Philips QT4015 User manual

Always here to help you
Register your product and get support at
www.philips.com/welcome
User manual
QT4015

1

QT4015
ENGLISH 4
 11
 18
EESTI 25
 32
 39
 46
 53
 60
 67
 74
 81
 88
 95
 102
 109

4
Introduction
Congratulations on your purchase and welcome to Philips!To fully

www.philips.com/welcome.
General description (Fig. 1)
1 Trimming comb
2 Cutting unit
3 Precision Zoom Lock™ adjustment ring
4 On/off slide with battery indicator
5 Socket for appliance plug
6 Pouch
7 Brush
8 Appliance plug
9 Adapter
Important
Read this user manual carefully before you use the appliance and save it for
future reference.
Danger
- Make sure the adapter does not get wet.
Warning
- The adapter contains a transformer. Do not cut off the adapter to

- This appliance is not intended for use by persons (including children) with


concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the
appliance.
Caution
- Never immerse the appliance in water or rinse it under the tap.
Only the cutting unit can be rinsed under the tap.
- 

- Only use the adapter supplied.
- 

- This appliance is only intended for trimming the human beard. Do not
use it for any other purpose.
- Do not use the appliance if the cutting unit or the trimming comb is


This Philips appliance complies with all standards regarding electromagnetic


available today.
ENGLISH

General
- The appliance is equipped with an automatic voltage selector and is
suitable for mains voltages from 100 to 240 volts.
- The adapter transforms 100-240 volts to a safe low voltage of less than
24 volts.
Charging



to 60 minutes.
Note:You can use the appliance cordless as well as connected to the mains.
1 Make sure the appliance is switched off.
2 Insert the appliance plug into the appliance.
3 Put the adapter in the wall socket.
,
is charging.
,When the battery is fully charged, the charging light lights up green
continuously.After 30 minutes, the charging light goes out.
4 After charging, remove the adapter from the wall socket and pull the
appliance plug out of the appliance.
Battery low
When the battery is almost empty (when there are only 5 or fewer

Optimising the lifetime of the rechargeable battery

use it until the battery is completely empty. Continue to use the appliance
until the motor almost stops running during a session.Then recharge the

Using the appliance

start trimming.

too fast. Make smooth and gentle movements.
ENGLISH 5

Trimming with comb
1 Turn the Precision Zoom Lock™adjustment ring to the
desired setting.The selected setting is the setting in the centre of the
adjustment ring.
See the table below for an overview of the settings and the resulting hair
lengths.
Setting Resulting hair length Setting Resulting hair length
. 0.5mm . 5.5mm
1 1mm 6 6mm
. 1.5mm . 6.5mm
2 2mm 7 7mm
. 2.5mm . 7.5mm
3 3mm 8 8mm
. 3.5mm . 8.5mm
4 4mm 9 9mm
. 4.5mm . 9.5mm
5 5mm 10 10mm

familiarise yourself with the appliance.
2 Switch on the appliance.
3 To trim most effectively, move the trimmer against the hair growth
direction. Make sure the surface of the comb always stays in contact
with the skin.
4 If a lot of hair has accumulated in the beard trimming comb,
remove the comb and blow and/or shake the hair out of it.
The selected setting does not change when you do this.
3•4••1 2
ENGLISH6

Trimming at the unique ‘stubble look’ setting
1 To create a ‘stubble look’, trim with the beard trimming comb set
to setting 1.
Trimming without comb
Use the trimmer without beard trimming comb to trim full beards and
single hairs.
Be careful when you trim without comb because the cutting
element removes every hair it touches.
1 
2 Switch on the appliance.
3 Make well-controlled movements.Touch the hair lightly with the
trimmer.
Corded trimming

1 Switch off the appliance, insert the adapter in the wall socket and
wait a few seconds before you switch on the appliance.
Cleaning
Never use scouring pads, abrasive cleaning agents or aggressive liquids
such as alcohol, petrol or acetone to clean the appliance.
1 Make sure the appliance is switched off and disconnected from the
mains.
2 Wipe the housing of the appliance with a dry cloth.
Never immerse the appliance in water or rinse it under the tap.
3 Remove the trimming comb and clean it with the brush.
ENGLISH 7

4 Remove the cutting unit by pushing against the teeth of the cutting
unit and clean it with the brush or rinse it under the tap.
5 Shake off excess water and place the cutting unit back by inserting
the lug of the cutting unit into the guiding slot.
6 Push the cutting unit back onto the appliance (‘click’).
Replacement
Only replace a worn or damaged cutting unit with an original Philips cutting

1 Open the cutting unit.
2 Remove the old cutting unit by pushing against the teeth of the
cutting unit.
3 Insert the lug of the new cutting unit into the guiding slot.
4 Push the cutting unit back onto the appliance (‘click’).
ENGLISH8

Ordering accessories

www.shop.philips.com/service. If the online shop is not available in




Environment
- Do not throw away the appliance with the normal household waste


- The built-in rechargeable battery contains substances that may pollute
the environment.Always remove the battery before you discard and



service centre.The staff of this centre will remove the battery for you
and will dispose of it in an environmentally safe way.
Removing the rechargeable batteries
Only remove the rechargeable batteries if they are completely empty.
1 
until the motor stops.
2 Insert a screwdriver in the hair chamber to separate the housing
part.
3 Cut the wires close to the batteries with a pair of household
scissors.
ENGLISH 9

4 Remove the printed circuit board with the rechargeable batteries.
5 Cut the battery tabs with a pair of scissors and separate the
batteries from the printed circuit board.

Guarantee and service

the Philips website at www.philips.com/support or contact the Philips



ENGLISH10