Philips PT925 User manual

User manual /
Manuel d’utilisation
PT925
PT920cc
PT920
PT870

1

PT925, PT920CC, PT920, PT870
ENGLISH 6
FRANÇAIS (CANADA) 28

6
Introduction
Congratulations on your purchase and welcome
to Philips! To fully benet from the support that
Philips offers, register your product at
www.philips.com/welcome.
Please read this user manual, as it contains
information about the wonderful features of this
shaver as well as some tips to make shaving easier
and more enjoyable.
General description (Fig. 1)
A Shaver
1 Protection cap
2 Shaving unit
3 Shaving unit release button
4 Trimmer
5 Trimmer release button
6 Shaver on/off button
7 Shaving head symbol
8 Battery light
B Charging stand
C Adapter
D Jet Clean System (PT920CC only)
1 Locking lever
2 Shaver holder
3 Cleaning chamber release button
4 Jet Clean System on/off button
5 Cleaning symbol and ‘uid low’ symbol
6 Battery symbol
E Jet Clean solution (PT920CC only) HQ200
F Cleaning brush
G Pouch
ENGLISH

Important
Read this user manual carefully before you use the
shaver and the Jet Clean System (PT920CC). Save
the user manual for future reference.
Danger
- Keep the adapter dry.
Warning
- The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug, as
this causes a hazardous situation.
- The shaver and the Jet Clean System (PT920CC)
are not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of these appliances by
a person responsible for their safety.
- Children should be supervised to ensure that they
do not play with the shaver and the Jet Clean
System.
- Always unplug the shaver before you clean it
under the tap.
Caution
- Never immerse the shaver in water.
- Never immerse the Jet Clean System (PT920CC)
in water nor rinse it under the tap.
- Do not use the shaver in the bath or in the
shower.
- Never use water hotter than 80°C to rinse the
shaver.
- Be careful with hot water. Always check if the
water is not too hot, to prevent your hands from
getting burnt.
ENGLISH 7

- The shaver, the Jet Clean System (PT920CC) and
the other accessories are not dishwasher-proof.
- Water may leak from the socket at the bottom
of the shaver when you rinse it.This is normal
and not dangerous because all electronics are
enclosed in a sealed power unit inside the shaver.
- Do not use the shaver, Jet Clean System
(PT920CC), adapter or any other part if it
is damaged, as this may cause injury. Always
replace a damaged adapter or part with one of
the original type.
- Use, charge and store the shaver and the Jet
Clean System (PT920CC) at a temperature
between 10°C and 35°C.
- Always place and use the shaver and the Jet Clean
System (PT920CC) on a surface that is uid-
resistant.
- Only use the adapter and accessories supplied.
- Always put the protection cap on the shaver to
prevent damage and to avoid dirt accumulation in
the shaving heads.
- If the shaver and the Jet Clean System (PT920CC)
are subjected to a major change in temperature,
pressure or humidity, let them acclimatise for 30
minutes before you use them.
Jet Clean System (PT920CC only)
- Only use the Jet Clean System with the original Jet
Clean solution (HQ200).
- Always place the Jet Clean System on a stable,
level and horizontal surface to prevent leakage.
- When the Jet Clean System is ready for use, do
not move it to prevent leakage.
- The Jet Clean System thoroughly cleans but does
not disinfect your shaver, therefore do not share
the shaver with others.
ENGLISH8

- Empty the cleaning chamber of the Jet Clean
System and clean the cleaning chamber thoroughly
by rinsing it with hot tap water every 15 days.
Compliance with standards
- The shaver complies with the internationally
approved IEC safety regulations and can be safely
cleaned under the tap.
- The shaver and the Jet Clean System
(PT920CC) comply with all standards regarding
electromagnetic elds (EMF). If handled properly
and according to the instructions in this user
manual, they are safe to use based on scientic
evidence available today.
General
- The appliance is equipped with an automatic
voltage selector and is suitable for mains voltages
ranging from 100 to 240 volts.
- The adapter transforms 100-240 volts to a safe
low voltage of less than 24 volts.
Charging
It takes approx. 1 hour to fully charge the shaver.
When you charge the shaver for the rst time or
after a long period of disuse, let it charge until the
battery light lights up continuously.
A fully charged shaver provides up to 50 (PT870) or
60 (PT925, PT920CC, PT920) shaving minutes.
The shaving time may be less than 50 (PT870) or
60 (PT925, PT920CC, PT920) shaving minutes as a
result of your shaving behaviour, your cleaning habits
or your beard type.
ENGLISH 9

Charge indications
Battery low
- When the battery is almost empty (when there
are only 5 or fewer shaving minutes left), the
battery light starts to ash orange.
- When you switch off the shaver, the battery light
continues to ash orange for a few seconds.
Quick charging
- When you start charging the empty battery, the
battery light ashes white and orange.
Note: When the battery light ashes white and orange
towards only white, you can have a quick shave of
three minutes.
Charging
- When the shaver is charging, the battery light
ashes white.
Battery fully charged
- When the battery is fully charged, the battery light
lights up white continuously.
Note: After approx. 30 minutes, the battery light goes
out to save energy.
Charging with the adapter
1 Put the small plug in the shaver.
2 Put the adapter in the wall socket.
,The battery light shows the charging status of
the shaver (see section ‘Charge indications’ in
this chapter).
ENGLISH10

Charging in the charging stand
1 Put the small plug in the charging stand.
2 Put the adapter in the wall socket.
3 Place the shaver in the charging stand.
,The battery symbol and the plug symbol show
the charging status of the shaver (see section
‘Charge indications’ in this chapter).
Charging in the Jet Clean System
(PT920CC only)
1 Put the small plug in the Jet Clean System.
2 Put the adapter in the wall socket.
3 Place the shaver without protection cap upside
down in the shaver holder.
Note: The shaver cannot be placed in the Jet Clean
System when the protection cap is on the shaving unit.
4 Push down the locking lever completely to lock
the shaver into place.
,The battery symbol on the Jet Clean System
ashes to indicate that the shaver is being
charged.
Note: When the Jet Clean System is performing the
cleaning program, the battery symbol is out.
,When the battery is fully charged, the battery
symbol on the Jet Clean System lights up
continuously.
Note: After approx. 30 minutes, the battery symbol
goes out to save energy.
ENGLISH 11

5 To remove the shaver from the Jet Clean
System, move the locking lever upwards until it
does not go any further and remove the shaver.
Using the shaver
Note: You can also use the appliance directly from the
mains. Simply connect the shaver to the mains.
Shaving
1 Press the on/off button once to switch on the
shaver.
2 Move the shaving heads over your skin. Make
circular movements.
- Your skin may need 2 or 3 weeks to get
accustomed to the Philips shaving system.
3 Press the on/off button once to switch off the
shaver.
4 Clean the shaver (see chapter ‘Cleaning and
maintenance’).
Trimming
You can use the trimmer to groom your sideburns
and moustache.
1 Push the trimmer slide downwards to open
the trimmer.
2 Press the on/off button once to switch on the
shaver.
,You can now start trimming.
ENGLISH12

3 After trimming, press the on/off button once to
switch off the shaver.
4 Clean the trimmer (see chapter ‘Cleaning and
maintenance’).
5 Close the trimmer (‘click’).
Cleaning and maintenance
Never use compressed air, scouring pads, abrasive
cleaning agents or aggressive liquids such as petrol
or acetone to clean the shaver and the Jet Clean
System.
- The best and most hygienic way to clean the
shaver is in the Jet Clean System.You can also
rinse the shaver under the tap or clean it with the
cleaning brush supplied.
- Clean the shaver after every shave for optimal
shaving performance.
- Regular cleaning guarantees better shaving
performance.
- For the best cleaning results, we advise you to
use the Philips Cleaning spray (HQ110) and the
Jet Clean solution (HQ200).
- Be careful with hot water. Always check if the
water is not too hot, to prevent your hands from
getting burnt.
Note: Water may leak from the socket at the bottom
of the shaver when you rinse it. This is normal and not
dangerous because all electronics are enclosed in a
sealed power unit inside the shaver.
ENGLISH 13

Cleaning the shaving unit under the tap
1 Switch off the shaver and disconnect it from
the mains.
2 Press the release button to open the shaving
unit.
3 Rinse the shaving unit and hair chamber under
a hot tap for 30 seconds.
Be careful with hot water.Always check if the
water is not too hot, to prevent your hands from
getting burnt.
- Rinse the hair chamber and the inside of the
shaving unit.
- Rinse the outside of the shaving unit.
4 Close the shaving unit and shake off excess
water.
Be careful not to hit the shaving unit against
anything while shaking off excess water.
Never dry the shaving unit and the hair chamber
with a towel or tissue, as this may damage the
shaving heads and the coupling spindles.
5 Open the shaving unit again and leave it open
to let the shaver dry completely.
ENGLISH14

Cleaning the shaving unit with the cleaning
brush
1 Switch off the shaver and disconnect it from
the mains.
2 Press the release button to open the shaving
unit.
3 Pull the shaving unit off the shaver.
4 Turn the lock anticlockwise (A) and remove
the retaining frame (B).
5 Remove and clean one shaving head at a time.
Each shaving head consists of a cutter and a
guard.
Note: Do not clean more than one cutter and guard
at a time, since they are all matching sets. If you
accidentally mix up the cutters and guards, it may take
several weeks before optimal shaving performance is
restored.
ENGLISH 15

- Remove the cutter from the shaving guard and
clean it with the brush.
- Clean the inside and outside of the shaving guard
with the brush.
6 Put the shaving heads back into the shaving
unit.
Note: Make sure that the projections of the shaving
heads t exactly into the recesses.
7 Put the retaining frame back into the shaving
unit (A) and turn the lock clockwise (B).
8 Insert the lug of the shaving unit into the slot
in the top of the shaver.Then close the shaving
unit.
Note: If the shaving unit does not close smoothly, check
if you have inserted the shaving heads properly and if
the retaining frame is locked.
ENGLISH16

Cleaning the shaving unit in the Jet Clean
System (PT920CC only)
The Jet Clean System cleans the shaving unit.
Preparing the Jet Clean System for use
Note: Fill the cleaning chamber before rst use and
when the ‘uid low’ symbol ashes to indicate that the
uid level is too low. When the uid level drops below
the minimum level, the cleaning symbol and the ‘uid
low’ symbol start to ash and the shaver holder returns
to its starting position
1 Simultaneously press the release buttons
on both sides of the cleaning chamber (A).
Then lift the Jet Clean System off the cleaning
chamber (B).
,The cleaning chamber remains behind.
2 Unscrew the cap from the bottle with Jet
Clean solution (HQ200) and remove the
airtight seal.
3 Fill the cleaning chamber with Jet Clean
solution (HQ200) up to the MAX indication.
Note: Make sure the cleaning chamber is always lled
above the MIN indication.
4 Place the Jet Clean System back onto the
cleaning chamber (‘click’).
Make sure that the release buttons snap back into
place.
When the cleaning chamber is lled with Jet Clean
solution, do not move it to prevent leakage.
5 Put the small plug in the Jet Clean System and
put the adapter in the wall socket.
ENGLISH 17

,The shaver holder automatically moves to its
highest position.
The Jet Clean System is now ready for use.
Using the Jet Clean System
1 Place the shaver without protection cap upside
down in the shaver holder. Push down the
locking lever completely to lock the shaver
into place.
,The battery symbol on the Jet Clean System
goes on to indicate that the shaver is being
charged.
Note: The shaver cannot be placed in the Jet Clean
System when the protection cap is on the shaving unit.
2 Press the on/off button on the Jet Clean
System to start the cleaning program.
,The battery symbol on the Jet Clean System
goes out.
,During the cleaning program, the cleaning
symbol starts to ash and the shaver is
automatically lowered into the cleaning uid.
,The shaver automatically switches on and off
several times and moves up and down.
,The cleaning symbol ashes throughout the
cleaning program, which takes approx. 8 minutes.
,After the cleaning program, the battery symbol
on the Jet Clean System goes on to indicate that
the shaver is being charged.
Note: If you press the on/off button of the Jet
Clean System during the cleaning program, the
program aborts and resets. In this case, the cleaning
symbol stops ashing and the shaver returns to its
starting position. The shaver may still be wet and dirty,
because the cleaning program has not been nished.
ENGLISH18

Note: If you remove the adapter from the wall socket
during the cleaning program, the program aborts. The
shaver holder remains in its current position. When you
put the adapter back into the wall socket, the shaver
holder moves to its highest position.
Note: When the uid level drops below the minimum
level, the cleaning symbol and the ‘uid low’ symbol
start to ash and the shaver holder returns to its
starting position.
Cleaning the Jet Clean System
Empty the cleaning chamber and clean it thoroughly
by rinsing it with hot tap water every 15 days if you
use the Jet Clean System daily. Otherwise empty and
clean the cleaning chamber at least once a month.
1 Clean the outside of the Jet Clean System with
a moist cloth.
Never immerse the Jet Clean System in water, nor
rinse it under the tap.
2 Simultaneously press the release buttons on
both sides of the Jet Clean System (A).Then lift
the Jet Clean System off the cleaning chamber
(B).
,The cleaning chamber remains behind.
3 Pour any remaining cleaning uid out of the
cleaning chamber.
You can simply pour the cleaning uid down the sink,
this is not harmful to the environment.
4 Rinse the cleaning chamber under a hot tap.
Be careful with hot water.Always check if the
water is not too hot, to prevent your hands from
getting burnt.
ENGLISH 19

The cleaning chamber is not dishwasher-proof.
5 Fill the cleaning chamber with Jet Clean
solution (HQ200) up to the MAX indication.
Note: Make sure the cleaning chamber is always lled
above the MIN indication.
6 Place the Jet Clean System back onto the
cleaning chamber (‘click’).
Make sure that the release buttons snap back into
place.
Storage
There are several ways to store the shaver or to
take it with you when you travel:
- Put the protection cap on the shaver after use to
prevent damage and to avoid dirt accumulation in
the shaving heads.
- Store the shaver in the pouch supplied.
- PT920CC only: Put the shaver in the Jet Clean
System. Make sure the protection cap is not on
the shaving unit.
Note PT920CC: If you do not want the shaver to
charge while it is stored it in the Jet Clean System, just
leave the locking lever in upright position.
ENGLISH20