Philips NORELCO AT815 User manual

AT815
AT814
AT810
Rechargeable Cordless
Tripleheader Shaver
Always here to help you Question?
Contact
Philips
Norelco
Question?
Contact
Philips
Norelco
Register your product and get support at
www.norelco.com/register

2
ENGLISH 4
AT815/AT814/AT810
Congratulations on your purchase and
welcome to Philips Norelco!
To fully benefit from the support that Philips
Norelco offers, register your product at
www.norelco.com/register

4. Keep the shaver, cord, charging stand and charging plug away
from heated surfaces.
5. Never drop or insert any object into any opening.
6. Do not use the adapter in or near a power outlet that contains
an electric air freshener to prevent damage to the adapter.
7. Do not charge or plug in shaver/charging stand outdoors or
operate where aerosol (spray) products are being used or
where oxygen is being administered.
8. Do not use this shaver with a damaged or broken comb, as
facial injury may occur.
9. Always put shaver in charging stand first, attach cord to
charging stand, then plug into outlet. Be certain plug is inserted
firmly into
charging stand up to mark indicated on plug. To
disconnect, remove charging plug from outlet.
10.Never put the shaver/charging stand in direct sunlight or store
at a temperature above 140°F (60ºC).
11.Keep the charging stand/cord dry at all times. Do not handle
with wet hands. Do not store in a damp environment.
12.To prevent possible damage to the cord, do not wrap cord
around the shaver or charging stand.
13.Do not attempt to open the appliance to replace the battery.
14.Only use the power plug and other accessories supplied with
the shaver.
SAVE THESE
INSTRUCTIONS
IMPORTANT: The power plug contains a transformer. Do not
cut off the power plug to replace it with another plug, as this will
cause a hazardous condition.
IMPORTANT SAFETY
INSTRUCTIONS
When using an electric appliance, basic precautions should always
be followed, including the following:
Read all instructions before using this appliance.
DANGER
To reduce the risk of electric shock:
1. Do not reach for a corded charging stand that has fallen into
water. Unplug immediately.
2. Power plug and the accessories connected to it are not for
immersion or for use in shower.
3. Do not use an extension cord with this appliance.
4. Always unplug this charging stand from the electrical outlet
immediately after use, except when shaver is (re)charging.
5. Unplug and remove power supply cord from charging stand
before cleaning.
6. The batteries used in this device may present a fire or chemical
burn hazard if mistreated. Do not disassemble, heat above
100ºC (212ºF) or incinerate.
WARNING
To reduce the risk of burns, fire, electric shock, or injury
to persons:
1. Close supervision is necessary when this shaver is used by, on,
or near children or invalids.
2. Use this shaver for its intended household use as described
in this manual. Do not use attachments not recommended by
Philips Electronics North America Corporation.
3. Never operate this shaver/charging stand if it has a damaged
cord or charging plug, if it is not working properly, if it has
been dropped or damaged, or dropped into water while
plugged in. For assistance call 1-800-243-3050.
ENGLISHENGLISH 54

7
Table of Contents
Features........................................................ 8-9
LED Multi-Purpose Display .......................10
Before First Use ...........................................11
Charging ...................................................11-13
Recharging .....................................................14
Quick Charge ...............................................14
Put It To The Test & Shaving Tips........14-15
How to Shave
With An Electric Shaver.......................15-17
Trimming ..................................................17-18
Cleaning....................................................18-23
Replacing the Shaving Heads...............23-25
Storage......................................................25-26
Assistance ......................................................26
Disposal..........................................................27
Accessories ...................................................28
Warranty........................................................29
ENGLISHENGLISH
6
45 - DAY MONEY-BACK GUARANTEE
To enjoy the closest and most comfortable shave from your new Philips Norelco
Men’s Shaver, the shaver should be used exclusively for 3 weeks.This allows your
hair and skin enough time to adapt to the Philips Norelco Shaving System. If, after
that period of time, you are not fully satisfied with your Philips Norelco Men’s
Shaver, send the product back along with dated sales receipt and we’ll refund
you the full purchase price. The shaver must be shipped prepaid by insured
mail, insurance prepaid, have the original sales receipt, indicating pur-
chase price, the date of purchase, and the money-back guarantee return
authorization form enclosed.We cannot be responsible for lost mail.
The shaver must be postmarked no later than 45 days from the date of purchase.
Philips Norelco reserves the right to verify the purchase price of the shaver and
limit refunds not to exceed suggested retail price.
To obtain money-back guarantee return authorization form,
call 1-800-243-3050 for assistance. Delivery of refund check will
occur 6–8 weeks AFTER receipt of refund product.

98 ENGLISH ENGLISH
How the Unique Philips Norelco Lift and Cut
Shaving System Makes Close Comfortable:
Groove channels
beard closer to
cutting system
Lifter raises hair Slots to cut long
hairs Holes to cut short
hairs even closer
Pop-up Trimmer
Automatic
Worldwide Voltage
100V to 240V AC
Cleaning Brush
Travel Pouch
(AT815/AT814)
Charging Stand
(AT815/AT814)
Rechargeable -
1-hour Full Charge
for up to 50 minutes
cordless use
Cordless - To shave
without a cord
Full 2-Year Warranty
45-Day Money-Back
Guarantee
Features
Lift and Cut System
Shaver Head
Assembly
Protective Cap
Individually
Floating
Heads
Shaver Head
Release Button
• Hair Chamber
captures shaven
hair
Electronic
On/Off Button
Shaver Head
Replacement Indicator
LED Charge
Indicators
•Battery Charge, Full,
Low & Quick Charge
Indicators

1110 ENGLISH
LED Multi-Purpose Display
The display provides the following information:
◗Charging Indicator
C-When the shaver is charging, the charging light
blinks green.
◗Full Charge Indicator
C-When the battery is fully charged, the charging
light lights up green continuously. After
approximately 30 minutes the charging light goes
off to save energy.
◗Low Battery Indicator
C -When the battery is almost empty (5 or less
shaving minutes left), the charging light blinks
orange.When you turn the shaver OFF the
charging light continues to blink orange for a few
seconds.
◗Quick Charge Indicator
-When you charge the empty battery, the
charging light alternately blinks orange and green.
After approximately 3 minutes, the charging light
continues to blink green.
- The shaver now contains enough energy for a
5-minute shave.
C◗Shaver Head Replacement Indicator
-Once a year, depending on your shaving behavior,
the shaver head replacement symbol will light up
orange continuously, as a reminder to replace the
shaving heads.
ENGLISH
Before First Use
◗ Charge the shaver before you start using
it (see ‘Charging’). Make sure the shaver is
switched off before you start charging it.
Important
◗ Only use the power cord provided to charge
the shaver.
◗ The power plug transforms 100-240V AC to
less than 24V DC.
Charging
◗ Charging or recharging at temperatures
below 40ºF/4,5ºC or higher than 95ºF/35ºC
adversely affects lifetime of batteries.
◗ If the shaver is subjected to a major change
in temperature, pressure or humidity, let it
acclimatize for 30 minutes before using.
◗Charging or recharging requires one full hour.
◗ A fully charged shaver has a cordless shaving
time of up to 50 minutes.
◗When charging shaver for the first time or
after a long period of non-use, charge until
the charging light lights up green continuously.
◗ Do not charge shaver in a pouch.

1312 ENGLISH
Charging with a Cord
C1Connect cord directly to shaver and
connect the charging plug into any 100V to
240V AC outlet. Use only the power cord
provided.
◗ An adaptor plug may be necessary for
charging plug usage in some foreign countries.
Use an attachment plug adaptor of the proper
configuration for the power outlet.
The charging plug will automatically convert to
work on 100V to 240V AC systems.
C ◗ The display on the shaver will indicate shaver
is charging.
2Charging and recharging requires a full 1
hour. A fully charged shaver has a cordless
shaving time of up to 50 minutes.
C ◗When the battery is fully charged, the
charging light lights up continuously.
After approximately 30 minutes, the charging light
goes out to save energy.
ENGLISH
Charging in Charging Stand
(AT815/AT814)
C ◗Always place shaver in stand in an upright
position making sure charging contacts in
bottom of stand fit into recess in bottom of
shaver.
◗Always remove shaver from stand by lifting
straight up. Do not tilt shaver.
1Place shaver in charging stand and connect
the small plug of cord to charging stand.
Connect the charging plug into any 100V
to 240V AC outlet. Use only the power
cord provided.
◗ An adaptor plug may be necessary for
charging plug usage in some foreign countries.
Use an attachment plug adaptor of the proper
configuration for the power outlet.
The charging plug will automatically convert to
work on 100V to 240V AC systems.
C ◗ The display on the shaver will indicate shaver
is charging.
2Charging and recharging requires one full
hour. A fully charged shaver has a cordless
shaving time of up to 50 minutes.
C◗When the battery is fully charged, the
charging light lights up continuously.
After approximately 30 minutes, the battery
symbol goes out to save energy.

1514 ENGLISH
Recharging
1Recharging requires 1 hour.
Recharge when the charging light on the shaver
display blinks orange.
Quick Charge
When you charge the empty battery, the charging
light alternately blinks orange and green. After
approximately 3 minutes, the charging light
continues to blink green.The shaver now contains
enough energy for a 5-minute shave.
Put It To The Test & Shaving Tips
◗21 Day Trial and Conversion Process.It is a fact
that your skin and beard need time to adjust to
a new shaving system.
◗Use your new shaver exclusively for 3 weeks
to fully enjoy the closeness of a Philips Norelco
shave.
◗At first you may not get as close a shave as you
expect,or your face may even become slightly
irritated.This is normal since your beard and
skin will need time to adjust.Invest 3 weeks and
you’ll soon experience the full joy of your new
shaver.
◗Stick with it! If you alternate shaving methods
during the adjustment period,it may make it
more difficult to adapt to the Philips Norelco
shaving system.
ENGLISH
◗If you are still not convinced after 21 days,
Philips Norelco will refund you the full
purchase price as long as the request is
received within 45 days of purchase.
HowTo Shave With An Electric Shaver
C◗This symbol on the shaver indicates that
the shaver can be used in both the bath and
shower.
◗The shaver will not operate while power cord
is connected to an electrical outlet.
◗ For hygienic reasons, the shaver should only
be used by one person.
◗Use this shaver for its intended household use
as described in this manual.
◗Shaving with a clean face gives the best results.
Shaving
C1Turn shaver ON by pressing the on/off
button once. Shave against the direction of
beard growth using circular movements.
2Stretch your skin with your free hand so
blades can lift and cut whiskers. Gently
press shaver to skin so the floating heads
can follow the contours of your face.
DO NOT press too hard.Too much
pressure can pinch the skin into the combs.

1716
C5Move the shaving heads in circular
movements over your skin.
NOTE: Rinse the shaver under the tap regularly
to ensure that it continues to glide smoothly over
your skin.
6Turn shaver OFF, dry your face and
thoroughly clean the shaver after each use
(see chapter ‘Cleaning’).
NOTE: Make sure you rinse all foam or gel off the
shaver.
C7When shaver is thoroughly dry, put the
Protective Cap on the shaver to protect
heads.
Trimming
To groom sideburns and moustache:
1Turn shaver ON.
C2Push down spring-release trimmer switch.
The trimmer can be activated while the shaver is
running.
ENGLISH
3Turn shaver OFF by pressing the on/off
button once.
4Clean the shaver after each use (see
chapter ‘Cleaning’).
C5Put the Protective Cap on the shaver to
protect shaver heads.
Wet Shaving
You can also use the shaver on a wet face with
shaving foam or gel.
C1Apply some water to your skin.
C2Apply shaving foam or gel to your skin.
3Rinse the shaving unit under the tap
to ensure that the shaving unit glides
smoothly over your skin.
4Press the on/off button once to switch on
the shaver.
ENGLISH

ENGLISH
C 3Hold trimmer as shown and move in
downward strokes with gentle pressure.
C4Close trimmer by pressing trimmer down.
5Turn shaver OFF.
Cleaning
◗Always clean your shaver after each use.
◗Always switch shaver OFF, unplug and remove
power cord before cleaning.
◗Never clean, remove or replace head
assembly while motor is on.
◗Do not apply pressure to combs. Do not
touch shaving heads with hard objects as this
may dent or damage precision-made slotted
combs.
◗Do not use shaver if combs are damaged or
broken. Facial injury may occur.
◗Do not use compressed air, abrasives,
scourers or aggressive liquids such as gasoline
or acetone to clean the shaver.
18 ENGLISH
Cleaning the Shaving Unit
The shaving heads may be quickly cleaned after
each use by rinsing with hot water: Water from
the tap should be on a hot setting, BUT BE
CAREFUL TO TEST WATER FIRST SO AS NOT
TO BURN OR SCALD HANDS.
◗Regular cleaning guarantees better shaving
results.
◗Do not immerse shaver in water.
◗While rinsing shaving heads, water may drip
out of the base of shaver.This is a normal
occurrence.
1Always turn shaver OFF, unplug from
outlet and remove power cord from
shaver.
C 2Press the Shaver Head Release Button to
open the Shaver Head Assembly.
C3Clean inside shaving heads and hair
chamber by running under hot water.
19

C 4Clean outside of Shaver Head Assembly by
running under hot water.
5Close the Shaver Head Assembly and
shake off excess water.
Be careful not to hit the shaving unit against
anything while shaking off excess water.
6Open Shaver Head Assembly again and
leave open to air dry.
NOTE: Do not wipe or dry the shaving heads
with a towel or tissue.This could damage the
shaving heads.
◗If you used foam or gel to shave, make sure to
rinse all of it off to prevent residue build-up
from clogging shaving heads.
◗If the shaving unit becomes detached from the
shaver, you can easily reattach it.
◗You may also clean the hair chamber without
water by using the supplied brush.
Extra-thorough Cleaning Method
Do not mix up the cutters and combs as the
shaving performance may be adversely affected
for several weeks before optimal shaving
performance is restored.
1Turn shaver OFF, remove the charging plug
from the outlet and power cord from the
shaver.
ENGLISH
20 ENGLISH
C2Press the Shaver Head Release Button to
open the Shaver Head Assembly.
C3Pull the shaving unit off the shaver.
C4Turn the lock counterclockwise to unlock
(A) and remove the retaining frame (B).
C 5Remove and clean one set of cutters and
combs at a time.
C 6Separate the cutter from the comb and
clean it with the short bristled side of the
brush supplied.
Do not clean more than one cutter and comb
at a time, since they are all matching sets. If you
accidentally interchange the cutters and combs, it
could take several weeks before optimal shaving
performance is restored.
21
A
B

ENGLISH
C 7Clean the inside and outside of the comb
with the brush supplied.
For optimum performance, shaver cutters and
combs should be cleaned in a degreasing liquid
(e.g. alcohol) and lubricated with one drop of
mineral oil (in the center of the head). This helps
prevent wear of the shaving heads.
C 8Replace the set back into the Shaver Head
Assembly.
Make sure that the two pointy edges of the
head fit exactly into the recesses.
9 Repeat the process for the other two sets
of cutters and combs.
10 Replace the frame and turn the lock
clockwise until it locks into place.
C 11 Insert the notch of the shaving unit into
the slot in the top of the shaver (1) and
then close the shaving unit (2).
NOTE: If the shaving unit does not close smoothly,
make sure you inserted the shaving heads
properly and that the retaining frame is locked.
12 Put the Protective Cap on shaver to
protect heads.
22 ENGLISH
After Each Use:Trimmer
1Turn shaver OFF.
C2Push down spring-release trimmer switch.
C3Clean trimmer with the short-bristled side
of the brush every time you use it. Brush
up and down along the trimmer teeth.
C4Lubricate the trimmer teeth with one
drop of mineral oil every 6 months.
5Close trimmer by pressing trimmer down.
Replacing the Shaving Heads
◗ Replace the shaving heads once a year for
optimal shaving results.
◗Replace damaged or worn shaver heads with
model HQ8 Philips Norelco shaving heads
only.
23
1
2

ENGLISH
Shaver Head Replacement Indicator
C◗The shaver head replacement indicator
symbol will light up orange continuously to
remind you to replace your shaving heads.
1Turn shaver OFF, remove the charging plug
from the outlet and power cord from the
shaver.
C2Press the Shaver Head Release Button to
open the Shaver Head Assembly.
C3Pull the shaving unit off the shaver.
C4Turn the lock counterclockwise to unlock
(A) and remove the retaining frame (B).
C 5Remove the shaving heads and place the
new shaving heads in the shaving unit.
Make sure that the two pointy edges of the head
fit exactly into the recesses.
24 ENGLISH 25
6Replace the frame and turn the lock
clockwise until it locks into place.
C 7Insert the notch of the shaving unit into
the slot in the top of the shaver (1) and
then close the shaving unit (2).
C 8Press and hold the on/off button for at
least 5 seconds to reset.The orange shaver
head replacement indicator symbol will go
out.
NOTE: If the shaving unit does not close smoothly,
make sure you inserted the shaving heads
properly and that the retaining frame is locked.
This shaver has no other user-serviceable parts.
For assistance call 1-800-243-3050.
Storage
◗Be sure shaver is turned off. Remove cord
from outlet and shaver before storing in a
safe, dry location where it will not be crushed,
banged, or subject to damage.
◗Do not wrap power cord around shaver when
storing.
◗Store cord in a safe location where it will not
be cut or damaged.
1
2
5 sec.5 sec.
A
B

ENGLISH
◗Do not place or store shaver where it can fall
or be pulled into a tub or sink, water or other
liquid while plugged in.
C◗Put the Protective Cap on shaver to protect
heads.
Assistance
◗ For assistance, visit our website:
www.philips.com/support or
call toll free 1-800-243-3050
◗ Online information is available 24 hours a day,
7 days a week.
26 ENGLISH
Disposal
C◗This Philips Norelco shaver contains a
rechargeable lithium-ion battery
which must be disposed of properly.
◗Contact your local town or city officials
for battery disposal information or call
1-800-822-8837 or www.rbrc.com for
battery drop-off locations.
◗For assistance, visit our website,
www.philips.com/support or call toll free:
1-800-243-3050.
27

ENGLISHENGLISH
Accessories
C ◗Replacement Heads
Model HQ8 - For maximum shaver
performance, replace your Philips Norelco
shaving heads once a year.
◗Philips Norelco Shaver Accessories may be
purchased at a store near you, or on our
website www.philips.com/store
2928
FULL TWO YEAR WARRANTY
Philips Electronics North America Corporation warrants each new Philips Norelco Product,
Model AT815/AT814/AT810 (except cutters and combs) against defects in materials or work-
manship for a period of two years from the date of purchase, and agrees to repair or replace
any defective product without charge.
IMPORTANT: This warranty does not cover damage resulting from accident, misuse or abuse,
lack of reasonable care, the affixing of any attachment not provided with the product or loss of
parts or subjecting the product to any but the specified voltage.*
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply go to www.philips.com/norelco or call 1-800-243-
3050 for assistance. It is suggested that for your protection you return shipments of product
by insured mail, insurance prepaid. Damage occurring during shipment is not covered by this
warranty.
NOTE: No other warranty, written or oral, is authorized by Philips Electronics North America
Corporation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state. Some states do not allow the exclusion or limitation of incidental or consequen-
tial damages, so the above exclusion and limitations may not apply to you.
* Read enclosed instructions carefully.
Manufactured for:
Philips Consumer Lifestyle
A division of Philips Electronics North America Corporation
P.O.Box 10313, Stamford, CT 06904
This symbol on the product’s nameplate means it is
listed by Underwriters’ Laboratories, Inc.
Norelco,Tripleheader, Lift and Cut, and are registered trademarks of Philips Electronics
North America Corporation.
is a trademark of Philips Electronics North America Corporation.
PHILIPS is a registered trademark of Koninklijke Philips N.V.
© 2016 Philips Electronics North America Corporation. All Rights Reserved.
4222 002 5418 3