Philips CD 450 User manual

CD450/455
User Guide
PCE DRAFT
1.8/1.9GHZDECT TELEPHONE
DIGITAL ANSWERING MACHINE
LOW RADIATION
CALLER ID
HANDS-FREE

3
Important Safety Instructions
Important Safety Instructions
Some of the following information may not apply
to your particular product; however, when using
telephone equipment, basic safety precautions
should always be followed to reduce the risk of
fire, electric shock and injury to persons,
including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked
on the product.
3. Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth for
cleaning.
4. Telephones should not be used while you are
in a bathtub, shower or pool. Immersion of
the telephone or handset in water could
cause an electrical shock.
5. Slots and openings in the cabinet back or
bottom are provided for ventilation, to
protect it from overheating. These openings
must not be blocked or covered. The
openings should never be blocked by placing
the product on the bed, sofa, rug, or other
similar surface. This product should not be
placed in a built-in installation unless proper
ventilation is provided.
6. This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the type
of power supply to your home, consult your
dealer or local power company.
7. Do not allow anything to rest on the power
cord. Do not locate this product where the
cord will be abused by persons walking on it.
8. Do not overload wall outlets and extension
cords as this can result in the risk of fire or
electric shock.
9. Never push objects of any kind into this
product through cabinet slots as they may
touch dangerous voltage points or short out
parts that could result in a risk of fire or
electric shock. Never spill liquid of any kind
on the product.
10. To reduce the risk of electric shock, do not
disassemble this product, but take it to a
qualified service personnel when service or
repair work is required. Opening or
removing covers may expose you to
dangerous voltages or other risks. Incorrect
reassemblycancauseelectricshockwhenthe
appliance is subsequently used.
11. Do not expose the product to extreme
temperatures such as areas near a hot
radiator or stove or in a hot car.
12. Do not place lighted candles, cigarettes,
cigars, etc., on the telephone.
13. Never touch uninsulated telephone wires or
terminals unless the telephone line has been
disconnected at the network interface.
14. Never install or modify telephone wiring
during a lightning storm.
15. Never install telephone jacks in wet locations
unless the jack is specifically designed for wet
locations.
16. Use caution when installing or modifying
telephone lines to prevent electrical shock
and/or fire.
17. Unplug this product from the wall outlet and
refer servicing to qualified service personnel
under the following conditions:
A. When the power supply cord or plug is
damaged or frayed.
B. If the product has been exposed to rain or
water.
C. If the product does not operate normally
by following the operating instructions.
D. If the product’s cabinet has been damaged.
E. If the product exhibits a distinct change in
performance.
18. Avoid using a telephone (other than a
cordless type) during an electrical storm.
There may be a remote risk of electric shock
from lightning.
19. Donot use thetelephone to reporta gas leak
in the vicinity of the leak.
20. Donotplacethisproductonanunstablecart,
stand or table. The product may fall, causing
serious damage to the product.

4Important Safety Instructions
IF YOUR PRODUCT UTILIZES
BATTERIES, THE FOLLOWING
ADDITIONAL PRECAUTIONS SHOULD
BE OBSERVED:
1. Use only the type and size of battery(ies)
specified in the user manual.
2. Do not dispose of the battery(ies) in fire.
They may explode. Check with local codes
for possible special disposal instructions.
3. Do not open or mutilate the battery(ies).
Released electrolyte is corrosive and may
cause damage to the eyes or skin. It may be
toxic if swallowed.
4. Exercisecare in handlingbattery(ies) in order
not to short out the battery(ies) with
conducting materials such as rings, bracelets,
and keys. The battery(ies) or conductor may
overheat and cause burns.
5. Do not attempt to recharge the battery(ies)
provided with or identified for use with this
product that are not intended to be charged.
The battery(ies) may leak corrosive
electrolyte or explode.
6. Donotattempttorejuvenatethebattery(ies)
provided with or identified for use with this
product by heating them. Sudden release of
thebattery(ies)electrolytemayoccurcausing
burns or irritation to eyes or skin.
7. When replacing battery(ies), all batteries
should be replaced at the same time. Mixing
fresh and discharged batteries could increase
internal cell pressure and rupture the
discharged battery(ies). (Applies to products
employing more than one separately
replaceable primary battery.)
8. Wheninsertingbattery(ies)intothisproduct,
the proper polarity or direction must be
observed. Reverse insertion of battery(ies)
can cause charging, and that may result in
leakage or explosion.
9. Remove battery(ies) from this product if
storing over 30 days because the battery(ies)
could leak and damage the product.
10. Discard “dead” battery(ies) as soon as
possible since “dead“ batteries are more
likely to leak in a product.
11. Donot storethis product, orthe battery(ies)
provided with or identified for use with this
product, in high-temperature areas.
Batteries that are stored in a freezer or
refrigerator for the purpose of extending
shelf life should be protected from
condensation during storage and defrosting.
Batteries should be stabilized at room
temperature prior to use after cold storage.
12. If your product uses rechargeable
battery(ies), charge the battery(ies) only in
accordance with the instructions and
limitation specified in the User Manual.
SAVE THESE INSTRUCTIONS

- 1 -
Table of Contents
1
11
1Environment
EnvironmentEnvironment
Environment ................................
................................................................
................................................................
................................................................
................................................................
................................................................
...................................
......
...2
22
2
2
22
2Safety
SafetySafety
Safety ................................
................................................................
................................................................
................................................................
................................................................
................................................................
.............................................
..........................
.............3
33
3
3
33
3 What’s in the Box?
What’s in the Box?What’s in the Box?
What’s in the Box?................................
................................................................
................................................................
................................................................
..........................................................
....................................................
..........................5
55
5
4
44
4Welcome
WelcomeWelcome
Welcome................................
................................................................
................................................................
................................................................
................................................................
................................................................
........................................
................
........6
66
6
5
55
5Aboutyourphone
About your phoneAbout your phone
About your phone................................
................................................................
................................................................
................................................................
...........................................................
......................................................
...........................7
77
7
6
66
6 Getting Started
Getting StartedGetting Started
Getting Started ................................
................................................................
................................................................
................................................................
.............................................................
..........................................................
............................. 11
1111
11
7
77
7Call
CallCall
Call ................................
................................................................
................................................................
................................................................
................................................................
................................................................
...............................................
..............................
............... 17
1717
17
8
88
8 Intercom and Conference Calls
Intercom and Conference CallsIntercom and Conference Calls
Intercom and Conference Calls................................
................................................................
................................................................
................................................................
....................................
........
.... 22
2222
22
9
99
9TextandNumbers
Text and NumbersText and Numbers
Text and Numbers................................
................................................................
................................................................
................................................................
........................................................
................................................
........................ 24
2424
24
10
1010
10 Phonebook
PhonebookPhonebook
Phonebook................................
................................................................
................................................................
................................................................
................................................................
................................................................
...................................
......
... 25
2525
25
11
1111
11 Call Lo
Call LoCall Lo
Call Log and Redial List
g and Redial Listg and Redial List
g and Redial List................................
................................................................
................................................................
................................................................
................................................
................................
................ 29
2929
29
12
1212
12 Custom Options
Custom OptionsCustom Options
Custom Options................................
................................................................
................................................................
................................................................
...........................................................
......................................................
........................... 31
3131
31
13
1313
13 Calling Features
Calling FeaturesCalling Features
Calling Features ................................
................................................................
................................................................
................................................................
...........................................................
......................................................
........................... 33
3333
33
14
1414
14 Network Services
Network ServicesNetwork Services
Network Services................................
................................................................
................................................................
................................................................
..........................................................
....................................................
.......................... 38
3838
38
15
1515
15 Extra Features
Extra FeaturesExtra Features
Extra Features ................................
................................................................
................................................................
................................................................
..............................................................
............................................................
.............................. 42
4242
42
16
1616
16 The System
The SystemThe System
The System ................................
................................................................
................................................................
................................................................
................................................................
................................................................
..................................
....
.. 45
4545
45
17
1717
17 The Answering Machine
The Answering MachineThe Answering Machine
The Answering Machine................................
................................................................
................................................................
................................................................
...............................................
..............................
............... 48
4848
48
18
1818
18 Appendix
AppendixAppendix
Appendix................................
................................................................
................................................................
................................................................
................................................................
................................................................
......................................
............
...... 56
5656
56
- 2 -
Environment
Environmental
Remember to observe local regulations regarding the disposal of your packaging
materials, exhausted batteries and old equipment. Promote their recycling where
possible.
Recycling & disposal
Disposal instructions for old products: The purpose of the WEEE directive (Waste
Electrical and Electronic Equipment; 2002/96/EC) is to ensure that products are
recycled using the best available treatment, recovery and recycling techniques to
ensure human health and high environmental protection. Your product is
designed and manufactured with high quality materials and components which
can be recycled and reused.
•Do not dispose of your old product in your general household
waste bin.
•Inform yourself about the local separate collection system for
electrical and electronic products marked by this symbol.
Use one of the following disposal options:
•Dispose of the complete product (including its cables, plugs and accessories)
in the designated WEEE collection facilities.
•If you purchase a replacement product, hand your complete old product back
to the retailer. He should accept it as required by the WEEE directive.
Disposal instructions for batteries:
Batteries should not be disposed of with general household waste.

- 3 -
Safety
IMPORTANT
This product is not designed for making emergency telephone calls when the
power fails. Alternative arrangements should be made for access to emergency
services.
Power requirements
This product requires an electrical supply of 100-240 volts, single-phase
alternating current, excluding IT installations defined in standard EN 60950.
Handset Charger Adapter
Input: 100-240VAC 50/60Hz
Output: 7.5VDC 200mA
Base Unit Adapter
Input: 100-240VAC 50/60Hz
Output: 7.5VDC 500mA
Battery requirements
The handset requires a power source of two rechargeable NiMH batteries, size
AAA 1.2V 750mAh (HR10/44).
CAUTION: Use only the mains adapter supplied with this equipment. Incorrect
adapter polarity or voltage can seriously damage the unit.
CAUTION: The electrical network is classified as dangerous according to criteria
in the standard EN 60950. The only way to power down this product is by
unplugging the power supply from the electrical outlet. Ensure the electrical
outlet is located close to the apparatus and is always easily accessible.
WARNING: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRE
C
T TYPE.
Never use non-rechargeable batteries. Use the recommended type supplied
with this product. NiMH batteries must be disposed of in accordance with the
applicable waste disposal regulations.
Safety
- 4 -
Telephone connections
The voltage on the network is classified as TNV-3 (Telecommunication Network
Voltages, as defined in the standard EN 60950). Following a power cut, the call in
progress as well as the date and time settings is lost.
Hearing aid
Please note that this telephone works by sending radio signals between the base
unit and the handset. These signals may interfere with some hearing aids,
causing a humming noise.
Safety precautions
•Do not allow the handset to come into contact with liquids or moisture.
•Do not open the handset, base unit or charger. This could expose you to high
voltages.
•Do not allow the charging contacts or the battery to come into contact with
conductive materials.
•There is a slight chance that your product could be damaged by an electrical
storm. We recommend that you unplug the product from the power supply and
telephone socket during a storm.
•Do not use the handset in an explosive hazard area such as where there is
gas leaking.
•It is recommended that this product is not used near intensive care medical
equipment or by persons with pacemakers.
•This product can interfere with electrical equipment such as answering
machines, television, radio, and computers if placed too close. We
recommend that you position the base unit at least one meter from such
appliances.
The marking certifies compliance with technical regulations in accordance
with Directive 1999/5/EC for the safety of the user, electromagnetic perturbations
and for radio spectrum.

- 5 -
What’s in the Box?
Congratulations on your purchase and welcome to Philips! To fully benefit from
the support that Philips offers, register your product at www.philips.com/welcome.
This product comes with the following items. For missing item(s), contact your
dealer.
Base Unit with bracket Handset x1 Handset Battery Cover x1
Base Power Adapter NiMH AAA
Rechargeable Battery x2
Telephone Line Cord x1
This User Guide Quick Start Guide Warranty Leaflet
Charger Charger Power Adapter Jack Adapter
- 6 -
Welcome
This user guide provides you with the information and instructions you need to get
the most from your phone.
HOW TO USE THIS USER GUIDE?
The following symbols are used to alert you to important information.
Warning:
::
: Critical information for preventing personal injury.
Caution:
Caution:Caution:
Caution:
Critical information for preventing damage to the
product.
Tip:
Tip:Tip:
Tip: Information for easier operation.
Note:
Note:Note:
Note: Explanatory or critical information for carrying out an
operation correctly.
NEED MORE HELP?
•See the Frequently asked questions section in this user guide on page 58.
•Visit our online help www.philips.com/support

- 7 -
About your phone
THE HANDSET
1
11
1
Up Navigation & Call Log key Up Navigation & Call Log keyUp Navigation & Call Log key
Up Navigation & Call Log key
Scroll up menu
Increase earpiece volume
Enter call log
2
22
2
Left soft key Left soft keyLeft soft key
Left soft key
Confirm selection
Enter options menu
3
33
3
Right s Right sRight s
Right soft key 2
oft key 2oft key 2
oft key 2
Delete text or digit(s)
Cancel operation
View more record information
4
44
4
Talk & Recall key Talk & Recall keyTalk & Recall key
Talk & Recall key
Make and receive calls
Send flash signal
5
55
5
End & On / Off key End & On / Off keyEnd & On / Off key
End & On / Off key
End call
Exit menu / operation
Turn handset on/off
6
66
6 Menu key
Menu keyMenu key
Menu key
Access main menu
7
77
7 Down Navigation & Phonebook key
Down Navigation & Phonebook keyDown Navigation & Phonebook key
Down Navigation & Phonebook key
Scroll down menu
Decrease earpiece volume
Enter phonebook
8
88
8
Speaker key Speaker keySpeaker key
Speaker key
Turn speaker on / off
9
99
9
Redial key Redial keyRedial key
Redial key
Enter redial list & dial last number
12
1212
12
Ringer Off & Pause key Ringer Off & Pause keyRinger Off & Pause key
Ringer Off & Pause key
Dial # and enter pause
Turn ringer on / off
Change input letter case
10
1010
10 Digit keys
Digit keysDigit keys
Digit keys
Dial digit and enter text
Use as shortcut key for quick dial
13
1313
13
Mute key Mute keyMute key
Mute key
Mute / unmute microphone
11
1111
11
Star StarStar
Star & Keylock key
& Keylock key& Keylock key
& Keylock key
Dial * & send temp DTMF signal
Lock / unlock keypad
14
1414
14
Intercom IntercomIntercom
Intercom & Conference key
& Conference key& Conference key
& Conference key
Make intercom call
Make conference call
About Your Phone
- 8 -
THE BASE AND ANSWERING MACHINE
1
11
1
Answering Machine On Answering Machine OnAnswering Machine On
Answering Machine On
/ //
/
Off key Off keyOff key
Off key
Turn the answering machine on / off
5
55
5
Rewind key Rewind keyRewind key
Rewind key
Skip backward during playback
2
22
2
Volume down Volume downVolume down
Volume down
Decrease speaker volume
6
66
6
Play & Play &Play &
Play & Stop
StopStop
Stop key
keykey
key
Play messages
Stop message playback
3
33
3
Delete key Delete keyDelete key
Delete key
Delete messages
7
77
7
Forward key Forward keyForward key
Forward key
Skip forward during playback
4
44
4
Volume up Volume upVolume up
Volume up
Increase speaker volume
8
88
8
Page key Page keyPage key
Page key
Find handset(s)
Enter registration mode
9 99
9
7 77
7-
--
-segment display
segment displaysegment display
segment display
Display message number
Display answering machine operation

About Your Phone
- 9 -
THE ICONS
Each icon gives you a visual message of what is happening on your handset.
Battery level Signal strength
Call in progress Alarm on
Speaker on Ringer off
Call log Phonebook
Answering machine Voicemail indicator
More options upward More options downward
THE MENUS
Your phone offers a variety of features and functions grouped in the menus.
Browsing the menus
The main menu includes the Phonebook, Clock & Alarm, Personal Set, Advanced
Set, Network Service and Answering Machine menus.
From standby mode, you can,
•Press to enter the main menu.
•Press
to enter the incoming call log.
•Press to enter the phonebook.
•Press
to enter the redial list.
TIP: Use or to navigate the menus.
TIP: Quick Exit.
Quick Exit.Quick Exit.
Quick Exit. Press and hold to exit from any menu instantly.
All unconfirmed changes will not be saved.
About Your Phone
- 10 -
Taking a glance at the menus
Main menu
Main menuMain menu
Main menu
Othe OtheOthe
Other menus
r menusr menus
r menus
Phonebook
PhonebookPhonebook
Phonebook
Advanced set Advanced setAdvanced set
Advanced set
Answer machine Answer machineAnswer machine
Answer machine
Call log Call logCall log
Call log
New entry
List entry
Edit entry
Select melody
Delete entry
Delete all
Direct memory
Play
Delete all
Answer on/off
Record OGM
Answer mode*
Ans settings
Call list
Copy to phbk
Delete
Delete all
TAM*
Redial list
Redial listRedial list
Redial list
Clock & alarm
Clock & alarmClock & alarm
Clock & alarm
Set date & time
Set format*
Alarm
Alarm tone
Easy call*
Conference*
Call barring*
Russian CID*
XHD sound*
Change PIN
Registration
Unregister
Country*
Reset
Area code*
Carrier code*
Auto prefix*
Recall time
Dial mode*
First ring*
Redial list
Copy to phbk
Delete
Delete all
Personal set
Personal setPersonal set
Personal set
Net services* Net services*Net services*
Net services*
Handset name
Handset tones
Language*
Contrast*
Auto hang up*
Backlight*
Call forward
Callfwd busy
Callfwd unans
Voicemail 1
Voicemail 2
Info 1
Info 2
Call return
Cancel call back
Withhold ID
* This menu item is
* This menu item is* This menu item is
* This menu item is country
countrycountry
country-
--
-dependent.
dependent.dependent.
dependent.

- 11 -
Getting Started
CONNECTING YOUR PHONE
1. Connect the output plug of the mains
adapter to the bottom of the base unit.
2. Connect the mains adapter to a
standard wall outlet.
3. Connect the telephone line cord to the
phone socket at the bottom of the
base unit and the wall phone socket.
CONNECTING YOUR CHARGER
* For multi
* For multi* For multi
* For multi-
--
-pack
packpack
pack models
modelsmodels
models only
onlyonly
only
1. Connect the output plug of the mains
adapter to the bottom of the charger.
2. Connect the mains adapter to a
standard wall outlet.
Getting Started
- 12 -
WALL MOUNTING THE BASE
The charger is designed to support wall mounting. If you prefer to wall mount the
charger, follow the instructions below.
1. Remove the bracket from the back of
the base unit by pressing down the
two latches on the top of the bracket.
2. Turn the bracket upside down and
then re-insert the bracket to the back
of the base unit.
[Image to be added]
[Image to be added][Image to be added]
[Image to be added]
3. Insert screws (not included) into the
wall.
The recommended mounting screws
are Philips Pan Head Self-Tapping
Screws with diameter 4mm and length
20mm.
[Image to be added]
[Image to be added][Image to be added]
[Image to be added]
4. Align the mounting holes on the back
of the base with the screws on the
wall.
5. Slide the base down into place.
CAUTION: Other wall mounting methods are not recommended and may
damage the product.

Getting Started
- 13 -
CHARGING YOUR HANDSET
1. Place the 2 rechargeable batteries
(included) into the battery
compartment.
2. Slide the battery door firmly into place.
3. Place the handset on the base unit or
charger for charging.
WARNING: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
Never use non-rechargeable batteries. Use recommended type supplied with
this product. NiMH batteries must be disposed of in accordance with the
applicable waste disposal regulations.
NOTE: Charge the handset(s) for 24 hours before initial use!
NOTE: Handset may get warm during initial charging. This is normal.
The handset may take a few seconds to power up.
CAUTION: Check the battery polarity when inserting in the battery compartment.
Incorrect polarity may damage the product.
Getting Started
- 14 -
CHECKING THE BATTERY LEVEL
The battery icon displays the current battery level.
= Battery full = Battery empty. Require charging.
Your handset may power down shortly if it is not charged after the battery is
empty. If you are on the phone when the battery is nearly empty, you will hear
warning tones. Your call may be cut off shortly after the warning.
GREETING YOU WITH “WELCOME”
This feature only applies to model(s) with multiple
This feature only applies to model(s) with multipleThis feature only applies to model(s) with multiple
This feature only applies to model(s) with multiple-
--
-country or language support.
country or language support.country or language support.
country or language support.
At first startup, your handset greets you with a “Welcome” message. After the
welcome message, you can set the country or language to start using the phone.
Setting your country/language
It is necessary to set the correct country for the phone for it to work properly
according to your country’s standards.
After the welcome message,
1. Select your country or language.
2. Press OK to confirm. The country/language setting is saved.
After setting the country/language, you can set the date and time. Your phone is
now ready to use.
To re-configure your country or language setting, see Changing the country
setting on page 46 or Setting the display language on page 31.
NOTE: Date/Time.
Date/Time.Date/Time.
Date/Time. Press BACK to skip date/time setting.
NOTE: Press OK to skip the welcome message.

Getting Started
- 15 -
SETTING THE CLOCK
Your phone has a digital clock. Set the clock before initial use of the phone.
Setting the date and time
1. Press .
2. Select C
CC
Clock &
lock &lock &
lock & alarm
alarmalarm
alarm 


S SS
Set date
et dateet date
et date &
&&
& time
timetime
time. Press OK .
3. Use the digit keys to enter the date.
4. Press OK . The handset displays the time editing screen.
5. Use digit keys to enter the time.
6. Press OK . The setting is saved.
Setting the date and time format
This feature only applies to model(s) with date/time format support.
This feature only applies to model(s) with date/time format support.This feature only applies to model(s) with date/time format support.
This feature only applies to model(s) with date/time format support.
You can choose how your phone displays the date (DD/MM or MM/DD) and time
(12-hour or 24-hour).
1. Press .
2. Select C
CC
Clock &
lock &lock &
lock & alarm
alarmalarm
alarm 


S SS
Set
etet
et format
formatformat
format. Press OK .
3. Select D
DD
Date format
ate formatate format
ate format
or T TT
Time format
ime formatime format
ime format.
..
.
4. Select the setting you want.
5. Press OK . The setting is saved.
WHAT IS STANDBY MODE?
Your phone is in standby mode when it is idle. The standby screen displays the
handset name, the handset number, the date and time, the signal icon, and the
battery icon.
Getting Started
- 16 -
CHECKING THE SIGNAL STRENGTH
The signal icon displays the link status between your handset and the base
unit. A steady icon means your handset and the base unit are linked. A flashing
icon means your handset and the base unit are not linked.
If you move too far away from the base unit while you are on the phone, you will
hear warning tones notifying you that your handset is almost out of range – lost
link. Take your handset closer to the base unit or your call may be cut off shortly
after the warning.
SWITCHING YOUR HANDSET ON/OFF
Switching on your handset
1. Press . The handset may take a few seconds to power up.
Switching off your handset
1. Press and hold . The handset’s screen turns off.
NOTE: If your handset has lost link, you will not be able to make or
receive any calls. You will also not be able to carry out many of the
phone’s functions and features.
NOTE:
Y
our handset cannot receive any calls if the power is switched off.

- 17 -
Call
MAKING A CALL
This section describes the different ways to make a call.
1. Press .
2. Dial the phone number. The number displays on the screen and is
dialed out.
Pre-dialing
Pre-dialing lets you view and edit the number before making the call.
1. Enter the phone number. The number displays on the screen. You
can make changes before dialing out.
2. Press to dial out the call.
NOTE: Low Battery.
Low Batter
y
.Low Batter
y
.
Low Battery. During a call, you will hear warning tones if your
handset is almost out of battery. Charge your handset or your call may
soon be cut off. For details, see Checking the battery level on page 14.
TIP: Press BACK to erase a digit.
Press and hold to enter a pause. P displays on the screen.
NOTE: Signal Strengt
h
Si
g
nal Stren
g
thSi
g
nal Stren
g
t
h
Signal Strength. Check the signal strength before making a call and
during a call. For details, see Checking the signal strength on page 16.
NOTE: Emergency Call.
Emer
g
enc
y
Call.Emer
g
enc
y
Call.
Emergency Call. This telephone is not designed for making
emergency telephone calls when the power fails. Alternative
arrangements should be made for access to emergency services.
NOTE: Call Timer.
Call Timer.Call Timer.
Call Timer. The call timer displays the talk time of your current call.
Call
- 18 -
Redialing the last number
1. Press .
2. Press . The last number displays on screen and is dialed out.
Calling from the redial list
1. Press .
2. Select the record you want to call.
3. Press . The number is dialed out.
Calling from the phonebook
For details on the phonebook, see Phonebook on page 25.
1. Press to access the phonebook.
2. Select the phonebook record you want to call.
3. Press to dial out the call.
Calling from the call log
You can return a call from the incoming (received or missed) call log. For details, see
Call Log on page 29.
1. Enter the call log.
2. Select the record you want to call.
3. Press to dial out the call.
ENDING A CALL
1. Press .
TIP: Auto hang u
p
A
uto han
g
u
p
Auto han
g
u
p
A
uto hang up. Place the handset on the base or charging cradle to
end the call automatically. See Auto hang up on page 33.

Call
- 19 -
ANSWERING A CALL
If you have a Russia model phone, refer to the
If you have a Russia model phone, refer to theIf you have a Russia model phone, refer to the
If you have a Russia model phone, refer to the Answering
AnsweringAnswering
Answering
a aa
a
call callcall
call
(For (For(For
(For
Russia RussiaRussia
Russia-
--
-model)
model)model)
model) section.
section.section.
section.
When you receive a call, your phone rings. Press or to answer the call.
Turning off the ringer
You can turn off the ringer for all incoming calls.
1. Press and hold during standby. displays on the screen. For
details on the ringer setting, see Personalizing your phone’s sounds
on page 32.
ANSWERING A CALL (FOR RUSSIA-MODEL)
If you have a Russia-model phone, the tips and notes mentioned in the Answering
a call section still applies to you. However, in your country, there are 2 ways to
answer a call depending on your Caller ID setting.
NOTE: Ringe
r
Rin
g
erRin
g
e
r
Ringer. When the handset rings during an incoming call, do not
put the handset too close to your ear as the ringer volume may
damage your hearing.
TIP: Silent Ringer
Silent RingerSilent Ringer
Silent Ringer. When the phone is ringing, press to turn off
the ringer for the current call.
NOTE: Handsfree
HandsfreeHandsfree
Handsfree. Handsfree activation can suddenly increase the
earpiece volume to a very high level. Make sure the handset is not too
close to your ear.
NOTE: Caller ID Service.
Caller ID Service.Caller ID Service.
Caller ID Service. Subscribe from your service provider.
TIP: Missed Call Aler
t
Missed Call AlertMissed Call Aler
t
Missed Call Alert. When a call is missed,
y
our handset displays a
notification message. The handset’s LED and icon also flash.
Call
- 20 -
Caller ID service enabled,
1. Press OK to view the Caller ID when your phone is ringing.
2. Press or to answer the call.
Caller ID service disabled,
1. Press or to answer the call when your phone is ringing.
Russian CID setting
This feature changes the caller ID setting.
1. Press .
2. Select A
AA
Advanced
dvanceddvanced
dvanced set
setset
set 

Russian CID
Russian CIDRussian CID
Russian CID. Press OK .
3. Select the new setting. Press OK . The setting is saved.
DURING A CALL
This section describes the features that are available during a call.
Adjusting the earpiece volume
1. Press or to adjust the volume during a call. Press OK to
confirm.
Muting the microphone
The mute feature allows you to speak to someone in the house privately.
1. Press during a call. Your handset displays Mute on
Mute onMute on
Mute on. The caller
cannot hear you, but you can still hear his voice.
Press again to un-mute the microphone. You can now
communicate with the caller.
USING THE SPEAKER OR HANDSFREE
1. Press to turn on/off the speaker.

Call
- 21 -
MAKING A SECOND CALL
During a call,
1. Press OR
OROR
OR
Press OK. Select Init
InitInit
Init 2nd
2nd2nd
2nd
call callcall
call. Press OK again.
Your first call will be put on hold.
2. Dial the number you want. The number displays on the screen and
is dialed out.
Answering a second call
During a call, your phone sounds a short beep periodically to notify you of an
incoming call.
1. Press to answer the call. The first call is put on hold, and you
are now connected to the second call.
Toggling between two external calls
1. Press OR
OROR
OR
Press OK and select Switch call
Switch callSwitch call
Switch call. Press OK .
The current call is put on hold, and you are now connected to the other call.
NOTE: 2nd Call Service
2nd Call Service2nd Call Service
2nd Call Service. Subscribe from your service provider.
NOTE: 2nd Call Service
2nd Call Service2nd Call Service
2nd Call Service. Subscribe from your service provider.
TIP: Conference
ConferenceConference
Conference. The conference feature may require additional
charges from your service provider.
To start a conference call, while connected to two external calls, you
can press OK , select Conference
ConferenceConference
Conference, and then press OK again. You can
now talk to both parties at once.
- 22 -
Intercom and Conference Calls
An intercom call is a call to another handset that shares the same base unit. A
conference call involves a conversation between another handset and outside
caller(s).
CALLING ANOTHER HANDSET
1. Press .
2. Select or press the target handset number. Press OK .
3. Wait for the other party to answer your call.
4. Press to cancel or end the intercom call.
While you are on the phone
While talking on the phone, you can call another handset.
1. Press during the call. The external caller is automatically being
put on hold.
2. Select or press the target handset number. Press OK .
3. Wait for the other party to answer your call.
To toggle between the calls
1. Press to switch between the outside call and the intercom call.
TRANSFERRING A CALL
1. Press during a call.
2. Select or press the target handset number. Press OK .
3. Press after the other party answers your call. The outside call
is now transferred to the other handset.
NOTE: If the base unit only has 2 handsets (yours and another handset)
registered to it, you can press to call the other handset instantly.

Call
- 23 -
MAKING A CONFERENCE CALL
A 3-way conference call is a call between you, outside caller(s), and another handset
user in your house.
You are talking on the phone with an outside caller and you want to involve
another handset user in the conversation.
During your call with the outside caller,
1. Press . The external caller is automatically being placed on
hold.
2. Select or press the target handset number. Wait for the other party
to answer your call.
3. Press and hold . You are now on a 3-way conference call.
4. Press to end the conference call.
TIP: Auto Conference
A
uto ConferenceAuto Conference
A
uto Conference.
Y
ou can join an ongoing external call with
another handset by pressing . See Activating/Deactivating auto
conference on page 33.
NOTE:
A
3-
w
ay conference call requires 2 handsets that share the same
base unit.
- 24 -
Text and Numbers
You can enter text and numbers for handset name, phonebook records, and
others menu items.
ENTERING TEXT AND NUMBERS
1. Find the key with the character you want.
2. Press it as many times as needed for the character you want.
I
II
Input
nputnput
nput table
tabletable
table
Key
KeyKey
Key
Characters (Upper case) Characters (Upper case)Characters (Upper case)
Characters (Upper case)
Key KeyKey
Key
Characters (Lower case) Characters (Lower case)Characters (Lower case)
Characters (Lower case)
0 . 0 , / : ; “ ; ! ¡ ? ¿
* + - % \ ^ ~ | 0 . 0 , / : ; “ ; ! ¡ ? ¿ * + - % \ ^ ~ |
1 [Sp] 1 @ _ # = < > ( )
& ¤ £ $ ¥ [ ] { } ° § … 1 [Sp] 1 @ _ # = < > ( ) & ¤ £ $ ¥ [ ] { } ° § …
2 A B C 2 À Â Æ Á Ã ĂÄ Å ĄÇ ĆČ 2 a b c 2 à â Æ á ã ăä å ąç ćč
3 D E F 3 ĎĐĖĚÈ É Ê Ë Ę∆Φ 3 d e f 3 ďđėěè é ê ë ę∆Φ
4 G H I 4 ĞÍ Ì Î Ï İΓ 4 g h i 4 ğí ì î ï I Γ
5 J K L 5 ΛŁ ĹĽ 5 j k l 5 Λł ĺľ
6 M N O 6 Ñ ŇŃÓ Ô Õ Ö 6 m n o 6 ñ ňńó ô õ ö ő
7 P Q R S 7 ŘŞŠ ŚβΠΘΣ 7 p q r s 7 řşš śβΠΘΣ
8 T U V 8 ŢŤÙ Ú Û Ü ŮǙŰ 8 t u v 8 ţťù ú û ü ůǚűµ
9 W X Y Z 9 Ý Ž ŹŻſØ ΩΞΨ 9 w x y z 9 ý ž źżƒ ø ΩΞΨ
TIP: Change Case
Change CaseChange Case
Change Case. Press during editing, and the next letter you
enter will be in the alternate case.
TIP: Editing
EditingEditing
Editing. Use BACK to delete and or to move the cursor.

- 25 -
Phonebook
Your phone has a phonebook that can store up to 100 records. You can access
the phonebook from your handset. Each record can have a name up to 14
characters long and a number up to 24 digits long.
VIEWING THE PHONEBOOK
1. Press .
2. Select the contact you want to view.
3. Press to view the details of a record (name, number, VIP melody).
Searching a record
You can search the phonebook by scrolling or by searching the first character.
Searching by scrolling
1. While in the phonebook, press or to scroll.
Searching by the first character
1. While in the phonebook, press the digit key that contains the
character you want to search by.
During a call
You can access the phonebook and use the number during a call.
1. Press and hold during a call OR
OROR
OR
Press OK . Select Phonebook
PhonebookPhonebook
Phonebook. Press OK .
2. Select the contact you want.
3. Press OK . The number displays on the screen and is sent out.
TIP: Use or to navigate the menus.
TIP: Options
O
p
tionsO
p
tions
Options M
MM
Menu.
enu.enu.
enu. While viewing the phonebook, you can press
OK to
access the phonebook options menu.
Phonebook
- 26 -
CALLING FROM THE PHONEBOOK
See Calling from the phonebook on page 18.
ADDING A RECORD
1. Press .
2. Select Phonebook
PhonebookPhonebook
Phonebook 


New entry New entryNew entry
New entry. Press OK .
3. Enter the name. Press OK .
4. Enter the number.
5. Press OK to confirm. Your new record is saved.
EDITING A RECORD
1. Press .
2. Select Phonebook
PhonebookPhonebook
Phonebook 

E
EE
Edit entry
dit entrydit entry
dit entry. Press OK .
3. Select the contact you want to edit. Press OK .
4. Edit the name if necessary. Press OK .
5. Edit the number if necessary. Press OK to confirm. The record is
saved.
TIP: Editing
EditingEditing
Editing. Use BACK to delete and or to move the cursor.
NOTE: Memory Full
Memor
y
FullMemor
y
Full
Memory Full. If your phonebook is full, the handset displays a
notification message. Delete some records before adding new ones.
NOTE: Text and Number Editing
Text and Number Editin
g
Text and Number Editin
g
Text and Number Editing. See Text and Numbers on page 24.
NOTE: Duplicate
Du
p
licateDu
p
licate
Duplicate Record
RecordRecord
Record. Contacts with identical number cannot be
saved.
TIP: Pause
PausePause
Pause. Press and hold to insert a pause.

Phonebook
- 27 -
SETTING VIP MELODIES
You can assign different ringer melodies for each phonebook contacts. Your
phone will ring the selected melody when the caller ID matches the number in
your phonebook.
1. Press .
2. Select Phonebook
PhonebookPhonebook
Phonebook Select melody
Select melodySelect melody
Select melody. Press OK .
3. Select the contact you want. Press OK . The current melody is
displayed.
4. Select a ring melody using and . Press OK . The setting is
saved.
DELETING A RECORD
1. Press .
...
2. Select Phonebook
PhonebookPhonebook
Phonebook 


Delete DeleteDelete
Delete. Press OK .
3. Select the contact you want to delete. Press OK . The handset
displays a confirmation request.
4. Press OK to confirm. The record is deleted.
DELETING ALL RECORDS
1. Press .
2. Select Phonebook
PhonebookPhonebook
Phonebook 


D DD
Delete
eleteelete
elete a
aa
all
llll
ll. Press OK . The handset displays a
confirmation request.
3. Press OK to confirm. All records are deleted.
USING QUICK DIAL
Phonebook records can be programmed to a quick dial key (digit keys 1- 9).
NOTE: If network service shortcuts are enabled, keys 1 and 2 cannot be
used as quick dial shortcut keys. See Network Services on page 38.
Phonebook
- 28 -
Assigning a quick dial key
1. Press .
2. Select Phonebook
PhonebookPhonebook
Phonebook 


Direct memor Direct memorDirect memor
Direct memory
yy
y. Press OK .
3. Select an available key from the list. Press OK .
4. Select the contact you want. Press OK . The setting is saved.
Making a call
1. Press and hold an assigned quick dial key during standby. The
programmed number is dialed out.
Editing a quick dial key
1. Press .
2. Select Phonebook
PhonebookPhonebook
Phonebook 

Direct memory
Direct memoryDirect memory
Direct memory. Press OK .
3. Select the quick dial key you want to change. Press OK .
4. Select C
CC
Change
hangehange
hange. Press OK .
5. Select a new contact. Press OK . The setting is saved
Cancelling a quick dial key
1. Press .
2. Select Phonebook
PhonebookPhonebook
Phonebook 


D DD
Direct memo
irect memoirect memo
irect memory
ryry
ry. Press OK .
3. Select the quick dial key you want to cancel. Press OK .
4. Select D
DD
Delete
eleteelete
elete to cancel the quick dial key. Press OK . The handset
displays a confirmation request.
5. Press OK to confirm. The quick dial key is cancelled.

- 29 -
Call Log and Redial List
The call log stores the call history of all incoming (missed or received), and the
redial list stores call history of dialed calls.
Calls
CallsCalls
Calls
What is this? What is this?What is this?
What is this?
Stored records Stored recordsStored records
Stored records
Incoming Calls that you received. 50
Dialed Calls that you have made. 10
The incoming call history includes the caller name, number, call time and date.
The dialed call history includes the name and number called.
VIEWING THE CALL RECORDS
1. Press . (For CID model)
Press . Select Call List
Call ListCall List
Call List, and then press OK to enter the
incoming call log. (For ANSWERING MACHINE model) OR
OROR
OR
Press to enter the dialed call log.
2. Select the record you want to view. Press for more information.
MAKING A CALL
Returning a call
To call from the incoming call log, see Calling from the call log on page 18.
Redialing a call
To call from the redial list, see Calling from the redial list on page 18.
TIP: Use or to navigate the menus.
Call Log and Redial List
- 30 -
SAVING A CALL RECORD TO YOUR PHONEBOOK
1. Enter the call log or redial list.
2. Select the record you want while browsing the log. Press OK .
3. Select C
CC
Copy to phbk
opy to phbkopy to phbk
opy to phbk. Press OK .
4. Enter and edit the name if necessary. Press OK .
5. Enter and edit the number if necessary. Press OK . The record is
saved.
DELETING A CALL RECORD
1. Enter the call log or redial list.
2. Select the record you want while browsing the log. Press OK .
3. Select Delete
DeleteDelete
Delete. Press OK . The handset displays a confirmation
request.
4. Press OK to confirm. The record is deleted.
DELETING ALL CALL RECORDS
1. Enter the call log or redial list.
2. Press OK to enter the options menu while browsing the log.
3. Select Delete
DeleteDelete
Delete a
aa
all
llll
ll. Press OK . The handset displays a confirmation
request.
4. Press OK to confirm. All records are deleted.

- 31 -
Custom Options
Make this your phone – change the look and sound of the handset to suit your
needs and tastes.
PERSONALIZING YOUR PHONE’S DISPLAY
Naming your handset
Each handset can have its own name. It is displayed on the screen in standby.
1. Press .
2. Select P
PP
Personal set
ersonal setersonal set
ersonal set
 
H
HH
Handset
andsetandset
andset
n nn
name
ameame
ame. Press OK .
3. Enter or edit the name. Use BACK to make corrections.
4. Press OK to confirm. The setting is saved.
Setting the display language
This
ThisThis
This feature
featurefeature
feature only
onlyonly
only applies to model(s) with multiple
applies to model(s) with multipleapplies to model(s) with multiple
applies to model(s) with multiple-
--
-language support.
language support.language support.
language support.
1. Press .
2. Select P
PP
Personal set
ersonal setersonal set
ersonal set
 
Language
LanguageLanguage
Language. Press OK .
3. Select the new setting. Press OK . The setting is saved.
Setting the screen contrast level
1. Press .
2. Select P
PP
Personal set
ersonal setersonal set
ersonal set 


C CC
Contrast
ontrastontrast
ontrast. Press OK .
3. Select the new setting. Press OK . The setting is saved.
Custom Options
- 32 -
PERSONALIZING YOUR PHONE’S SOUNDS
Setting your handset’s ringer melody
You can choose from 12 different ringer melodies.
1. Press .
2. Select P
PP
Personal set
ersonal setersonal set
ersonal set
 
Handset
HandsetHandset
Handset tones
tonestones
tones
 

R RR
Ring
inging
ing melody
melodymelody
melody. Press OK .
3. Select the new setting. Press OK . The setting is saved.
Setting your handset’s ringer volume
There are 6 ringer volume levels (including ringer off) and a progressive setting.
1. Press .
2. Select P
PP
Personal set
ersonal setersonal set
ersonal set
 
Handset tones
Handset tonesHandset tones
Handset tones 


R RR
Ring
inging
ing v
vv
volume
olumeolume
olume. Press OK .
3. Select the new setting. Press OK . The setting is saved.
Setting the key tone
Key tone is the sound you hear when you press a key on your handset.
1. Press .
2. Select P
PP
Personal set
ersonal setersonal set
ersonal set
 
Handset tones
Handset tonesHandset tones
Handset tones 

Key
KeyKey
Key beep
beepbeep
beep. Press OK .
3. Select the new setting. Press OK . The setting is saved.
Enhancing the audio quality
Your phone has an equalizer just like your home stereo system. The equalizer
improves the earpiece’s sound quality.
1. Press .
2. Select A
AA
Advanced set
dvanced setdvanced set
dvanced set 


XHD sound XHD soundXHD sound
XHD sound.
..
. Press OK .
3. Select the new setting. Press OK . The setting is saved.
During a call
1. Press OK to enter the options menu. The handset displays the XHD
setting you can change to.
2. Press OK to change the setting. The setting is saved.

- 33 -
Calling Features
Your phone supports a number of call-related features to help you handle and
manage your calls.
AUTO HANG UP
Auto hang up allows you to end a call by placing the handset on the base or
charging cradle without pressing any key.
Activating/Deactivating auto hang up
1. Press .
2. Select P
PP
Personal set
ersonal setersonal set
ersonal set 

Auto hang up
Auto hang upAuto hang up
Auto hang up. Press OK .
3. Select the new setting. Press OK . The setting is saved.
AUTO CONFERENCE
Auto conference lets you join an external call with another handset by simply
pressing .
Activating/Deactivating auto conference
1. Press .
2. Select A
AA
Advanced set
dvanced setdvanced set
dvanced set 


C CC
Conference.
onference.onference.
onference. Press OK .
3. Select the new setting. Press OK . The setting is saved.
DIAL MODE
Dial mode is the telephone signal used in your country. Your phone supports tone
(DTMF) and pulse (rotary) dialing. Your phone shall already be set up for use in
your country. For details, consult your service provider.
Setting the dial mode
1. Press .
2. Select A
AA
Advanced set
dvanced setdvanced set
dvanced set
 
Dial
DialDial
Dial m
mm
mode
odeode
ode. Press OK .
3. Select the new setting. Press OK . The setting is saved.
Calling Features
- 34 -
RECALL SELECTION
Recall is a signal that needs to be sent to the network when making or answering
a second call. Your phone shall already be set up for use in your country. For
details, consult your service provider.
Setting the recall duration
1. Press .
2. Select A
AA
Advanced
dvanceddvanced
dvanced set
setset
set
 
Recall
RecallRecall
Recall time
timetime
time. Press OK .
3. Select the new setting. Press OK . The setting is saved.
CALL BARRING
Call barring allows you to block selected numbers from dialing out.
Activating/deactivating call barring
1. Press .
2. Select A
AA
Advanced
dvanceddvanced
dvanced set
setset
set 

Call barri
Call barriCall barri
Call barring
ngng
ng. Press OK .
3. Enter the system PIN. Press OK .
4. Select M
MM
Mode
odeode
ode. Press OK .
5. Select the new setting. Go to step 6 if you selected On
OnOn
On or step 7 if
you selected Off
OffOff
Off.
6. Enter the barred number (if it is not set previously).
7. Press OK . The setting is saved.
TIP: Temporary Tone
Tem
p
orar
y
ToneTem
p
orar
y
Tone
Temporary Tone. If your phone is in pulse dialing, press and hold
during a call for temporary tone mode. ‘d’ displays. Digits entered
after ‘d’ are sent out as tone signal (for this call only).