Perin WeighMaster 1500 Instruction Manual

Via P. Borsellino, 15
26845 ODOGNO (LO)  ITALY
Tel. + 39 - 0377 - 43.70.33 Fax 43.70.46
www.farmscale.com
e-mail: [email protected]

USER'S HANDBOOK
Valid for Models 1500-1510-1520-1530
English

INDEX
Page
1 - Safety regulations for the installation and maintenance of the system..................3
2 - onnections...........................................................................................................3
3 - Disposal of the device............................................................................................3
4 - Description of the device........................................................................................4
5 - Display messages............................................................................................................5
6 - Maintenance............................................................................................................5
7 - Battery test.......................................................................................................................5
8 - Language selection.........................................................................................................5
9 - Switching on and zeroing (tare)....................................................................................6
10 - Main functions of the indicator...................................................................................6
10.1 NET/TOT function: partial weighings...................................................................7
10.2 BLO function: weight blockage............................................................................7
10.3 PROGR function: programming rations..........................................................7
10.3.1 Example programming ration n° 1............................................................7
10.4 UNLO function: programming unloading rations................................................9
10.4.1 Example programming unloading ration n° 1.........................................9
10.5 EXE function: executing rations.......................................................................9
10.5.1 Example executing ration n° 1.............................................................10
10.6 NAMES function: changes/creates name file................................................11
10.7 STORAGE function: consulting total storage...............................................12
10.8 Ration integration...............................................................................................12
10.9 LO K function: setting current date/time..................................................12
11 - Printing...............................................................................................................12
12 - Troubles and solutions.................................................................................................13
13 - System representation.........................................................................................14
14 - Accessories on demand..................................................................................15
15 - Technical details...........................................................................................................17
Declaration of onformity................................................................................18
Warranty....................................................................................................................19

WARRANTY CONDITIONS: Warranty covers the material and manufacturing defects, and includes
both spare parts and manpower for the substitution at our warehouse. Warranty starts from the
purchasing date and has a validity of 24 months.
The possible freight charges have to be paid by the customer.
Warranty cannot be applied if the damages are due to improper installation, bad use, ill-treatment,
deterioration, lightnings, weather phenomena, over-voltage, over-current, insufficient or irregular
power supply. Moreover, warranty is not acknowledged if damages have been caused during the
transport from and to the customer, or if they are due to a use that is inconsistent with the
technical/safety measures demanded in the country where the device is used.
If, during the warranty period, one or more components are replaced - for the reparation - with
spare parts which are not supplied or approved by the producer, or in case reparation is carried
out by non-authorized people, Perin Weighmaster S.r.l. reserves the right to revoke immediately
the warranty with no further information.
Warranty is appliable only if there are the producer's label and anti-tamper label on the device.
Perin Weighmaster S.r.l. is not responsible for any direct or indirect damages, caused to people
or things, due to the operator's inability or to a breakdown of the device with the consequent
stoppage of its use.
If spare parts not included in warranty (external covering, batteries, rubber parts) needed replacing,
their cost would be debited to the customer together with the corresponding labour cost.
In case of shipment, pack correctly the device and write down a brief explanation of the problem.
NOTES

Indicator 1500-1510-1520-1530 3
3 - Dis osal of the device
This symbol present on the product or on the handbook indicates that the product
cannot be thrown together with household garbage (European Directive 2002/96/EG).
The final user has to dispose of the device at a gathering place for recycling and
disposal of electrical and electronical devices. The separate refuse collection and
the correct recycling of the devices allow to protect the health of people and
ecosystem. For further information concerning gathering points for devices, contact
the local authority for the disposal of garbage or the distributor where the product
has been purchased.
1 - Safety regulations for system installation and maintenance
- Install only when power supply is disconnected.
- Do not install the device near heat sources or near strong magnetic fields.
- Disconnect the power supply cable from the weight indicator when you need to recharge the battery
of the means of transport.
- Immediately disconnect the power supply cable if the cables or the connectors are stripped or
damaged, if the system has particular problems or if there is liquid/humidity in the device.
- The tension should stay between 12V and 14V to avoid damaging the other parts of the system.
The device works correctly with tensions between 10V and 24V.
- Before cleaning the machine with high pressure waterjets, disconnect the cables, remove the weight
indicator from the machine and protect the connectors of the cables from water seepage.
Pay attention that the load cells, the junction box, the alarm and other accessories are not exposed
to direct waterjets.
If the device needs to be cleaned, use soft and lightly humid cloths.
Do not use sprays, solvents, abrasives, sharp or cutting objects which could damage the case.
- Do not open the device, to avoid losing the warranty right. For maintenance/reparation, address
to our company or to technical authorized staff.
- Before doing any welding on the machine, disconnect the cables.
To prevent welding current from passing through load cells, it is necessary to shortcircuit the body
of the load cells with a cable with adequate section and the earth of the welder must be connected
near the point where you weld.
2 - Connections
The device has got three connectors. From left to right: a 5 pin connector for the connection of the
extension cable (LOAD ELLS), a 7 pin connector for the connection of remote displays (STARBUS),
a 3 pin connector for the connection of the power supply and alarm cable (POWER), a 5 pin connector
for cartridge ( ARTRIDGE).
Before making connections, make sure that the device and the possible peripherals are off.
Before introducing any connector, make sure it is the right one and then connect it adequately
otherwise damages to the device could occur.
After having introduced the connector, screw the fixing ring.
To disconnect the cables from the plugs, rotate the upper ring anticlockwise, keeping the lower ring
steady. Pull out the connector. Do not pull the cable directly.

Indicator 1500-1510-1520-1530
4
Recipe No.
Indicator
Ingredient No.
indicator
ondition
indicators
Display
functions
Values
display
Function keys
Switch on/off
Operative and
numerical keys
Alarm output
and low battery
indicator
Recipe No
indicator
Ingredient No
indicator
Low battery
indicator
ondition
indicators
4 - DESCRIPTION OF THE DEVICE
onnector
for load cells
Power supply -
alarm output
connector
StarBus
connector
for extra
peripherals
onnector
for cartridge
(optional)
O erative and numerical keys
: switches the device on; keep it pressed to switch off.
: zeroes the values displayed during the programming.
: confirms the programmed values.
The numerical keys from 0 to 9 allow to program the values and names using the corresponding
numbers and letters. The key allows to scroll the pages of the menu where the
different functions are listed.
NET BLOC START PROG
Menu: more functions
Function keys
The four keys between the two displays allow to select the functions indicated in the first line
of the function display.
The values display of Model 1510 - 1530 has 4 digits, but in case the value passes 9999, another
window showing on its left the tens of thousands column is displayed alternately.
The values display of Model 1500 - 1520 has 5 digits.
15
1
210. .
+
-

Indicator 1500-1510-1520-1530 5
8 - LANGUAGE SELECTION
7 - BATTERY TEST
If you want to select a language different from the preset one, when you switch the indicator
on, after the inscription "Options detected", press to see the list of the languages
(Italian, English, French, German, Spanish, Dutch, Portuguese, zech, Russian). Digit the
number corresponding to the required language and wait that the indicator sets in the new
language and goes to direct reading.
It is advisable to test the battery periodically (entrance tension value to the weight indicator).
To carry out this test, switch the indicator on using ; keep pressed and release
it; a "t" with the voltage of power supply will be displayed and the acoustic device will
intermittently sound. Press the key again to have the weight direct reading.
6 - MAINTENANCE
The weight indicator does not require any regular maintenance, however it is necessary to
check the conditions of the weighing system periodically.
1) Make sure that there are no disturbing elements between the supporting chassis and the
platform or the container, the basin, the feeder, etc.
2) Make sure that the load cells are not damaged (no cracks nor dents), not rusty, not
corroded by acids.
3) Make sure that there is enough space between the chassis and the components of the
weighing systems; lubricate if necessary.
4) Make a test: load a weight on each corner, the displayed amount must be nearly the
same.
5) Make sure that the connectors are tight and that the cables are undamaged (no cuts nor
abrasions). Remember that, where food is stored or handled, small rodents often gnaw
cables which are situated in hidden or scarcely reachable places.
6) heck there is no oxidation or humidity on the connecting points.
7) heck that the silicone used to seal the different parts of the weighing system is intact
otherwise there could be water seepage.
NOTAR
4 - DISPLAY MESSAGES
HEllo
tArE
out
t 12.5
Or-L Or-H
Start message
Low battery level
Intermittent signal
(for 1510/1530 point on the
right of the display)
Zeroing
Damaged alarm output
Battery voltage
Zeroing mistake
Out of range (low) Out of range (high)
+-

Indicator 1500-1510-1520-1530
6
If you press once again, you go back to the first menu.
The weight indicator has several functions indicated in three different menus. To select a
function you have to press the key above the corresponding inscription. To pass from one
menu to another one, use
net BLOC start PROG
Menu: more functions
group nAme storage
Menu: more functions
cloc setting
Menu: back to total
10 - MAIN FUNCTIONS OF THE WEIGHT INDICATOR
1st MENU: after switching the device on, the following menu appears
NET/TOT: executes the partial zero and recalls the total (par. 10.1).
BLO : blocks the weight (par. 10.2).
START: executes the recipes (par. 10.5).
PROGR: programs the recipes (loadings) (par. 10.3).
2nd MENU: press to gain access to more functions
GROUP: programs the unloadings (par. 10.4).
NAME: programs the names of recipes, ingredients and groups (par. 10.6).
STORAGE: consults the stored quantities (par. 10.7).
3rd MENU: pressing again the last menu appears
LO K: sets date and time of the inner clock (par. 10.8).
SETTING: gets access to the operative parameters of the device (see the adjustment
handbook).
9 - SWITCHING ON AND ZEROING (TARE)
After switching on with , the indicator displays "Hello" and then the model and the
version of the device. The total weight is displayed with an indicator above TOTAL and
another one above the unit of measurement (the latter indicator only appears on model 1500-
1520). NB: in the beginning it might be necessary to adjust the zero until the mechanical
parts of the system settle.
To put to zero (tare), keep the TOTAL/NET key pressed until the display shows the message
"tArE". The indicator is ready to weigh (direct reading).

Indicator 1500-1510-1520-1530 7
10.3.1 Programming ration n° 1 - Exam le
We want to feed 120 animals of LA TATION group, programming ration n° 1 called "MIX
1" (with mixing time of 5 minutes on Flour) composed of the following ingredients:
1 - OATS* 1,10 Kg
2 - FLOUR 2,25 Kg
3 - SILO ORN 9,20 Kg
4 - INTEGRATOR 0,72 Kg
* The programming of names is optional.
Select PROGR pressing the key above the name of the corresponding function on the first
page of the function list. The first ration is proposed. If you want to choose a different one,
digit the corresponding number on the keyboard.
To assign a name to the recipe, press the
PROGRAM RE IPE key several times. The stored
names will be displayed in a list. Press until
MIX 1 appears and confirm with .
100.00
Total MIX 1
10.1 NET/TOT function: artial weighings
Use the TOTAL/NET function to load/unload displaying the partial weight. The indicator above
TOTAL or NET indicates the condition.
10.2 BLOC FUNCTION: weight blockage
When you are loading or unloading, and the feeder is moving or standing on uneven ground,
it is sometimes useful to "freeze" the weight value. Press the BLO K key once to block the
weight. The indicator sounds every 5 seconds to remind you of the blockage. Press the same
key to disconnect the blockage.
!
10.3 PROGR function: rogramming rations
The indicators 1500/1510 have a memory able to store up to 20 recipes (99 recipes for
indicators 1520/1530) each one composed of 20 ingredients for loading and 10 groups for
unloading. It is possible to assign a name (names can be chosen from a pre-existent list or
can be later added to the Name File) to every recipe, ingredient and unloading group.
When programming, the loading ingredients refer to the individual animal and are expressed
in the unit of measure selected with two decimals. For each ingredient it is possible to program
a mixing time, expressed in minutes, useful during execution to have a timer with alarm
between the loading of an ingredient and the following one.
The functions written in the first line of the display are recallable with the keys placed above
the inscriptions and allow, among other things, to go back to the previous step.
Make sure that at the time of blocking and unblocking the machine and the augers
have been firm for some seconds (the weight value must be steady) and that there
are no points of support on the under weighing part, otherwise there could be
variations in the total weight.

Indicator 1500-1510-1520-1530
8
To program the value of the first ingredient (1,10
Kg), digit 110 on the numerical keyboard. To give
the name OATS, scroll the name list with the
corresponding key and confirm with to
pass to the following ingredient.
Program 225 for the second ingredient and assign
the name FLOUR. onfirm with .
To assign 5 minutes of mixing time, press BLO K,
the key 5 and confirm with . onfirm the
weight value with .
Program 920 for the third ingredient and assign
the name SILO ORN. onfirm with .
Program 72 for the fourth ingredient and give the
name INTEGRAT. onfirm with .
Press several times to scroll the following
ingredients until the 20th. After the last ingredient
the total of the recipe will be displayed.
To leave the function PROGRAM RE IPE and go back to total, press TOT/NET.
1_1.10
1
Ingredient OATS
1_2.25
2
Ingredient FLOU
1_9.20
3
Ingredient SILOCO N
1__.72
4
Ingredient INTEG AT
113.27
Total MIX 1

Indicator 1500-1510-1520-1530 9
10.4 GROUP function: rogramming unloading grou s
The indicator can program for each recipe up to 10 unloading groups to which it is possible
to assign a name. Each unloading group has to be entered in number of animals (to allow
the device to multiply the value of the entered ingredients by the number of animals, it is
necessary to enter at least one unloading group).
Moreover for each unloading group there is the possibility to assign a percentage coefficient
in order to increase or decrease the incidence on the total of the ration.
Every unloading group, with the corresponding animal number and coefficient, is reproposed
during the ration execution for confirmation or variation. The changes are stored for the new
ration calculus and are reproposed during following executions.
10.4.1 Exam le of rogramming unloading ration n° 1
Select the GROUP function pressing once
and once TOTAL/NET (two indicators
appear above PROG and UNLO). Press
to confirm.
The value of the first group flashes and it is
possible to digit number 120 on the keyboard.
To give the name LA TAT. 1 to the group, use
the PROGRAM/RE IPE key which allows to scroll
the list of the names in the file. Press to
confirm the first group.
The second group is proposed. Leave the value
at Zero and press several times to scroll
the remaining groups up to the tenth.
1
0000
Total Cows MIX 1
1120
1
Group Cows Lactat.1
1120
Total Cows MIX 1
After having programmed the rations and the possible unloading groups, it is possible to use
the ration execution function. The indicator allows to change the animal number - previously
programmed - in order to adequate the quantity of each ingredient according to the daily
needs. If the unloadings have not been programmed, during the execution the indicator
requires the number of animals to be able to multiply the values of each ingredient and obtain
total quantities for the loading. When entering the number of animals it is also possible to
change the % coefficient (usually with value 100) to get a proportional increase or decrease
of the quantity of each ingredient. The given values (animal number and % coefficient) are
stored and reproposed the following time.
To leave the unloading programming function, press TOT/NET.
10.5 START function: ration execution

Indicator 1500-1510-1520-1530
10
10.5.1 Exam le of execution ration n° 1
Press START/LOAD to select the ration execution
function. The indicator is above START and the
first recipe with the total programmed per animal
is displayed. To choose another recipe press the
corresponding number on the numerical keyboard.
Press to confirm. The number of animals
(if it is zero, enter a value using the numerical
keys) which was previously programmed flashes.
Press to confirm.
The indicator is ready to load the first ingredient
(START and LOAD announcers are flashing).
During the execution of rations it is possible to activate the following functions by means of
the keys placed above these inscriptions PREV BLOC RESET MODE
PREV: goes back to the previous step
BLO : blocks the weight value. The displayed value flashes.
RESET: restores the value of the programmed ingredient.
Load and the display will show that the value decreases in proportion to the loaded quantity.
1120
1
1132
1
113.27
Total MIX 1
Group Cows LACTAT.1
Ingredient OATS
In ration execution, both with loading and unloading, the partial weight value is usually
displayed; pressing the key 1, you activate the function for the visualization of the total (the
TOTAL indicator lights up).
Pressing 1 again, the function is deactivated and you go back to the partial visualization.
Re ro ortion ingredients: if, during the loading of the first ingredient, the key "0" is pressed,
the digit of the first ingredient flashes. At the end of the first ingredient the quantity actually
loaded is checked and, if it is bigger or smaller than the theoretical one, all the other ingredients
are reproportioned in percent.
Re ro ortion unloadings: if, before ending the last loading, you press the key "5", the digits
of the recipes flash. At the end of the loading, the total loaded quantity is indicated and the
unloadings are reproportioned in percent.
When 85% of the load has been reached, you will hear an intermittent signal: load
with care. When 100% has been reached, you will hear a continuous signal: stop
loading immediately.
!

Indicator 1500-1510-1520-1530 11
10.6 NAME function: change/create name file
The indicator allows to assign names (useful during loading/unloading) to recipes, ingredients
and unloading groups. The names can contain up to 8 digits (letters and numbers). Some
common names have already been stored in the indicator; they can anyhow be modified. It
is moreover possible to add other names, up to 254.
Names already stored
001 - MIX 1
002 - MIX 2
003 - MIX 3
004 - MIX 4
005 - MIX 5
e.g. for recipe names
006 - WATER
007 - OATS
008 - OTTON
009 - FLOUR
010 - HAY
011 - GLUTEN
012 - INTEGRAT
013 - RYEGRASS
014 - ORN
015 - WHEAT
016 - ALFALFA
017 - SORGHUM
018 - BARLEY
019 - STRAW
020 - MASH
021 - LEGUME
022 - MIN SALTS
023 - SILO ORN
024 - SOYA
e.g. for loading ingredients
025 - DRY OWS
026 - HIGH OWS
027 - LOW OWS
028 - LA TAT.1
029 - LA TAT.2
030 - HEIFERS
031 - OXEN
032 - ALVES
e.g. for unloading groups
033 - ........
034 - ........
254 - ........
personal added names
To get access to the name list, press and then BLO . The first name of the list
appears. Press to scroll the following names of the list and find an empty location.
To introduce the new name GRASS, it is necessary to digit the following combination: 3-666-
1-7-7; press to confirm.
Press TOTAL/NET to end programming.
Exam le of name addition
MODE: establishes the mode of passage to the following ingredient, when 100% of the
loading has been reached. In automatic mode the alarm lasts 5 seconds, in manual
mode the alarm lasts until is pressed.
With it is moreover possible to pass to the following ingredient without completing
the loading procedure.

Indicator 1500-1510-1520-1530
12
10.7 Storage Function: consult loaded quantities
The quantities of the ingredients loaded for each recipe are stored by the indicator memory
in order to allow a weekly, monthly, yearly control. Thanks to the storage function it is possible
to verify the values, stored from a given date, for each ingredient of the recipes.
To select this function press once and once PROGRAM RE IPE. It is possible to
recall the recipe digiting the corresponding number on the numerical keyboard. Pressing
several times it is possible to scroll the 20 ingredients with the consumption values.
Moreover you can put to zero the values of the storage connected to each ration by selecting
the corresponding function. When you zero the storage, the new starting date is indicated.
Press TOTAL/NET to end the consultation.
10.9 Clock Function: setting current time and date
Press twice and select the clock function pressing TOTAL/NET.
- Enter the current time in the 24-hour-format (e.g. 18 for 6 p.m.) and press
- Enter the day (2 digits) and press
- Enter the month (2 digits) and press
- Enter the year (4 digits) and press
With models 1500 - 1510 - 1520 - 1530 you can manage an integration to be added to the
base ration. It is useful whenever you need a differentiated feeding for some groups having
the base ration in common. To link the integration and the base ration together, during
programming it is necessary to set the following not used unloading, corresponding to the
base ration, introducing the name @INTEGRA (pressing the key START LOAD during setting)
and leaving the number of animals at zero. During execution, when the base ration is
concluded, loadings and unloadings of the following ration (integration) will be automatically
recalled.
For the models associated to thermal printer (par. 14), it is possible to have an exhaustive
printing of all the operations carried out both during loading and during unloading. On the
bill there are: names of the ingredients, date and time of beginning/end of the operation,
duration of the operation.
In total visualization of the starting menu, press the key 6 to reprint the last loading/unloading
operation. It is also possible to get an automatic printing of the copy of the last operation,
by setting a technical parameter (see technical handbook).
10.8 Ration Integration
11 - PRINTING

Indicator 1500-1510-1520-1530 13
12 - TROUBLES AND SOLUTIONS
Here is a list of some troubles and their possible solutions. If your problem is not included
in this list, contact your retailer or the producer PERIN WEIGHMASTER.
Beware: switch the indicator on at least 10-15 minutes before doing the tests.
SOLUTIONS
check connections, polarity, external fuses, battery, cables
recharge the battery or replace it; check connections, external fuses, battery
and cables
check the condition of load cells, cables and connectors
disconnect the load cells one by one. If the problem is not caused by load
cells, check the connections between the junction box, the connecting cable
and the indicator
the system may have lost the correct calibration (it may have received
shocks or strong vibrations). The calibration value must be reset.
check the zeroing while the container is empty. Make sure that there are
no disturbing elements between the chassis and counterchassis. Put a test
weight on every corner, possibly above the load cells to detect the damage.
Ask for technical assistance
check the binary connector. Use a 12 Volt battery to supply the alarm device
separately. Substitute it with a new alarm if necessary
out of range (high or low): check the connectors and the load cells cables;
disconnect the load cells one by one. Substitute the damaged load cell.
Restore the connections.
recharge the battery and restore the connections
TROUBLES
The system does not switch on
The device switches on, but after a
short time it switches off
Unstable value on the display
The displayed value flows towards a
direction (20÷30 times in an hour)
The displayed value is not correct:
there is a small percentage mistake
The displayed value is wrong (mistake
higher than 10%)
While loading the alarm does not work
The indicator displays the message
"Or-L" or "Or-H"
The indicator displays the Battery
symbol

NET
BLOC START PROG
Menu: more functions
15
1 210..
Model 1510
Model 1500
NET
BLOC START PROG
Menu: more functions
+
-
REM 40/A
1510
14 Indicator 1500-1510-1520-1530
LOAD ELLS
KIT FARMLINK
(optional)
StarBUS
REMOTE DISPLAYS
(numeric or
alphanumeric)
PRINTER
ticket example
ONTROL
OUTGOING
RELAY
MODULE
REM 40/A
1500
ONTROL
ON/OFF INPUT
ONDITION
RADIO
TRANSMITTER
UNIT
REMOTE
RE EIVER UNIT
Silocorn
WEIGHT INDI ATOR
13 - SYSTEM REPRESENTATION
+-
12/24 Volt
acoustic alarm

Very compact and easy to install. Made in a watertight box
(humidity and water-proof), it can be used on trailed and
self-propelled mixers.
Paper changing is carried out by opening the frontal panel.
It is provided with a 40-column-print mechanism on thermal
paper 57,5 mm wide.
FEATURES
Printing Method thermal
Columns 40
Paper type thermal
Paper width 57,5 ± 0,5 mm
Roll measure ø 50 mm (M X)
Connection StarBus
Connecting cable 1 or 3 metres
Dimensions 180 x 180 x 120 mm
Working temperature 0°C ÷ 50°C
Indicator 1500-1510-1520-1530 15
Thermal rinter
LED LF alphanumerical
LED with digits 30 mm high
L 315 x H 130 x W 105 mm
Our remote displays allow high visibility at a distance also in conditions of poor illumination or
direct sunlight.
- Sealed ABS box.
- Slide tool with dovetail for fixing.
- onnection to weight indicator by means of StarBus cable (several lengths).
- onnection to radio kit.
Remote dis lays
LCD REM/54 numerical
LCD with 5 digits h 54 mm
L 215 x H 170 x W 90 mm
LED REM 57 numerical
LED with digits 57 mm high
L 315 x H 130 x W 105 mm
14 - ACCESSORIES ON DEMAND

The targets of the program are:
- optimization of raw material management for animal feeding
- optimization of the use of manpower employed for the preparation of rations
- improvement of the quality of the ration distributed to the individual cattle groups with
relevant increase of the quantity and quality of milk or meat produced
- improvement of the health of the animal
- traceability of the food distributed to the individual cattle groups
- automatic calculation of IOF (Income Over Feed ost)
- minimizing of expenses and wastes
16 Indicator 1500-1510-1520-1530
This remote display is combinable with models
1500 and 1510 and interacts with them by means
of function keys and alphanumeric keys.
It is connectable to the weight indicator by means
of a starbus cable or via radio by means of a
transmitter/receiver unit.
It is used in the tractor cabin or on telescopic
machines for the loading of components.
Remote dis lay 1500R
FarmLink is a software for P , working with Windows in combination with Perin Weighmaster's
weighing systems (models Farm Scale: Visual 2000, 1500, 1510, 1520, 1530). These weighing
systems are usually installed on "UNIFEED" mixer wagons of several makes or on mills for
food preparation.
The software can be installed on new or already existing mixers (even if originally preset
with scales of other makes), without having to change the load cells.
FarmLink is an important help to create reports that are essential to manage Quality, moreover
it is indispensable for the farms which want to attest the traceability of livestock feeding.
FarmLink 4
Advanced management of traceability and cattle feeding
FarmLink
Numerical backlit L D for weight and for
recipe/ingredient number; additional alpha-
numerical backlit L D for help messages and
names of recipes, ingredients and unloading
groups; display announcers indicating the present
operation; function keys for a quick recall of
operations; alphanumerical keyboard for an easy
entry of values and names; menu and messages
available in different languages.

Indicator 1500-1510-1520-1530 17
+-
15 - TECHNICAL DETAILS
 POWER SUPPLY VOLTAGE 12/24 V 0,45 A
 WORKING TEMPERATURE -10°/ +40°
 MILITARY TYPE ONNE TORS FOR POWER SUPPLY
AND LOAD ELLS
 DISPLAY BA KLIT L D (1500-1520)
LED (1510-1530)
 DIGITS FOR THE WEIGHT VALUE 5 DIGIT h 40mm (1500-1520)
4 DIGIT h 40mm (1510-1530)
AND FOR THE RE IPE AND INGREDIENT NUMBER 4 DIGIT h 14mm (1500-1520)
4 DIGIT h 10mm (1510-1530)
 ALPHANUMERI AL L D WITH 2 LINES OF 20 DIGITS EA H
 INDI ATORS FOR: TOTAL/NET, EXE UTION, PROGRAMMING,
STORAGE, LOADING/UNLOADING, LB/KG, RE IPE, INGREDIENT
 PROGRAMMABLE DIVISIONS 1 - 2 - 5 - 10 - 20
 MAXIMUM RESOLUTION 24 BITS
 MEMORY FOR 20 RE IPES (1500-1510)
99 RE IPES (1520-1530)
EA H ONE WITH 20 INGREDIENTS + 10 UNLOADINGS
 PROGRAMMING WITH NUMBER OF ANIMALS OR IN TOTAL VALUES
 AUTOMATI PROPORTIONAL AL ULATION OF EA H INGREDIENT
A ORDING TO THE SET NUMBER OF ANIMALS
 INGREDIENTS USEFUL BOTH FOR LOADING AND FOR UNLOADING
 PREALARM AT 85%, ONTINUOUS ALARM FOR 5 sec. WHEN
LOADING/UNLOADING IS OVER
 "Err Out" MESSAGE IN ASE OF SHORT IR UIT AT THE ALARM
OUTPUT
 IN ASE OF LOW BATTERY LEVEL
 HOLD AND WEIGHT RESTORATION FUN TIONS
 ZEROING, ALIBRATION, DIVISION SETTING, BATTERY TEST BY
KEYS
 HERMETI ABS BOX
FARMLINK4 PROGRAM CAN WORK WITH ALL THE INDICATORS,
MODELS 1520 AND 1530 WORK ONLY WITH MEMORY CARTRIDGES
OF 256K
1500/1510 vers. 3
1520/1530 vers. 1.2

The producer
PERIN WEIGHMASTER SRL
Via P. Borsellino 15
26845 odogno (LO)
declares that the below-mentioned equipments are in accordance with
the essential requirements of the applicable directive:
1 Electromagnetic ompatibility Directive 2014/30/UE
EN55022:2010 EN61000-6-2:2005 EN61000-6-4:2007
odogno, 16th May 2016
The technical head
Fabio Perin
Denomination Weighing System
1500 - 1510
1520 - 1530
Models
CE Declaration of conformity