tween the conductive parts and the housing of the pump(s).

For corrosion protection reasons, the connection should be

made using stainless steel.

Explosion protected pumps have a special connection point at

the cable entry point.

INSTALLATION

NOTICE! Before the pump can be installed, the 4 plastic pa-

ckaging feet must be unscrewed from the bottom of the pump

housing and removed.

The pump must be installed as shown in the examples. For in-

stallations in accordance with EN 12056-4, the pressure pipe

must be laid in a loop above the local back pressure level and

protected with a back pressure prevention valve.

Example installation with guide rail system

Assembly: Fix the coupling base rmly to the oor of the col-

lection chamber using plugs and then mount the guide rails.

Next, install the pressure pipe including the necessary ttings,

such as the non-return valve and shut-off valves.

Finally, t the pump with the screwed-on coupling catch on to

the guide rails and lower it into place using a chain xed to the

shackle.

A xing facility for lifting gear should be provided above the

chamber opening at a sucient height.

Level monitoring can be carried out using various systems.

Their specic characteristics and requirements can be found

in the relevant operating manuals.

WARNING!

In accordance with the explosion protection laws and regula-

tions, JUNG Ex-pumps should never be allowed to run dry or to

operate in "snore" mode.

The pump must switch off when the water level sinks to the

upper edge of the pump housing (x in the illustration), at the

very latest. This shut-down must be implemented via a sepa-

rate switching circuit. Dry running for servicing or inspection

purposes may only take place outside the potentially explosive

area.

A correspondingly larger diameter pipe should be used for

longer pressure pipelines to avoid pipe friction losses.

Rising pressure pipes must be protected from frost! A cham-

ber cover must be selected that is suitable for the intended use

ENGLISH

and has the required load-bearing capacity.

If necessary, the pump housing can be ventilated by unscrew-

ing the "Luft" sealing screw. A ushing pipe, available as an ac-

cessory, can be installed to minimise deposits and the forma-

tion of oating layers in the chamber.

If the pump is malfunctioning, part of the contents of the oil

reservoir could escape into the pumping medium.

Not Ex-pumps. If a hose is used as a pressure line, care must

be taken to ensure that for every pumping operation the hose

is completely empty before the pump is submersed. Any resid-

ual liquid would obstruct the ventilation of the pump housing

and therefore also hinder the pumping operation.

This situation can also occur if the pump runs dry, pumps down

to a lower lever than that shown in the installation drawing, or

runs in "snore" mode during the daily test run.

In these cases, the pump housing must be ventilated by un-

screwing the "Luft" sealing screw.

SERVICING

Maintenance and inspection of this product must be carried

out in accordance with EN 12056-4 and EN 60074-19.

To ensure continued reliability of service, we recommend that

you take out a service contract.

WARNING!

Before carrying out any works: disconnect the pump and the

controls from the mains and take steps to ensure that it cannot

be emergized again.

WARNING!

Check the mains cable for signs of mechanical and chemical

damage. Damaged or kinked cables must be replaced.

NOTICE! When using a chain to lift the pump, please observe

the relevant national regulations regarding accident preventi-

on. Lifting gear must be checked regularly by an expert in ac-

cordance with the legal regulations.

NOTICE! Motors in the Ex-range conform to the "ameproof

enclosures" ignition protection category. Maintenance works

that affect the explosion protection may only be carried out by

authorised specialists or by the manufacturer. When carrying

out repairs, all areas next to ameproof gaps must be checked

for damages and, if necessary, replaced by genuine parts.

Oil check

The drain plug is labelled "Öl". In order to check the mechanical

seal, the oil, including any residue, must be drained from the oil

reservoir and collected in a clean measuring container.

•If the oil is contaminated with water (milky), an oil change

must be carried out. Check again after a further 300 operat-

ing hours, but at the very latest after 6 months!

•However, if the oil is contaminated with both water and

pollutants, then not only the oil must be replaced, but the

mechanical seal as well.

For monitoring the oil reservoir, it is also possible to retrot the

electrode of our "DKG" or "DKG-Ex" seal leak control device in

place of the "DKG" sealing screw.

Changing the oil

To ensure operational liability, the rst oil change should be

carried out after 300 operating hours, with further oil changes

carried out after every 1000 operating hours.

If the number of operating hours is very low, an oil change

should still be carried out at least once a year.

If wastewater with strongly abrasive constituents is being

pumped, the oil changes should be carried out at correspond-

ingly shorter intervals.

Use HLP hydraulic mineral oil, viscosity class 22 to 46, e.g. Mo-

bil DTE 22, DTE 24, DTE 25, to replace the oil in the oil reservoir.

The quantity of oil required is 1000 cm³, except for A1 and B1

pumps, which must be lled with 800 cm³.

The oil reservoir may only be lled with the specied quantity

of oil. Overlling will result in the pump being rendered inoper-

able.

Cleaning

To clean the impeller and the spiral housing, simply remove the

4 hexagonal screws and lift the motor unit off the spiral hous-

ing

CAUTION!

Worn impellers can have sharp edges.

NOTICE! If the wrong screws are unscrewed, the oil will run out

of the oil reservoir.

Tightening torque MAfor A2 screw materials

for M 6 MA= 8 Nm

for M 8 MA= 20 Nm

for M 10 MA= 40 Nm

for M 12 MA= 70 Nm

Checking the pump unit

The housing screws for the pump, and the connecting and x-

ing screws of the installation must be checked to ensure they

are xed securely. They should be tightened if necessary.

If the pump performance decreases, or if increasingly loud

noises can be heard during operation, the gap dimension be-

tween the impeller face and the wear plate must be checked

for wear by an expert and replaced if necessary. Nominal di-

mension: 0.5 - 0.8 mm.

ENGLISH

Adjust the impeller gap

1. Block the impeller.

2. Loosen the central impeller screw located in the impeller

hub.

3. Loosen the impeller by knocking it gently with a hammer.

4. Tighten the impeller screw until it is “hand tight”.

5. Adjust the impeller gap by pulling the impeller down to the

nominal dimension 0.5 - 0.8 mm.

6. Block the impeller again and tighten the impeller screw to

65 Nm.

The maximum adjustment possible is 3 mm

Replace the wear plate (...B2, ...B4, ...C1)

1. Loosen the four cylinder head screws on the wear plate on

the lower pump case.

2. Take out the old wear plate with the seal.

3. Clean the wear plate seat and insert the new wear plate with

a new seal.

4. Tighten the four cylinder head screws again.

5. After this, readjust the impeller gap again.

Replacing the impeller

CAUTION!

Worn impellers can have sharp edges.

1. Remove the 4 hexagonal screws and lift the motor unit off

the spiral housing.

2. Block the impeller.

3. Loosen the central impeller screw located in the impeller

hub.

4. Loosen the impeller by knocking it gently with a hammer

and then slide it off the shaft.

5. Clean all the parts of the impeller mounting.

6. Grease the shaft cover on the inside. NOTICE! Do not use

grease containing graphite, such as "Molykote".

7. Fix all the parts of the impeller mounting in place and tight-

en the impeller screw until it is “hand tight”.

8. Slide the new impeller over the preassembled impeller

mounting onto the shaft.

9. Mount the motor unit on the spiral housing; the cable entry

point is opposite the discharge branch.

10.Set the gap dimension to 0.5 - 0.8 mm and then tighten the

impeller screw to 65 Nm.

WHAT TO DO IN THE EVENT OF

ANY PROBLEMS

Pump does not work

•Check mains current (do not use a pin gauge)

•Fuse faulty = may be too weak (please refer to Electrical

Connection)

•Mains supply cable damaged = repair to be carried out by

manufacturer only

Pump runs but does not pump

•Empty pressure pipe or hose to allow the non-return valve

to open and let the air escape from the pump housing.

•Ventilate the pump housing by unscrewing the "Luft" (air)

sealing screw.

The impeller is blocked

•Solids and brous matter have become lodged in the pump

housing (please refer to Maintenance)

Decreased pumping performance

•The impeller is blocked (please refer to maintenance)

•Rotor gap too large = adjust

•The impeller is worn out = replace it

•Wrong direction of rotation = change 2 phases of the power

supply

A B C D E F

10/2 A1 475 325 110 105 135 175

15/2 A1 475 325 110 105 135 175

25/2 A2 475 345 135 135 135 185

35/2 A2 510 345 135 135 135 185

25/2 B1 530 340 135 135 185 240

35/2 B2 570 380 145 135 185 240

10/4 B1 530 340 135 135 185 240

15/4 B3 535 380 160 160 185 240

25/4 B4 535 440 190 160 185 240

35/4 B4 570 440 190 160 185 240

25/4 C1 600 450 195 195 235 305

35/4 C1 635 450 195 195 235 305

10/2 A1 15/2 A1 25/2 A2 35/2 A2 25/2 B1 35/2 B2

[kg] 41 42 48 52 45 55

PN 6 /10 DN 65 DN 65 DN 65 DN 65 DN 80 DN 80

[mm] 40 40 40 40 70 70

S2 40 min. 32 min. 26 min. 27 min. 26 min. 27 min.

S3* 60 % 50 % 40 % 40 % 40 % 40 %

EX D 90-2/75 D 90-2/75 D 90-2/75 D 90-2/110 D 90-2/75 D 90-2/110

Motor 08 ATEX 1113 X01 08 ATEX 1113 X01 08 ATEX 1113 X01 08 ATEX 1113 X01 08 ATEX 1113 X01 08 ATEX 1113 X01

II 2 G Ex db IIB T4 Gb Ex db IIB T4 Gb Ex db IIB T4 Gb Ex db IIB T4 Gb Ex db IIB T4 Gb Ex db IIB T4 Gb

P1 / P2 [kW] 1,3 / 1,1 1,8 / 1,5 2,6 / 2,1 3,7 / 3,2 2,6 / 2,2 3,7 / 3,2

U [V] 3/PE x 400 3/PE x 400 3/PE x 400 3/PE x 400 3/PE x 400 3/PE x 400

f [Hz] 50 50 50 50 50 50

I [A] 2,7 3,2 4,4 6,5 4,4 6,5

cos phi 0,72 0,81 0,86 0,83 0,86 0,83

n [min-1]2900 2860 2800 2890 2800 2890

* Beispiel: 40% = 4 min Betrieb + 6 min Pause (Spieldauer 10 min)

* Example for 40%: 4 min. operation and 6 min. rest (Cycle duration 10 min.)

* Exemple: 40%= 4 min de service et 6 min de pause (Durée du jeu 10 min)

* Esempio: 40%: 4 min. di funzionamento + 6 min. di pausa (durata del ciclo 10 min.)

* Przykładowo 40%: 4 min pracy i 6 min przerwy (Czas cyklu 10 min)

* Příklad 40%: 4 min. provoz a 6 min. přestávka (trvání pracovního cyklu 10 min.)

* Príklad 40%: 4 min prevádzka a 6 min prestávka (doba trvania cyklu 10 min)

* 4 perc üzem és 6 perc szünet (ciklusidő 10 perc)

* Exemplu 40%: 4 min funcţionare şi 6 min pauză (timp aproximativ 10 min)

Technische Daten | Technical data | Caractéristiques techniques | Dati tecnici | Technische

10/4 B1 15/4 B3 25/4 B4 35/4 B4 25/4 C1 35/4 C1

[kg] 45 50

59 62 63 67

PN 6 /10 DN 80 DN 80

DN 80 DN 80 DN 100 DN 100

[mm] 70 70

70 70 100 100

S2 45 min. 35 min.

15 min. 16 min. 20 min. 16 min.

S3* 50 % 40 %

25 % 25 % 30 % 25 %

EX D 90-4/ 75 D 90-4/75

D 90-4/75 D 90-4/110 D 90-4/75 D 90-4/110

Motor 08 ATEX 1113 X01 08 ATEX 1113 X01 08 ATEX 1113 X01 08 ATEX 1113 X01 08 ATEX 1113 X01 08 ATEX 1113 X01

II 2 G Ex db IIB T4 Gb Ex db IIB T4 Gb Ex db IIB T4 Gb Ex db IIB T4 Gb Ex db IIB T4 Gb Ex db IIB T4 Gb

P1 / P2 [kW] 1,0 / 0,8 1,8 / 1,5

2,7 / 2,1 3,5 / 2,65 2,4 / 1,9 3,5 / 2,65

U [V] 3/PE x 400 3/PE x 400

3/PE x 400 3/PE x 400 3/PE x 400 3/PE x 400

f [Hz] 50 50

50 50 50 50

I [A] 2,3 3,3

4,6 6,9 4,2 6,9

cos phi 0,60 0,78

0,85 0,74 0,83 0,74

n [min-1] 1440 1385

1375 1425 1395 1420

15/26 A1 25/26 A2 10/46 B1 15/46 B3 25/46 B4

[kg] 41 48 45 50 62

PN 6 /10 DN 65 DN 65 DN 80 DN 80 DN 80

[mm] 40 40 70 70 70

S2 25 min 22 min 40 min 15 min 15 min

S3* 40 % 35 % 45 % 25 % 25 %

Motor D 90-2/75 D D 90-2/110 C D 90-4/75 D D 90-4/75 D D 90-4/110 C

P1 / P2 [kW] 2,7 / 2,1 4,1 / 3,6 1,4 / 1,05 2,7 / 2,0 4,0 / 3,4

U [V] 3/PE x 460 3/PE x 460 3/PE x 460 3/PE x 460 3/PE x 460

f [Hz] 60 60 60 60 60

I [A] 4,1 6,1 2,7 4,0 6,6

cos phi 0,83 0,87 0,65 0,85 0,76

n [min-1] 3400 3400 1700 1700 1700

Leistungen • Performance • Puissances • Capaciteit • Prestazioni •

Wydajności i moce • Výkony • Výkony • Teljesítmény • Capacităţi

H [m] 1 2 3 4 5 6 7 8 9 10 12 14 16 18 20 22

10/2 A1 38 35 32 29 26 22 19 16 12 9 3

15/2 A1 50 49 46 43 40 37 35 32 28 25 18 11 5

25/2 A2 62 60 58 56 54 51 48 45 42 39 33 27 20 13

35/2 A2 70 68 67 66 64 63 61 58 56 53 48 43 37 30 24 13

25/2 B1 91 86 80 74 68 61 55 49 42 36 20 8

35/2 B2 126 121 117 111 103 96 89 81 72 65 49 31 16

10/4 B1 59 52 40 28 14 3

15/4 B3 98 90 80 70 58 46 35 20 12 6

25/4 B4 120 114 106 97 87 77 65 53 43 31 9

35/4 B4 132 125 119 112 104 95 85 74 64 53 30

25/4 C1 154 139 122 103 87 71 51 32 16

35/4 C1 170 160 146 133 119 101 89 71 54 36 3

UC 25/4 C1 104 87 71 51 32 16

UC 35/2 B2 102 95 88 80 72 65 17

UC 35/4 C1 103 89 72 54 36 3

15/26 A1 59 57 55 53 51 48 46 43 41 39 34 28 23 17 12 9

25/26 A2 76 75 74 72 70 68 66 64 62 60 55 50 43 39 34 29

10/46 B1 72 67 60 51 41 30 18 9

15/46 B3 118 112 105 97 88 78 68 59 49 40 21 8

25/46 B4 144 138 132 125 119 112 102 93 84 75 54 34 13

Q [m³ /h]

Ersatzteile - Spare parts - Pièces de rechange - Reserveonderdelen - Parti di ricambio - Reservedele - Reservdelar

Varaosat - Części zamienne - Náhradní díly - Alkatrészek - Piese de schimb - Запасные части -

备件

JUNG-PUMPEN.DE

MULTISTREAM 10 - 35

①Leitung Cable

10 M JP46259

EX, 10 M JP45469

EX, 15 M JP45583

EX, 20 M JP45584

②Schäkel Shackle

JP45904

③Stator + Gehäuse Stator + Housing

10/2, 15/2, 25/2 JP44008

35/2 JP46211

10/4, 15/4, 25/4 JP47042

35/4 JP47045

④Steckverbinder Connector

JP46572

⑤Lagersatz Bearing set

JP46214

⑥Rotorwelle Rotor shaft

10/2, 15/2, 25/2 JP47038

35/2 JP47039

10/4, 15/4, 25/4 JP47040

35/4 JP47041

⑦Lagerkammer Bearing housing

A1 JP47068

B1 JP47069

A2, B2 JP47070

B3, B4, C1 JP47071

⑧Wellenabdeckung Shaft cover

JP47043

⑨Laufradbefestigung Impeller xation

JP47059

⑩Laufrad Impeller

10/2 A1 JP47047

15/2 A1 JP47048

25/2 A2 JP47049

35/2 A2 JP47050

25/2 B1 JP47051

35/2 B2 JP47052

10/4 B1 JP47053

15/4 B3 JP47054

25/4 B4 JP47055

35/4 B4 JP47056

25/4 C1 JP47057

35/4 C1 JP47058

⑪Ölschraube Oil screw

JP46046

⑫Gleitringdichtung Mechanical seal

JP46567

⑬Dichtungssatz Seal set

JP47077

⑭Pumpengehäuse Pump casing

A1 JP47060

A2 JP47061

B1 JP47062

B2 JP47063

B3 JP47064

B4 JP47065

C1 JP47066

UC JP47067

⑮Schraubensatz Screw set

JP47076

⑯Schleißring Wear ring

B2 JP47072

B4 JP47073

C1 JP47074

⑰1l Öl 1l Oil JP48236

10x O-Ring 38x3,5

JP48109

b10x Splint / Cotter pins 1,6 x 20 JP46182

c10x

O-Ring 10x2,5

JP48088

0197

JUNG PUMPEN GmbH - Industriestr. 4-6 - 33803 Steinhagen, Germany

411.13.1612

EN 12050-1:2001

Fäkalienhebeanlage

10/2 A1 (JP09615/4)

10/4 B1 (JP09620/4)

15/2 A1 (JP09616/4)

15/4 B3 (JP09622/4)

25/2 A2 (JP09617/4)

25/2 B1 (JP09618/4)

25/4 B4 (JP09623/4)

25/4 C1 (JP09624/4)

35/2 A2 (JP09651/4)

35/2 B2 (JP09652/4)

35/4 B4 (JP09647/4)

35/4 C1 (JP09648/4)

10/2 A1, EX (JP09628/4)

10/4 B1, EX (JP09633/4)

15/2 A1, EX (JP09629/4)

15/4 B3, EX (JP09635/4)

25/2 A2, EX (JP09630/4)

25/2 B1, EX (JP09631/4)

25/4 B4, EX (JP09636/4)

25/4 C1, EX (JP09637/4)

35/2 A2, EX (JP09653/4)

35/2 B2, EX (JP09654/4)

35/4 B4, EX (JP09649/4)

35/4 C1, EX (JP09650/4)

Sammeln und automatisches Heben von fäkalienfreiem und

fäkalienhaltigem Abwasser über die Rückstauebene

BRANDVERHALTEN NPD

WASSERDICHTHEIT Bestanden

WIRKSAMKEIT (HEBEWIRKUNG)

- Förderung von Feststoffen Bestanden

- Rohranschlüsse Bestanden

- Mindestmaße von Lüftungsleitungen NPD

- Mindestießgeschwindigkeit Bestanden

- Freier Mindestdurchgang der Anlage Bestanden

- Mindestnutzvolumen NPD

MECHANISCHE FESTIGKEIT

- Tragfähigkeit und strukturelle Stabilität des Sammelbe-

hälters für die Verwendung außerhalb von Gebäuden

NPD

- Strukturelle Stabilität des Sammelbehälters für die Ver-

wendung innerhalb von Gebäuden

NPD

GERÄUSCHPEGEL ≤ 70 dB(A)

DAUERHAFTIGKEIT

- der Wasserdichtheit Bestanden

- der Hebewirkung Bestanden

- der mechanischen Festigkeit Bestanden

GEFÄHRLICHE SUBSTANZEN NPD

0197

JUNG PUMPEN GmbH - Industriestr. 4-6 - 33803 Steinhagen, Germany

411.13.1612

EN 12050-1:2001

Lifting plant for wastewater containing faecal matter

10/2 A1 (JP09615/4)

10/4 B1 (JP09620/4)

15/2 A1 (JP09616/4)

15/4 B3 (JP09622/4)

25/2 A2 (JP09617/4)

25/2 B1 (JP09618/4)

25/4 B4 (JP09623/4)

25/4 C1 (JP09624/4)

35/2 A2 (JP09651/4)

35/2 B2 (JP09652/4)

35/4 B4 (JP09647/4)

35/4 C1 (JP09648/4)

10/2 A1, EX (JP09628/4)

10/4 B1, EX (JP09633/4)

15/2 A1, EX (JP09629/4)

15/4 B3, EX (JP09635/4)

25/2 A2, EX (JP09630/4)

25/2 B1, EX (JP09631/4)

25/4 B4, EX (JP09636/4)

25/4 C1, EX (JP09637/4)

35/2 A2, EX (JP09653/4)

35/2 B2, EX (JP09654/4)

35/4 B4, EX (JP09649/4)

35/4 C1, EX (JP09650/4)

Collection and automatic lifting of wastewater without sewage and

wastewater containing faecal matters above the backow level

REACTION TO FIRE NPD

WATERTIGHTNESS Pass

EFFECTIVENESS (LIFTING EFFECTIVENESS)

- Pumping of solids Pass

- Pipe connections Pass

- Minimum dimensions of ventilating pipes system NPD

- Minimum ow velocity Pass

- Minimum free passage of the plant Pass

-Minimum useful volume NPD

MECHANICAL RESISTANCE

- Load bearing capacity and structural stability of collec-

tion tank for use outside buildings

NPD

- Structural stability of collection tank for use inside buil-

dings

NPD

NOISE LEVEL ≤ 70 dB(A)

DURABILITY

- of structural stability Pass

- of lifting effectiveness Pass

- of mechanical resistance Pass

DANGEROUS SUBSTANCES NPD

DEUTSCH ENGLISH

JUNG PUMPEN GmbH - Industriestr. 4-6 - 33803 Steinhagen - Germany -

www.jung-pumpen.de

DE - Wir erklären in alleiniger Verantwortung, dass das Produkt den aufgeführten Richtlinien entspricht.

CS - Prohlašujeme na svou výlučnou odpovědnost, že výrobek odpovídá jmenovaným směrnicím.

DA - Vi erklærer under ansvar at produktet i overensstemmelse med de retningslinjer

EN - We hereby declare, under our sole responsibility, that the product is in accordance with the specied Directives.

FI - Me vakuutamme omalla vastuullamme, että tuote täyttää ohjeita.

FR - Nous déclarons sous notre propre responsabilité que le produit répond aux directives.

HU - Kizárólagos felelősségünk tudatában kelentjük, hogy ez a termék megfelel az Európai Unió fentnevezett irányelveinek.

IT - Noi dichiariamo sotto la nostra esclusiva responsabilità che il prodotto è conforme alle direttive citate

NL - W verklaren geheel onder eigen verantwoordelkheid dat het product voldoet aan de gestelde richtlnen.

PL - Z pełną odpowiedzialnością oświadczamy, że produkt odpowiada postanowieniom wymienionych dyrektyw.

RO - Declarăm pe proprie răspundere că produsul corespunde normelor prevăzute de directivele mai sus menţionate.

SK - Na výlučnú zodpovednosť vyhlasujeme, že výrobok spíňa požiadavky uvedených smerníc.

SV - Vi försäkrar att produkten på vårt ansvar är utförd enligt gällande riktlinjer.

CE 311-16-1808

Steinhagen, 30-08-2018

______________________ i.V. ____________________

Stefan Sirges, General Manager Rüdiger Rokohl, Sales Manager

• 2006/42/EG (MD) EN 809:1998/AC:2010, EN ISO 12100:2010

• 2011/65/EU (RoHS)

• 2014/30/EU (EMC) EN 60034-1:2010, EN 61000-3-2:2014, EN 61000-3-3:2013

• 2014/34/EU (ATEX) EN 60079-0:2011/A11:2013, EN 60079-1:2014

DE - Richtlinien - Harmonisierte Normen

CS - Směrnice - Harmonizované normy

DA - Direktiv - Harmoniseret standard

EN - Directives - Harmonised standards

FI - Direktiivi - Yhdenmukaistettu standardi

FR - Directives -

Normes harmonisées

HU - Irányelve - Harmonizá szabványok

IT - Direttive - Norme armonizzate

NL - Richtlnen - Geharmoniseerde normen

PL - Dyrektywy - Normy zharmonizowane

RO - Directivă - Norme coroborate

SK - Smernice - Harmonizované normy

SV - Direktiv - Harmoniserade normer

10/2 A1, EX (JP09628/4)

10/4 B1, EX (JP09633/4)

15/2 A1, EX (JP09629/4)

15/4 B3, EX (JP09635/4)

25/2 A2, EX (JP09630/4)

25/2 B1, EX (JP09631/4)

25/4 B4, EX (JP09636/4)

25/4 C1, EX (JP09637/4)

35/2 A2, EX (JP09653/4)

35/2 B2, EX (JP09654/4)

35/4 B4, EX (JP09649/4)

35/4 C1, EX (JP09650/4)

10/2 AW1, EX (JP47280)

10/4 CW1, EX (JP09609/5)

15/2 AW1, EX (JP47278)

15/4 AW2, EX (JP46792)

15/4 BW1, EX (JP09458/1)

15/4 CW1, EX (JP09611/5)

25/2 AW1, EX (JP09150/4)

25/2 AW1, EX (JP46123)

25/2 AW1, EX (JP46124)

25/2 AW1, EX (JP46119)

25/2 AW1, EX (JP47213)

25/2 AW1, EX (JP46120)

25/2 AW1, EX (JP09272)

25/2 BW1, EX (JP09499/1)

25/4 AW2, EX (JP46867)

25/4 BW1, EX (JP09459/1)

25/4 CW1, EX (JP09656/5)

35/2 AW1, EX (JP09152/4)

35/2 BW1, EX (JP09501/1)

35/4 AW2, EX (JP46868)

35/4 BW1, EX (JP09460/1)

35/4 CW1, EX (JP09859/5)

45/2 AW1, EX (JP46870)

45/2 BW1, EX (JP46857)

45/2 CW1, EX (JP47353)

45/4 AW2, EX (JP46869)

45/4 BW2, EX (JP46859)

45/4 CW2, EX (JP47237)

25/2 ME, EX (JP09742/4)

35/2 M, EX (JP09807/5)

36/2 M, EX (JP09908/4)

45/2 M, EX (JP09431)

35/2 M Tan, EX (JP09179/3)

36/2 M Tan, EX (JP09180/3)

45/2 M Tan, EX (JP48306)

II 2 G Ex db IIB T4 Gb PTB 08 ATEX 1113 X 01

Physikalisch-Technische Bundesanstalt

Zertizierungssektor Explosionsschutz (0102)

Bundesallee 100 - 38116 Braunschweig - Germany

EU-Konformitätserklärung

EU-Prohlášeni o shodě

EU-Overensstemmelseserklæring

EU-Declaration of Conformity

EU-Vaatimustenmukaisuusvakuutus

EU-Déclaration de Conformité

EU-Megfelelöségi nyilatkozat

EU-Dichiarazione di conformità

EU-Conformiteitsverklaring

EU-Deklaracja zgodności

EU-Declaraţie de conformitate

EU-Vyhlásenie o zhode

EU-Försäkran om överensstämmelse

DE - Weitere normative Dokumente CS - Jinými normativními dokumenty DA - Andre nor-

mative dokumenter EN - Other normative documents FI - Muiden normien FR - Autres

documents normatifs HU - Egyéb szabályozó dokumentumokban leírtaknak IT - Altri docu-

menti normativi NL - Verdere normatieve documenten PL - Innymi dokumentami normaty-

wnymi RO - Alte acte normative SK - Iným záväzným dokumentom SV - Vidare normerande

dokument:

EN 60034-5:2001/A1:2007

EN 60079-14:2007

DE - Bevollmächtigter für technische Dokumentation CS - Oprávněná osoba pro tech-

nickou dokumentaci DA - Autoriseret person for teknisk dokumentation EN - Au-

thorized person for technical documentation FI - Valtuutettu henkilö tekninen do-

kumentaatio FR - Personne autorisée à la documentation technique HU - Hivatalos

személy műszaki dokumentáció IT - Persona abilitata per la documentazione tecnica

NL - Bevoegd persoon voor technische documentatie PL - Pełnomocnik ds. dokumentacji

technicznej RO - Persoană autorizată pentru documentatiei tehnice SK - Oprávnená osoba

pre technickú dokumentáciu SV - Auktoriserad person för teknisk dokumentation:

JUNG PUMPEN - Stefan Sirges - Industriestr. 4-6 - 33803 Steinhagen