PETKIT K2 User manual

K2
User Manual • Uživatelský manuál •
Užívateľský manuál • Használati utasítás

2
English
3 –16
Čeština
17 –30
Slovenčina
31 –44
Magyar
45 –58

3
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully
before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device,
please contact the customer line.
✉www.alza.co.uk/kontakt
✆[phone]
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

4
Introduction
Thank you for purchasing PETKIT K2, smart odour eliminator. Please read this user
manual carefully before using. Once the product is installed or used, it indicates that you
have carefully read and accept the safety instructions below.
Our company will neither assume any responsibility nor undertake any legal liabilities
for any accidents and damages caused due to violations. The company reserves the
right of explanation and revision for the terms.
Safety Instructions
Failure to comply with the following clauses may lead to that the product cannot be
normally used or occurrence of other accidental losses.
•Please use it indoors.
•Please use the original power adapter and PETKIT Concentrated Air Purifying
Refill.
•Please install and use device in strict accordance with the manual.
•In case of problems with using the product, please contact the customer service.
Package Contents
Mainframe cover ×1
Water barrel ×1
Concentrated Air Purifying
Refill ×1
Power Adapter ×1
Manual ×1

5
Product Introduction
Exterior appearance
Note: We will carry out regular product improvement in order to provide better
products. When the product picture is slightly different from the actual product, the
actual product shall prevail.
Mainframe cover (interior)
Filter screen in the mainframe cover
Display / touch screen
Air outlet
Air inlet
Silica gel pad
Mainframe cover
Water barrel
Water level
detector
Water gauge
MAX: Highest water level
0.3 litres: Liquid level
alarm mark
Water barrel

6
About Control Panel
Note: Switch between °C and °F in the PETKIT app.
Note: In case when the content is hotter than 100 °F, only the last two digits will be
displayed.
Key Functions
Functions
Operation
On / Off
Press the function key for a few seconds when the
keys are unlocked.
Switch mode
Click the function key when the keys are unlocked.
Enable locking
Automatic locking after double-clicking the locking
key or if there was no input in five seconds.
Unlock
Double click the lock key.
Start network pairing, the WiFi
indicator flickers and the
Bluetooth is enabled
Press the function key and the lock key at the
same time for a few seconds when the keys are
unlocked.
Ambient
temperature
display
Degree centigrade
Fahrenheit
WiFi indicator
Liquid shortage reminder
(the orange light wil be on in case of
lack of liquid)
Locking key
(the orange light will be on when the
touch controls are locked)
Function key

7
Mode Introduction
Quick Guide
Place the product in a right position.
To better exert the performance of AIR
MAGICUBE, a certain distance (no less than 10
centimetres) between air inlet and the shelter
(such as wall) shall be kept in use. Considering
different pet habits, it shall be placed in the
position where the pet cannot reach it.
Add the concentrated air purifying refill.
Add enough water to reach the water level mark
and pour the whole PETKIT concentrated air
purifying refill to the water barrel. Specifically, a
solution of nine parts water to one part mixture
should be formed.
Powerful mode
(Grade III wind speed –powerful air cleaning)
Standard mode
(Grade II wind speed –daily use)
Quiet mode
(Grade I wind speed –use at night)
Automatic mode (Auto)
(automatic choice of modes as per temperature
and humidity)

8
Complete the installation.
Align the mainframe cover with the water barrel,
then press down.
Switching on.
Connect the power adapter. After switching on for
the first time, the device will enter the default
mode (AUTO mode); or switch the mode by short
pressing the function key. (Refer to Key Functions
for the detailed description of key use.)
App Access
After powering on, observe the Wi-Fi indicator light
state. If the indicator light flickers, it means the
device entered the network pairing mode.
Note: In case of network change, press function key with
lock key at the same time for a couple of seconds under
the state of unlocking, until the Wi-Fi indicator light
flickers, and then start network pairing again.
Download and open “PETKIT” app to enter the home
page of the app, click “+” to add a new device and
select the device that should be added.
Connect the device with the network. You can use
the help of a video by clicking “Watch video”.

9
Cleaning and Maintenance
Before thorough cleaning of the device, please turn off the power supply and unplug the
power adapter.
Cleaning the cover
Remove the upper cover.
Pull out the filter screen at the bottom of the
cover. There should be no water in the remaining
parts of the cover.
Tips for taking down the filter screen: Pull out the white
periphery of the cover outward with left hand and
pinch the grey handle of the filter screen with right
hand thumb for lifting upward, as shown in the picture.
The filter screen should be rinsed with flowing
clear water or ordinary cleaner. Brush and sponge
from the PETKIT Cleaning Kit can be used for
cleaning, too.
It is suggested to use a clean, soft cloth for
scrubbing or brush and sponge from the PETKIT
Cleaning Kit for dust removal.

10
Cleaning the water barrel
Pour out excess liquid in the barrel.
The barrel should be rinsed by flowing clear water
or ordinary cleaner.
Do not use a chemical reagent, such as gasoline or
kerosene bleach.
The water gauge and the built-in water level
detector can be taken out for cleaning.
All parts included in the water gauge: Water gauge cover, float spindle (water level
detector), PE foam (water level detector)