Philips HTS7200 User manual

Register your product and get support at
www.philips.com/welcome
EN User manual
DE Benutzerhandbuch
ES Manual del usuario
FR Mode d’emploi
NL Gebruiksaanwijzing
HTS7200

2

3
7 Adjust settings 31
Video Setup 31
Audio Setup 32
Preference Setup 33
EasyLink Setup 34
Advanced Setup 35
8 Update software 37
Update software via network 37
Update software via USB 37
9 Specifications 38
10 Troubleshooting 39
11 Glossary 41
Contents
1 Important 4
Safety and important notice 4
Trademark notice 5
Care 6
2 Your product 7
Feature highlights 7
Product overview 8
3 Connect 11
Place the product 11
Connect video cables 11
Connect speaker cables to speakers 13
Connect speakers and subwoofer 13
Connect radio antenna 13
Connect audio cables/other devices 14
Connect LAN 16
Connect power cord 16
4 Get started 17
Insert the remote control batteries 17
Find the correct viewing channel 17
Use the Home menu 18
Select menu display language 18
Set up network 18
Use Philips EasyLink 19
5 Play 21
Play a disc 21
Play video 22
Play music 25
Play photo 26
Play from USB device 27
Play from portable media player 28
Play from radio 28
6 Adjust sound 30
Control the volume 30
Change treble and bass 30
Select surround sound 30
Select preset sound 30
English
EN

4
Copyright
This product incorporates copyright
protection technology that is protected
by method claims of certain U.S. patents
and other intellectual property rights
owned by Macrovision Corporation and
other rights owners. Use of this copyright
protection technology must be authorised
by Macrovision Corporation, and is intended
for home and other limited viewing uses only
unless otherwise authorised by Macrovision
Corporation. Reverse engineering or
disassembly is prohibited.
Copyright in the U.K.
Recording and playback of material may
require consent. See Copyright Act 1956 and
The Performers’ Protection Acts 1958 to
1972.
Mains fuse (UK only)
This product is fitted with an approved
moulded plug. Should it become necessary to
replace the mains fuse, this must be replaced
with a fuse of the same value as indicated on
the plug (example 10A).
1Remove fuse cover and fuse.
2The replacement fuse must comply with
BS 1362 and have the ASTA approval
mark. If the fuse is lost, contact your
dealer in order to verify the correct type.
3Refit the fuse cover.
Note
To conform to the EMC directive (2004/108/•
EC), the mains plug on this product must not
be detached from the mains cord.
1 Important
Safety and important notice
Warning
Risk of overheating! Never install the product•
in a confined space. Always leave a space
of at least 4 inches around the product for
ventilation. Ensure curtains or other objects
never cover the ventilation slots on the
product.
Never place the product, remote control or
•
batteries near naked flames or other heat
sources, including direct sunlight.
Only use this product indoors. Keep this
•
product away from water, moisture and liquid-
filled objects.
Never place this product on other electrical
•
equipment.
Keep away from this product during lightning
•
storms.
Where the mains plug or an appliance
•
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
Visible and invisible laser radiation when open.
•
Avoid exposure to beam.
This product is in compliance with the
essential requirements and other relevant
provisions of Directives 2006/95/EC (Low
Voltage) and 2004/108/EC (EMC).
EN

5
Trademark notice
HDMI, and HDMI logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI licensing LLC.
Windows Media and the Windows logo are
trademarks, or registered trademarks of
Microsoft Corporation in the United States
and/or other countries.
The USB-IF Logos are trademarks of Universal
Serial Bus Implementers Forum, inc.
DivX, DivX Ultra Certified, and associated
logos are trademarks of DivX, Inc. and are
used under license.
Official DivX® Ultra Certified product.
Plays all versions of DivX ® video (including
DivX ® 6) with enhanced playback of DivX®
media files and the DivX® Media Format.
Plays DivX® video with menus, subtitles and
audio tracks.
‘DVD Video’ is a trademark of DVD Format/
Logo Licensing Corporation.
‘Blu-ray Disc’ and the ‘Blu-ray Disc’ logo are
trademarks.
Disposal of your old product and
batteries
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When this crossed-out wheeled bin symbol
is attached to a product it means that the
product is covered by the European Directive
2002/96/EC. Please inform yourself about the
local separate collection system for electrical
and electronic products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste.
Correct disposal of your old product helps to
prevent potential negative consequences for
the environment and human health.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed with normal household
waste.
Please inform yourself about the local rules
on separate collection of batteries because
correct disposal helps to prevent negative
consequences for the environmental and
human health.
English
EN

6
ENERGY STAR and the ENERGY STAR mark
are registered U.S. trademarks.
Care
Caution
Never use solvents such as benzene, thinner,•
cleaners available commercially or anti-static
sprays intended for discs.
Clean discs
Wipe the disc with a micro fibre cleaning cloth
from the centre to the edge in a straight line
movement.
LASER RADIATION
DO NOT VIEW DIRECTLY
WITH OPTICAL INSTRUMENTS
CLASS 1M LASER PRODUCT
Manufactured under licence from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
Manufactured under licence under U.S. Patent
#s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,487,535; & other U.S. and worldwide
patents issued & pending. DTS is a registered
trademark and the DTS logos, Symbol, DTS-
HD and DTS-HD Advanced Digital Out are
trademarks of DTS, Inc. © 1996-2008 DTS,
Inc. All Rights Reserved.
Java and all other Java trademarks and logos
are trademarks or registered trademarks of
Sun Microsystems, Inc. in the United States
and/or other countries.
BONUSVIEW™
‘BD LIVE’ and ‘BONUSVIEW’ are trademarks
of the Blu-ray Disc Association.
‘AVCHD’ and the ‘AVCHD’ logo are
trademarks of Matsushita Electric Industrial
Co., Ltd and Sony Corporation.
‘x.v.Colour’ is a trademark of Sony
Corporation.
EN

7
BD-Live
Connect this product to the movie studios’
website via the LAN port to access a variety
of up-to-date content (e.g. refreshed previews
and exclusive special features). You can also
enjoy next generation possibilities, such as
ringtone/wallpaper downloads, peer-to-peer
interactions, live events and gaming activities.
Region codes
You can play discs with the following region
codes.
Region
code
Country
DVD BD
Europe,
United
Kingdom
Asia Pacific,
Taiwan, Korea
Latin America
Australia,
New Zealand,
Russia, India
China
B
A
A
B
C
C
2 Your product
Congratulations on your purchase, and
welcome to Philips! To fully benefit from the
support that Philips offers; register your product
at www.philips.com/welcome.
Feature highlights
Philips EasyLink
Your product supports Philips EasyLink, which
uses the HDMI CEC (Consumer Electronics
Control) protocol. EasyLink-compliant devices
that are connected through HDMI connectors
can be controlled by a single remote control.
Note
Philips does not guarantee 100%•
interoperability with all HDMI CEC devices.
High-Definition entertainment
Watch a high-definition content disc with
HDTV (High Definition Television). Connect
it through a high speed HDMI cable (1.3 or
category 2). You can enjoy excellent picture
quality up to 1080p resolution with the frame
rate of 24 frames per second with progressive
scan output.
BONUSVIEW/PIP (Picture-in-Picture)
This is a new function of BD-Video that
plays the primary video and secondary video
simultaneously. Blu-ray players with Final
Standard Profile or Profile 1.1 specs can play
Bonus View features.
English
EN

8
iDisc compartment
jMP3 LINK jack
Connect a portable audio player.
kUSB jack
Connect a USB supported device.
Remote control
a
b
d
c
|
e
f
g
h
k
l
m
n
o
p
q
r
s
t
i
j
u
v
w
x
y
z
{
Product overview
Main unit
a(Standby-On)
Turn on the Home Theatre System or
switch to standby mode.
bSOURCE
Select media to play or listen to audio
from the connected device.
cVOL +/-
Increase or decrease volume.
d(Stop)
Stop play.•
Press and hold to erase the preset•
radio station.
e(Play/Pause)
Start, pause or resume play.•
In radio mode, automatically tune•
radio stations during first-time setup.
f(Open/Close)
Open or close the disc compartment.
gDisplay panel
hIR sensor
Detect signals from the remote control.
Point the remote control directly at the
sensor.
ab
ijk
cdefg
h
EN

9
k(Pause)
Pause play.•
Move the paused picture one step•
forward.
l(Stop)
Stop play.•
Press and hold to erase the preset•
radio station.
m(Mute)
Mute or restore audio output.
nTREBLE / BASS
Change treble or bass. Use with +/-.
oSOUND MODE
Select a sound mode.
pNumeric buttons
Select an item or setting.
qSUBTITLE
Select a subtitle language for video.
rREPEAT /PROGRAM
Toggle between various repeat or•
shuffle modes.
In radio mode, press to start manual•
radio preset; press and hold to start
automatic radio preset.
sHDMI
Select the video resolution of HDMI
output from the home theatre.
tBONUS VIEW
Blu-ray discs only: Enable or disable the
Bonus View/Picture-In-Picture feature.
uAUDIO SYNC
Synchronise audio with video. Use with
+/-.
vAUDIO
In video mode, toggle between audio•
languages.
In radio mode, toggle between•
stereo and mono.
w+/- (Volume +/-)
Increase or decrease volume.
a(Standby-On)
Turn on the home theatre or switch•
it to standby mode.
When EasyLink is enabled, press•
and hold for at least three seconds
to turn all connected HDMI CEC-
compliant devices to standby.
bOPEN/CLOSE
Open or close the disc compartment.
cSource buttons
•DISC / POP-UP MENU: Switch to
disc source.Access to disc menu
during play.
•RADIO: Switch to FM radio.
•USB: Switch to the connected USB
device.
•AUDIO SOURCE: Select an audio
input.
Display Device connected to
AUX1 AUDIO IN-AUX1
AUX2 AUDIO IN-AUX2
COAX IN DIGITAL IN-COAXIAL
OPTI IN DIGITAL IN-OPTICAL
MP3 LINK MP3 LINK
dColour buttons
Blu-ray discs only: Select a task or option.
e(Home menu)
Access the home menu.
fOPTIONS
Access options for the current activity or
selection.
g(Navigation buttons)
Navigate menus.
hOK
Confirm an entry or selection.
iINFO
Display information about what is playing.
j(Play)
Start or resume play.
English
EN

10
xSURR. SOUND
Switch audio output to multi-channel•
surround or stereo mode.
For HTS7200 only: Switch audio•
output to DOLBY Virtual speaker or
Stereo mode.
y/ (Previous/Next)
In video mode, skip to previous or•
next title, chapter or track.
In radio mode, select a preset radio•
station.
z/ (Fast Backward / Fast Forward)
Fast reverse or fast forward. Press
repeatedly to change the search speed.
{BACK
Return to a previous menu screen.
|TOP MENU
Access the main menu of a video disc.
EN

11
1Place this Home Theatre System near to
the TV
2Place the speakers system at normal
listening ear-level and directly parallel to
the listening area.
3Place the subwoofer at the corner of the
room or at least 1 metre (3 feet) away
from the TV.
Tip
To avoid magnetic interference or unwanted•
noise, never place this home theatre too close
to any radiation devices.
Connect video cables
Connect this Home Theatre System to a TV to
view disc play. Select the best video connection
that the TV can support.
Option 1: Connect to the HDMI jack (for•
a HDMI, DVI or HDCP-compliant TV).
Option 2: Connect to the component•
video jacks (for a standard TV or
progressive scan TV).
Option 3: Connect to the video (CVBS)•
jack (for a standard TV).
Note
You must connect this Home Theatre System•
directly to a TV.
FRONT
RIGHT
FRONT
LEFT
SUBWOOFER
3 Connect
Make the following connections to use your
Home Theatre System. For a comprehensive
interactive guide, see www.connectivityguide.
philips.com.
Basic connections:
Video•
Speakers and subwoofer•
Power•
Optional connections:
Radio antenna•
Audio•
Audio from TV•
Audio from cable box/recorder/•
game console
Other devices•
Portable media player•
USB device•
LAN (Network)•
Note
Refer to the type plate at the back or bottom•
of the product for identification and supply
ratings.
Before you make or change any connections,
•
ensure that all devices are disconnected from
the socket.
Place the product
Place the product where it cannot be•
pushed, pulled over or knocked down.
Do not place it in an enclosed cabinet.
Make sure that you have full access to the•
power cord for easy disconnection of the
product from the power supply.
English
EN

12
Option 2: Connect to the component
video jack
1Connect the component video cable
(not supplied) to the Y Pb Pr jacks on
this Home Theatre System and the
COMPONENT VIDEO input jacks on the
TV.
Note
The component video input jack on the TV•
might be labelled as Y Pb Pr,Y Cb Cr or YUV.
This type of connection provides good picture
•
quality.
PbPr Y
PbPr Y
Option 1: Connect to the HDMI jack
1Connect the HDMI cable to the HDMI
OUT jack on this Home Theatre System
and the HDMI input jack on the TV.
Tip
If the TV has a DVI connector only, connect via•
a HDMI/DVI adapter. Connect an audio cable
for sound output.
You can optimise the video output. Press
•
HDMI repeatedly to select the best resolution
the TV can support.
To play back the digital video images of a BD-
•
video or DVD-video via an HDMI connection,
it is necessary that both the Home Theatre
System and the display device support a
copyright protection system called HDCP
(high-bandwidth digital content protection
system).
This type of connection provides the best
•
picture quality.
HDMI OUT
HDMI IN
EN

13
Connect speakers and
subwoofer
1Connect the speakers and subwoofer to
the matching jacks on this Home Theatre
System.
Note
Ensure that the colours of the plugs and jacks•
are matched.
Connect radio antenna
FM (75 Ω)
ANTENNA
Option 3: Connect to the Video
(CVBS) jack
1Connect a composite video cable (not
supplied) to the VIDEO jack on this
Home Theatre System and the VIDEO
input jack on the TV.
Note
The video input jack on the TV might be•
labelled as A/V IN,VIDEO IN,COMPOSITE
or BASEBAND.
This type of connection provides standard
•
picture quality.
Connect speaker cables to
speakers
1Match the colour of the cable to the
terminal tab.
2Press the terminal tab down and insert
the stripped end of the speaker cable,
then release.
VIDEO
VIDEO OUT
VIDEO IN
English
EN

14
Note
To listen to the audio output from this•
connection, press AUDIO SOURCE
repeatedly until ‘AUX1’ is displayed on the
display panel.
Connect audio from a cable box,
recorder or games console
You can choose to connect to analogue
or digital jacks depending on the device
capabilities.
Connect to analogue jacks
1Connect the audio cables (not supplied)
to the AUDIO IN-AUX2 jacks on this
Home Theatre System and the AUDIO
output jacks on the device.
AUDIO OUT
AUX 2
AUDIO IN
1Connect the FM antenna to the FM75
jack on this Home Theatre System
(for some models, this cable is already
connected).
2Extend the FM antenna and fix its ends to
the wall.
Tip
For better FM stereo reception, connect to an•
external FM antenna.
Connect audio cables/other
devices
Route the audio from other devices to this
Home Theatre System to enjoy audio play with
multi-channel surround capabilities.
Connect audio to TV
(also used for EasyLink control)
1Connect the audio cables (not supplied)
to the AUDIO IN-AUX1 jacks on this
Home Theatre System and the AUDIO
output jacks on the TV.
AUDIO OUT
AUX 1
AUDIO IN
EN

15
Connect to optical jack
1Connect an optical cable (not supplied)
to the DIGITAL-IN-OPTICAL jack
on this Home Theatre System and the
OPTICAL/SPDIF output jack on the
device.
Note
To listen to the audio output from this•
connection, press AUDIO SOURCE
repeatedly until ‘OPTI IN’ is displayed on the
display panel.
Connect portable media player
DIGITAL IN
OPTICAL
DIGITAL OUT
OPTICAL
MP3
Note
To listen to the audio output from this•
connection, press AUDIO SOURCE
repeatedly until ‘AUX2’ is displayed on the
display panel.
Connect to coaxial jack
1Connect a coaxial cable (not supplied)
to the DIGITAL-IN-COAXIAL jack
on this Home Theatre System and the
COAXIAL/DIGITAL output jack on the
device.
Note
To listen to the audio output from this•
connection, press AUDIO SOURCE
repeatedly until ‘COAX IN’ is displayed on the
display panel.
COAXIAL
DIGITAL OUT
COAXIAL
DIGITAL IN
English
EN

16
1Connect the network cable (not
supplied) to the LAN jack on this Home
Theatre System and the LAN jack on the
broadband modem or router.
Note
Use an RJ45 straight cable. Do not use a•
crossover cable.
Internet access to Philips website for software
•
updates may not be allowed, depending on
the router you use or the Internet Service
Provider’s policy. Contact your Internet
Service Provider for more information.
Connect power cord
Warning
Risk of product damage! Ensure that the•
power supply voltage corresponds to the
voltage printed on the back or the underside
of the product.
1Connect the power cord to the socket
when all the required connections are
made.
This product is ready to be set up for»
use.
LAN
BROADBAND
1Connect a 3.5 mm stereo audio cable
(not supplied) to the MP3 LINK jack
on this Home Theatre System and the
phone jack on the portable media player
(such as MP3 player).
Note
To listen to the audio output from this•
connection, press AUDIO SOURCE
repeatedly until ‘MP3 LINK’ is displayed on the
display panel.
Connect USB device
1Connect the USB device to USB jack
on this Home Theatre System.
Note
This Home Theatre System can only play/view•
MP3, WMA, DivX (Ultra) or JPEG files that are
stored on such devices.
Press
•USB to access the content and play the
files.
Connect LAN
Connect this Home Theatre System to the
network for software updates and enjoy BD-
Live applications.
EN

17
Navigate through the menu
1Point the remote control directly at the
remote sensor on the product and select
the desired function.
2Press the following buttons on the
remote control to navigate through the
on-screen menus.
Button Action
Move up or down
Move left or right
OK Confirm a selection
Enter numbers
Access to the Home
menu.
Find the correct viewing
channel
1Press (Standby) to turn on this
product.
2Press DISC to switch to disc mode.
3Turn on the TV and switch to the correct
video-in channel in one of the following
ways:
Go to the lowest channel on your•
TV, then press the Channel Down
button until you see the Philips or
the Home menu screen.
Press the• SOURCE button
repeatedly on the remote control of
your TV.
Tip
The video-in channel is between the lowest•
and highest channels and may be called
FRONT, A/V IN, VIDEO, HDMI etc. See the
TV user manual on how to select the correct
input on the TV.
4 Get started
Insert the remote control
batteries
1On the back of the remote control, slide
the battery cover to remove it.
2Insert the 2 supplied batteries (AAA). Be
sure the + and - ends of the batteries line
up with the markings inside the case.
3Slide the cover back into position.
Note
Do not mix batteries (old and new or carbon•
and alkaline, etc.).
Remove batteries if they are exhausted or if
•
the remote control is not to be used for a long
time.
Batteries contain chemical substances, they
•
should be disposed of properly.
English
EN

18
Tip
You can set the default language for DVD disc,•
see (‘Adjust settings’ > ‘Video Setup’ > [Disc
Menu]).
Set up network
Follow the steps below to help you set up the
network connection for software updates and
enjoy BD-Live applications.
1Connect the home theatre to a
broadband modem or router.
2Turn on your TV and switch to the
correct source for the home theatre.
3Press , select [Settings], and then press
OK.
4Select [Advanced Setup] > [Network] >
[Next].
5Press OK.
The home theatre connects to the»
Internet. If connection fails, select
[Retry], then press OK.
6Select [Finish], then press OK to exit.
Note
Loading BD-Live content from the Internet•
may take some time, depending on the file size
and the speed of the Internet connection.
Use the Home menu
Press (Home menu).
Select•[Play Disc] to start disc play.
Select•[USB] to view the USB contents.
Select•[Settings] to access the setup
menu.
Select menu display language
Note
Skip this setting if this product is connected•
to a HDMI CEC compliant TV. It switches
automatically to the same OSD menu language
as per your TV setting.
1In the Home menu, select [Settings] and
press OK.
2Select [Preference Setup], then press .
3Select [OSD Language], then press OK.
The language options are different•
depending on your country or
region. It may not correspond to the
illustration shown here.
4Press to select a language, then press
OK.
Play Disc USB Settings
Parental Control
OSD Language
Screen Saver
Display Panel
Auto Standby
PBC
Change PIN
Sleep Timer
Nederlands
Français
Deutsch
Italiano
Español
Svenska
Português
English
EN

19
Audio Input Mapping
When you map the connection between
other devices and the audio input jacks of
this Home Theatre System, you can enjoy
the System Audio Control (one-touch audio)
feature.
Map the devices to the audio inputs
Note
Before you start, ensure that the audio output•
of the HDMI TV and other HDMI devices have
been connected to the audio input jacks on
this Home Theatre System.
1Press , select [Settings], then press OK.
2Select [EasyLink Setup], then press .
•[One Touch Play] and [One Touch
Standby] functions are turned on by
default.
3Select [System Audio Control] > [On] .
4Read the on-screen instructions and
press OK to select [Continue].
The Home Theatre System scans and»
displays the valid devices.
5Press OK to select [Continue].
Video Setup
Advanced Setup
Audio Setup
Preference Setup
EasyLink Setup
One Touch Play
EasyLink
One Touch Standby
On
On
System Audio Control Off
Audio Input Mapping
On
Use Philips EasyLink
Your product supports Philips EasyLink, which
uses the HDMI CEC (Consumer Electronics
Control) protocol. EasyLink-compliant devices
that are connected through HDMI connectors
can be controlled by a single remote control.
Note
Philips does not guarantee 100%•
interoperability with all HDMI CEC devices.
1Turn on the HDMI CEC operations on
the TV and other connected devices. See
TVs/devices manual for details.
2You can now enjoy the following Philips
EasyLink controls.
EasyLink
Turn off or turn on all EasyLink features.
One-touch play
When you press PLAY on the remote
control, the TV (if it supports one-touch
play) and the Home Theatre System will be
turned on. Disc play starts if there is a disc
in the Home Theatre System and the TV
automatically switches to the correct channel
to show the video content.
One-touch standby
When you press and hold (Standby) on
the remote control, this Home Theatre
System and all the connected HDMI CEC
devices (if they support one-touch standby)
switch to standby mode simultaneously.
System Audio Control
When you play a device where the audio
output is routed to this Home Theatre
System, this Home Theatre System
switches to the corresponding audio source
automatically.
To use one-touch audio, map the connected
devices correctly to the audio input jacks of
this Home Theatre System.
English
EN