Phenix Technologies PM-20 User manual

1
PM-20
Phenix Technologies, Inc.
75 Speicher Drive
Accident, Maryland 21520
PM-20
High Voltage Insulation Tester
User Guide
GU-1505RA
©Phenix Technologies, Inc. All rights reserved.

2
PM-20
DANGER / WARNINGS
Complete Grounding of this unit is necessary for the safe
operation of this equipment. Disconnect inputs before un-
grounding this equipment

3
PM-20
DANGER / WARNINGS
GENERAL SAFETY PRECAUTIONS


HIGH VOLTAGE
This equipment is capable of providing POTENTIALLY LETHAL VOLTAGES!
Improper operation or test practices may result in injury or death to the operator or
surrounding personnel.
The operation of High Voltage test equipment should only be performed by person-
nel familiar with HIGH VOLTAGE testing and safety procedures. The operator of this
equipment must be aware of all hazards associated with High Voltage testing. The
operator is responsible for himself and others in close proximity of the testing area.
Some General Safety Practices for working with High Voltage Test Equipment have
been listed below for your reference.
Become familiar with your instrument before performing an actual test
Know your work area, check that all circuits are de-energized and locked out.
Never work alone; always work with another qualified worker.
Mark off entire work area with barriers and warning tape.
Make all personnel aware of your testing activities.
Be aware of dangerous conditions that may arise from energizing a test spe-
cimen.
Never modify test equipment; modifications to equipment could introduce an
unknown hazard or hinder a designed-in safety feature.
DO NOT operate damaged equipment. Remove power, and do not use the
equipment until safe operation can be verified by service-trained personnel.
Phenix Technologies, Inc. assumes no liability for unsafe or improper use of test equip-
ment.

4
PM-20
PM-20 Safety Warnings
Before using this instrument, this manual and Safety Warnings must be read and understood.
Observe Safety procedures and rules for working near high voltage energized systems during the use of
this equipment. The generated voltages may be dangerous.
Do not connect or disconnect the test leads during the measurement.
Do not touch the acrylic cover of the galvanometer with the energized terminals. This could cause a static
charge that will affect all the measurements.
Be careful not to make a short-circuit between the high voltage terminals and the “-R” or “Guard” terminals
while a measurement is running. It may be dangerous for the operator and the output fuse may blow-up.
Be sure that there is not any voltage difference between the points to which the insulation tester will be
connected to, or between them and ground.
The panel, terminals, and connectors of the equipment must stay dry and clean.
This equipment should be used only by a trained and competent person, strictly applying suitable
safety rules.
Symbols Used
Caution, risk of electric shock.
Caution, refer to User Guide.
Equipment complies with current EU Directives.
The rubbish bin with a line through it means that in the European Union,
the product must undergo selective disposal for the recycling of electric
and electronic material, in compliance with Directive WEEE 2002/96/EC.

5
PM-20
TABLE OF CONTENTS
1. Description......................................................................6
2. Measurements.................................................................7
2.1. Control Panel ............................................................7
3. Power Supply..................................................................8
3.1. Checking Battery Status............................................8
3.2. Battery Charger.........................................................8
4. High Voltage Indicator.....................................................9
5. Operating Instructions ...................................................10
6. Polarization Index (PI)...................................................12
7. Infinite Setting ...............................................................12
8. Replacement Fuse........................................................13
9. Cleaning........................................................................13
10. Technical Specifications..............................................14
11. Application Note 32.....................................................15

6
PM-20
1. Description
The PM-20 high-voltage insulation tester is a truly portable device that allows measurements of insulation
resistances using test voltages up to 20kV. It employs state-of-the-art technology for safe measurements of
insulation resistances up to 4,000,000 MΩwith 4 test voltages: 5kV - 10 kV - 15 kV - 20 kV.
Readings are performed through an easy-to-read analogue indicator, having a broad scale. This equipment
is especially well suited to test insulation resistances in transmission lines and medium voltage distribution
systems, whether aerial or underground, as it performs testing with voltages near to the operational value. It
is an excellent auxiliary when detecting cable failures.
In order to maximize the operator’s safety, this equipment was made within a plastic cabinet of high dielectric
strength. A light indicator warns about dangerous voltages present, both in the equipment and in the element
under testing, and switches off only when the discharge process has finished.
This equipment has a GUARD terminal that allows avoidance of the effects of parasitic resistances and sur-
face currents on the insulation resistances under test. Due to its compact size and reduced weight, mechani-
cal strength, and self-contained battery supply, this apparatus is particularly suitable for field tests under
severe environments. It is easily carried, very simple to operate, and stands severe handling conditions.
Those harsh conditions include frequent shocks, extreme temperatures, vibrations during transportation on
rough roads, long direct exposure to solar radiation, dust, sand and other air-borne impurities, etc. Accuracy
is not affected by all these adverse conditions, and it is still comparable with that of the best laboratory in-
struments.

7
PM-20
2. Measurements
2.1 Control Panel
1. POWER INPUT.
2. FUSE.
3. 20 kV TEST VOLTAGE.
4. 15 kV TEST VOLTAGE.
5. 10 kV TEST VOLTAGE.
6. 5 kV TEST VOLTAGE.
7. CURRENT RETURN terminal (-R).
8. GUARD terminal (G).
9. ANALOG indicator.
10. MECHANICAL ADJUST (INFINITE).
11. ON indicator.
12. HIGH VOLTAGE indicator.
13. Key board RANGE (A, B, C & Cx10).
14. BATTERY CHARGER indicator.
15. BATTERY CHECK key.
16. ON/OFF switch.
17. START key.
18. STOP key.
9
3
4
5
6
7
8
10
2
1
12
22
2
14
13
18
17
15
16
11
1

8
PM-20
3. Power Supply
Internal rechargeable 12V - 7Ah battery.
1.1. Checking battery status
Battery measurement can be performed without interrupting high-voltage generation, which provides a better
evaluation of the battery status, by pressing the BATTERY CHECK during the measurement. The battery
test is performed under actual consumption conditions and, for long lasting measurements, (i.e. Polarization
Index), the battery status can be checked without affecting the measurement. The meter pointer should stop
over the blue zone. If the pointer stops over the red zone, the battery is discharged and must be charged.
1.2. Battery charger
This equipment has an intelligent built-in circuit that controls the battery charge and doesn’t allow the equip-
ment to operate during the charging process. To charge the battery, follow this procedure:
Verify that the On/Off switch is in OFF.
Connect the equipment to 220 –240 Vmains supply with power cord at the power input of the equip-
ment.
After a while, the battery charger indicator will blink alternatively in green and red during one sec-
ond, while the charger verifies the initial condition of the battery to select the optimized parameters of
the charge.
The following chart summarizes the meaning of battery charger LED:
Green and red flashing
alternatively
Test of the initial condition of the battery when plugging the mains, during one second.
Permanent red
Battery under charge.
Flashing red
Charging current is less than normal.
Permanent green
The charging process has been successfully finished. Battery OK.
Flashing green
The charging process has finished, nevertheless the battery hasn’t received the complete
charge.
At the end of battery useful life, the battery must be recycled or disposed of properly, in order to
protect the environment.
The rechargeable battery has no “memory effect” and there are no restrictions to start charging it as
many times as is needed. However, the battery could be damaged if it remains in deep discharge for
long periods.
To avoid this effect, charge the battery before storing the equipment, and recharge within 30 days, even
if the instrument was not used (under storage, the battery loses part of its charge).

9
PM-20
4. High Voltage Indicator
The High Voltage indicator warns the presence of high voltage at the output terminal
during a measurement and remains lit until the discharge process is completed. When
you press the STOP key, the equipment will start discharging the potentials accumulated
in the unit, internal capacitances, and in the element under test as well. When this dis-
charging process is over, the high voltage led will turn off automatically. The test leads
may then be disconnected.

10
PM-20
5. Operating Instructions
ATTENTION: For safe operation, the procedures detailed below should be carried out with the device
Powered-Off.
Check if there is no differences of potential voltage between the points where the equipment will be
connected to, nor between them and the ground.
1. Connect the red test lead to the 20 kV, 15 kV, 10 kV or 5 kV terminal in accordance with the desired test
voltage.
2. Connect the black test lead to the -R terminal.
(The test leads in the drawings are only for illustration.)
3. The green GUARD (G) terminal is not always used.

11
PM-20
Operating Instructions (Cont’d)
Technical Note 32 explains the use of GUARD (G) terminal in order to minimize the effect of stray re-
sistances. When measurement is carried out between parts where none of them is grounded, (like between
high-side and low-side windings of a transformer), GUARD terminal must be connected to ground in order
to fix the apparatus potential. At any time a measurement is performed, either the -R or GUARD termi-
nals must be connected to ground but never both simultaneously. If none of these terminals are con-
nected to ground, the insulation tester can reach a high potential that may result in an unstable, non-reliable
reading. If both terminals are simultaneously connected to ground, there is a short-circuit between
them, and consequently the insulation tester will measure with error.
NOTE: The insulation tester is unable to generate test voltage while it is connected to mains. The power
cable has to be unplugged from mains prior to pressing the Start button.
4. Turn On the apparatus by pressing the ON / OFF key. The ON led begins to brighten.
5. Press the Start key. The high-voltage generator starts operating and the corresponding indicator light
turns on at the front panel. The meter pointer will indicate the value of the unknown resistance. If the ele-
ment to be measured is strongly capacitive, it will initially indicate a low resistance value that will be grad-
ually increased while the charging of that capacitance takes place. The instrument will always begin in the
scale A.
6. When the measured resistance exceeds the maximum value in range A, press range Bkey, and if the
value is not achieved, press keys of ranges Cor C x 10, as required.
7. Always remember to multiply the reading by the factor stated in the following table, depending on selected
test voltage.
8. When key C x 10 is used, reading will be carried out in range Cand will be multiplied by 10, in addition to
the factor corresponding to the test voltage.
9. When you press the Stop key, the insulation tester will start discharging the potentials accumulated in the
unit’s internal capacitances and in those of the element under test as well. When this discharging process
is over (up to 60 seconds after turn off), the High voltage will turn off automatically. The test leads may
be disconnected. To finish measurement press On/Off switch.

12
PM-20
6. Polarization Index (PI)
For this type of test, the instrument must be connected and applying high voltage to the sample for 10
minutes. The polarization index is the ratio between the insulation resistance value measured after 10
minutes and the value measured after 1 minute.
7. Infinite Setting
The mechanical zero of galvanometer must be periodically checked. To perform this check, be sure that the
insulation tester is powered-off. The pointer should stay on the right end of the scale just over the infinite
mark on scale C. In other cases, the plastic screw at the bottom of the galvanometer acrylic cover shall be
adjusted.

13
PM-20
8. Replacement Fuse
To check the instrument Fuse, remove it with a screw driver. If the fuse is ruptured, replace it by another with
the following specifications:
Fuse Schurter, model SPT 5x20 (Time-lag) 2A/250V. High breaking capacity.
9. Cleaning
To clean this instrument, use a soft cleaning anti-static liquid, after verifying that it doesn’t affect the plastic
parts used in the case and in the Control Panel of this equipment.

14
PM-20
10. Technical Specifications
Test voltages
:
5 kV –10 kV –15 kV –20 kV
Insulation test up to
:
4,000,000 MΩ
Test
volt-
age
MEASURING INTERVALS (MΩ)
Scale
multi-
plier
Output
resist.
A
B
C
C x 10
5 kV
0 -
200
100 -
3.000
1.000 -
100.000
10.000 -
1.000.000
x1
10 MΩ
10 kV
0 -
400
200 -
6.000
2.000 -
200.000
20.000 -
2.000.000
x2
20 MΩ
15 kV
0 -
600
300 -
9.000
3.000 -
300.000
30.000 -
3.000.000
x3
30 MΩ
20 kV
0 -
800
400 -
12.000
4.000 -
400.000
40.000 -
4.000.000
x4
40 MΩ
Short-circuit current
:
500 µA
Test voltages accuracy
:
± 2% of nominal test voltages @ R ≥
10 GΩ
Insulation tester
accuracy
:
Class 2 (±2% of full scale deflection)
Analog indicator
:
Up to 98 mm scale length, taut band,
with mirror (thus avoiding parallax
errors)
Safety specifications
:
Electrical safety according to IEC
61010.
E.M.C.
:
In accordance with IEC 61326-1
Electrostatic immunity
:
In accordance with IEC 61000-4-2
Measurement category
:
CAT III –600 V.
Power supply
:
Internal rechargeable 12 V –7 Ah
battery
Battery charger
:
220 –240 Vmains supply.
Environmental
protection
:
IP54 (with closed lid)
Operating temperature
range
:
-5 C to +50 C
Storage temperature
range
:
-25 C to +65 C
Humidity range
:
95% RH (non condensing)
Weight
:
Approx. 9.8 kg
Dimensions
:
378 x 308 x 175 mm
Supplied accessories
:
2 measuring test leads (1.80 m).
GUARD test lead (1.80 m).
Charger power cord.
Carrying case
User’s guide.

15
PM-20
Application Note 32
Use of “Guard” terminal in insulation testers
When insulation resistance measurements are performed with insulation tester, especially with high sensitivi-
ty instruments measuring high resistance values, the use of the GUARD terminal avoids the harmful influ-
ence of stray resistances.
In order to better explain the function of this terminal, let us review the insulation tester basic circuit diagram
of fig. 1.
Where:
Vt : DC high-voltage generator
Ri : Generator internal resistance
A: Indicator meter (micro-ammeter)
The unknown resistance (Rx) is connected between +V and -R terminals. Its value determines the current
passing through the circuit, which in turn is indicated by the micro-ammeter. The value of Rx can be deter-
mined as follows:
In many cases the resistance to be measured is in parallel with other stray resistances which influence on Rx
should be minimized.
A typical example of this situation occurs when the insulation resistance between primary and secondary
windings of a transformer mounted inside a metal housing is to be measured.
Rx: Insulation resistance between primary and secondary winding.
R1: Insulation resistance between primary winding and housing.
R2: Insulation resistance between secondary winding and housing.

16
PM-20
If insulation tester (terminals V and R) is connected to transformer terminals A and B, and considering that
the resistance of the coils on each side of the transformer may be disregarded, Rx appears to be in parallel
with (R1 + R2). The situation is changed if we connect the transformer housing to GUARD terminal. Then the
circuit will be:
In the circuit of Fig. 3 it may be noted that R1 is in parallel with a low-value resistance (the one from the mi-
cro-ammeter), therefore its influence is reduced during reading.
Through resistance R2 circulates a current which is not passing through the meter and consequently does
not affect the reading. In fact, current through R2 originates a certain error, because it creates an additional
voltage drop in R1 which was not regarded during insulation tester calibration.
As regards the practical use of insulation tester, it will be considered that if R1 and R2 are higher than 100
MΩ, any value of Rx will be measured with an error lower than 10%. For example: Let us consider Rx =
3,000 MΩand R1 = R2 = 100 MΩ, the reading without using the GUARD terminal would be 187.5 MΩ, which
is quite wrong. On the other hand, if the GUARD terminal is properly used, we would have 3,000 MΩ, with an
error lower than 10%.