Percussion Play Sonora User manual

Ground Fixed
Components:
1. Carefully lay 2 x legs on a
level surface and insert
M10x200 bar and nuts. Using
packing box as protection lay
instrument note side down on
the card. Line up pre drilled
holes in the backboard with
the legs and ensure the
instrument is aligned square
with the legs. Fix in place
using M10x100mm screws
supplied (see installation
guide)
2.(See ground fix
sheet)Excavate 2 holes on site
of installation approximately
500mm deep ( adjust depth
according to age range for
intended players)
3. Carefully raise the
instrument from the ground
with legs attached and locate
(lower) legs into holes making
sure they are vertical and level
prior to concreting in place.
Installation Instructions
4. Once happy with location
and levels, fill holes using
rapid hardening concrete. Be
sure to compact concrete
around legs and leave to dry
according to manufactures
guidelines
5. Beaters can be fixed to
Stainless Steel posts with
fixings provided
1100
Ground Surface
Spares available form
percussionplay.com or from your
local distributor
Pair Small
Beaters X2 42 Kg
BS EN 1176
1.5m
Weight of heaviest part 30kg
1.5m
500mm
Install Instrument
with 1.5m free space
(from widest point)
around it.
Sonora
Page 1 of 3
M10x200 Threaded Bar
x4
M10 Nut
x8
Ground Fix
Components:
M10x100 Security Screw
x4
M10 Flanged Slide Bearing
x8
M6x20mm
Secure Screw
Eye Straps
Thread Lock Solution
Required (Not Supplied)
x2
KS1 –750mm
KS2 –900mm
Adult –1100mm
x4
Metric Conversion:
500mm/ 20”
750mm/ 30”
900mm/ 35”
1100mm/ 43”
1.5m/59”

Ground Fixed
Assembly Guide PPSWAV
37 Kg
Spares available form
percussionplay.com or from your
local distributor
BS EN 1176
Pair Small
Beaters X2
Sonora
Page 2 of 3
Saddle Strap X2
M6x20 Pin torx X4
COMPONENTS LIST:
M10x100 Pin torx X4
M10 Black Slide Plastic Bearing X8
M10 Nut X8
M10x200 Threaded Bar X4
TX 45 Driver Bit
x1
TX 30 Driver Bit
x1
Tools:
Components:
M10x200 Threaded Bar
x4
M10 Nut
x8
Ground Fix
Components:
M10x100 Security Screw
x4
M10 Flanged Slide Bearing
x8
M6x20mm
Secure Screw
Eye Straps
Thread Lock Solution
Required (Not Supplied)
x2
x4
Thread Lock Solution
Required (Not Supplied)

Excavate 2 holes with a 250mm diameter tapering
down to 350mm diameter and 550mm depth
Compact base of hole with 50mm of aggregate. Lower
ground Fix posts attached to instrument into hole (check
instrument straight and level, and at correct height
before filling with concrete)
Fill hole with fast drying concrete to manufacturers
specifications. If posts protrude above instrument they
can be cut down
Ground Fix Installation
(1.1)
1 2
Ground Fixed
BS EN 1176
Sonora
Page 3 of 3
M10 BZP Nut
X8
M10x200mm
BZP Bar
X4
Components:
3
Foundations should not present a hazard. These foundations are
recommended as a guide, for more information on foundation
details for various surface see Part 7 of BS EN 1176.
Metric Conversion:
50mm/ 2”
250mm/ 10”
350mm/ 14”
550mm/ 22”
759mm/ 2 ft 5 7/8“
835mm/ 2 ft 8 7/8“