Philips Azure Cordless HI575 User manual

Azur Cordless
HI575, HI571, HI570

2

3

4

ENGLISH 6
POLSKI 17
ROMÂNĂ 29
РУССКИЙ 41
ČEŠTINA 53
MAGYAR 64
SLOVENSKY 75
LIETUVIŠKAI 87
HI575, HI571, HI570

General description (fig. 1)
ATurbo steam button 0(HI575 only)
BSpray button T
CShot-of-steam button 9
DSteam control
0= no steam
1= minimum steam
6= maximum steam
EAuto shut-off light (HI575 only)
FTemperature light
GCarry case (HI575/571 only)
HSoft-touch handgrip (HI575 only)
ICord clip
JPower unit
KMode switch
∫= cordless ironing
π= storage position
ª= corded ironing
LStand
MStand clamp
NFilling cup
OTypeplate
PSoleplate
QWater level window
RTemperature dial
SCalc-Clean button for cleaning/descaling
TFilling opening with cap
USpray nozzle
Important
Read these instructions for use carefully before using the appliance and
save them for future reference.
◗Check if the voltage indicated on the type plate corresponds to
the local mains voltage before you connect the appliance.
◗Only connect the appliance to an earthed wall socket.
◗Do not use the appliance if the plug, the cord or the appliance
itself shows visible damage, or if the appliance has been dropped
or is leaking.
◗Check the cord regularly for possible damage.
◗If the mains cord is damaged, it must be replaced by Philips, a
service centre authorised by Philips or similarly qualified persons
in order to avoid a hazard.
◗Never leave the appliance unattended when it is connected to the
mains.
◗Never immerse the iron and the stand, if provided, in water.
◗Keep the appliance out of the reach of children.
◗The soleplate of the iron can become extremely hot and may
cause burns if touched.
ENGLISH6

◗Do not allow the cord to come into contact with the soleplate
when it is hot.
◗When you have finished ironing, when you clean the appliance,
when you fill or empty the water tank and also when you leave
the iron even for a short while: set the steam control to position
O, put the iron on its heel and remove the mains plug from the
wall socket.
◗Only use this iron with the stand supplied.
◗Always place and use the iron and the stand, if provided, on a
stable, level and horizontal surface.
◗Do not put perfume, vinegar, starch, descaling agents, ironing aids
or other chemicals in the water tank.
◗This appliance is intended for household use only.
Before first use
C1Release the carry case (HI575/571 only).
C2Remove the carry case (HI575/571 only).
3Remove any sticker or protective foil from the soleplate and
clean the soleplate with a soft cloth.
C4Fully unwind the mains cord.
ENGLISH 7
LINEN
HILO
SILK
SEDA
NYLON
NILON
WOOL
LANA
COTTON
ALGODON
MAX
MIN
LINEN
HILO
SILK
SEDA
NYLON
NILON
WOOL
LANA
COTTON
ALGODON
MAX
MIN
LINEN
HILO
SILK
SEDA
NYLON
NILON
WOOL
LANA
COTTON
ALGODON
MAX
MIN

Preparing for use
Fastening the stand clamp
C1Fold out the clamp on the bottom of the stand and fix the
stand clamp to the ironing board or to another stable surface,
such as a tabletop.
The rubber feet on the bottom prevent the stand from slipping.
◗You can also place the stand on the ironing board without using
the clamp.The clamp can then remain folded in.
Do not place the stand close to the table edge, as the stand could
accidentally be knocked over.
Filling the water tank
1Remove the mains plug from the wall socket.
2Set the steam control to 0 (no steam).
C3Set the mode switch to ∫(cordless ironing).
C4Take the iron from the stand.
5Place the iron on its heel and open the cap of the filling
opening.
C6Use the filling cup to pour water into the water tank and close
the cap of the filling opening afterwards.
If the tap water in your area is very hard, we advise you to mix it with
an equal amount of distilled water or to use distilled water only.
Do not fill the water tank beyond the MAX indication.
Do not put perfume, vinegar, starch, descaling agents, ironing aids or
other chemicals in the water tank.
ENGLISH8
LINEN
HILO
SILK
SEDA
NYLON
NILON
WOOL
LANA
COTTON
ALGODON
MAX
MI
N

Setting the temperature
C1Put the iron on the iron stand.
C2Set the required ironing temperature by turning the
temperature dial to the appropriate position (see section 'Tips'
for extra information).
Check the laundry care label for the required ironing temperature:
C3Put the mains plug in an earthed wall socket.The temperature
light goes on to indicate that the iron is heating up.
◗The iron is hot enough when the temperature light goes out.
◗During ironing the temperature light goes on from time to time.
This indicates that the iron is heating up to the right temperature.
◗If you have been ironing at a high temperature and subsequently
set the temperature dial to a lower setting, wait until the
temperature light goes on again before you continue ironing.This
will prevent damage to your fabrics.
◗Some parts of the iron have been lightly greased.This may cause
the iron to give off some smoke when you switch it on for the
first time.After a short while, however, this will cease.
ENGLISH 9
LINEN
HILO
SILK
SEDA
NYLON
NILON
WOOL
LANA
COTTON
ALGODON
MAX
MI
N
Steam setting
0 (see 'Ironing
without steam')
1-2
3-6
Temperature
setting
1
2
3to MAX
Type of fabric
Synthetic fabrics (e.g.
acetate, acrylic,
viscose, polyamide,
polyester) and silk
Wool
Cotton, linen
Please note that Z
on the label means
that the article
cannot be ironed.
Symbol on laundry
care label
B
C
D
Z

Tips
- If the fabric consists of various kinds of fibres, always select the
temperature required by the most delicate fibre, i.e. the lowest
temperature. For example: if an article consists of 60% polyester and
40% cotton, it should be ironed at the temperature indicated for
polyester (2) and without steam.
- If you do not know what kind or kinds of fabric an article is made of,
determine the right ironing temperature by ironing a part that will
not be visible when you wear or use the article.
- Silk, woollen and synthetic materials: iron the reverse side of the
fabric to prevent shiny patches.
- Velvet and other fabrics that tend to acquire shiny patches should be
ironed in one direction only (along with the nap) while applying very
little pressure.
- Start ironing the articles that require the lowest ironing temperature,
such as those made of synthetic fibres.
Using the appliance
Corded ironing
C1Set the mode switch to position ª(corded ironing).
C2Take the iron from the stand.
◗When you stop ironing for a while, you can put the iron on the
stand or on its heel.
Cordless ironing
C1Set the mode switch to position ∫(cordless ironing).
ENGLISH10