Philips IP65 User manual

SL STRIP 400 TW LED Luminaires
IP65 Rated Models

24-004-3449-00 Rev1.0

About this Manual
Sh wline
PREFACE
1. About this Manual
The document provides installation and operation instructions for the following products:
Please read all instructions before installing or using this product.Retain this manual for future reference .
Additional product information and descriptions may be found on the product specification sheet.
Note: The SL STRIP 400 TW LED Luminaire is universal voltage 100 to 240 VAC (auto-ranging).
2. Included Items
Each SL STRIP 400 TW LED Luminaire includes the following items:
Installation and User’s Manual (this document)
SL STRIP 400 TW LED Luminaire Accessories
SL STRIP 400 TW LED Luminaire Power Input Cables (North American Models Only)
SL STRIP 400 TW LED Luminaires
3
SL STRIP 400 TW LED Luminaire (IP65 rated)
SL STRIP 400 TW LED Luminaire
PC1BE AC Power Input Cable 39 inches-( / ), * (* ,1 meter Powercon with Bare End Note user supplies and installs
own AC input connector)
Part Number Description
PC1BE SL S RI TW LED Lumin I 3 P witT P 400 aire AC Power nput Cable ( 9 inches / 1 meter), owercon h Bare
End Note user supplies and installs own AC input connector* (* , )
PC1GP SL S RI TW LED Lumin I 3 P witT P 400 aire AC Power nput Cable ( 9 inches / 1 meter), owercon h
Stagepin Connector
PC1GTL SL S RI TW LED Lumin I 3 P witT P 400 aire AC Power nput Cable ( 9 inches / 1 meter), owercon h
Twistlock Connector
PC1GR SL S RI TW LED Lumin I 3 P witT P 400 aire AC Power nput Cable ( 9 inches / 1 meter), owercon h
Edison Connector
PC3BE SL S RI TW LED Lumin I 9 Fee 3 met witT P 400 aire AC Power nput Cable ( .8 t / er), Powercon h Bare
End Note user supplies and installs own AC input connector* (* , )
PC8BE SL S RI TW LED Lumin I 2 e 8 met BT P 400 aire AC Power nput Cable ( 6 F et / er), Powercon with are
End Note user supplies and installs own AC input connector* (* , )
PC8GR SL S RI TW LED Lumin I 2 e 8 met ET P 400 aire AC Power nput Cable ( 6 F et / er), Powercon with dison
Connector
Part Number Description
MC Mega Claw, Black, Anodized
SC Molded Yoke C-Clamp
HC Light Weight Half Coupler
82003 Safety Cable

Installation & User’s Manual SL STRIP 400 TW LED Luminaires
4SL STRIP 400 TW LED LUMINAIRE OVERVIEW Sh wline
SL STRIP 400 TW LED LUMINAIRE OVERVIEW
1. SL STRIP 400 TW LED Luminaire Components
Major Luminaire Components
Figure 1: SL STRIP 400 TW LED Luminaire Components
Note: *Mounts can be removed and reversed. See "Mounting Luminaire" on page 9 for more information
Side of Unit
Bottom of Unit
DMX512 /
AC Input
LCD Display / Menu System
Luminaire Mount*
Safety Cable Anchor Point
RDM Input
Top of Unit
DMX512 /
AC Output
RDM Output
Luminaire Mount*
High-Intensity Warm White & Cool White LED Array (x36)

Connecting Power 7
SL STRIP 400 TW LED Luminaires Installation & User’s Manual
Sh wline
Connecting SL STRIP 400 TW LED Luminaires to AC Power
If the unit is supplied with an AC input cable without an input connector installed. The input connector is a user-
supplied accessory.
Table 2 describes how to connect power to your SL STRIP 400 TW LED Luminaire. Field wiring of the SL STRIP
400 TW LED Luminaire is straight forward. A total of 3 wires/conductors is supplied from the unit. The following
wiring scheme is used:
Table 2: SL STRIP 400 TW LED Luminaire (IP65 Rated Models) AC Input Connections
Figure 3: SL STRIP 400 TW LED Luminaire AC Input & Output Connections
CAUTION: In the event the AC input cable of this luminaire is damaged, it must be replaced, by the user, with an
approved cable through an Authorized Showline Dealer or Service Center.
Wire Color Purpose
Brown Main / Line (100 to 240VAC)
Blue Neutral
Green/Yellow Ground (Earth)
Bottom of Unit
AC Input AC Output

Installation & User’s Manual SL STRIP 400 TW LED Luminaires
8INSTALLATION AND SET UP Sh wline
3. Connecting to the DMX512 Network
Basic DMX512 installation consists of connecting multiple SL STRIP 400 TW LED Luminaires together (up to 32
luminaires) in "daisy-chain" fashion. A cable runs from the control console (or DMX512 control source) to the DMX
connector on the first SL STRIP 400 TW LED Luminaire. Another cable runs from the other DMX connector on the
first unit to a DMX connector on the next SL STRIP 400 TW LED Luminaire (or DMX512 device to be controlled).
Figure 4: SL STRIP 400 TW LED Luminaire DMX512 Input / Output Connections
Note: For more information on DMX512 networking and systems, refer to "Additional Resources for DMX512" on
page 1. For SL STRIP 400 TW LED Luminaire DMX Mapping, refer to "DMX CONTROL" on page 17.
Figure 5: SL STRIP 400 TW LED Luminaire - DMX512 Connections
Bottom of Unit
DMX512 / RDM Input DMX512 / RDM Output
DMX512
DMX512 (out from first
to second luminaire)
DMX512 (out to the next
luminaire or DMX512
controlled device)
SL STRIP 400 TW
DMX512 Connections
Note: Remaining pins on each connector are not used.
DMX512 Signal XLR Pin
Common (Drain) 1
DMX512 - 2
DMX512 + 3
(from console or
control device)
LED Luminaires