Pentair US-1500 User manual

US1500 MONITORED DUAL FILTRATION SYSTEM
INSTALLATION AND OPERATING INSTRUCTIONS
©2018 Pentair Residential Filtration, LLC waterpurification.pentair.com

SPECIFICATIONS
Temperature Range: 40–100°F (4.4–37.8°C)
Pressure Range: 30–125 psi (2.1–8.62 bar)
Service Flow Rate
@ 60 psi (4.1 bar): 0.5 gpm (1.9 L/min)
Rated Service Life: 1,000 gallons (3,785L)
Dimensions: 9.18 x 4.70 x 12.72 inch
(233 mm x 119 mm x 323 mm)
Weight: 6 lbs. (2.7 kg) (filled with water)
PARTS INCLUDED
• Filter system with filter cartridges – P-250 Cartridge Set
• Installation hardware
(mounting screws, T-Adapter, quick-connect elbows)
• Electronic monitor and 9-volt battery
• Housing wrench
• Lead-free drinking water faucet
• 1/4-inch plastic tubing
TOOLS AND MATERIALS REQUIRED
• Safety glasses
• Hand or electric drill (cordless recommended)
• 1/4-inch drill bit
• File
• Phillips head screwdriver
• Adjustable wrench or 7/16-inch open-end wrench
• Tube cutters or utility knife if sink does not have hole for
separate faucet
• Center punch
• 3/4-inch drill bit or hole saw
PRECAUTIONS
WARNING:
Do not use with water that is microbiologically
unsafe or of unknown quality without adequate
disinfection before or after the system.
Systems certified for cyst reduction may be
used on disinfected waters that may contain
filterable cysts.
CAUTION
Filter must be protected against freezing, which
can cause cracking of the filter and water leakage.
CAUTION
The rubber o-ring provides the water-tight seal
between the cap and the bottom of the housing. It
is important that the o-ring be properly seated in
the groove below the threads of the housing or a
water leak could occur.
CAUTION
Because of the product’s limited service life and to
prevent costly repairs or possible water damage,
we strongly recommend that the bottom of all
plastic housings be replaced every ten years. If the
bottom of your housing has been in use for longer
than this period, it should be replaced immediately.
Date the bottom of any new or replacement
housing to indicate the next recommended
replacement date.
NOTE:
• For cold water use only.
• Make certain that installation complies with all state
and local laws and regulations.
• The contaminants or other substances removed or
reduced by the selected cartridge are not necessarily in
your water. Ask your local water municipality for a copy
of their water analysis, or have your water tested by a
reputable water testing lab.
• After prolonged periods of non-use (such as during a
vacation) it is recommended that the system be flushed
thoroughly. Let water run for 5–6 minutes before using.
• The filter cartridges used with this system have a
limited service life. Changes in taste, odor, and/or flow
of the water being filtered indicate that the cartridge
should be replaced.
ABOUT YOUR PENTAIR DUAL FILTRATION
SYSTEM
Thank you for purchasing a Pentair Dual Filtration System.
With only minimal maintenance, your new system will provide
you with safer, better-tasting water for years to come. The
filter cartridges should be changed after every 1,000 gallons
of use or once every twelve months, whichever comes first.
Filter life will vary depending on usage and water conditions.
Changes in taste, odor, and/or flow of the water being filtered
indicate that the filter cartridges should be replaced.
The Model US-1500 is Tested and Certified by NSF
International against NSF/ANSI Standard 53 for the
reduction of Lead and VOC.
2• PENTAIR US-1500 Monitored Dual Filtration System Installation and Operating Instructions

INSTALLATION
• For standard under-sink installation on 1/2-inch 14 NPS
threads (most common thread on kitchen faucets) cold
water line.
• Please read all instructions and precautions before
installing and using your dual filtration system.
• Numbered diagrams correspond with numbered steps.
1. Installing the Water Supply Adapter
The supply adapter fits 1/2-inch 14 NPS supply threads. If local
codes permit, it may be used to connect the US-1500 to the
cold water supply line. If local codes do not permit the use of
the supply adapter, alternate connectors can be obtained from
your local supplier.
A. Turn off cold water supply line. If cold water line does not
have a shut-off valve under the sink, you should install one.
B. Turn on the cold water faucet and allow all water to drain
from line.
C. Disconnect cold water line from 1/2-inch 14 NPS threaded
stub on bottom of main faucet.
D. Apply plumber tape onto threads of faucet stub and supply
adapter. Screw the water supply adapter to the threaded
faucet stub as shown.
E. Using the nut that previously connected the cold water line
to the faucet, screw the cold water line to the male supply
adapter threads.
2. Selecting the Faucet Location
NOTE: The drinking water faucet should be positioned with
function, convenience, and appearance in mind. An
adequate flat area is required to allow faucet base to
rest securely. The faucet fits through a 3/4 inch hole.
Most sinks have pre-drilled 1-3⁄8 inch or 1-1⁄2 inch
diameter holes that may be used for faucet installation.
If these pre-drilled holes cannot be used or are in an
inconvenient location, it will be necessary to drill a 3/4
inch hole in the sink to accommodate the faucet.
CAUTION
This procedure may generate dusts which can
cause severe irritation if inhaled or come in contact
with the eyes. The use of safety glasses and
respirator for this procedure is recommended.
CAUTION
Do not attempt to drill through an all-porcelain
sink. If you have an all-porcelain sink, mount the
faucet in pre-drilled sprayer hole or drill through
countertop next to sink.
CAUTION
When drilling through a countertop make sure the
area below the drilled area is free of wiring and
piping. Make certain that you have ample room to
make the proper connections to the bottom of
the faucet.
CAUTION
Do not drill through a countertop that is more than
1 inch thick.
CAUTION
Do not attempt to drill through a tiled, marble,
granite or similar countertop. Consult a plumber
or the countertop manufacturer for advice
or assistance.
A. Line bottom of sink with newspaper to prevent metal
shavings, parts, or tools from falling down drain.
B. Place masking tape over the area to be drilled to prevent
scratches if drill bit slips.
C. Mark hole with center punch. Use a 1/4-inch drill bit for a
pilot hole, then, using a 3/4-inch drill bit or hole saw, drill
a hole completely through the sink. Smooth rough edges
with a file.
2
A
B
C
1
A
B
C
D
E
PENTAIR US-1500 Monitored Dual Filtration System Installation and Operating Instructions • 3

3. Mounting the Faucet
A. Remove wing nut and metal washer from the threaded
shaft of the faucet. Leave the black rubber washer on the
threaded shaft.
B. Slide the threaded shaft of the faucet into drilled hole.
C. From under the sink, slide the metal washer on and thread
on the wing nut. Tighten the wing nut by hand until tight.
It may be necessary to have a second person to hold the
faucet while tightening the wing nut.
NOTE: Do not overtighten the wing nut. Hand tighten only.
Do not use pliers or wrench to tighten.
4. Mounting the System
A. Center system between water supply adapter and drinking
water faucet.
NOTE: Allow 1-1⁄2 inch (38 mm) clearance below system for
changing filter cartridges.
B. Install mounting screws at least 13-3⁄4 inch (350 mm) from
cabinet floor and 4-1⁄8 inch (124 mm) apart. Leave enough
space (approximately 1/2 inch [13 mm]) between the head
of the screw and the wall to slip system onto screws.
C. Place system over screws on wall and slide downwards to
lock into place. Make certain system is firmly attached to
wall to prevent it from falling and possibly being damaged.
5. Connecting the Faucet
A. Insert one end of the 1/4-inch tube, supplied in the
installation kit, into the gray quick-connect fitting collar
located on the bottom of the threaded shaft of the faucet.
Push tubing into the fitting until you come to a hard stop.
CAUTION
Do not bend or crimp tube when inserting.
B. Gently pull back on the tube to ensure it is connected
properly. If the tube comes out of fitting, cut a small section
of the tube off and reconnect.
6. Connecting the Supply Adapter and Inlet of
Filter
A. Determine the length of plastic tubing needed to connect
the inlet (left) side of the filter with the supply adapter. Be
sure to allow enough tubing to prevent kinking and cut the
tubing squarely. Place a mark 5/8 inch from the end of the
tubing.
B. Wet tubing with water and insert into supply adapter 5/8
inches until mark is flush with fitting.
NOTE: Disconnecting the Tubing from the
Quick-Connect Fittings.
Routine maintenance and cartridge replacement will not
require that you disconnect the tubing from the filter system;
however, tubing may be quickly and easily removed from
the fitting if necessary. First, turn off the water supply to the
filter. Open faucet, then press in the grey collar around the
fitting while pulling the tubing with your other hand.
5
1-1⁄2 inch (38mm)
13-3⁄4 Inch
(350mm)
4
A
B
C
3
Black
Rubber
Washer
Wing
Nut
Metal
Washer
5/8 inch
(16mm)
6
5/8 inch
(16mm)
A
B
4• PENTAIR US-1500 Monitored Dual Filtration System Installation and Operating Instructions

7. Connecting the System
A. Assemble tubing with system as shown in Fig. 7, inserting
tubing into appropriate inlet or outlet quick-connect fitting
until it stops.
NOTE: In some installations, connecting the system to the
water supply adapter and/or drinking water faucet
causes the tubing to enter the quick-connect fitting
at a sharp angle. This may exert pressure on the
quick-connect fitting and cause it to leak. In these
situations, you may wish to use one or both of the
quick-connect elbows included with the installation
kit. Simply push the quick-connect elbow directly into
the quick-connect fitting on the system, then insert
the tubing into the quick-connect elbow.
B. When cut between a set of black guide arrows, the tubing
should be pushed into the fitting so that the entrance
of the fitting falls between the next set of guide arrows
(approximately 5/8 inch [16 mm]).
8. Installing the Battery
A. Remove cover on top of system. Attach 9-volt battery
(included) to connector, then place battery in holder
located to the left of the monitor panel as shown (Fig. 8).
B. Replace cover on top of system. Using a pen or pencil,
press and release the blue reset button on the front of the
system. The electronic monitor should beep twice. If the
monitor has been reset properly, the two beeps will be
followed by a sequence of two green, two yellow, and two
red lights. The monitor should be reset whenever a new set
of filter cartridges is installed.
9. Putting the System into Operation
A. Slowly turn on cold water supply.
B. Shut off faucet opened before starting installation.
C. Open water supply adapter.
D. Rotate base of drinking water faucet counter-clockwise to
“ON” position. Allow water to run for 5 minutes to flush air
and carbon fines from filter cartridges. Check system for
leaks before leaving installation.
INSTALLATION IS NOW COMPLETE.
7
8A
9
A
B
C
D
PENTAIR US-1500 Monitored Dual Filtration System Installation and Operating Instructions • 5

ELECTRONIC MONITOR OPERATIONS
The US-1500 system includes an electronic monitor that alerts
you when it is time to change your filter cartridges. Both filter
cartridges should be changed at the same time to ensure that
the monitor works properly. The monitor measures actual
water usage and is powered by a single 9-volt battery.
How the Electronic Monitor Works
The filter cartridges in the US-1500 should be replaced every
1,000 gallons. The electronic monitor uses a combination of
lights and alarms to alert you at different stages during the life
of the filter cartridges. The lights are visible on the front panel
of the filter system, to the left of the blue reset button:
0-950 gallons
No alarm. Green light flashes when water is turned on.
950-1000 gallons
Alarm BEEPS ONCE when water is turned on. Yellow light
flashes when water is on.
1000+ gallons
Alarm BEEPS TWICE when water is turned on. Red light
flashes when water is on.
Low or Dead Battery
No alarm. No lights. Replace battery.
NOTE: Gallons used while battery is dead will register on
meter when battery is replaced
NOTE: To extend battery life, any sequence that includes any
beeps will not be repeated if water is turned on again
in less than 15 minutes.
Reset Button
The blue reset button is located on the front panel of the
system. This button should only be pressed during initial
installation or when new filter cartridges are installed. After
pressing and releasing the button, you will hear two beeps
followed by a sequence of two green, two yellow, and two red
lights. This combination of beeps and lights indicates that the
system has properly reset the internal gallon counter.
REPLACING THE BATTERY
The battery should be replaced every time new filter cartridges
are installed or after 12 months of operation, whichever
comes first.
Replacing Battery and Filters at the Same Time:
Install new 9-volt battery as described in Step Eight: Installing
the Battery on p. 5. Make sure to press blue reset button on
front panel of system when finished.
Replacing Battery Only:
Remove the old battery and install the new battery. DO NOT
press the reset button on the front panel of the system
when finished.
FILTER CARTRIDGE REPLACEMENT
• Filter cartridges the US-1500 will last about 1,000 gallons
or twelve months before they need to be replaced. Filter
cartridge life varies depending on usage, and/or water
conditions. Changes in taste, color, and flow of the water
being filtered indicate that the cartridge should be replaced.
• Read all instructions before replacing filter cartridges.
1. Turn off cold water supply and open the drinking water
faucet to release pressure from system.
2. Unscrew and remove bottom of filter housing. Locate and
remove large o-ring, wipe clean of lubricant, and set aside.
Repeat for second housing.
3. Discard used filter cartridges. Using a non-abrasive sponge
or cloth, scrub the bottom of filter housings, o-ring grooves,
and caps with dish soap and warm water. Rinse thoroughly.
Fill bottom of each housing 1/3 full with water. Add 1
tablespoon of household bleach and scrub to disinfect.
4. Lubricate o-rings with silicone grease. Insert each o-ring
in groove and press into place.
NOTE: This step is important to ensure a proper housing
seal. Make certain each o-ring is seated level in its
groove or a leak may occur.
5. Screw bottom of housings with bleach water onto caps
without filter cartridges and hand-tighten. DO NOT
OVERTIGHTEN.
6. Turn on water supply. Let faucet run for about 10 seconds,
then turn off faucet and let stand for 20-30 minutes.
7. Turn on faucet and allow bleach water to run out
(about 3-5 minutes).
8. Turn off water supply to system and open faucet to release
pressure. Remove bottom of housings and empty of water.
9. Insert each filter cartridge in bottom of appropriate filter
housing: P-250 Cartridge Set: white with green end caps in
left housing, gray plastic cartridge in right housing.
NOTE: The filter cartridges should be installed with the
black gasketed ends pointing up.
10. Screw bottom of housings onto caps and hand-tighten. DO
NOT OVERTIGHTEN. Make certain cap standpipe slips
into cartridge.
11. Open water supply and turn on drinking water faucet to
release pressure in system. Let faucet run for 5 minutes
to remove trapped air and carbon fines. Check system for
leaks before leaving installation.
NOTE: It is recommended that you run the tap at least 20
seconds prior to using water for drinking or
cooking purposes.
NOTE: Initially, filtered water may appear cloudy. If you set a
glass of water on a level surface, you should be able to
watch the cloudiness disappear from the bottom of the
glass upwards. This harmless cloudiness results from
the release of trapped air within the cartridge and will
disappear within a few weeks after installation.
6• PENTAIR US-1500 Monitored Dual Filtration System Installation and Operating Instructions

TROUBLESHOOTING
Leaks:
...between cap and bottom of filter housing
Turn off water supply valve and turn on drinking water faucet
to release pressure in system. Remove bottom of housing.
Clean o-ring and o-ring groove (located directly beneath
threads of housing). Lubricate o-ring with silicone grease and
replace securely into groove. Screw bottom of housing onto
cap and hand-tighten. DO NOT OVER-TIGHTEN. Turn on water
supply valve and check for leaks.
...on system inlet/outlet connections
Turn off water supply valve and turn on drinking water faucet
to release pressure in system. Remove tubing from fitting
(see NOTE under Step Six: Connecting the Supply Adapter on
p.4) and make sure end of tubing is cut squarely and free of
scratches or burrs. Reinsert tubing into quick-connect fittings,
making sure to push securely until tubing hits a hard stop.
Turn on water supply valve and check for leaks.
...on supply adapter connection
Turn off water supply valve and turn on drinking water faucet
to release pressure in system. Loosen leaking threaded fitting
on supply adapter or pull out leaking tubing from fitting.
Inspect to see if plastic tubing is scratched or supply adapter
was properly attached. If tubing is scratched, cut off 1/2 inch
to 5/8 inch and reinstall per Step Six: Connecting the Supply
Adapter. Reconnect tubing or tighten compression nut with
fingers, then tighten nut snugly 1/2-turn with wrench. Turn on
water supply valve and check for leaks.
...on faucet/tubing connection
Turn off water supply valve and turn on drinking water
faucet to release pressure in system. Loosen and remove
compression nut fitting on faucet stem. Make sure tubing
is inserted firmly into end of faucet stem, then retighten
compression nut with fingers until secure then tighten 1 turn
with a wrench. Turn on water supply valve, then turn off faucet
to check for leaks.
NOTE: If leaks persist, or if there are other leaks on system,
turn off water supply. Call our technical support
department at 800.279.9404.
Low Water Flow
1. Check flow at faucet. The US-1500 system should fill a
gallon jug in approximately 2 minutes. Flow rates will vary
with individual household water pressure.
2. Check filter cartridge installation. Make certain both filter
cartridges are properly oriented in filter housings (See
Filter Cartridge Replacement).
3. Check to be certain that the water supply valve is
completely open (turn handle on valve counter-clockwise
as far as it will go).
4. Check flow through empty system. To do this, turn off
water supply valve and turn on drinking water faucet to
release pressure in system. Then remove filter cartridges
from housings and screw housings back onto caps. Turn on
faucet to check flow through empty system. Flow should be
about one to two gallons per minute. If flow is less than 0.4
gallons per minute, call Technical Support at 800.279.9404.
5. If flow through empty system is adequate, place one filter
cartridge in system at a time and check flow to make sure
cartridge is not clogged. Replace clogged cartridge
if necessary.
REPLACEMENT PARTS
1 155584-44 P-250 (Cartridges sold only as a set)
2 153126 White housing
3 151231 O-ring (OR-233)
4 244960 * Lead-Free Faucet
5 143431 Water Supply Adapter
6 150424 Housing Wrench (SW-5)
7 144721 Circuit and Probe (Not Shown)
*image may be different than actual faucet
For replacement parts, contact your nearest Pentair
distributor or call 800.279.9404.
2
3
46
1
5
PENTAIR US-1500 Monitored Dual Filtration System Installation and Operating Instructions • 7

PERFORMANCE DATA
Important Notice: Read this performance data and compare
the capabilities of this system with your actual water
treatment needs. It is recommended that, before installing a
water treatment system, you have your water supply tested to
determine your actual water treatment needs.
This system has been tested according to NSF/ANSI 53 for
reduction of the substances listed below. The concentration
of the indicated substances in water entering the system
was reduced to a concentration less than or equal to the
permissible limit for water leaving the system, as specified in
NSF/ANSI 53.
Model US-1500
Substance
Influent
Challenge
Concentration
Maximum
Permissible
Product Water
Concentration
Reduction
Requirements
Minimum
Reduction
Average
Reduction
Standard 53
Lead (pH 6.5) 0.15 mg/L ±
10% 0.010 mg/L 99.3% 98.7%
Lead (pH 8.5) 0.15 mg/L ±
10% 0.010 mg/L 99.4% 98.3%
Chloroform
(VOC surrogate
chemical)
0.300 mg/L ±
10% 0.015 mg/L 97.6% 99.7%
Flow Rate=0.5 gpm (1.9 L/min); Capacity=1000 gallons (3785 L) or 12 months
Testing was performed under standard laboratory conditions, actual performance may vary.
WARNING:
Do not use with water that is microbiologically
unsafe or of unknown quality without adequate
disinfection before or after the system.
Systems certified for cyst reduction may be
used on disinfected waters that may contain
filterable cysts.
NOTE: Substances reduced are not necessarily in your
water. Filter must be maintained according to
manufacturer’s instructions, including replacement
of filter cartridges.
Test Conditions
Flow Rate = as noted for filter system
Inlet Pressure = 60 psi (4.1 bar)
pH = 7.5±1
Temperature = 68°F ± 5°F (20°C ± 2.5°C)
Operating Requirements
Pressure = 30-125 psi (2.1–8.62 bar)
Temperature = 40-100°F (4.4–37.8°C)
Organic Chemicals Included by Surrogate Testing:
Substance
Influent Challenge
Concentration mg/L
Maximum permissible
product water
concentration mg/L
alachor 0.050 0.001
atrazine 0.100 0.003
benzene 0.081 0.001
carbofuran 0.190 0.001
carbon tetrachloride 0.078 0.0018
chlorobenzene 0.077 0.001
chloropicrin 0.015 0.0002
2,4-D 0.110 0.0017
dibromochloropropane (DBCP) 0.052 0.00002
o-dichlorobenzene 0.080 0.001
p-dichlorobenzene 0.040 0.001
1,2-dichloroethane 0.088 0.0048
1,1-dichloroethylene 0.083 0.001
cis-1,2-dichloroethylene 0.170 0.0005
trans-1,2-dichloroethylene 0.086 0.001
1,2-dichloropropane 0.080 0.001
cis-1,3-dichloropropylene 0.079 0.001
dinoseb 0.170 0.0002
endrin 0.053 0.00059
ethylbenzene 0.088 0.001
ethylene dibromide (EDB) 0.044 0.00002
haloacetonitriles (HAN):
bromochloroacetonitrile 0.022 0.0005
dibromoacetonitrile 0.024 0.0006
dichloroacetonitrile 0.0096 0.0002
trichloracetonitrile 0.015 0.0003
haloketones (HK):
1,1-dichloro-2-propanone 0.0072 0.0001
1,1,1-trichloro-2-propanone 0.0082 0.0003
heptachlor 0.25 0.00001
heptachlor epoxide 0.0107 0.0002
hexachlorobutadiene 0.044 0.001
hexachlorocyclopentadiene 0.060 0.000002
lindane 0.055 0.00001
methoxychlor 0.050 0.0001
pentachlorophenol 0.096 0.001
simazine 0.120 0.004
styrene 0.150 0.0005
1,1,2,2,-tetrachloroethane 0.081 0.001
tetrachloroethylene 0.081 0.001
toluene 0.078 0.001
2,4,5-TP (silvex) 0.270 0.0016
tribromoacetic acid 0.042 0.001
1,2,4-trichlorobenzene 0.160 0.0005
1,1,1-trichloroethane 0.084 0.0046
1,1,2-trichloroethane 0.150 0.0005
trichloroethylene 0.180 0.0010
trihalomethanes (includes):
chloroform (surrogate chemical)
bromoform 0.300 0.015
bromodichloromethane
chlorodibromomethane
xylenes (total) 0.070 0.001
CALIFORNIA PROPOSITION 65 WARNING
WARNING:
This product contains chemicals known to the
State of California to cause cancer or birth
defects or other reproductive harm.
8• PENTAIR US-1500 Monitored Dual Filtration System Installation and Operating Instructions

PENTAIR US-1500 Monitored Dual Filtration System Installation and Operating Instructions • 9

10 • PENTAIR US-1500 Monitored Dual Filtration System Installation and Operating Instructions

PENTAIR US-1500 Monitored Dual Filtration System Installation and Operating Instructions • 11

For Pentair§Product Warranties visit:
Pentair para las garantías de los productos visite:
Pour Pentair garanties produit visitez le site :
waterpurification.pentair.com
}
146600 REV D AP18
13845 BISHOPS DR., SUITE 200, BROOKFIELD, WI 53005
WATERPURIFICATION.PENTAIR.COM | CUSTOMER CARE: 800.279.9404 | [e-mail]
© 2018 Pentair Residential Filtration, LLC. All rights reserved.
§For a detailed list of where Pentair trademarks are registered, please visit waterpurification.pentair.com/brands. Pentair trademarks and logos are owned by
Pentair plc or its affiliates. Third party registered and unregistered trademarks and logos are the property of their respective owners.
13845 BISHOPS DR., SUITE 200, BROOKFIELD, WI 53005
WATERPURIFICATION.PENTAIR.COM | CUSTOMER CARE: 800.279.9404 | [e-mail]
© 2018 Pentair Residential Filtration, LLC. All rights reserved.
§For a detailed list of where Pentair trademarks are registered, please visit waterpurification.pentair.com/brands. Pentair trademarks and
logos are owned by Pentair plc or its affiliates. Third party registered and unregistered trademarks and logos are the property of their
respective owners.
PENTAIR RESIDENTIAL FILTRATION, LLC
13845 BISHOPS DR., SUITE 200 BROOKFIELD, WI 53005
262.238.4400, waterpurification.pentair.com
CUSTOMER CARE: 800.279.9404
EMAIL: [e-mail]
13845 BISHOPS DR., SUITE 200, BROOKFIELD, WI 53005
WATERPURIFICATION.PENTAIR.COM | CUSTOMER CARE:
800.279.9404 | [e-mail]
© 2018 Pentair Residential Filtration, LLC. All rights reserved.
13845 BISHOPS DR., SUITE 200, BROOKFIELD, WI 53005
P: 262.238.4400 | F: 262.238.4418
WATERPURIFICATION.PENTAIR.COM
CUSTOMER CARE: 800.279.9404
[e-mail]
© 2017 Pentair Residential Filtration, LLC
All rights reserved.
13845 BISHOPS DR., SUITE 200, BROOKFIELD, WI 53005 USA
P: 262.238.4400 | WATERPURIFICATION.PENTAIR.COM | CUSTOMER CARE: 800.279.9404 | [e-mail]
© 2018 Pentair Residential Filtration, LLC. All rights reserved.
§For a detailed list of where Pentair trademarks are registered, please visit waterpurification.pentair.com/brands. Pentair trademarks and logos are owned by
Pentair plc or its affiliates. Third party registered and unregistered trademarks and logos are the property of their respective owners.
13845 BISHOPS DR., SUITE 200, BROOKFIELD, WI 53005 USA
P: 262.238.4400 | WATERPURIFICATION.PENTAIR.COM
CUSTOMER CARE: 800.279.9404 | [e-mail]
© 2018 Pentair Residential Filtration, LLC. All rights reserved.
§For a detailed list of where Pentair trademarks are registered,
please visit waterpurification.pentair.com/brands. Pentair
trademarks and logos are owned by Pentair plc or its affiliates.
Third party registered and unregistered trademarks and logos
are the property of their respective owners.
13845 BISHOPS DR., SUITE 200, BROOKFIELD, WI 53005 USA
P: 262.238.4400 | WATERPURIFICATION.PENTAIR.COM
CUSTOMER CARE: 800.279.9404 | [e-mail]
© 2018 Pentair Residential Filtration, LLC. All rights reserved.
§For a detailed list of where Pentair trademarks are registered, please visit waterpurification.pentair.com/brands.
Pentair trademarks and logos are owned by Pentair plc or its affiliates. Third party registered and unregistered
trademarks and logos are the property of their respective owners.
13845 BISHOPS DR., SUITE 200, BROOKFIELD, WI 53005 USA
P: 262.238.4400 | WATERPURIFICATION.PENTAIR.COM | CUSTOMER CARE: 800.279.9404 | tech-supportpentair.com
© 2017 Pentair Residential Filtration, LLC. All rights reserved.
§For a detailed list of where Pentair trademarks are registered, please visit waterpurification.pentair.com/brands. Pentair trademarks and logos are owned by
Pentair plc or its affiliates. Third party registered and unregistered trademarks and logos are the property of their respective owners.