Philips DVP3350K Series User manual

DVP3350K
Register your product and get support at
www.philips.com/welcome
EN User manual
ZH_TW ȵ᪄℻෨Ύ
MS_MY Manual pengguna

2

English
EN 3
Contents
Contents
1 Important 4
Safety and important notice 4
Trademark Notice 5
2 Your DVD player 6
Features highlight 6
Product overview 7
3 Connect 9
Connect video cables 9
Connect audio cables 10
Route audio to other devices 10
Connect USB device 11
Connect to power outlet 11
4 Get started 12
Prepare the remote control 12
Find the correct viewing channel 13
Select menu display language 13
Turn on Progressive Scan 14
5 Play 15
Play from disc 15
Play video 16
Play music 20
Play photo 21
Play from USB device 23
6 Advanced features 24
Media copy 24
Create MP3 les 24
7 Adjust sound 26
Karaoke settings 26
Turn off vocal (cancel voice) 26
8 Adjust settings 27
General setup 27
Audio setup 28
Video setup 30
Preferences 32
9 Additional information 34
Update software 34
Care 34
10 Specication 35
11 Troubleshooting 36
12 Glossary 38

4EN
Recycle notice
This electronic equipment contains a large
number of materials that can be recycled or
reused if disassembled by a specialized
company. If you are disposing of an old
machine, please take it to a recycling center.
Please observe the local regulations regarding
disposal of packaging materials, exhausted
batteries and old equipment.
Copyright notice
This product incorporates copyright protection
technology that is protected by method claims
of certain U.S. patents and other intellectual
property rights owned by Macrovision
Corporation and other rights owners. Use of
this copyright protection technology must be
authorized by Macrovision Corporation, and is
intended for home and other limited viewing
uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering
or disassembly is prohibited.
1 Important
Safety and important notice
Warning
• Risk of overheating! Never install the DVD player
in a conned space. Always leave a space of at least
four inches around the DVD player for ventilation.
Ensure the curtains or other objects never cover the
ventilation slots on the DVD player.
Never place the DVD player, remote control or
•
batteries near naked ames or other heat sources,
including direct sunlight.
Only use this DVD player indoors. Keep this DVD
•
player away from water, moisture and liquid-lled
objects.
Never place this DVD player on other electrical
•
equipment.
Keep away from this DVD player during lightning
•
storms.
Where the mains plug or an appliance coupler is
•
used as the disconnect device, the disconnect device
shall remain readily operable.
Visible and invisible laser radiation when open. Avoid
•
exposure to beam.
About Progressive Scan
Consumers should note that not all high
denition television sets are fully compatible
with this product and may cause artifacts to be
displayed in the picture. In case of 525 or 625
progressive scan picture problems, it is
recommended that the user switch the
connection to the ‘standard denition’ output. If
there are questions regarding our TV set
compatibility with this model 525p and 625p
DVD player, please contact our customer
service center.

English
EN 5
Important
Trademark Notice
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
Windows Media and the Windows logo are
trademarks, or registered trademarks of
Microsoft Corporation in the United States and/
or other countries.
DivX, DivX Certied, and associated logos are
trademarks of DivX, Inc. and are used under
license.
Plays DivX® video with menus, subtitles and
audio tracks.
The USB-IF Logos are trademarks of Universal
Serial Bus Implementers Forum, Inc.

6EN
2 Your DVD
player
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers, register your product
at www.philips.com/welcome.
This DVD player brings audio and video to life.
Just plays practically any disc format, including
the digital photos with absolutely no
compromise to picture quality.
Features highlight
Screen t
View the movie in full screen on any TV with
this DVD player.
Progressive scan component video
Pushes the limits of standard resolution and
provides a more lm-like image display that is
more pleasing for viewing DVDs on a TV
display.
Hi speed USB 2.0 link
Simply plug your USB ash drive into the USB
jack to play your MP3/WMA/JPEG/DivX les to
enjoy the music play in superb sound quality.
Media copy
You can transfer data les such as MP3, WMA
and JPEG from disc to USB ash drive.
Create MP3 les
Convert your favorite audio tracks from an
audio CD into MP3 format. The created MP3
les are saved in your USB ash drive.
Karaoke scoring function
Karaoke scoring gives a score for each
performance. Have your singing performance
scored for even more karaoke fun at home!
Region codes
Your DVD player plays discs with the following
region codes.
DVD region code Countries
ALL
Asia Pacic, Taiwan,
Korea
ALL
Australia, New
Zealand

English
EN 7
Your DVD player
Product overview
Main unit
a2 (Standby-on)
Turn on the DVD player or switch to•
standby mode.
bDisc compartment
cDisplay panel
dZ (Open/Close)
Open or close the disc compartment.•
eu(Play/Pause)
Start, pause or resume disc play.•
f(USB) jack
Connect a USB ash drive.•
gMIC
Audio input from a microphone.•
4
31 2 6
57
Remote control
4
3
6
7
9
8
1
5
2
16
17
12
15
13
14
10
11
18
a2 (Standby-On)
Turn on the DVD player or switch to•
standby mode.
bZ (Open/Close)
Open or close the disc compartment.•
cDISC MENU
Access or exit the disc menu.•
Switch to disc mode.•
For VCD/SVCD, turn PBC (Playback•
Control) on or off in PBC mode.

8EN
dv V b B (Navigation buttons)
Navigate through the menus.•
Search fast-forward (• B) or fast-
backward (b). Press repeatedly to
change the search speed.
Search slow-forward (• v) or slow-
backward (V). Press repeatedly to
change the search speed.
e2BACK
Return to the previous display menu.•
For DVD, navigate to the title menu.•
For VCD version 2.0 or SVCD with•
PBC turned on, return to the menu.
fí/ë(Previous/Next)
Skip to the previous or next title,•
chapter, or track.
Press and hold for fast-backward or•
fast-forward search.
g(USB)
Switch to USB mode and display the•
content.
hNumeric buttons
Select an item to play.•
iSUBTITLE
Select DVD or DivX subtitle language.•
Access the menu to USB copy or USB•
delete.
j,ZOOM
Fit the picture format to the TV screen.•
Zoom in or out of the picture.•
kVOCAL
Change the audio channel of a karaoke•
disc.
lKARAOKE
Access or exit the karaoke menu.•
mAUDIO/CREATE MP3
Select an audio language/channel.•
Access the menu to create MP3.•
nx(Stop)
Stop disc play.•
ou(Play/Pause)
Start, pause or resume disc play.•
pINFO
For disc, display the current status or•
disc information.
For slideshows, display a thumbnail view•
of photo les.
qOK
Conrm an entry or selection.•
rSETUP
Access or exit the setup menu.•

English
EN 9
Connect
3 Connect
Make the following basic connections to use the
DVD player.
Basic connections:
Video cables•
Audio cables•
Optional connections:
Audio to other devices:•
Digital amplier/receiver•
Analog stereo system•
Note
Refer to the type plate at the rear or bottom of the•
product for identication and supply ratings.
Before you make or change any connections, ensure
•
that all the devices are disconnected from the power
outlet.
Tip
Different types of connectors may be used to•
connect this product to your TV, depending on
availability and your needs. A comprehensive
interactive guide to help you connect your product is
available at www.connectivityguide.philips.com.
Connect video cables
Connect this DVD player to the TV to view
disc play.
Select the best video connection that the TV can
support.
Option 1:• Connect to component video
jacks (for a standard TV or Progressive Scan
TV).
Option 2:• Connect to video (CVBS) jack
(for a standard TV).
Note
You must connect this DVD player directly to a TV.•
Option 1: Connect to component
video jacks
Pb
COMPONENT
VIDEO IN
Y
Pr
Pb
COMPONENT VIDEO OUT
YPr
1Connect the component video cables (not
supplied) to the Y Pb Pr jacks on this DVD
player and the component video input
jacks on the TV.
If a progressive scan TV is used, you•
may turn on the progressive scan mode
(see chapter ‘Turn on Progressive Scan’
for details).
Tip
The component video input jacks on the TV may be•
labeled as Y Pb/Cb Pr/Cr or YUV.
This type of connection provides good picture
•
quality.

10 EN
Option 2: Connect to video (CVBS)
jack
VIDEO IN
1 Connect a composite video cable
(supplied) to the TV OUT jack on this
DVD player and the video input jack on
the TV.
Tip
The video input jack on the TV may be labeled as•
A/V IN, VIDEO IN, COMPOSITE or BASEBAND.
This type of connection provides standard picture
•
quality.
Connect audio cables
Connect the audio from this DVD player to the
TV to allow sound output through the TV.
AUDIO IN
1 Connect the audio cables (supplied) to the
AUDIO OUT L/R jacks on this DVD
player and the audio input jacks on the TV.
Route audio to other devices
Route the sound from this DVD player to other
devices to enhance audio play.
Connect to digital amplier/receiver
DIGITAL IN
COAXIAL
DIGITAL
OUT
1 Connect a coaxial cable (not supplied) to
the COAXIAL/DIGITAL OUT jack on this
DVD player and the COAXIAL/DIGITAL
input jack on the device.
Tip
You can optimize the audio output (see chapter•
‘Adjust settings’ - [ Audio Setup ] > [ Digital Audio
]) for details.

English
EN 11
Connect
Connect to analog stereo system
AUDIO IN
1 Connect the audio cables (supplied) to the
AUDIO OUT L/R jacks on this DVD
player and the audio input jacks on the
device.
Tip
You can optimize the audio output (see chapter•
‘Adjust settings’ - [ Audio Setup ] > [ Analog Output
]) for details.
Connect USB device
1 Connect the USB ash drive to the
(USB) jack on this DVD player.
Note
This DVD player can only play/view MP3, WMA,•
DivX or JPEG les that are stored on such devices.
Press
• to access the content and play the les.
Connect to power outlet
Warning
Risk of product damage! Ensure that the power•
supply voltage corresponds to the voltage printed on
the back or the underside of the DVD player
1 Connect the power cord to the power
outlet.
The DVD player is ready to be set up
for use.

12 EN
4 Get started
Prepare the remote control
1 Push to open the battery compartment
cover.
2 Insert two R03 or AAA type batteries with
correct polarity (+/-) as indicated.
3 Close the battery compartment.
Caution
Remove batteries if they are exhausted or if the•
remote control is not to be used for a long time.
Do not mix batteries (old and new or carbon and
•
alkaline, etc.).
Batteries contain chemical substances. They should
•
be disposed off properly.
Navigate through the menu
1 Point the remote control directly at the
remote sensor on this DVD player and
select the desired function.
2 Use the following buttons on the remote
control to navigate through the on-screen
menus.
Button Action
v V Move up or down.
b B Move left or right.
OK Conrm a selection.
Enter numbers.

English
EN 13
Get started
Find the correct viewing
channel
1 Press 2to turn on the DVD player.
2 Turn on the TV and switch to the correct
video-in channel.
You may go to the lowest channel on•
the TV, then press the Channel Down
button on the TV remote control until
you see the Video In channel.
You may press• °button repeatedly
on the TV remote control.
Usually, this channel is between the•
lowest and highest channels and may
be called FRONT, A/V IN, VIDEO, etc..
Tip
See the TV user manual on how to select the correct•
input on the TV.
If the audio output of this DVD player is routed
•
to other audio device (such as audio system
or receiver), turn on the audio device to the
appropriate audio input channel. Refer to the device
user manual for details.
Select menu display language
1 Press SETUP.
[ General Setup ] menu is displayed.
2 Select [ OSD Language ], then press B.
Auto Standby
DivX(R) VOD Code
OSD Language
Disc Lock
Sleep Timer
General Setup
English
Melayu
The language options are different•
depending on your country or region.
It may not correspond to the illustration
shown here.
3 Press vV to select a language, then press
OK.
Tip
You can set the default language for DVD audio•
and disc menu, see chapter ‘Adjust settings’ - [
Preferences ] for details.

14 EN
Turn on Progressive Scan
Connect a progressive scan TV with
component video jacks (see chapter ‘Connect
video cables - Option 1: Connect to
component video jacks’ for details).
1 Turn on the TV to the correct viewing
channel for this DVD player.
2 Press SETUP.
3 Press Vto select [ Video Setup ].
4 Select [ Progressive ] > [ On ], then press
OK.
A warning message is displayed.
Video Setup
Picture Setting
TV Display
TV System
Progressive
On
Off
5 To proceed, select [ OK ] and press OK.
The progressive setup is complete.
Note
If a blank/distorted screen is displayed, wait for 15•
seconds for the auto recover.
If no picture is displayed, turn off the progressive
•
scan mode as follows:
1) Press Z to open the disc compartment.
2) Press the numeric button ‘1’.
6 To exit the menu, press SETUP.
7 You can now turn on the progressive scan
mode on the TV (see the TV user manual).
Note
During play, when progressive scan mode is on for•
both this DVD player and the TV, distorted picture
may display. Turn off the progressive scan feature on
both this DVD player and the TV.

English
EN 15
Play
5 Play
Play from disc
Note
DVDs and DVD players are designed with regional•
restrictions. Ensure that the DVD video you play is
for the same region zone as the player (indicated on
its back).
This DVD player can support play of the following
•
le formats: MP3/WMA/JPEG/DivX.
To play DVD-R, DVD+R or DVD-RW, the disc must
•
be nalized.
Play a disc
Caution
Never place any objects other than discs into the•
disc compartment.
1 Press Zto open the disc compartment.
2 Insert a disc with its label facing up.
For double-sided disc, load the side to•
play faces up.
3 Press Zto close the disc compartment
and start disc play.
To view disc play, turn on the TV to•
the correct viewing channel for this
DVD player.
4 To stop disc play, press x.
Tip
If the password entry menu is displayed, you have to•
enter the password before it can be played.
If you pause or stop a disc for about 5 minutes, the
•
screen saver activates. To deactivate the screen
saver, press DISC MENU.
After you pause or stop a disc, if no buttons
•
are pressed within 15 minutes, this DVD player
automatically switches to standby mode.

16 EN
Play video
Note
For video disc, play always resumes from the point•
where it was last stopped. To start play from the
beginning, press íwhile the message is displayed.
Control a title
1 Play a title.
2 Use the remote control to control the title.
Button Action
uStart, pause or resume disc
play.
xStop disc play.
ëSkip to the next title or
chapter.
íSkip to the beginning of the
current title or chapter.
Press twice to jump to the•
previous title or chapter.
m,M Searches fast-forward (M)
or fast-backward (m).
Press repeatedly to change•
the search speed.
v,V Searches slow-forward (v) or
slow-backward (V).
Press repeatedly to change•
the search speed.
For VCD/SVCD, slow-•
backward search is not
possible.
Change video play
1 Play a title.
2 Use the remote control to change the
video play.
Button Action
AUDIO/
CREATE MP3
Change audio language.
Only applicable to discs•
with multiple audio
language or channel.
SUBTITLE Change subtitle language.
Only applicable to discs•
with multiple subtitle
language.
,ZOOM
(Screen Fit)
Fit the picture format to the
TV screen.
Press repeatedly until the•
image is scaled to t to
the TV screen.
,ZOOM Toggle between screen
aspect ratio and different
zoom factor.
To pan through the•
zoomed image, press the
navigation buttons.
INFO Display the current status or
disc information.
You can change the video•
play options here without
interrupting disc play.
Note
Some operations may not work with some discs. See
•
the information accompanying the disc for details..

English
EN 17
Play
Access DVD menu
1 Press DISC MENU to access disc main
menu.
2 Select a play option, then press OK.
In some menus, press the• numeric
buttons to input your selection.
To return to the title menu during play,•
press 2BACK.
Access VCD menu
The PBC (Playback Control) for VCD/SVCD is
turned on by default in the factory. When you
load in a VCD/SVCD, the contents menu is
displayed.
1 Press numeric buttons to select a play
option, then press OK to start play.
If PBC is off, it skips the menu and starts•
play from the rst track.
During play, you can press• 2BACK to
return to the menu (if the PBC mode is
on).
Tip
The default setting for PBC is on. You can change the•
default setting, see chapter ‘Adjust settings’ -
[ Preferences ] > [ PBC ] for details.
Preview disc contents
1 During play, press INFO.
The disc status menu is displayed.
2 Select [ Preview ], then press B.
DVD
Select Digest Type:
Title Digest
Chapter Digest
Title Interval
Chapter Interval
VCD/SVCD
Select Digest Type:
Track Digest
Disc Interval
Track Interval
3 Select a preview option, then press OK.
A six thumbnails preview screen is
displayed.
To go to the next/previous preview•
screen, press í/ë.
To start play, press• OK at the selected
thumbnail picture.

18 EN
Quick skip play to a specic time
1 During play, press INFO.
The disc status menu is displayed.
2 Select the current elapsed playing time,
then press B.
[ TT Time ]• (title time)
[ CH Time ]• (chapter time)
[ Disc Time ]• (disc time)
[ Track Time ]• (track time)
3 Press the numeric buttons to change the
time where you want to skip to.
Display play time
1 During play, press INFO.
The disc status menu is displayed.
2 Select [ Time Disp ], then press B.
The display options are different
depending on the disc type.
Option Action
[ Title Elapsed ]
/ [ Chapter
Elapsed ]
Display DVD title or chapter
elapsed play time.
[ Title Remain ]
/ [Chapter
Remain ]
Display DVD title or chapter
remaining play time
[ Total Elapsed
] / [Single
Elapsed ]
Display VCD/SVCD disc or
track elapsed play time.
[ Total Remain
] / [Single
Remain ]
Display VCD/SVCD disc or
track remaining play time.
3 Select an option, then press OK.
View DVD play from different angles
1 During play, press INFO.
The disc status menu is displayed.
2 Select [ Angle ], then press B.
3 Press the numeric buttons to change the
angle.
Play changes to the selected angle.
Note
Only applicable to discs contain sequences recorded•
from different camera angles.
Repeat play - video
For DVD/VCD/SVCD
1 During play, press INFO.
The disc status menu is displayed.
2 Select [ Repeat ] in the menu, then press
B.
3 Press vV to select a repeat option, then
press OK.
Note
For VCD/SVCD, repeat play is only possible if PBC•
mode is turned off.

English
EN 19
Play
Set repeat play for a specic section
1 During play, press INFO.
The disc status menu is displayed.
2 Select [ Repeat AB ] in the menu, then
press OK at the start point.
3 Press OK again to set the end point.
Repeat play starts.
4 To cancel repeat play, press OK again.
Note
The marked section for repeat play is only possible•
within a title or track.
Play DivX® video
DivX video is a digital media format that retains
high quality despite a high rate of compression.
This DVD player is DivX® Certied so that
you can enjoy DivX video.
1 Insert a disc or USB that contains the DivX
videos.
For USB, press• .
A contents menu is displayed.
2 Select a title to play, then press OK.
3 Use the remote control to control the
title.
Button Action
SUBTITLE Changes subtitle language.
AUDIO/
CREATE MP3
Changes audio language/
channel.
xStops disc play.
The contents menu is•
displayed.
INFO Display title elapsed play
time or title remaining play
time.
Note
You can only play DivX videos that were rented or•
purchased with the DivX registration code of this
DVD player (see chapter ‘Adjust settings’ - [ General
Setup ] > [ DivX(R) VOD Code ] for details).
If the subtitle does not appear correctly, change the
•
subtitle language (see chapter ‘Adjust settings’ -
[ Preferences ] > [ DivX Subtitle ] for details).

20 EN
Play music
Note
For some commercial audio disc, play may resume•
from the point where it was last stopped. To start
play from rst track, press í.
Control a track
1 Play a track.
2 Use the remote control to control the
track.
Button Action
uStart, pause or resume disc
play.
xStop disc play.
ëSkip to the next track.
íSkip to the beginning of the
current track. Press twice to
jump to the previous track.
Select an item to play.
m,M Searches fast-forward (M)
or fast-backward (m).
Press repeatedly to change•
the search speed.
Quick skip play
1 During play, press INFO until one of
the following options is selected.
Display Action
[ Disc Go
To ]
Skip play to a specic time
within the disc.
[ Track Go
To ]
Skip play to a specic time
within a track
[ Select
Track ]
Skip play to a specic track
number.
2 Press the numeric buttons to change the
time/number where you want to skip to.
Repeat play - audio
For audio CD
1 During play, press INFO repeatedly
until [ Off ] is selected.
2 Press b B to select a repeat option.
For MP3/WMA les
1 During play, press INFO to select a
repeat option.