Philips S7882 User manual

S7882

3
1
2
4
5
6
7
9
10 11 12
8

empty page before TOC

English 6
Français (Canada) 31

English
6English
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that Philips
offers, register your product at
www.philips.com/welcome or via the app.
General description
1 Pop-up trimmer
2 Trimmer release slide
3 Shaving unit
4 Shaving unit release button
5 On/off button
6 Handle
7 Socket for small plug
8 USB cable
Note: A suitable supply unit (e.g. Philips HQ87) is
available via www.philips.com/support.
9 Pouch
10 Quick Clean Pod Cartridge
11 Quick Clean Pod
12 Cleaning brush
Note: The accessories supplied may vary for different
products. The box shows the accessories that have been
supplied with your appliance.
Important safety information
Only use the product for its intended purpose. Read this
important information carefully before you use the
product and its batteries and accessories, and save it for
future reference. Misuse can lead to hazards or serious
injuries. Accessories supplied may vary for different
products.
The box shows which accessories are supplied with your
product and whether your product is Bluetooth enabled.

7
English
Warning
- To charge the product, only use a certified safety extra
low voltage (SELV) supply unit with output rating 5 V,
≥ 1 A. For safe charging in a moist environment (e.g.
in a bathroom), only use an IPX4 (splash-proof) supply
unit. A suitable supply unit (e.g. Philips HQ87) is
available via www.philips.com/support. If you need
support finding the correct USB supply unit, contact
Philips support at [phone]. Using a non-
certified supply unit may cause hazards or serious
injuries.
- Keep the USB cable and the USB supply unit dry.
- This shaver is waterproof. It is suitable for use in the
bath or shower and for cleaning under the tap. For
safety reasons, the shaver can therefore only be used
without cord.
- Do not modify the supply unit.
- This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children
shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without
supervision.
- Unplug the appliance before cleaning it with water.
- Do not use a damaged appliance. Replace damaged
parts with new Philips parts.
- Only use cold or lukewarm water to clean the
appliance.
- Because of hygiene, only one person should use the
appliance.

8English
- Never use compressed air, scouring pads, abrasive
cleaning agents or aggressive liquids to clean the
appliance.
- Always place the cleaning system on a stable, level
and horizontal surface to prevent leakage.
- Always make sure the cartridge compartment is
closed before you use the cleaning system.
- When the cleaning system is ready for use, do not
move it to prevent leakage of cleaning fluid.
- Water may drip from the socket at the bottom of the
shaver when you rinse it. This is normal and not
dangerous because all electronics are enclosed in a
sealed power unit inside the shaver.
- Do not use the supply unit in or near wall sockets that
contain an electric air freshener to prevent irreparable
damage to the supply unit.
- Be careful when handling your smartphone near
water and in moist environments.
- Radio waves may impair the operation of pacemakers
and other medical devices. Consult your phycisian for
advice and keep the appliance at least 20cm away.
- Only use original Philips accessories or consumables.
- Charge, use and store the product at a temperature
between 5°C and 35°C.
- Keep product and batteries away from fire and do not
expose them to direct sunlight or high temperatures.
- If the product becomes abnormally hot or smelly,
changes color or if charging takes longer than usual,
stop using and charging the product and contact
Philips.
- Do not place products and their batteries in
microwave ovens or on induction cookers.
- Do not open, modify, pierce, damage or dismantle the
product or battery to prevent batteries from heating
up or releasing toxic or hazardous substances. Do not
short-circuit, overcharge or reverse charge batteries.
- If batteries are damaged or leaking, avoid contact
with the skin or eyes. If this occurs, immediately rinse
well with water and seek medical care.

9
English

Philips Quick Clean Pod Cartridge fluid
- Keep out of reach of children.
- Do not swallow.
Electromagnetic fields (EMF)
This Philips appliance complies with all applicable
standards and regulations regarding exposure to
electromagnetic fields.
Radio Equipment Directive
- S7000 series appliances are equipped with Bluetooth
class 2.
- The frequency band in which the Bluetooth on S7000
series appliances operates is 2.4GHz.
- The maximum radio frequency power radiated in the
frequency band in which the S7000 series appliances
operate is less than 20 dBm.
- This equipment has been so constructed that the
product complies with the requirement of Article
10(2) as it can be operated in at least one EU Member
State as examined and the product is compliant with
Article 10(10) as it has no restrictions on putting into
service in all EU member states.
- Hereby Philips declares that S7000 series appliances
are in compliance with the essential requirements and
other relevant provisions of Directive 2014/53/EU.
The declaration of conformity may be consulted at
www.philips.com/support.
General
- Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
- This device complies with ISED license-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.

10 English
- This device complies with the ISED RF exposure limits
and has been evaluated in compliance with portable
exposure condition.
- There is no limitation as to which distance can be used
from the human body.
- This Class B digital apparatus complies with Canadian
ICES-003.
What do the icons on my appliance handle mean?
Icon Behavior Meaning
Pulsing The cleaning program is in progress.
Flashing slowly
when you remove
the shaver from the
Quick Clean Pod
during the cleaning
program
The cleaning program was interrupted. If you
put the shaver back into the Quick Clean Pod
within four seconds, the cleaning program
resumes automatically.
Flashing when you
switch off the
appliance
Clean the shaver in the Quick Clean Pod (see
'How do I use the Quick Clean Pod?'). Clean the
attachments under the tap.
Lights up
continuously The cleaning program is in progress.
Flashing quickly
when you remove
the shaver from the
Quick Clean Pod or
press the on/off
button during the
cleaning program
The cleaning program was stopped. If you wish
to continue, you need to restart the cleaning
cycle by putting the shaver into the Quick Clean
Pod and pressing the on/off button.
Lights up The SkinIQ is actively detecting your shaving
behavior.
Lights up green The correct shaving motion (circular
movements) was used.

11
English
Icon Behavior Meaning
Lights up orange Your shaving motion can be improved. See the
app for details and advice.
Lights up Open the app. Either there is a notification
waiting for you or you need to sync your shaves
to prevent data loss (see 'How do I connect my
shaver and smartphone? (Fig. A)').
Flashing slowly No connection is established between your
shaver and smartphone (see 'How do I connect
my shaver and smartphone? (Fig. A)').
Flashing quickly An error has occurred (e.g. the motor is
blocked). Check the app for details.
Flashing The appliance must be disconnected from the
wall socket before you can switch it on (see
'How do I charge my appliance?').
Flashing when you
press the on/off
button
The travel lock is activated (see 'Storage and
travel').
Lights up when you
pick up the
appliance
The number of bars lit up show the remaining
battery charge.
Bottom light
flashing orange The battery is almost empty (see 'How do I charge my appliance?').
Lights flashing in
sequence The appliance is charging.
Lights up
continuously The appliance is fully charged.

12 English

What does the icon on my Quick Clean Pod mean?
Icon Behavior Meaning
Becomes visible on the Quick
Clean Pod The Quick Clean Pod Cartridge needs to be replaced (see 'How do
I use the Quick Clean Pod?').
How do I charge my appliance?
Charge the appliance before you use it for the first time
and when the bottom light of the battery status indicator
flashes orange, indicating that the battery is almost
empty.
Charging takes approx. 1 hour.
Quick Charge: After approx. 5 minutes of charging, the
battery contains enough energy for one full shave.
When the appliance is fully charged it has a cordless
operating time of up to 60 minutes.
Note: You cannot use the appliance while it is charging.
Charging with the supply unit
Warning: Keep the USB cable and the USB supply
unit dry.
1Make sure that the appliance is switched off.
2Insert the small plug of the USB cable into the socket
in the bottom of the appliance.
3Insert the USB plug into the USB supply unit (not
provided).

13
English
4Insert the USB supply unit into the wall socket.
- While the appliance is in quick charge mode, the
lights of the battery status indicator light up one
after the other. After approximately 5 minutes, the
bottom light of the battery status indicator flashes.
The battery now contains enough energy for one
full shave.
- While the appliance charges, first the bottom light
of the battery status indicator flashes and then
lights up continuously. Next the second light
flashes and then lights up continuously, and so on
until the appliance is fully charged.
- When the appliance is fully charged, all three
battery indicator lights light up continuously. After
approx. 30 minutes, the light goes out
automatically.
5After charging, remove the USB supply unit from the
wall socket, pull the USB plug out of the supply unit
and then pull the small plug out of the appliance.
'Unplug for use' symbol
The 'unplug for use' symbol flashes to remind you to
disconnect the appliance from the wall socket and
remove the small plug from the appliance before you
switch it on.
How do I use my appliance?
Warning: Always check the appliance and all
accessories before use. Do not use the appliance
or any accessory if it is damaged, as this may cause
injury. Always replace a damaged part with one of
the original type.
Note: This appliance is waterproof. It is suitable for use in
the bath or shower and for cleaning under the tap. For
safety reasons, the appliance can therefore only be used
without cord.

14 English
SkinIQ
This appliance is equipped with SkinIQ technology which
intelligently detects your hair density and shaving
technique. For a better technique, you can get
personalized shaving advice in the app.
You get advice in 2 ways: guided shaves in real time and
synchronized shaves. We advise you to start with the
guided shave to enhance your shaving experience.
- Correct handling of your appliance will contribute to
the best shaving result.
- Follow the advice obtained from the synchronized
shaves and the personalized programs.
Shaving
You can use this appliance either wet or dry, or even
under the shower. For a wet shave, apply some water and
shaving foam or gel to your skin and rinse the shaving
heads under the tap with warm water before following
the steps below.
1Switch on the appliance.
2Move the shaving heads over your skin in circular
movements to catch all hairs growing in different
directions. Make sure each shaving head is fully in
contact with the skin. Exert gentle pressure for a close,
comfortable shave.
Note: Do not press too hard, as this can cause skin
irritation.
Note: If you are shaving with gel or foam, rinse the
shaving unit regularly during your shave to ensure
that it continues to glide smoothly over your skin.

15
English
3Use the narrow sides of the shaving unit to shave in
hard-to-reach areas such as along your jawline and
under your nose.
4Switch off and clean the appliance after each use.
Note: Make sure you rinse all foam or shaving gel off
the appliance.
SkinIQ motion guidance: When you have finished
shaving you receive feedback on the handle. The
motion feedback icon lights up in various colors,
giving you feedback on your overall shave.
- When you shave in the correct motion (circular
movements), the motion feedback icon lights up
green.
- When your shaving motion can be improved, the
motion feedback icon lights up orange. See the
app for details and advice.
Skin adaptation period
Your first shaves may not bring you the result you expect
and your skin may even become slightly irritated. This is
normal. Your skin needs time to adapt to any new
shaving system.
Follow the advice provided by the app and shave
regularly (at least 3 times a week) with this shaver for a
period of 3-4 weeks to allow your skin to adapt to the
new shaver.
Cleaning reminder
When you switch off the appliance, the cleaning
reminder flashes to remind you to clean the appliance.
- Clean the appliance and attachments after each use
to prevent clogging and damage.
- Clean the shaving heads thoroughly once a month or
when the appliance does not shave as well as it used
to (see 'Thorough cleaning').
Synchronize your shaves
This shaver stores your shave data so you don't need to
take your smartphone with you when you shave.

16 English
When the data storage is almost full, the notification
symbol flashes. To prevent data loss, synchronize the
shaver with the app (see 'How do I connect my shaver
and smartphone? (Fig. A)').
1Make sure you are close to the shaver and open the
app.
2The app connects automatically and synchronizes
your last shaves.
Trimming
You can use the trimmer to groom your sideburns and
moustache.
1Push the trimmer release slide downwards to open
the trimmer.
2Switch on the appliance.
3Hold the trimmer perpendicular to the skin and move
the appliance downwards while you exert gentle
pressure.
4You can also use the trimmer under your nose.
5Switch off the appliance and clean the trimmer after
each use to prevent clogging and damage.
6Close the trimmer.
Storage and travel
Note: We advise you to let the appliance and its
attachments dry before you store them for the next use.
- Store the appliance in the pouch (if supplied).
Travel lock
You can lock the shaver when you are going to travel to
prevent it from switching on accidentally.

17
English
Activating the travel lock
3 sec.
Press the on/off button for 3 seconds to use the travel
lock mode.
When the travel lock is activated, the travel lock symbol
flashes.
Note: Bluetooth is switched off when the travel lock is
activated.
Deactivating the travel lock
Press the on/off button for 3 seconds.
Once the travel lock is deactivated, the appliance
switches on automatically.
Note: The shaver unlocks automatically when it is
connected to a wall socket.
How do I clean my appliance?
Clean the appliance and the attachments after each use
for optimal performance.
Cleaning the shaver under the tap
Clean the shaver after each use to prevent clogging and
damage.
Never dry the shaving unit with a towel or tissue, as
this may damage the shaving heads.
While rinsing the shaving unit, water may drip out of
the base of the shaver. This is a normal occurrence.
1Switch on the shaver.
2Rinse the shaving unit under a warm tap.
3Switch off the shaver. Press the release button to
open the shaving unit.

18 English
4Rinse the hair chamber under a warm tap.
5Rinse the shaving head holder under a warm tap.
6Carefully shake off excess water and let the shaving
head holder air-dry completely.
7Close the shaving unit.
Thorough cleaning
We advise you to clean the shaving heads thoroughly
once a month or when the shaver does not shave as well
as it used to.
1Make sure that the appliance is switched off and
disconnected from the wall socket.
2Press the release button on the shaving unit and pull
the shaving head holder off the shaving unit.
3Rinse the hair chamber and shaving head holder
under the tap.
4Remove the shaving heads. For detailed instructions,
see 'How do I replace the shaving heads?'.
Note: Do not clean more than one cutter and guard at
a time, since they are all matching sets. If you
accidentally put a cutter in the wrong shaving guard,

19
English
it may take several weeks before optimal shaving
performance is restored.
5Clean the cutter and guard under the tap.
6Shake off excess water.
7Put the shaving heads back into the shaving unit. For
detailed instructions, see 'How do I replace the
shaving heads?'.
8Insert the hinge of the shaving head holder into the
slot in the top of the shaving unit and close the
shaving unit.
Cleaning the pop-up trimmer
Clean the trimmer after each use to prevent clogging and
damage.
Never dry the trimmer teeth with a towel or tissue, as
this may damage the trimmer teeth.
1Make sure that the appliance is switched off and
disconnected from the wall socket.
2Push the trimmer release slide down to open the pop-
up trimmer.
3Switch on the appliance and rinse the pop-up trimmer
with warm water.
4After cleaning, switch off the appliance.
5Carefully shake off excess water and let the pop-up
trimmer air dry.
6Close the trimmer.

20 English
Tip: For optimal performance, lubricate the teeth of the
pop-up trimmer with a drop of mineral oil every six
months (oil not included).
How do I use the Quick Clean Pod?
Preparing the Quick Clean Pod for use
1Twist and remove the top of the Quick Clean Pod.
2
1
2Twist the lid off of the Quick Clean Pod Cartridge.
3Lift the tab on the seal and pull it by the corner to
remove the seal from the Quick Clean Pod Cartridge.
4Press the small circular piece on the handle of the
Quick Clean Pod Cartridge to break the snap hook on
the handle.