Perle IRG7440 User manual

IRG7440 5G Cellular Router Quick Start Guide 5500480
Version #A01.13.2022
1
IRG7440 5G Cellular Router
Quick Start Guide
_____________________________________
This guide covers the basic installation and configuration of
the IRG7440 5G Cellular Router and is intended for first-
time setup or product evaluation.
Complete details can be found in the following guides at
www.perle.com/downloads.
•IRG7440 5G Cellular Router Hardware Installation
Guide
•IRG7000/5000 5G/LTE Router User’s Guide
•IRG7000/5000 5G/LTE Router Command Line Interface
Reference Guide
What’s in the box?
The following components may be included with your
product. Components will vary depending on each model.
See the Perle website for updates
•IRG7440 5G Cellular Router
•IRG7440 5G Cellular Router Quick Start Guide (this
guide)
•5G/LTE SMA antenna pack-4 (#08000530)
•GPIO Cable with 4 pin plug (#2500468)
•GPIO Cable with 8 pin plug (#2500476)

IRG7440 5G Cellular Router Quick Start Guide 5500480
Version #A01.13.2022
2
•12VDC/2A 4 pin (NA#08000150, EU #08000160, UK
#08000170, AUS#08000180)
•Orderable–GNSS PAV RP Antenna SMA/CA
(#08000130) passive
•Orderable–DIN Rail mounting kit (orderable from Perle)
Getting Started
Typical installation steps are:
1. Inserting the SIM card.
2. Connecting 5G/LTE antenna/s.
3. Connecting the Power.
4. Connecting to the Cellular Network.
5. Fast Setup Mode.
Inserting the SIM card
Use only a mini-SIM (2FF) card.
Ensure the power is disconnected before you insert the SIM
card.
1. Unscrew the screws and gently pry the SIM cover loose
from the opening (see below).
2. Align the SIM card so that the SIM card will slide into
the SIM slot, ensuring that the SIM card connectors will
be facing the router’s printed circuit board (face down).
3. Align the SIM cover plate and secure the plate with the
screws.

IRG7440 5G Cellular Router Quick Start Guide 5500480
Version #A01.13.2022
3
Connecting the 5G/LTE Antennas
1. Connect an antenna to the connector Main.
2. Connect an antenna to the connector MIM01.
3. Connect an antenna to the connector MIM02.
4. Connect an antenna to the connector DIV/GNSS L1.
See Figure 2
Connecting the Power
See Figure 2 for wiring requirements. The colors indicated
are for the Perle supplied DC cable.
Connecting to the Cellular Network
When the router is powered on, it begins activating and
attempting to connect to the cellular network. This process
typically takes a few minutes. A solid green WWAN LED
indicates a successful connection; if not, see the IRG7440 5G
Cellular Router Hardware Installation Guide for details.

IRG7440 5G Cellular Router Quick Start Guide 5500480
Version #A01.13.2022
4
Fast Setup Mode
Fast Setup provides a simple method of doing an initial setup
from a PC. Your router is shipped in factory default mode.
1. Your PC must be set to obtain an IP address
automatically using DHCP.
2. Plug the PC into your router’s Ethernet interface.
3. When the Power LED is flashing green, use a web
browser, enter http://192.168.0.1 to access your router.
On the setup screen, select, Getting Started.
4. Once connected, fill in the required fields, apply changes
to save and exit. Your configuration changes will be
immediately applied to the router
5. The router’s web configuration sign-on screen will be
displayed. Using the credentials you previously defined
in Step 4, you can now access your router’s full
configuration.
For alternative methods of performing and initial Setup, see
the IRG7440 5G Cellular Router Hardware Installation
Guide.
© 2022 Perle Systems Limited. All rights reserved.