Philips R3306 User manual

Register your product and get support at：
www.philips.com/support
User manual
R3306
3000 Series
Clock Radio

2
4 EN
Your clock radio
Congratulations on your purchase, and welcome
to Philips! To fully benet from the support that
Philips oers, register your product at
www.philips.com/support.
Introduction
With this clock radio, you can
•
•
listen to FM radio
What's in the box
Check and identify the contents of your package:
• Main unit
• Power adaptor
• Quick start guide
• Safey sheet
Warranty
•
Overview of the clock radio
16
7
2
3
4
5
1
6
2
3
4
7
set two alarms to ring at dierent times.
• Turn on or switch to standby.
PRESET / SET TIME
• Store radio stations in memory.
• Select a preset radio station.
• Set time.
HR / MIN / TUN
•
Tune to FM radio stations.•
Set hour and minute.
SNOOZE / BRIGHTNESS
• Snooze alarm.
• Adjust display brightness.
SLEEP / SCAN
•
Scan and store radio stations automatically.
•
Set the sleep timer.
5Display panel
• Display current status.
AL1 / AL2 / VOL
• Set alarm.
• Adjust volume.

Caution
• Risk of product damage! Make sure that the power
voltage corresponds to the voltage printed on the
back or underside of the clock radio.
• Risk of electrical shock! When you unplug the power
cord, always pull the plug from the socket. Never pull
the cord.
Note
•
3
Get started
Always follow the instructions in this chapter in
The batteries can only back up clock and alarm
settings.
Connect the power adaptor to the wall outlet.
sequence.
Install batteries
Connect power
Caution
• Risk of explosion! Keep the batteries away from heat,
sunshine or re. Never discard batteries in re.
• Batteries contain chemical substances, so they should
be disposed of properly.
• Do not mix battery types: e.g. alkaline with carbon
zinc. Only use batteries of the same type for the set.
The type plate is located at the bottom of the clock
radio.
Insert 2 AAA batteries (not provided) with
correct polarity (+/-) as illustrated.
Set time
Note
• You can only set time in standby mode.
1 In standby mode, press and hold SET TIME
for 2 seconds.
2 Press HR to set hour and MIN to set
minute, then press to conrm.
SET TIME
The time is set.
5
EN

4 Listen to FM radio
Note
• Keep the clock radio away from other electronic
devices to avoid radio interference.
• For better reception, fully extend and adjust the
position of the FM antenna.
Tune to FM radio stations
1 Press to turn on the clock radio.
2 Press and hold TUN
for 2 seconds.
The clock radio tunes to a station with
strong reception automatically.
3 Repeat Step 2 to tune to more radio stations.
To tune to a station manually:
Press TUN repeatedly to select a frequency.
Note
• The tuning grid of the clock radio is 50KHz, the radio
frequency on the display panel will increase 0.1MHz
by pressing
TUN twice.
Tip
• To remove a pre-stored station, store another station
in its place.
Select a preset radio
station
In FM tuner mode, press PRESET repeatedly to
select a preset number.
Adjust volume
While listening, press VOL
to adjust volume.
Store FM radio stations
automatically
Store FM radio stations
manually
In FM tuner mode, press and hold SCAN for
more than 2 seconds.
The unit stores all the available FM radio
stations automatically and broadcasts the
rst station.
Note
• You can store a maximum of 20 FM radio stations.
1In FM tuner mode，tune to an FM radio station.
2Press and hold PRESET for 2 seconds to
activate programming mode.
The preset number begins to blink.
3Press TUN
TUN
repeatedly to select a number.
4Press again to conrm.PRESET
5Repeat steps 1 to 4 to store more FM radio
stations.
6 EN
Option A:
1 In FM tuner mode, press PRESET.
2 Press to select a preset radio station.
Option B:

5 Other features
Set alarm time
Set alarm
Note
• You can only set the alarm in standby mode.
• Make sure that you have set the clock correctly.
1In standby mode, press and hold AL1 or
AL2 for 2 seconds to set alarm time.
2Press HR to set hour and MIN to set
to conrm.minute, then press AL1 or AL2
Tip
• The unit exits alarm setting mode when being idle for
10 seconds.
Select alarm source
You can select FM radio or buzzer as the alarm
source by pressing AL1 or AL2 in standby
mode.
The corresponding alarm icon lights up.
Activate/deactivate alarm timer
Press AL1 or AL2 repeatedly to activate or
deactivate the alarm timer.
If the alarm timer is activated, the alarm
indicator turns on.
If the alarm timer is deactivated, the alarm
indicator turns o.
The alarm repeats ringing for the next day.
To stop the alarm, press the coresponding
AL1 or AL2.
Snooze the alarm
When the alarm sounds, press SNOOZE.
The alarm snoozes and repeats ringing 9
minutes later.
Set sleep timer
This clock radio can switch to standby mode
automatically after a preset period.
• Press SLEEP repeatedly to select a period
(in minutes).
The clock radio switches to standby mode
automatically after the preset period.
To deactivate the sleep timer:
• Press SLEEP repeatedly until [OFF] (o)
appears.
Adjust display brightness
Press BRIGHTNESS repeatedly to select
dierent brightness levels:
• High
• Medium
• Low
7
EN

8EN
6 Product
information
Note
• Product information is subject to change without prior
notice.
Rated Output Power 400mW RMS
Tuner (FM)
Amplier
Tuning Range 87.5-108 MHz
Tuning Grid 50 KHz
Sensitivity
- Mono, 26 dB S/N Ratio <22 dBf
Total Harmonic Distortion <3%
Signal to Noise Ratio >50 dBA
General information
AC Power (power
adaptor)
Brand: Philips
Model: AS030-
Input: 100-240V~
50/60 Hz; 0.15A
Output: 5V 0.6A
Operation Power
Consumption <3 W
Standby Power
Consumption <1 W
Dimensions
(W x H x D) 186 x 96 x 65 mm
Weight
(Main unit) 296 g
7
Troubleshooting
Warning
• Never remove the casing of the product.
To keep the warranty valid, never try to repair
the device yourself. If you encounter problems
when using this device, check the following
points before requesting service. If the problem
remains unsolved, go to the Philips webpage
www.philips.com/support. When you contact
Philips, make sure that the device is nearby
and the model number and serial number are
available.
No power
• Make sure that the AC power plug of the unit
is connected properly.
• Make sure that there is power at the AC outlet.
No sound
• Adjust the volume.
No response from the unit
• Disconnect and reconnect the AC power plug,
then turn on the unit again.
Poor radio reception
• Keep the clock radio away from other
electronic devices to avoid radio interference.
• Fully extend and adjust the position of the
antenna.
Alarm does not work
• Set the clock/alarm correctly.
Clock/alarm setting erased
• Power has been interrupted or the power
plug has been disconnected.
• Reset the clock/alarm.
• Replace the backup batteries.
050-EE060