Philips Avent SCF393/61 User manual

Single/Double
Electric Breast Pump
Advanced
SCF393/61
SCF391/61
www.philips.com/mybreastpump

Foldout left only

D
C
B
A
C
B
A
B1
B2
B3
B4
B5
B6
C5
C3 C4
C2
C1
A1
A2
A3
A4
A5
D7
D1 D3 D5
D4 D6
D8
D2

emtypageinsideco
ver

English
5
English
English
Contents
Introduction __________________________________________________________________________________________ 5
General description __________________________________________________________________________________ 6
Indications for use____________________________________________________________________________________ 7
Important safety information ________________________________________________________________________ 7
Before first use _______________________________________________________________________________________ 11
Cleaning and disinfecting ____________________________________________________________________________ 11
Using the breast pump _______________________________________________________________________________ 15
Using the breast pump when you have symptoms of engorgement _______________________________ 19
After use ______________________________________________________________________________________________ 19
Feeding breast milk with the bottle__________________________________________________________________ 21
Compatibility _________________________________________________________________________________________ 23
Ordering accessories _________________________________________________________________________________ 23
Disposal_______________________________________________________________________________________________ 23
Full Two-Year Warranty ______________________________________________________________________________ 23
Troubleshooting ______________________________________________________________________________________ 23
Undesirable side effects _____________________________________________________________________________ 25
Storage conditions ___________________________________________________________________________________ 25
Electromagnetic fields (EMF) ________________________________________________________________________ 25
Technical information ________________________________________________________________________________ 26
Explanation of symbols ______________________________________________________________________________ 29
Introduction
Congratulations on your purchase and welcome to Philips Avent! To fully benefit from the support
that Philips Avent offers, register your breast pump at www.philips.com/welcome.
The Philips Avent single/double electric breast pump Advanced is inspired by babies and their natural
suction movement. The soft silicone cushion stimulates the nipple with gentle massaging movements,
helping you to express milk comfortably and effectively. The combination of suction and nipple
stimulation triggers fast milk flow. The no-lean-forward design enables you to sit in a relaxed, upright
position while expressing.
To breastfeed longer, you can express and store your milk so that your baby can still enjoy the
benefits of it, even if you cannot be there to provide it yourself. As the pump is compact, quiet and
discrete to use, you can take it with you anywhere, allowing you to express milk at your own
convenience and to maintain your milk supply.
If breastfeeding goes well, it is advisable (unless recommended otherwise by your healthcare
professional) to wait until your milk supply and breastfeeding schedule are established (normally at
least 2 to 4 weeks after giving birth) before you start expressing.

6English
General description
Note: The numbers mentioned below refer to the numbers on the figure of the front foldout page
of this user manual.
Note: The single breast pump (SCF391/61) includes one set and the double breast pump
(SCF393/61) includes two sets of the breast pump kit and Philips Avent Natural bottle shown in
Figures B andC.
Product description (Fig. A)
A1 Motor unit
A2 Breast pump kit
A3 Bottle
A4 Adapter*
A5 Double breast pump
* The adapter supplied may vary for different
countries.
Breast pump kit (Fig. B)
B1 Silicone tube and cap
B2 Silicone diaphragm
B3 Pump body
B4 Cover
B5 Cushion
B6 White valve
Philips Avent Natural bottle (Fig. C)
C1 Bottle cap
C2 Screw ring
C3 Feeding nipple
C4 Sealing disc
C5 Bottle
Motor unit part description (Fig. D)
D1 USB power inlet
D2 On/off button with pause/play function
D3 Mode selection button
D4 'Level down' button
D5 'Level up' button
D6 Indicator lights for modes and levels
D7 Tubing port for single breast pump
D8 Tubing ports for double breast pump
Accessories
There are multiple versions of this breast pump package, which all come with a different combination
of the following Philips Avent accessories:
-Breast pads
-Travel bag
-Insulation pouch
-Cleaning brush
-Storage cups with adapter*
-Breast milk storage bags*
-Natural bottles
* For these accessories, a separate user manual is provided.

7
English
English
Indications for use
The Philips Avent single/double electric breast pump Advanced is intended to express and collect
milk from the breast of a lactating woman, and to alleviate engorgement of the breast. Thedevice is
intended for a single user.
Important safety information
Read this user manual carefully before you use the breast pump and save it for future reference.
This user manual can also be found online on the Philips Avent website: www.philips.com/avent.
This product is operated by the lactating woman herself.
You can use this breast pump in an everyday environment.
Contraindications
- Never use the breast pump while you are pregnant, as pumping
can induce labor.
Warnings
Warnings to avoid choking, strangulation and injury:
- Do not allow children or pets to play with the motor unit, the
adapter, packaging materials or accessories.
- Always unplug the breast pump after use. Store the breast
pump when not in use.
-This breast pump is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge. Such persons can only use this
breast pump if they are supervised by or have received proper
instruction concerning use of the appliance by a person
responsible for their safety.
Warning to prevent transmitting infectious diseases:
-If you are a mother who is infected with Hepatitis B, Hepatitis C or
Human Immunodeficiency Virus (HIV), expressing breast milk will
not reduce or remove the risk of transmitting the virus to your
baby through your breast milk.

8English
Warnings to avoid electric shock:
-Inspect the breast pump, including the adapter, for signs of
damage before each use. Do not use the breast pump if the
adapter or plug is damaged, if it does not work properly or if it has
been dropped or submerged in water.
-If the power adapter outer casings become loose or are
separating, contact the device manufacturer immediately.
Separation of the casing can result in electric shock.
-Only use the adapter (S009AHz050yyyy) provided with this
breast pump.
-Always ensure that it is easy to disconnect the device from the
mains in case of malfunction. The adapter is considered the
disconnection device.
Warnings to avoid contamination and to ensure hygiene:
-For hygienic reasons, the breast pump is only intended for
repeated use by a single user.
-Clean and disinfect all parts before first use and after each use.
-Do not use antibacterial or abrasive cleaning agents to clean the
breast pump parts as this may cause damage.
-Wash your hands thoroughly with soap and water before you
touch breast pump parts and breasts to prevent contamination.
Avoid touching the inside of containers or lids.
Warnings to avoid breast and nipple problems including pain:
-Do not use the breast pump if the silicone diaphragm appears to
be damaged or broken. See chapter ‘Ordering accessories’ for
information on how to obtain replacement parts.
-Only use accessories and parts recommended by Philips Avent.
-There are no user serviceable parts inside the motor unit of the
breast pump.
-No modification of the breast pump is allowed. If you do so, your
warranty becomes invalid.
-Never use the breast pump while you are sleepy or drowsy to
avoid lack of attention during use.

9
English
English
-Always switch off the breast pump before you remove the pump
body from your breast, in order to release the vacuum.
-If the vacuum is uncomfortable or causes pain, switch off and
remove the breast pump from your breast.
-Do not continue pumping for more than five minutes at a time if
you do not succeed in expressing any milk. Try to express at
another time during the day.
-If the process becomes very uncomfortable or painful, stop using
the pump and consult your healthcare professional.
Warnings to prevent damage and malfunction of the breast pump:
-Portable radio frequency (RF) communications equipment
(including mobile phones and peripherals such as antenna cables
and external antennas) should not be used closer than 30cm
(12in) to any part of the breast pump, including adapter. This
could have a negative effect on the performance of the breast
pump.
-Use of this equipment adjacent to or stacked with other
equipment should be avoided because it could result in improper
operation.
Warnings to avoid increased electromagnetic emissions or
decreased electromagnetic immunity of this device, resulting in
improper operation:
-Do not use any other adapter or charging cable than supplied
with the device.
-Use of accessories, transducers and cables other than those
specified or provided by the manufacturer of this equipment
could result in increased electromagnetic emissions or decreased
electromagnetic immunity of this equipment and result in
improper operation.

10 English
Cautions
Cautions to prevent damage to and malfunctioning of the breast
pump:
-Prevent the adapter and motor unit from coming into contact with
water.
-Never put the motor unit or the adapter in water or in a
dishwasher, as this causes permanent damage to these parts.
-Keep the adapter and the silicone tubes away from heated
surfaces to avoid overheating and deformation of these parts.
SAVE THESE INSTRUCTIONS.

11
English
English
Before first use
Disassemble, clean and disinfect all parts that come into contact with breast milk before you use the
breast pump for the first time and after every use.
Cleaning and disinfecting
Overview
Clean and disinfect the parts that come into contact with the breast and breast milk as described
below:
When How
Clean and disinfect before first use
and after every use.*
Disassemble all parts and then
clean them as described in chapter
'Cleaning' and disinfect them as
described in chapter 'Disinfecting'.
* Note: Disinfecting is especially important if your baby is less than 3months old, was born
prematurely, or has a weakened immune system due to illness or medical treatment. To ensure
hygiene, perform the disinfecting step at least once a day.
The following parts do not come into contact with the breast and breast milk; clean them as described
below:
When How
Clean when needed.
Wipe with a clean, damp cloth with
water and mild detergent. Wipe the
motor unit with a clean, soft cloth
moistened with low-level
disinfectant such as ethyl or
isopropyl alcohol (70-90%).
Do not disinfect the tube.
Caution: Inspect the tubing. If you find condensation in the air tube, wash and dry it immediately
or replace the tubing. If you see breast milk inside the tubing or tubing connector, do not attempt to
wash, clean or disinfect the tubing or tubing connector. Instead, contact the manufacturer.

12 English
Step 1: Disassembling
Disassemble the breast pump, bottle and storage cup completely.
Also remove the white valve from the breast pump.
Step 2: Cleaning
The parts that come in contact with milk can be cleaned manually or in the dishwasher.
Warning: Do not use antibacterial or abrasive cleaning agents to clean the breast
pump parts as this may cause damage.
Caution: Never put the motor unit or the adapter in water or in a dishwasher, as this
causes permanent damage to these parts.
Caution: Be careful when you remove and clean the white valve. If it gets damaged,
your breast pump does not function properly. To remove the white valve, gently pull at
the ribbed tab on the side of the valve. To clean the white valve, rub it gently between
your fingers in warm water with some dishwashing liquid. Do not insert objects into the
white valve, as this may cause damage.

13
English
English
Step 2A: Manual cleaning
Supplies needed:
-Mild dishwashing liquid
-Drinking-quality water
-Soft, clean brush used only for infant feeding
items
-Clean tea towel or drying rack
-Clean bowl used only for infant feeding
items
1. Rinse all parts under
a running tap with
lukewarm water. Do not
place the parts in a sink
to rinse.
5 min.
2. Soak all parts for
5minutes in warm
water with some mild
dishwashing liquid.
3. Clean all parts with a
cleaning brush.
4. Thoroughly rinse all
parts under a running
tap with cold clear
water by holding them.
Clean the bowl and the
brush. Rinse them well
and allow them to air-
dry after each use.
Wash them by hand or
in a dishwasher at least
every few days.
5. Leave all parts to air-
dry on a clean, unused
tea towel or drying rack
in an area protected
from dirt and dust. Do
not use a tea towel to
rub or to pat the items
dry.
Step 2B: Cleaning in the dishwasher
Supplies needed:
-Mild dishwashing liquid or a dishwashing tablet
-Drinking-quality water
Note: Food colorings may discolor parts.

14 English
1. Place all parts on the
top rack of the
dishwasher.
2. Put dishwashing
liquid or a tablet in the
machine. Run a
standard program using
hot water and a heated
drying cycle (or
sanitizing setting).
3. Remove the parts
from dishwasher with
clean hands. If items
are not completely dry,
place items on a clean,
unused tea towel or
paper towel to air-dry
thoroughly before
storing. Do not use a
tea towel to rub or pat
the items dry.
Step 3: Disinfecting
Supplies needed:
-A household pot
-Drinking-quality water
Caution: During disinfection with boiling water, prevent the bottle or other parts from
touching the side of the pot. This can cause irreversible product deformation or damage
that Philips cannot be held liable for.
5 min.
1. Fill a household pot
with enough water to
cover all parts and
place all parts in the
pot. Let the water boil
for 5minutes. Make
sure the parts do not
touch the side of the
pot.
2. Allow the water to
cool down.
3. Gently remove the
parts from the water.
Place the parts on a
clean surface/tea towel
or drying rack to air-dry.
4. Store the dry items
safely until needed.
Ensure the clean pump
parts, bottle brushes
and wash bowls have
air-dried thoroughly
before storing. Items
must be completely dry
to help prevent germs
and mold from growing.
Store the dry items in a
clean, protected area.

15
English
English
Using the breast pump
Cushion size
The Philips Avent single/double electric breast pump Advanced has a soft, active cushion. There is
only one cushion size. It gently stimulates your nipple to trigger milk flow. The cushion is made of
flexible silicone, fitting nipple sizes up to 30mm/1.18in.
Assembling the breast pump
Make sure you have cleaned and disinfected the parts of the breast pump that come into contact with
milk.
Warning: Be careful, when you have disinfected the breast pump parts by boiling
them, they can be very hot. To prevent burns, only start assembling the breast pump
when disinfected parts have cooled down.
Warning: Wash your hands thoroughly with soap and water before you touch breast
pump parts and breasts to prevent contamination. Avoid touching the inside of
containers or lids.
Caution: Before each use, visually inspect the individual components for cracks, chips, tears,
discoloration or deterioration. In the event that damage to the device is observed, discontinue use
until the parts have been replaced.
Caution: Inspect the tubing. If you find condensation in the air tube, wash and dry it immediately
or replace the tubing. If you see breast milk inside the tubing or tubing connector, do not attempt to
wash, clean or disinfect the tubing or tubing connector. Instead, contact the manufacturer.
Note: Correct placement of the cushion, silicone diaphragm and silicone tube is essential for the
breast pump to form a proper vacuum.
1. Wash your hands
thoroughly with soap
and water.
2. Push the white valve
in the pump body as far
as possible.
3. Screw the pump body
onto the bottle.
4. Place the cushion in
the pump body and
make sure that the rim
covers the pump body.

16 English
4A. Push the inner part
of the cushion into the
funnel against the line
(indicated with an
arrow).
5. Place the silicone
diaphragm in the pump
body.
5A. Make sure that the
silicone diaphragm fits
securely around the rim
by pressing it down with
your thumbs.
6. Attach the silicone
tube and cap onto the
silicone diaphragm.
Push down the cap
until it is securely in
place.
7. Connect the tube(s)
to the motor unit.
8. Insert the adapter
into the power outlet
and insert the small
plug at the other end
into the motor unit.
9. The breast pump is
now ready for use.
Note: You can place
the cover over the
cushion to keep the
breast pump clean
when you take it with
you and while you are
preparing for
expressing.
Motor unit part description
7
1 3 5
4 6
8
2
1 USB power inlet
2 On/off button with
pause/play function
3 Mode selection button
4 'Level down' button
5 'Level up' button
6 Indicator lights for modes
and levels
7 Tubing port for single
breast pump
8 Tubing ports for double
breast pump

17
English
English
Mode indicator lights
The breast pump has two modes. Below you find an explanation of these modes.
Indicator
lights
Mode Explanation No. of suction levels
Stimulation
mode
Mode to stimulate the breast to start
up the milk flow.
8 suction levels
Expression
mode
Mode for efficient milk removal after
milk has started flowing. After 90 sec. of
stimulation, the device automatically
switches to the expression mode.
16 suction levels
Note: When you change the suction level, the display shows the selected suction level for a few
seconds and then shows the selected mode again.
Suction level indicator lights
Suction level 1:
Bottom light
flashes
Suction level 2:
Bottom light
steady on
Suction level 3:
Bottom light
steady on +
next light
flashes
Suction level 4:
2 lights steady
on.
Suction level 5:
2 lights steady
on + next light
flashes.
Suction level
16: all lights are
on
Note: Every time the level increases, the next light starts flashing or the flashing light becomes solid.
Pumping instructions
Warning: Before you remove the pump body from your breast, always switch off the
breast pump to release the vacuum.
Warning: Do not continue pumping for more than 5 minutes at a time if you do not
succeed in expressing any milk. Try to express at another time during the day.
Warning: If the process becomes very uncomfortable or painful, stop using the pump
and consult your healthcare professional.
Caution: If discomfort is felt, then suction can be broken by inserting a finger between the breast
and the cushion.

18 English
Note: If you regularly express more than 125ml/4floz per session, you can purchase and use a
260ml/9floz Philips Avent Natural bottle to prevent overfilling and spillage.
1. Wash your hands
thoroughly with soap
and water and make
sure that your breast is
clean.
2. Place the breast
pump kit onto your
breast. Make sure that
you center your nipple.
3 sec.
3. Press and hold the
on/off button until the
device switches on. The
indicator lights go on to
indicate that the device
is in stimulation mode.
4. The breast pump
starts in stimulation
mode and slowly
increases its vacuum to
the last used
stimulation suction
level (or level 5 when
used for the first time).
5. Use the 'level up' and
'level down' buttons to
change the suction
level to your
preference.
90 sec.
6. After 90 seconds the
breast pump will switch
smoothly to expression
mode and slowly
increase its vacuum to
the last used
expression suction level
(or level 11 when used
for the first time).
7. If your milk starts
flowing earlier or if you
want to switch from
expression to
stimulation mode, you
can switch modes with
the mode selection
button.
8. Briefly press the
on/off button if you
want to pause. To
continue, briefly press
the on/off button
again.
3 sec.
9. Press and hold the
on/off button to switch
off.
10. Unplug the adapter
from the power outlet
and pull the small plug
out of the motor unit.
Tip: For optimal expression, choose the highest setting that still feels comfortable. This setting may
differ across different sessions.

19
English
English
Tip: You can use the double breast pump as a single breast pump by connecting only the tube of
one pump kit to the motor unit. 
Using the breast pump when you have symptoms
of engorgement
Breast engorgement means your breasts are overfilled with milk. This is a painful and unpleasant
condition. Frequent extraction of milk and completely emptying the breasts of milk can reduce
engorgement. When you have symptoms of engorgement, make sure you use a lower vacuum level to
minimize stretching of breast tissue.
Note: When symptoms of engorgement are present, make sure you empty your breasts completely
during each expression session.
After use
1. Unscrew the bottle. 2A. To store the breast
milk: close the bottle
with the sealing disc
and screw ring.
1
2
2B. To prepare the
bottle for feeding your
baby: place a nipple in
a screw ring and screw
the assembled screw
ring onto the bottle.
Seal the nipple with the
bottle cap (see
'Assembling the bottle').
3. Remove the silicone
tube and cap from the
breast pump kit.
4. Disassemble and
clean all parts that have
been in contact with
breast milk as soon as
possible after pumping
(see 'Cleaning and
disinfecting').
5. Clean the motor unit
with disinfection wipes.
For easy storage, wrap
the silicone tube
around the motor unit
and clip the cap onto
the tube.

20 English
Warning: Refrigerate or freeze expressed milk immediately, label with date and time,
or keep it at a room temperature of up to 77 °F (25 °C) for a maximum of 4 hours before
you feed your baby.
Note: For more information about the breast pump and tips for expressing milk, visit
www.philips.com/avent.
Instructions for storing the breast milk
-Write the date on the storage container. Include your child's name if you are giving the milk to a
child care provider.
-Gently swirl the container to mix the cream part of the breast milk that may rise to the top back into
the rest of the milk. Do not shake the milk. This can make some of the milk’s valuable parts break
down.
-Refrigerate or chill milk right after it is pumped, if possible. You can put it in the refrigerator, place it
in a cooler or insulated cooler pack, or freeze it in small (2 to 4ounce) batches for later feedings.
Pumped milk at room temperature is fine without being refrigerated for up to 4hours after
pumping.
Below you find guidelines for storing breast milk:
Storage location and temperaturesType of breast milk
Countertop 77 °F
(25 °C) or colder (room
temperature)
Refrigerator 40 °F
(4 °C)
Freezer 0 °F (-18 °C) or
colder
Freshly expressed or
pumped
Up to 4hours Up to 4 days Within 6 months is best
Up to 12 months is
acceptable
Thawed, previously
frozen
1–2hours Up to 1 day (24 hours) NEVER refreeze human
milk after it has been
thawed
Leftover from a feeding
(baby did not finish the
bottle)
Use within 2hours after the baby is finished feeding
Source: https://www.cdc.gov/breastfeeding/recommendations/handling_breastmilk.htm
Warning: Never refreeze thawed breast milk to avoid a decrease in milk quality.
Warning: Never add fresh breast milk to frozen breast milk to avoid a decrease in milk
quality and unintended thawing of the frozen milk.