Pentair IntelliTouch520366 Instruction manual

Rev. B 3-19-04 1 P/N 520366
Pentair Pool Products Quick Start Guide
IntelliTouch™Quick-Start Manual
Set-Up and Programming
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
PentairPoolProducts
1620 Hawkins Ave., Sanford, NC 27330 • [phone]
10951 West Los Angeles Ave., Moorpark, CA 93021 • [phone]
Important Notice
Attention Installer.
This manual contains important information about the installation, operation and safe use of this
product. This information should be given to the owner/operator of this equipment.
Before installing this product, read and follow all warning notices and instructions which are included. Failure to
follow safety warnings and instructions can result in severe injury, death, or property damage.
Call [phone] for additional free copies of these instructions.
WARNING

P/N 520366 2 Rev. B 3-19-04
Quick Start Guide Pentair Pool Products

Rev. B 3-19-04 3 P/N 520366
Pentair Pool Products Quick Start Guide
System Requirements
This Quick Start helps you test and set up the IntelliTouch system. Use these instructions to
make sure the system is working and properly set up for the homeowner.
This Quick Start is for the following systems:
•Wired only systems. If you are using a MobileTouch, this Quick Start is not for you.
•Only 1 expansion center. If you have multiple centers, this Quick Start is not for you.
•Only 1 iS10 OR multiple iS10s configured to the same circuits.
CAUTION
DO NOT OPERATE ANY OF THESE CONTROLS BEFORE READING THESE INSTRUCTIONS.
You can fold the Outdoor Control Panel downward to get to the rear circuit board while
operating. In the unlikely event you need to plug in any low voltage devices, you must feed a
cable up the Low Voltage Raceway on the left.Turn the power off and remove the High
Voltage Cover Panel to make it easier to feed the cable.
In this Quick Start
System Requirements .................................................................................................................... 3
Before You Start .............................................................................................................................. 4
Check the Load Center ................................................................................................................... 5
Setting up the Indoor Control Panel .............................................................................................6
Testing the Indoor Control Panel ...................................................................................................................... 6
Setting the Clock ..................................................................................................................................................... 6
Setting the Circuit Names .................................................................................................................................... 7
Assigning Circuit Functions and Freeze Protection .................................................................................... 8
Setting up Additional Equipment ................................................................................................................... 10
Configuring Spa-side Controls ......................................................................................................................... 12
Programming Timed Circuits ............................................................................................................................ 13
Other Available Equipment ..........................................................................................................13
Notes .............................................................................................................................................14

P/N 520366 4 Rev. B 3-19-04
Quick Start Guide Pentair Pool Products
Important Notice
This equipment has been tested and found to comply with the limits for a Class B digital
device,pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable
protection against harmful interference in a residential installation.This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the party responsible for FCC compliance could
void the users authority to operate the equipment.
BeforeYou Start
If you have more than 1 Indoor Control panel, you only need to configure 1 panel. Other
Indoor Control panels will read that programming and use it.
Before you start, make sure you have:
•Pen and paper
•Marker or other way to label the circuits. Use the provided Circuit ID label sheet, a
permanent marker, or other permanent means of labeling.
•If the system you are setting up is large or covers a large area, get an assistant to walk
the property while you test the circuits
Setting up the IntelliTouch involves the steps detailed in the guide. Follow the steps in order
to make sure the IntelliTouch is properly set up and working correctly.

Rev. B 3-19-04 5 P/N 520366
Pentair Pool Products Quick Start Guide
Check the Load Center
1. Turn on the electrical power at the house
breaker.
2. Turn on the Load Center.You may need to turn
on the breakers on the Load Center.
3. Wait for the following:
· In the System Control lights area, only one
light is on, usually the Auto light.
· The light labeled See Indoor Control
Panel if Flashing stops flashing.
4. Press the Service button to put the Load Center
in Service Mode for testing.
Note: If you are working with the i5, i7+3, or
i9+3 systems, go to step 5. If you are working
with the i5S, i9+3S, or i10+3D systems, skip step
5 and go to step 6.
5. Press the Valves button.Step thru all 4 valve
positions: Pool, Spa, Fill, Drain. Make sure the
valves turn on correctly and the water is moving
in the correct direction for each position.
6. Press the Filter Pump button. Make sure the
filter pump turns on correctly.If the pump has 2
speeds: Press the button 1 time to run the pump
in low speed. Press the button again to run the
pump in high speed. Press the button again to
turn the pump off.
7. Step through the rest of the system control
buttons. Notice which button turns on which
equipment.You may need to walk the property
to find what each button turns on.
8. Write down what each button turns on,
including the number of the circuit.
9. Label the circuit buttons on the outdoor control
panel.You need this information when you set
up the Indoor Control Panel.
When you are done, you are ready to set up the
Indoor Control Panel. See the next section.

P/N 520366 6 Rev. B 3-19-04
Quick Start Guide Pentair Pool Products
Setting up the Indoor Control Panel
The Indoor Control panel looks like the
following picture.
Select items on the screen by pressing the
buttons on each side and the bottom.
Testing the Indoor Control Panel
Press the button in the upper left labeled
either Spa or Hi-Temp, depending on the
model of Indoor Control Panel. An LED turns
on.
If none of the LEDs turn on, you have a
problem.Contact Technical Service for help
at 800-831-7133.
Setting the Clock
Setting the clock lets all automatic pool functions work correctly.
MENU SETUP CLOCK
Getting There
Go to the Clock screen.
1. Using the buttons on either side of the
panel, set the time and date.
2. Specify the Daylight savings setting.
If you are in an area that observes
Daylight savings, set this to Auto. If
you are in an area that does not
observe daylight savings, set this to
Manual.
3. When you are done, press the Save
button.
4. Press the Exit button to return to the Main screen.
A

Rev. B 3-19-04 7 P/N 520366
Pentair Pool Products Quick Start Guide
Setting the Circuit Names
Setting the circuit names lets the homeowner use the pool equipment from the Indoor Control
Panel. Many common equipment names are already programmed into the Indoor Control
Panel. If you need to program custom circuit names, refer to the IntelliTouch Setup manual.
MENU SETUP CIRCUIT NAMES ASSIGN CIRCUIT NAMES DISPLAYADVANCED
Getting There
Go to the Assign Circuit Display screen.
1. Get the written list of circuit names you made while setting up the Load Center.Find
what you labeled circuit button 1.The circuit names you assign must match the labels
you put on the Load Center.
2. On the Assign Circuit Display screen,
press the button next to the label AUX
1.You see a small arrow pointing to
the name of that label.
3. Use the Up and Down buttons at the
bottom of the screen to walk through
the alphabetical list of programmed
names.
4. When you find the name you want,
press the button next to the label AUX
2.The small arrow moves to that label.
You are done setting the first circuit
name and are ready to program the
next circuit.
5. Continue the process to assign the
other circuits. Depending on the
model you are programming, you may
not have equipment for all circuits.
6. When you are done assigning names,
press the Save button.
7. Press the Exit button to return to the
Main screen.

P/N 520366 8 Rev. B 3-19-04
Quick Start Guide Pentair Pool Products
Assigning Circuit Functions and Freeze Protection
Assigning circuit functions lets you set special logic to a circuit. For example, you can set up an
automatic pool cleaner to only run if the filter pump is on.Further,the automatic cleaner pump
will turn off when the spa and/or solar is turned on.
Freeze protection turns on a circuit if the air temperature drops below 35° F.This is especially
important if there is a pool and spa combination. If freeze protection is set to both the spa
and pool circuits, the filter pump comes on and the pool and spa valves alternate every 15
minutes to keep the water moving in both until the freeze condition is over.
MENU SETUP ADVANCED CIRCUIT FUNCTIONS SELECT DESIRED CIRCUIT
SELECT DESIRED SCREEN
DISPLAY 1,2,3,4 or F
This Button appears only
when you have FEATURE
circuits or multiple DISPLAYS.
Getting There
To set the pool and spa freeze protection
1. Use the Getting There picture above.
When you get to the Select screen,
press Pool.
2. Find the No label. Press the button
next to it to change the setting to Yes.
3. When you are done, press Save.
4. Press the Back button to return to the
Circuits screen.
5. Press the button next to the label Spa,
if there is a spa.
6. Find the No label. Press the button
next to it to change the setting to Yes.
7. When you are done, press Save.
8. Press the Back button to return to the Circuits screen.
9. Repeat the above steps for any other circuits that you want to assign freeze protection.

Rev. B 3-19-04 9 P/N 520366
Pentair Pool Products Quick Start Guide
To assign other logic to a circuit
1. Go to the Circuit Functions screen and select a circuit to assign special logic.
Note: You must set pressure cleaners to Master Cleaner circuit function.
2. Press the Prev or Next buttons to make your selections.The options are:
3. When you are done, press Save.
4. Press the Exit button to return to the Main screen.
Generic No special Logic. Simple On/Off control of a circuit with all the
programmable capabilities.
Master cleaner Works with automatic pool cleaner pumps or cleaner valve actuator. It
oes the following:
- Forces the filter pump on 5 minutes before the cleaner.
- Turns the cleaner off when the spa is on.
- Turns the cleaner off for 5 minutes when the solar heating begins.
Light Allows special lighting features to work, such as ALL lights on or ALL
lights off.
Dimmer Allows light imming features to work. Dimming relay must be
installe .
SAM Light Activates special color lighting programs on other screens on the
In oor Control Panel when use with SAM pool lights. For example,
you can have ALL lights on or ALL lights off, or use Color Swim, Color
Set, or Color Synch.
SAL Light Activates special color lighting programs on other screens on the
In oor Control Panel when use with SAL spa lights. For example, you
can have ALL lights on or ALL lights off, or use Color Swim, Color Set,
or Color Synch.
Photon Generator Lets Pentair Fiberworks fiber optic bulb be operate by Color Set or
Color Swim programs when use with SAM an SAL lighting.
Color Wheel Activates special color lighting programs on other screens on the
In oor Control Panel when use with Pentair Fiberworks. For
example, you can have ALL lights on or ALL lights off, or use Color
Swim, Color Synch, or Color Set.
Valve Not currently use .
Spillway For pool/spa combinations where the spa is raise above the pool.
This setting moves the return valve so that the filter pump pulls the
water from the pool an returns it to the spa, creating a water fall
effect. Automatic pool cleaners are turne off when this feature is
turne on.
Floor Cleaner This setting moves a 3-way valve every 20 minutes alternating flow
between 2 cleaner system valves that fee the pop-up hea s.

P/N 520366 10 Rev. B 3-19-04
Quick Start Guide Pentair Pool Products
Setting up Additional Equipment
If any special equipment is attached, you need to set that up now.You may or may not have
this equipment.
This section explains setting up the following:
•Solar or heat pump equipment - Lets you set solar or heat-pump heaters to work.
•2 speed pump - Lets you set circuits that switch the filter pump to high speed.
•Cool-down cycle for the heater - Lets you set a cool-down cycle for heaters that need it.
•Automatic spa heating when the spa is manually turned on - Heats the spa using the
Spa button on the Indoor Control panel or the spa-side control, even when the heater is
set to OFF in the Heat screen.This lets the homeowner heat the spa on-demand. Timed
programs will not heat the spa.
To set up the solar equipment
MENU SETUP EQUIPMENT SOLAR
Getting There
Go to the Solar screen.
1. Press the button next to the Water
Solar Present label to change it to Yes.
2. If a heat pump is being used instead
of a solar heating system, press the
second button to change it to Yes.
3. When you are done, press the Save
button.
4. Press the Exit button to return to the
Main screen.
To set up a 2 speed pump
MENU SETUP EQUIPMENT 2-SPEED PMP
Getting There
Go to the 2 Speed Pump screen.
1. Press the button next to a None label.
You see a small arrow pointing to the
name of that label.