Phenomenex Zebron AG6-4110 User manual
Electronic Indicator
for Big Traps
Ordering Information
Zebron™ Gas Management Electronic Indicator
AG6-4110 Zebron Gas Management Electronic Indicator for Gas Trap, 1/pk
Reorder at www.phenomenex.com/GasManagement
Compliance
4. Maintenance
Terms and Conditions
+
+
The Low Battery Indicator
Icon displays when it is time
to replace the battery
Push the battery out
of the retainer with
the use of a pencil
shaped object
Slide the new battery
into the retainer
with the positive (+)
side of the battery
facing up
The Device or battery should not be placed in household
waste bins. Please check local regulations for information
about the disposal of electronic products in your area.
Push here Push here
Pull here
4.2 Replacing the Battery
4.3 Cleaning
Always remove the battery and/or the USB power source before clean-
ing the device. Not removing the battery before cleaning the device
can cause a short circuit and might destroy electronic components and
voids the manufacturers warranty.
Wipe the plastic casing with a slightly damp micro fiber or other soft,
lint-free cloth. Use a dry cloth or paint brush to whisk away dust from
the casing.
For removing dust on the electronics you could use compressed air
to blow away the dust. Never use water to clean the electronics as
this may damage the electronic parts of the device and cause a short
circuit.
Replace the battery annually or when the empty battery indicator icon is
active. When removing the battery or USB power source, the device will
still remember its last state, and once re-connected to a power source
it will continue from the state last known before the power source was
removed.
4.1 Opening the Device
Use a paperclip or similar
shaped tool to separate the
device from the clip
Detach the device from the clip if you need to replace the battery, or
when you would like to connect the device to your computer.
User Guide
IL67760419_W_4
4.4 Disposal
Patent Pending: PCT/NL2012/050477
Subject to Phenomenex Standard Terms and Conditions, which may
be viewed at www.phenomenex.com/TermsAndConditions.
Trademarks
Zebron is a trademark of Phenomenex.
FOR RESEARCH USE ONLY. Not for use in clinical diagnostic procedures.
© 2019 Phenomenex, Inc. All rights reserved.
REPLACE.
REORDER.
RELAX.
www.phenomenex.com
1. Quickstart
The Electronic Indicator is a monitoring device that alarms you when
planned maintenance or replacement for a consumable is due. Category Description
Power Requirements 3V CR2450 non-rechargeable
Lithium Coin Cell battery
Operating Temperature Range 0 ~ +48 (C)
Storage Temperature -10 ~ +55 (C)
Operating Humidity
10 percent to 80 percent relative
humidity, non-condensing
Storage Humidity 10 percent to 90 percent relative
humidity, non-condensing
Recommended Configured
Time Range 1 month ~ 3 years
Battery Lifetime approx. 1 year (with standby setting
enabled)
Communication Micro-B USB Connector
Warranty 2 Years factory warranty from the date
of purchase
Certifications CE , FCC
Compliance RoHS, WEEE
Safety Information
• There are no serviceable parts in this unit. Opening the
device—other than to change the battery—or tampering
with the internal parts will void the factory warranty.
• Not intended for outdoor use or wet locations.
• Always obtain prior authorization from your supervisor
before installing or using this device in controlled, hazard-
ous or restricted environments.
2. Installing the Device
Always ensure that the consumable or surface onto which you are
mounting the device will never exceed the operating temperature
limits as described in the specifications.
Technical Specifications
Overview
Numeric Display
Micro USB Communication Port
Tri-color LED
Bar Display
Buzzer
Battery
AG6-4110
For manual configuration, download and install the
latest version of the configuration software utility at
www.phenomenex.com/GasManagement and connect
the device to your computer with a Micro USB cable.
The default configured maintenance interval of the device is factory set
to 18 months. However it is recommended that you use a shorter interval
time that matches with your system maintenance schedule and/or sample
workload.
1.2 Default Device Settings
1.3 Manual Configuration
Pull battery
protection tab out
Clip the device (AG6-4110) onto the Big Trap as shown in the
illustration below.
Battery Storage and Handling
www.phenomenex.com/GasManagement
For Zebron™ Big Traps, the following model should be used.
The battery is pre-installed into the device and disabled by a battery
protection tab. To initialize (start) the device with its default settings pull
the battery protection tab out.
1.1 Enabling the Device
Note: the default notification settings can be adjusted with the configuration
utility.
Electronic Indicator
with Clip for
Big Trap
100 - 21 %
Orange
20 - 10 % 9 - 0 %
Red
3 - 0 %
Red + Buzzer
3. Resetting the Device
For resetting the device, download and install the latest version of
the configuration software utility at www.phenomenex.com/GasMa-
nagement and connect the device to your computer with a Micro
USB cable.
• Do not swallow the battery. Keep this device out of reach
of children. Lithium coin cells can cause serious injury or
death if swallowed.
• Do not try to open the battery and do not burn the battery
in fire. Exposure to the ingredients contained within or
their combustion products could be harmful.
• Do not short-circuit battery. Short-circuiting the battery
may cause leakage and high heat which can cause burns.
• Only remove the battery protection tab when you start
using the device. When you are not using the device
remove the battery and store it in a dry and secure place
away from other batteries or heat sources and out of
reach of children.
1. Quickstart
The Electronic Indicator is a monitoring device that alarms you when
planned maintenance or replacement for a consumable is due. Category Description
Power Requirements 3V CR2450 non-rechargeable
Lithium Coin Cell battery
Operating Temperature Range 0 ~ +48 (C)
Storage Temperature -10 ~ +55 (C)
Operating Humidity
10 percent to 80 percent relative
humidity, non-condensing
Storage Humidity 10 percent to 90 percent relative
humidity, non-condensing
Recommended Configured
Time Range 1 month ~ 3 years
Battery Lifetime approx. 1 year (with standby setting
enabled)
Communication Micro-B USB Connector
Warranty 2 Years factory warranty from the date
of purchase
Certifications CE , FCC
Compliance RoHS, WEEE
Safety Information
• There are no serviceable parts in this unit. Opening the
device—other than to change the battery—or tampering
with the internal parts will void the factory warranty.
• Not intended for outdoor use or wet locations.
• Always obtain prior authorization from your supervisor
before installing or using this device in controlled, hazard-
ous or restricted environments.
2. Installing the Device
Always ensure that the consumable or surface onto which you are
mounting the device will never exceed the operating temperature
limits as described in the specifications.
Technical Specifications
Overview
Numeric Display
Micro USB Communication Port
Tri-color LED
Bar Display
Buzzer
Battery
AG6-4110
For manual configuration, download and install the
latest version of the configuration software utility at
www.phenomenex.com/GasManagement and connect
the device to your computer with a Micro USB cable.
The default configured maintenance interval of the device is factory set
to 18 months. However it is recommended that you use a shorter interval
time that matches with your system maintenance schedule and/or sample
workload.
1.2 Default Device Settings
1.3 Manual Configuration
Pull battery
protection tab out
Clip the device (AG6-4110) onto the Big Trap as shown in the
illustration below.
Battery Storage and Handling
www.phenomenex.com/GasManagement
For Zebron™ Big Traps, the following model should be used.
The battery is pre-installed into the device and disabled by a battery
protection tab. To initialize (start) the device with its default settings pull
the battery protection tab out.
1.1 Enabling the Device
Note: the default notification settings can be adjusted with the configuration
utility.
Electronic Indicator
with Clip for
Big Trap
100 - 21 %
Orange
20 - 10 % 9 - 0 %
Red
3 - 0 %
Red + Buzzer
3. Resetting the Device
For resetting the device, download and install the latest version of
the configuration software utility at www.phenomenex.com/GasMa-
nagement and connect the device to your computer with a Micro
USB cable.
• Do not swallow the battery. Keep this device out of reach
of children. Lithium coin cells can cause serious injury or
death if swallowed.
• Do not try to open the battery and do not burn the battery
in fire. Exposure to the ingredients contained within or
their combustion products could be harmful.
• Do not short-circuit battery. Short-circuiting the battery
may cause leakage and high heat which can cause burns.
• Only remove the battery protection tab when you start
using the device. When you are not using the device
remove the battery and store it in a dry and secure place
away from other batteries or heat sources and out of
reach of children.
1. Quickstart
The Electronic Indicator is a monitoring device that alarms you when
planned maintenance or replacement for a consumable is due. Category Description
Power Requirements 3V CR2450 non-rechargeable
Lithium Coin Cell battery
Operating Temperature Range 0 ~ +48 (C)
Storage Temperature -10 ~ +55 (C)
Operating Humidity
10 percent to 80 percent relative
humidity, non-condensing
Storage Humidity 10 percent to 90 percent relative
humidity, non-condensing
Recommended Configured
Time Range 1 month ~ 3 years
Battery Lifetime approx. 1 year (with standby setting
enabled)
Communication Micro-B USB Connector
Warranty 2 Years factory warranty from the date
of purchase
Certifications CE , FCC
Compliance RoHS, WEEE
Safety Information
• There are no serviceable parts in this unit. Opening the
device—other than to change the battery—or tampering
with the internal parts will void the factory warranty.
• Not intended for outdoor use or wet locations.
• Always obtain prior authorization from your supervisor
before installing or using this device in controlled, hazard-
ous or restricted environments.
2. Installing the Device
Always ensure that the consumable or surface onto which you are
mounting the device will never exceed the operating temperature
limits as described in the specifications.
Technical Specifications
Overview
Numeric Display
Micro USB Communication Port
Tri-color LED
Bar Display
Buzzer
Battery
AG6-4110
For manual configuration, download and install the
latest version of the configuration software utility at
www.phenomenex.com/GasManagement and connect
the device to your computer with a Micro USB cable.
The default configured maintenance interval of the device is factory set
to 18 months. However it is recommended that you use a shorter interval
time that matches with your system maintenance schedule and/or sample
workload.
1.2 Default Device Settings
1.3 Manual Configuration
Pull battery
protection tab out
Clip the device (AG6-4110) onto the Big Trap as shown in the
illustration below.
Battery Storage and Handling
www.phenomenex.com/GasManagement
For Zebron™ Big Traps, the following model should be used.
The battery is pre-installed into the device and disabled by a battery
protection tab. To initialize (start) the device with its default settings pull
the battery protection tab out.
1.1 Enabling the Device
Note: the default notification settings can be adjusted with the configuration
utility.
Electronic Indicator
with Clip for
Big Trap
100 - 21 %
Orange
20 - 10 % 9 - 0 %
Red
3 - 0 %
Red + Buzzer
3. Resetting the Device
For resetting the device, download and install the latest version of
the configuration software utility at www.phenomenex.com/GasMa-
nagement and connect the device to your computer with a Micro
USB cable.
• Do not swallow the battery. Keep this device out of reach
of children. Lithium coin cells can cause serious injury or
death if swallowed.
• Do not try to open the battery and do not burn the battery
in fire. Exposure to the ingredients contained within or
their combustion products could be harmful.
• Do not short-circuit battery. Short-circuiting the battery
may cause leakage and high heat which can cause burns.
• Only remove the battery protection tab when you start
using the device. When you are not using the device
remove the battery and store it in a dry and secure place
away from other batteries or heat sources and out of
reach of children.
1. Quickstart
The Electronic Indicator is a monitoring device that alarms you when
planned maintenance or replacement for a consumable is due. Category Description
Power Requirements 3V CR2450 non-rechargeable
Lithium Coin Cell battery
Operating Temperature Range 0 ~ +48 (C)
Storage Temperature -10 ~ +55 (C)
Operating Humidity
10 percent to 80 percent relative
humidity, non-condensing
Storage Humidity 10 percent to 90 percent relative
humidity, non-condensing
Recommended Configured
Time Range 1 month ~ 3 years
Battery Lifetime approx. 1 year (with standby setting
enabled)
Communication Micro-B USB Connector
Warranty 2 Years factory warranty from the date
of purchase
Certifications CE , FCC
Compliance RoHS, WEEE
Safety Information
• There are no serviceable parts in this unit. Opening the
device—other than to change the battery—or tampering
with the internal parts will void the factory warranty.
• Not intended for outdoor use or wet locations.
• Always obtain prior authorization from your supervisor
before installing or using this device in controlled, hazard-
ous or restricted environments.
2. Installing the Device
Always ensure that the consumable or surface onto which you are
mounting the device will never exceed the operating temperature
limits as described in the specifications.
Technical Specifications
Overview
Numeric Display
Micro USB Communication Port
Tri-color LED
Bar Display
Buzzer
Battery
AG6-4110
For manual configuration, download and install the
latest version of the configuration software utility at
www.phenomenex.com/GasManagement and connect
the device to your computer with a Micro USB cable.
The default configured maintenance interval of the device is factory set
to 18 months. However it is recommended that you use a shorter interval
time that matches with your system maintenance schedule and/or sample
workload.
1.2 Default Device Settings
1.3 Manual Configuration
Pull battery
protection tab out
Clip the device (AG6-4110) onto the Big Trap as shown in the
illustration below.
Battery Storage and Handling
www.phenomenex.com/GasManagement
For Zebron™ Big Traps, the following model should be used.
The battery is pre-installed into the device and disabled by a battery
protection tab. To initialize (start) the device with its default settings pull
the battery protection tab out.
1.1 Enabling the Device
Note: the default notification settings can be adjusted with the configuration
utility.
Electronic Indicator
with Clip for
Big Trap
100 - 21 %
Orange
20 - 10 % 9 - 0 %
Red
3 - 0 %
Red + Buzzer
3. Resetting the Device
For resetting the device, download and install the latest version of
the configuration software utility at www.phenomenex.com/GasMa-
nagement and connect the device to your computer with a Micro
USB cable.
• Do not swallow the battery. Keep this device out of reach
of children. Lithium coin cells can cause serious injury or
death if swallowed.
• Do not try to open the battery and do not burn the battery
in fire. Exposure to the ingredients contained within or
their combustion products could be harmful.
• Do not short-circuit battery. Short-circuiting the battery
may cause leakage and high heat which can cause burns.
• Only remove the battery protection tab when you start
using the device. When you are not using the device
remove the battery and store it in a dry and secure place
away from other batteries or heat sources and out of
reach of children.
Electronic Indicator
for Big Traps
Ordering Information
Zebron™ Gas Management Electronic Indicator
AG6-4110 Zebron Gas Management Electronic Indicator for Gas Trap, 1/pk
Reorder at www.phenomenex.com/GasManagement
Compliance
4. Maintenance
Terms and Conditions
+
+
The Low Battery Indicator
Icon displays when it is time
to replace the battery
Push the battery out
of the retainer with
the use of a pencil
shaped object
Slide the new battery
into the retainer
with the positive (+)
side of the battery
facing up
The Device or battery should not be placed in household
waste bins. Please check local regulations for information
about the disposal of electronic products in your area.
Push here Push here
Pull here
4.2 Replacing the Battery
4.3 Cleaning
Always remove the battery and/or the USB power source before clean-
ing the device. Not removing the battery before cleaning the device
can cause a short circuit and might destroy electronic components and
voids the manufacturers warranty.
Wipe the plastic casing with a slightly damp micro fiber or other soft,
lint-free cloth. Use a dry cloth or paint brush to whisk away dust from
the casing.
For removing dust on the electronics you could use compressed air
to blow away the dust. Never use water to clean the electronics as
this may damage the electronic parts of the device and cause a short
circuit.
Replace the battery annually or when the empty battery indicator icon is
active. When removing the battery or USB power source, the device will
still remember its last state, and once re-connected to a power source
it will continue from the state last known before the power source was
removed.
4.1 Opening the Device
Use a paperclip or similar
shaped tool to separate the
device from the clip
Detach the device from the clip if you need to replace the battery, or
when you would like to connect the device to your computer.
User Guide
IL67760419_W_4
4.4 Disposal
Patent Pending: PCT/NL2012/050477
Subject to Phenomenex Standard Terms and Conditions, which may
be viewed at www.phenomenex.com/TermsAndConditions.
Trademarks
Zebron is a trademark of Phenomenex.
FOR RESEARCH USE ONLY. Not for use in clinical diagnostic procedures.
© 2019 Phenomenex, Inc. All rights reserved.
REPLACE.
REORDER.
RELAX.
www.phenomenex.com
Electronic Indicator
for Big Traps
Ordering Information
Zebron™ Gas Management Electronic Indicator
AG6-4110 Zebron Gas Management Electronic Indicator for Gas Trap, 1/pk
Reorder at www.phenomenex.com/GasManagement
Compliance
4. Maintenance
Terms and Conditions
+
+
The Low Battery Indicator
Icon displays when it is time
to replace the battery
Push the battery out
of the retainer with
the use of a pencil
shaped object
Slide the new battery
into the retainer
with the positive (+)
side of the battery
facing up
The Device or battery should not be placed in household
waste bins. Please check local regulations for information
about the disposal of electronic products in your area.
Push here Push here
Pull here
4.2 Replacing the Battery
4.3 Cleaning
Always remove the battery and/or the USB power source before clean-
ing the device. Not removing the battery before cleaning the device
can cause a short circuit and might destroy electronic components and
voids the manufacturers warranty.
Wipe the plastic casing with a slightly damp micro fiber or other soft,
lint-free cloth. Use a dry cloth or paint brush to whisk away dust from
the casing.
For removing dust on the electronics you could use compressed air
to blow away the dust. Never use water to clean the electronics as
this may damage the electronic parts of the device and cause a short
circuit.
Replace the battery annually or when the empty battery indicator icon is
active. When removing the battery or USB power source, the device will
still remember its last state, and once re-connected to a power source
it will continue from the state last known before the power source was
removed.
4.1 Opening the Device
Use a paperclip or similar
shaped tool to separate the
device from the clip
Detach the device from the clip if you need to replace the battery, or
when you would like to connect the device to your computer.
User Guide
IL67760419_W_4
4.4 Disposal
Patent Pending: PCT/NL2012/050477
Subject to Phenomenex Standard Terms and Conditions, which may
be viewed at www.phenomenex.com/TermsAndConditions.
Trademarks
Zebron is a trademark of Phenomenex.
FOR RESEARCH USE ONLY. Not for use in clinical diagnostic procedures.
© 2019 Phenomenex, Inc. All rights reserved.
REPLACE.
REORDER.
RELAX.
www.phenomenex.com
Electronic Indicator
for Big Traps
Ordering Information
Zebron™ Gas Management Electronic Indicator
AG6-4110 Zebron Gas Management Electronic Indicator for Gas Trap, 1/pk
Reorder at www.phenomenex.com/GasManagement
Compliance
4. Maintenance
Terms and Conditions
+
+
The Low Battery Indicator
Icon displays when it is time
to replace the battery
Push the battery out
of the retainer with
the use of a pencil
shaped object
Slide the new battery
into the retainer
with the positive (+)
side of the battery
facing up
The Device or battery should not be placed in household
waste bins. Please check local regulations for information
about the disposal of electronic products in your area.
Push here Push here
Pull here
4.2 Replacing the Battery
4.3 Cleaning
Always remove the battery and/or the USB power source before clean-
ing the device. Not removing the battery before cleaning the device
can cause a short circuit and might destroy electronic components and
voids the manufacturers warranty.
Wipe the plastic casing with a slightly damp micro fiber or other soft,
lint-free cloth. Use a dry cloth or paint brush to whisk away dust from
the casing.
For removing dust on the electronics you could use compressed air
to blow away the dust. Never use water to clean the electronics as
this may damage the electronic parts of the device and cause a short
circuit.
Replace the battery annually or when the empty battery indicator icon is
active. When removing the battery or USB power source, the device will
still remember its last state, and once re-connected to a power source
it will continue from the state last known before the power source was
removed.
4.1 Opening the Device
Use a paperclip or similar
shaped tool to separate the
device from the clip
Detach the device from the clip if you need to replace the battery, or
when you would like to connect the device to your computer.
User Guide
IL67760419_W_4
4.4 Disposal
Patent Pending: PCT/NL2012/050477
Subject to Phenomenex Standard Terms and Conditions, which may
be viewed at www.phenomenex.com/TermsAndConditions.
Trademarks
Zebron is a trademark of Phenomenex.
FOR RESEARCH USE ONLY. Not for use in clinical diagnostic procedures.
© 2019 Phenomenex, Inc. All rights reserved.
REPLACE.
REORDER.
RELAX.
www.phenomenex.com
Table of contents
Other Phenomenex Measuring Instrument manuals
