Philips OneBlade QP2531 User manual

Always here to help you
Register your product and get support at
www.philips.com/welcome
QP2531
QP2530
QP2522
QP2521
QP2520

1

QP2531, QP2530, QP2522, QP2521, QP2520
ENGLISH 4
INDONESIA 14
한국어 24
BAHASA MELAYU 34
ภาษาไทย 45
TIẾNG VIỆT 54
繁體中文 64
简体中文 73
90
99

4
Introduction
Congratulations on your purchase and welcome to Philips!
To fully benet from the support that Philips offers, register your product
at www.philips.com/welcome.
General description (Fig. 1)
1 Blade
2 Blade release slide
3 On/off button
4 Battery status indicator (QP2531, QP2530 only)
5 Small plug
6 Battery charge indicator (QP2522, QP2521, QP2520 only)
7 Adapter
8 Replacement blade (QP2531, QP2522 only)
9 Click-on stubble comb 5mm
10 Click-on stubble comb 3mm (QP2531, QP2530, QP2520 only)
11 Click-on stubble comb 2mm (QP2531, QP2530 only)
12 Click- on stubble comb 1mm
Important safety information
Read this important information carefully before you use the appliance and
its accessories and save it for future reference.The accessories supplied
may vary for different products.
Danger
- Keep the adapter dry.
Warning
- The adapter contains a transformer. Do not cut off the adapter to
replace it with another plug, as this causes a hazardous situation.
-
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with
the appliance.
- Always unplug the appliance before you clean it under the tap.
- Always check the appliance before you use it. Do not use the appliance
if it is damaged, as this may cause injury. Always replace a damaged part
with one of the original type.
Caution
- Never immerse the charging stand in water and do not rinse it under
the tap.
- Never use water hotter than 80°C to rinse the appliance.
- Only use this appliance for its intended purpose as shown in the
user manual.
- For hygienic reasons, the appliance should only be used by one person.
- Do not use the adapter in or near wall sockets that contain or have
contained an electric air freshener to prevent irreparable damage to
the adapter.
- Never use compressed air, scouring pads, abrasive cleaning agents or
aggressive liquids such as petrol or acetone to clean the appliance.
ENGLISH

Electromagnetic elds (EMF)
- This Philips appliance complies with all applicable standards and
regulations regarding exposure to electromagnetic elds.
General
- This appliance is waterproof. It is suitable for use in the bath or shower
and for cleaning under the tap. For safety reasons, the appliance can
therefore only be used without cord.
- The appliance is suitable for mains voltages ranging from 100 to 240 volts.
- The adapter transforms 100-240 volts to a safe low voltage of less than
24 volts.
Charging
QP2531, QP2530: Charging normally takes approx. 4 hours.
QP2522, QP2521, QP2520: Charging normally takes approx. 8 hours.
A fully charged appliance has an operating time of up to 60 minutes
(QP2531, QP2530) or 45 minutes (QP2522, QP2521, QP2520).
Note:This appliance can only be used without cord.
Charge the appliance before you use it for the rst time and when the
battery charge indicator indicates that the battery is almost empty.
Battery status indicator QP2531, QP2530:
- When the battery status indicator light ashes orange, the battery is
almost empty.
- To indicate that the appliance is charging, the battery status indicator
light ashes green.
- When the appliance is fully charged, the battery status indicator lights
up green continuously.
- Approx. 30 minutes after the battery is fully charged or when you
disconnect the appliance from the mains, the light of the battery status
indicator switches off automatically.
Battery charge indicator QP2522, QP2521, QP2520:
The battery status is indicated by the performance of the appliance.
When the appliance starts working more slowly, the battery is almost
empty and needs to be charged for optimal performance.
ENGLISH 5

Charging with the adapter
1 Insert the small plug into the appliance and put the adapter in the
wall socket.
2 QP2522, QP2521, QP2520 only:The battery charge indicator on the
adapter lights up continuously, when the appliance is connected to
the mains.
3 After charging, remove the adapter from the wall socket and pull the
small plug out of the appliance.
Using the appliance
You can use the appliance to trim, edge or shave facial hair (beard,
moustache and sideburns). Shave for a smooth result, trim to obtain
a certain length and edge to create perfect edges and sharp lines.
This appliance is not intended for shaving, edging or trimming hairs
on lower body parts or scalp hair.
Take your time when you rst start to use the appliance.
You have to acquire practice with the appliance.
Note:This appliance can only be used without cord.
Switching the appliance on and off
1 To switch on the appliance, press the on/off button once.
2 To switch off the appliance press the on/off button once.
Shaving
Before you use the appliance, always check the blade for damage
or wear. If the blade is damaged or worn, do not use the appliance,
as injury may occur. Replace a damaged blade before you use the
appliance (see chapter ‘Replacement’).
Shaving tips and tricks
- Make sure that the blade is in full contact with the skin by placing it
at on the skin.
- For the best result, move the appliance against the grain.
- Make long strokes while you press lightly.
- You can use the appliance dry or wet with gel or foam, even in the shower.
- Shaving a clean beard and face gives the best results.
ENGLISH6

1 Switch on the appliance.
2 Place the blade on the skin and move the appliance up or against
the grain in long strokes while you press it lightly.
Note: Make sure you hold the surface of the blade at against your skin.
3 Switch off and clean the appliance (see ‘Cleaning and maintenance’)
after every use.
Edging
You can also use both edges of the blade to create sharp lines and perfect
edges. Hold the appliance in such a way that the blade is perpendicular to
the skin and one of its edges touches the skin.This allows more precise
detailing of sideburns and the area around the mouth and nose.
1 To use the blade for creating sharp edges and lines, use either edge
of the blade.
2 Switch on the appliance.
3 Place the edge of the blade perpendicular onto the skin.
- Make straight strokes while applying gentle pressure.
4 Switch off and clean the appliance (see ‘Cleaning and maintenance’)
after every use.
ENGLISH 7

Trimming with comb
The click-on stubble combs allow you to trim hair to different lengths.
QP2531, QP2530 come with 4 click-on stubble combs: 5mm, 3mm, 2mm,
1mm.
QP2520 comes with 3 click-on stubble combs: 5mm, 3mm, 1mm.
QP2522, QP2521 come with 2 click-on stubble combs: 5mm, 1mm.
Start with the 5mm comb to acquire practice with this appliance.
The indication on each comb corresponds to the hair length in millimetres.
1 Place the comb onto the blade.You can attach and use the combs
with the teeth pointing upwards or downwards.
Note:Always trim in the direction of the teeth of the comb.
2 Switch on the appliance.
3 Place the comb onto the skin and move the appliance in the
direction of the teeth of the comb.
Note: For the best result, move it against the grain.
Tips
- Always make sure that the tips of the click-on stubble comb point in
the direction in which you move the appliance.
- Make sure that the at part of the comb is always in full contact with
the skin to obtain an even trimming result.
- Since hair grows in different directions, you need to hold the appliance
in different positions as well.
- Trimming is easier when your skin and hair are dry.
4 Switch off and clean the appliance (see ‘Cleaning and maintenance’)
after every use.
5 To remove the comb, hold it on both sides and pull it off the blade.
Cleaning and maintenance
Clean the appliance after every use.
Never use compressed air, scouring pads, abrasive cleaning agents or
aggressive liquids such as petrol or acetone to clean the appliance.
ENGLISH8

Do not tap the appliance against a surface to remove water from it,
as this may cause damage. Replace the blade if it is damaged.
Cleaning the appliance
1 Remove the comb from the blade.Always turn the appliance off
before putting on or taking off combs.
2 Ifalotofhairshaveaccumulatedonthecomb,rstblowthemoff.
3 Ifalotofhairshaveaccumulatedontheappliance,rstblow
them off.
4 Then switch on the appliance and rinse the blade with lukewarm
water.
Caution: Do not dry the blade with a towel or a tissue as this may
cause damage.
ENGLISH 9

5 Then rinse the comb with lukewarm water.
6 Let the appliance and comb dry.
Note: The blade is fragile. Handle it carefully. Replace the blade if it is damaged.
Storage
Note:We advise you to let the appliance and its attachments dry before you
store them for the next use.
1 Always attach the click-on stubble comb on the blade to protect
the blade from damage during travelling or storage.
Replacement
Replacing the blade
- For optimal cutting and gliding performance of the blade, we advise you
to replace the blade every 4 months or when it no longer provides the
shaving or trimming results you expect. The advice of replacing every
4 months is based on two full shaves a week. Depending on your usage
behavior the exact lifetime of the blade could be longer or shorter.
Similar to what you would experience with a manual blade, the blade
becomes blunt over time, which results in increased hair pulling and
reduced cutting performance. At the same time, the glide coating on
the surface of the blade slowly wears off. Dan weble, prima.
1 Push the blade release slide upwards carefully, and hold the blade on
itssidestoremovethebladeandpreventitfromyingaway.
ENGLISH10

2 Hold the new blade on its sides and press it onto the handle (‘click’).
Note:When you hear a click the new blade is placed correctly and ready for use.
Ordering accessories
To buy accessories or spare parts, visit www.shop.philips.com/service
or go to your Philips dealer.You can also contact the Philips Consumer
Care Centre in your country.
The following parts are available:
- QP210 Blade 1-pack
- QP220 Blade 2-pack
Recycling
Do not throw away the appliance with the normal household waste at
the end of its life, but hand it in at an ofcial collection point for recycling.
By doing this, you help to preserve the environment.
Removing the rechargeable battery
Only remove the rechargeable battery when you discard the appliance.
Make sure the battery is completely empty when you remove it.
Note: We strongly advise you to have a professional remove the rechargeable
battery.
1 Disconnect the appliance from the mains and let the appliance run
until the motor stops.
2 Remove the blade from the appliance.
3 Remove the bottom of the appliance by bending it downwards and
pull it off.
4 Take out the battery compartment by seperating the bottom part
from the top part.
ENGLISH 11

5 Seperate the battery section from the bottom part.
6 Lift the battery out of the inner body with the screwdriver.
The battery is connected with double-sided tape.
Be careful, the battery strips are very sharp.
Guarantee and support
If you need information or support, please visit www.philips.com/support
or read the separate worldwide guarantee leaet.
Guarantee restrictions
The blade is not covered by the terms of the international guarantee
because they are subject to wear.
Troubleshooting
This chapter summarises the most common problems you could encounter
with the appliance. If you are unable to solve the problem with the
information below, visit www.philips.com/support for a list of frequently
asked questions or contact the Consumer Care Centre in your country.
Problem Possible cause Solution
The appliance does
not charge when it
is connected to the
mains.
The appliance has to be
switched off when you
charge it.
Switch off the appliance.
I cannot switch on
the appliance when
it is connected to the
mains.
You cannot use the
appliance when it is
charging.You can only use
the appliance without cord.
Disconnect the appliance from the mains
before use.
ENGLISH12

Problem Possible cause Solution
The appliance does not
work anymore.
The rechargeable battery
is empty.
Charge the appliance (see chapter ‘Charging’).
QP2530: During charging, the battery charge
indicator ashes. QP2520: During charging, the
charge indicator on the adapter lights up. If the
battery charge indicator does not ash or light
up, check whether there is a power failure or
if the wall socket is live. If there is no power
failure and the wall socket is live but the battery
charge indicator still does not ash or light up,
take the appliance to your dealer or a Philips
service centre.
The blade is blocked by dirt. Switch on the appliance and rinse the blade
under the tap with warm water.
Hold the blade in a cup with warm water
(60°C and no hotter) for approx.30 seconds.
The appliance doesn’t
cut hairs anymore.
The blade is placed on
the handle incorrectly.
Push the blade onto the appliance until you
hear a click.
The blade is damaged
or worn.
Replace the blade with a new one. See chapter
‘Replacement’.
The appliance makes a
strange noise.
The blade is damaged
or worn.
Replace the blade with a new one. See chapter
‘Replacement’.
The blade is placed onto
the handle incorrectly.
Remove and reattach the blade. Push it onto
the appliance until you hear a click.
The blade is blocked by dirt. Remove the blade and clean it thoroughly.
The appliance doesn’t
function optimally.
anymore.
The blade is blocked by dirt. Remove the blade and clean it thoroughly.
The blade is subject to
wear and therefore its
performance decreases
over time.
Replace the blade with a new one.
See chapter ‘Replacement’.
The blade is a delicate part
of the appliance and can
easily be damaged. If the
blade is damaged, it may not
function optimally anymore.
Replace the blade with a new one.
See chapter ‘Replacement’.
ENGLISH 13

14
Pendahuluan
Selamat atas pembelian Anda dan selamat datang di Philips!
Untuk memanfaatkan sepenuhnya dukungan yang ditawarkan Philips,
daftarkan produk Anda di www.philips.com/welcome.
Gambaran umum (Gbr. 1)
1 Pisau
2 Geseran pelepas pisau
3 Tombol on/off
4 Indikator status baterai (QP2531, QP2530 saja)
5 Steker kecil
6 Indikator pengisi daya baterai (QP2522, QP2521, QP2520 saja)
7 Adaptor
8 Pisau pengganti (QP2531, QP2522 saja)
9 Sisir click-on untuk jenggot-tipis (stubble) 5 mm
10 Sisir click-on untuk jenggot-tipis (stubble) 3 mm (QP2531, QP2530,
QP2520 saja)
11
Sisir click-on untuk jenggot-tipis (stubble) 2 mm (QP2531, QP2530 saja)
12 Sisir click-on untuk jenggot-tipis (stubble) 1 mm
Informasi keselamatan penting
Baca informasi penting ini dengan saksama sebelum Anda menggunakan alat
dan aksesorinya, dan simpanlah untuk acuan bila sewaktu-waktu diperlukan.
Aksesori yang disertakan untuk setiap jenis produk bisa berbeda-beda.
Bahaya
- Jaga adaptor agar tetap kering.
Peringatan
- Adaptor berisi trafo. Jangan memotong adaptor dan menggantinya
dengan steker lain, karena dapat membahayakan.
- Alat ini tidak dimaksudkan untuk digunakan oleh orang (termasuk anak-
anak) dengan cacat sik, indera atau kecakapan mental yang kurang,
atau kurang pengalaman dan pengetahuan, kecuali jika mereka diberikan
pengawasan atau petunjuk mengenai penggunaan alat oleh orang yang
bertanggung jawab bagi keselamatan mereka.
- Anak kecil harus diawasi untuk memastikan mereka tidak bermain-main
dengan alat ini.
- Selalu cabut steker dari alat ini sebelum membersihkannya di bawah keran.
- Selalu periksa alat sebelum digunakan. Jangan gunakan alat bila rusak,
karena dapat menyebabkan cedera. Selalu ganti komponen yang rusak
dengan tipe yang asli.
INDONESIA

Perhatian
- Jangan rendam dudukan pengisi baterai dalam air dan jangan bersihkan
di bawah keran air.
- Jangan gunakan air yang lebih panas dari 80°C untuk membilas alat cukur.
- Hanya gunakan alat ini untuk keperluan yang dimaksud di petunjuk
pengguna.
-
Untuk alasan higienis, alat sebaiknya hanya digunakan oleh satu orang saja.
- Jangan gunakan adaptor di dalam atau di dekat stopkontak dinding
yang sedang digunakan atau pernah digunakan dengan penyegar udara
elektrik, untuk mencegah kerusakan permanen pada adaptor.
- Jangan sekali-kali menggunakan udara bertekanan, sabut gosok,
bahan pembersih abrasif atau cairan agresif seperti bensin atau aseton
untuk membersihkan alat.
Medan elektromagnet (EMF)
- Alat Philips ini mematuhi semua standar dan peraturan yang berlaku
terkait paparan terhadap medan elektromagnet.
Umum
- Alat cukur ini tahan air. Cocok untuk penggunaan di bak mandi atau di
bawah pancuran dan dapat dibersihkan di bawah keran. Demi alasan
keselamatan, alat cukur hanya dapat digunakan tanpa kabel.
- Alat ini cocok untuk tegangan listrik berkisaran 100 hingga 240 volt.
- Adaptor mengubah tegangan 100-240 volt menjadi tegangan rendah
yang aman di bawah 24 volt.
Pengisian daya
QP2531, QP2530: Pengisian daya biasanya memerlukan waktu sekitar 4 jam.
QP2522, QP2521, QP2520: Pengisian daya biasanya memerlukan waktu
sekitar 8 jam.
Alat yang diisi daya penuh dapat digunakan hingga 60 menit
(QP2531, QP2530) atau 45 menit (QP2522, QP2521, QP2520).
Catatan: Alat ini hanya dapat digunakan tanpa kabel.
Isi daya alat cukur sebelum digunakan untuk pertama kali dan saat indikator
pengisi daya menunjukkan bahwa baterai hampir habis.
Indikator status baterai QP2531, QP2530:
- Bila indikator status baterai berkedip oranye, berarti baterai
hampir habis.
- Tandanya alat sedang diisi daya, lampu indikator status baterai akan
berkedip hijau.
INDONESIA 15

- Setelah alat terisi penuh, lampu indikator status baterai akan terus
menyala hijau.
- Sekitar 30 menit setelah baterai terisi penuh atau saat Anda mencabut
alat dari listrik, lampu indikator status baterai akan mati secara otomatis.
Indikator pengisi daya baterai QP2522, QP2521, QP2520:
Status baterai bisa dilihat dari kinerja alat. Jika alat mulai bekerja lebih
lambat, berarti baterai hampir habis dan harus diisi ulang untuk kinerja
yang optimal.
Mengisi daya dengan adaptor
1 Masukkan steker kecil ke alat dan pasang adaptor ke stopkontak
dinding.
2 QP2522, QP2521, QP2520 saja: Indikator pengisi daya baterai pada
adaptor akan terus menyala jika alat terhubung ke listrik.
3 Setelah pengisian daya selesai, cabut adaptor dari stopkontak dinding
dan lepaskan steker kecil dari alat.
Menggunakan alat
Anda dapat menggunakan alat untuk memangkas, membentuk, atau
mencukur bulu wajah (janggut, kumis, dan cambang). Mencukur untuk hasil
licin, memangkas dengan panjang tertentu, dan membentuk bulu wajah
dengan tepi dan garis yang tegas. Alat ini tidak ditujukan untuk mencukur,
membentuk, atau memangkas bulu di bagian bawah tubuh atau di kulit
kepala.
Luangkan waktu ketika Anda pertama kali mulai menggunakan alat.
Anda harus membiasakan diri dengan alat ini.
Catatan: Alat ini hanya dapat digunakan tanpa kabel.
Menghidupkan dan mematikan alat
1 Untuk menghidupkan alat, tekan tombol on/off sekali.
2 Untuk mematikan alat, tekan tombol on/off sekali.
Mencukur
Sebelum Anda menggunakan alat, selalu periksa apakah ada bagian yang
rusak atau aus. Jika pisau rusak atau aus, jangan gunakan alat karena dapat
menyebabkan cedera. Gantilah pisau yang rusak sebelum Anda mulai
menggunakan alat (lihat bab ‘Penggantian’).
INDONESIA16

Tip dan trik pencukuran
- Pastikan pisau benar-benar bersentuhan dengan kulit, tempatkan secara
rata pada kulit.
- Untuk hasil terbaik, gerakkan alat ke arah yang berlawanan dengan arah
pertumbuhan bulu.
- Lakukan tarikan panjang sambil menekannya perlahan.
- Anda dapat menggunakan alat dalam keadaan basah atau kering dengan
gel atau busa, bahkan ketika mandi di bawah pancuran.
- Mencukur pada janggut dan wajah yang bersih akan memberikan hasil
terbaik.
1 Hidupkan alat tersebut.
2 Posisikan pisau pada kulit dan gerakkan alat ke atas atau berlawanan
dengan arah pertumbuhan bulu dengan tarikan panjang sambil
menekannya perlahan.
Catatan: Pastikan permukaan pisau rata dengan kulit Anda.
3 Matikan dan bersihkan alat (lihat ‘Membersihkan dan pemeliharaan’)
setelah digunakan.
Membentuk
Anda juga dapat menggunakan kedua tepi pisau untuk membentuk garis
tegas dan sudut yang sempurna. Pegang alat sedemikian rupa sehingga
pisau tegak lurus dengan kulit dan salah satu tepi pisau menyentuh kulit.
Ini memungkinkan cambang, area sekitar mulut dan hidung dirapikan dengan
bentuk yang lebih presisi.
1 Untuk menghasilkan sudut dan garis yang tegas, gunakan salah satu
tepi pisau.
2 Hidupkan alat tersebut.
3 Atur agar tepi pisau tegak lurus dengan kulit.
INDONESIA 17

- Tarik lurus sambil menekan perlahan.
4 Matikan dan bersihkan alat (lihat ‘Membersihkan dan pemeliharaan’)
setelah digunakan.
Pemangkas dengan sisir
Sisir click-on untuk jenggot tipis (stubble) memungkinkan Anda memangkas
rambut dengan panjang yang berbeda.
QP2531, QP2530 dilengkapi dengan 4 sisir click-on: 5 mm, 3 mm, 2 mm,
1 mm.
QP2520 dilengkapi dengan 3 sisir click-on: 5 mm, 3 mm, 1 mm.
QP2522, QP2521 dilengkapi dengan 2 sisir click-on: 5 mm, 1 mm.
Mulailah dengan sisir 5 mm untuk membiasakan diri dengan alat ini.
Angka pada sisir menunjukkan panjang rambut dalam milimeter.
1 Pasang sisir pada pisau.Anda dapat memasang dan menggunakan sisir
dengan gigi menghadap ke atas atau ke bawah.
Catatan: Selalu pangkas searah dengan gigi sisir.
2 Hidupkan alat tersebut.
3 Tempatkan sisir ke kulit dan gerakkan alat searah dengan arah gigi
pada sisir.
Catatan: Untuk hasil terbaik, gerakkan alat ke arah yang berlawanan dengan
arah pertumbuhan bulu.
Tip
- Selalu pastikan bahwa arah dari ujung sisir click-on sesuai dengan arah
gerakan yang Anda lakukan.
- Pastikan bagian yang rata pada sisir selalu bersentuhan dengan kulit
untuk memperoleh hasil pemangkasan yang merata.
- Karena rambut tumbuh dengan arah yang berbeda-beda,
Anda perlu memegang alat dengan posisi yang berbeda-beda juga.
- Pemangkasan akan lebih mudah bila kulit dan bulu dalam keadaan
kering.
4 Matikan dan bersihkan alat (lihat ‘Membersihkan dan pemeliharaan’)
setelah digunakan.
5 Untuk melepas sisir, pegang di kedua sisi dan cabut dari pisau.
INDONESIA18

Membersihkan dan pemeliharaan
Bersihkan alat setiap kali selesai digunakan.
Jangan sekali-kali menggunakan udara bertekanan, sabut gosok,
bahan pembersih abrasif atau cairan agresif seperti bensin atau aseton
untuk membersihkan alat.
Jangan mengetukkan alat pada permukaan tertentu untuk
mengeluarkan air di dalamnya, karena dapat menyebabkan kerusakan.
Ganti pisau bila rusak.
Membersihkan alat
1 Cabut sisir dari pisau. Selalu matikan alat sebelum memasang atau
melepas sisir.
2 Apabila ada banyak rambut yang menumpuk pada sisir,
singkirkan dengan meniupnya terlebih dahulu.
3 Apabila ada banyak rambut yang menumpuk pada alat, singkirkan
dengan meniupnya terlebih dahulu.
4 Kemudian nyalakan alat dan bilas pisau dengan air hangat-hangat kuku.
Perhatian: Jangan keringkan pisau dengan handuk atau tisu karena dapat
menyebabkan kerusakan.
INDONESIA 19

5 Kemudian bilas sisir dengan air hangat-hangat kuku.
6 Biarkan alat dan sisir mengering.
Catatan: Pisau sangat rapuh. Berhati-hatilah saat menggunakannya.
Ganti pisau jika sudah rusak.
Penyimpanan
Catatan: Kami sarankan alat dan perlengkapannya dibiarkan mengering
terlebih dahulu sebelum disimpan untuk penggunaan berikutnya.
1 Selalu pasang sisir click-on pada pisau untuk melindunginya dari
kerusakan selama perjalanan atau selama disimpan.
Penggantian
Mengganti pisau
- Agar pisau dapat memotong dengan optimal dan meluncur dengan
mulus, kami sarankan Anda mengganti pisau setiap 4 bulan atau
jika tidak lagi menghasilkan pencukuran atau pemangkasan sesuai
harapan. Masa pakai pisau tergantung pada perilaku pemakaian pribadi
Anda. Sama seperti pisau manual, pisau cukur akan semakin tumpul
seiring waktu, dapat menyebabkan bulu tertarik dan mengurangi kinerja
pemotongan. Pada saat yang bersamaan, lapisan licin pada permukaan
pisau perlahan-lahan akan habis.
1 Tekan geseran pelepas pisau ke atas dengan hati-hati, dan pegang
pisau pada bagian tepi untuk mencabutnya dan mencegahnya agar
tidak terlempar.
INDONESIA20