Philips GC8700 series User manual

GC8700 series

21 3
6 75
9 8
11 1012
4
13

English 6
Deutsch 18
Español 30
Français 42
Italiano 55
Nederlands 67
Português 79
Suomi 91
Svenska 103

English
Introduction
Congratulations on your purchase and welcome to Philips! To fully benefit
from the support that Philips offers, register your product at
www.philips.com/welcome.
Read this user manual, the important information leaflet, and the quick start
guide carefully before you use the appliance. Save them for future
reference.
Exclusive technology from Philips
OptimalTemp technology
The OptimalTemp technology enables you to iron all types of ironable
fabrics, in any order, without adjusting the iron temperature and without
sorting your garments.
It is safe to just rest the hot soleplate directly on the ironing board without
putting back to the iron platform. This will help reduce the stress on your
wrist.
This iron has been approved by The Woolmark Company Pty Ltd for the
ironing of wool-only products, provided that the garments are ironed
according to the instructions on the garment label and those issued by the
manufacturer of this iron. R1602. In the United Kingdom, Eire, Hong Kong
and India, the Woolmark trademark is a certification trademark.
Compact ProVelocity Technology
This technology delivers continuous steam that penetrates deeply to
remove creases easily. At the same time, it keeps the appliance more
compact and lighter than traditional steam generators, for easier storage.
Product overview (Fig. 1)
1 Water supply hose
2 Steam trigger/Steam boost
3 'Iron ready' light
4 Soleplate
5 Iron platform
6 Carry lock release button
7 Detachable water tank
8 Water supply hose storage compartment
9 Mains cord with plug
10 CALC-CLEAN button with light
6English

11 On/off button with power-on light and auto-off light
12 ECO button with light
13 Smart Calc-Clean container
Preparing for use
Type of water to use
This appliance has been designed to be used with tap water. However, if
you live in an area with hard water, fast scale build-up may occur.
Therefore, it is recommended to use distilled or demineralized water to
prolong the lifetime of the appliance.
Warning: Do not use perfumed water, water from the tumble
dryer, vinegar, starch, descaling agents, ironing aids, chemically
descaled water or other chemicals, as they may cause water
spitting, brown staining or damage to your appliance.
Filling the water tank
1Fill the water tank before every use or when the water level in the water
tank drops below the minimum level. You can refill the water tank at any
time during use.
2Remove the water tank from the base.
3Fill the water tank up to the MAX indication.
7
English

4Put the water tank back into the appliance by fitting the bottom part into
the appliance first.
5Push in the top part of the water tank until it locks into place ('click').
Using the appliance
Ironable fabrics
Do not iron non-ironable fabrics.
Fabrics with these symbols are ironable, for example linen, cotton,
polyester, silk, wool, viscose and rayon.
Fabrics with this symbol are not ironable. These fabrics include synthetic
fabrics such as Spandex or elastane, Spandex-mixed fabrics and polyolefins
(e.g. polypropylene). Prints on garments are not ironable either.
Ironing
1Place the steam generator on a stable and even surface.
Note: In order to ensure safe ironing we recommend to always place the
base on a stable ironing board.
2Make sure that there is enough water in the water tank.
8English

3Put the mains plug in an earthed wall socket and press the on/off button
to switch on the steam generator. Wait until the 'iron ready' light lights up
continuously. This takes approx. 2 minutes.
4Remove the water supply hose from the water supply hose storage
compartment.
5Press the carry lock release button to unlock the iron from the iron
platform.
6Press and hold the steam trigger to start ironing.
Warning: Never direct steam at people.
7For best ironing results, after ironing with steam, perform the last strokes
without steam.
Note: When you use the appliance for the first time, it may take 30 seconds
for steam to come out of the appliance.
Note: The pump is activated each time you press the steam trigger. It
produces subtle rattling sound, which is normal. When there is no water in
the water tank, the pump sound is louder. Fill up the water tank with water
when the water level drops below the minimum level.
For more powerful steam, you can use the TURBO steam mode, which is
safe on all ironable fabrics.
For fabrics such as cotton, jeans and linen, you are recommended to use the
TURBO steam mode.
1Press and hold the on/off button for 2 seconds until the light turns white.
2To deactivate the TURBO mode, press and hold the on/off button for 2
seconds again until the light turns blue.
Steam boost function
Use the steam boost function to remove stubborn creases.
9
English

2x
1Press the steam trigger twice quickly.
Vertical ironing
Warning: Hot steam is emitted from the iron. Never attempt to
remove wrinkles from a garment while someone is wearing it. Do
not apply steam near your or someone else's hand.
You can use the steam iron in vertical position to remove wrinkles from
hanging fabrics.
1Hold the iron in vertical position, press the steam trigger and touch the
garment lightly with the soleplate and move the iron up and down.
Safe rest
Resting the iron while rearranging your garment
While rearranging your garment, you can rest the iron either on the iron
platform or horizontally on the ironing board. The OptimalTemp technology
ensures the soleplate will not damage the ironing board cover.
10 English

Energy saving
Eco mode
By using the ECO mode (reduced amount of steam), you can save energy
without compromising on the ironing result.
1To activate the ECO mode, press the ECO button. The green ECO light
goes on.
2To deactivate the ECO mode, press the ECO button again. The green
ECO light goes out.
Safety auto-off mode (specific types only)
-To save energy, the appliance switches off automatically when it has not
been used for 5 minutes. The auto-off light in the on/off button starts to
flash.
-To activate the appliance again, press the on/off button. The appliance
then starts to heat up again.
Warning: Never leave the appliance unattended when it is
connected to the mains. Always unplug the appliance after use.
Cleaning and maintenance
Smart Calc-Clean System
Your appliance has been designed with a Smart Calc-Clean system to
ensure that descaling and cleaning is done regularly. This helps to maintain
a strong steam performance and prevents dirt and stains coming out of the
soleplate over time. To ensure that the cleaning process is performed, the
steam generator gives regular reminders.
Sound and light Calc-Clean reminder
After 1 to 3 months of use, the Calc-Clean light starts flashing and the
appliance starts beeping to indicate that you have to perform the Calc-
Clean process.
11
English

Besides that, a second defense step to protect the steam generator from
scale is integrated: the steam function gets disabled if descaling is not done.
After descaling is done, the steam function will be restored. This takes place
regardless of the type of water used.
Note: The Calc-Clean process can be performed at any time, even when the
sound and light reminder is not activated yet.
Performing the Calc-Clean process with the Calc-Clean
container
Warning: Do not leave the appliance unattended during the Calc-
Clean process.
Caution: Always perform the Calc-Clean process with the Calc-Clean
container. Do not interrupt the process by lifting the iron up from the
Calc-Clean container, as hot water and steam will come out of the
soleplate.
1Fill up the water tank halfway.
Note: Make sure that the appliance is plugged in and switched ON during
the Calc-Clean process.
2Place the Calc-Clean container on the ironing board or any other even,
stable surface.
3Place the iron stably on the Calc-Clean container.
12 English

2 sec.
4Press and hold the CALC-CLEAN button for 2 seconds until you hear
short beeps.
Note: The Calc-Clean container has been designed to collect scale
particles and hot water during the Calc-Clean process. It is perfectly safe
to rest the iron on this container during the entire process.
2 min.
5During the Calc-Clean process, you hear short beeps and a pumping
sound.
6Wait approximately 2 minutes for the appliance to complete the process.
When the Calc-Clean process is completed, the iron stops beeping and
the CALC-CLEAN light stops flashing.
7Wipe the iron with a piece of cloth and put it back on the base station.
Caution: The iron is hot.
8As the Calc-Clean container becomes hot during the Calc-Clean process,
wait approx. 5 minutes before you touch it. Then carry the Calc-Clean
container to the sink, empty it and store it for future use.
9If necessary, you can repeat steps 1 to 8. Make sure that you empty the
Calc-Clean container before you start the Calc-Clean process.
Note: During the Calc-Clean process, clean water may come out of the
soleplate if no scale has accumulated inside the iron. This is normal.
For more information on how to carry out the Calc-Clean process, refer to
the videos in this link: http://www.philips.com/descaling-iron.
13
English

Cleaning the soleplate
To properly maintain your appliance, clean it regularly.
1Clean the appliance with a moist cloth.
2To easily and effectively remove stains, let the soleplate heat up and
move the iron over a moist cloth.
Tip: Clean the soleplate regularly to ensure smooth gliding.
Storage
1Switch off the steam generator and unplug it.
2Pour the water out of the water tank into the sink.
3Fold the water supply hose. Wind the water supply hose inside the water
supply hose storage compartment and secure it inside the storage hook.
4Fold the mains cord and fasten it with the Velcro strip.
14 English

5Push the carry lock release button to lock the iron onto the iron platform.
6You can carry the appliance with one hand by the handle of the iron
when the iron is locked on the iron platform.
Troubleshooting
This chapter summarizes the most common problems you could encounter
with the appliance. If you are unable to solve the problem with the
information below, visit www.philips.com/support for a list of frequently
asked questions or contact the Consumer Care Center in your country.
Problem Possible cause Solution
The iron does not
produce any steam.
There is not enough water in
the water tank.
Fill the water tank beyond the MIN
indication. Press and hold the steam trigger
until steam comes out. It may take up to 30
seconds until steam comes out.
You did not press the steam
trigger.
Press and hold the steam trigger until steam
comes out.
The steam function has
been disabled until you
have performed the Calc-
Clean process.
Perform the Calc-Clean process to restore
the steam function. (see chapter ' Cleaning
and maintenance')
The water tank is not placed
in the appliance properly.
Fit the water tank back into the appliance
firmly ('click').
At the start of your ironing
session, the steam trigger
has not been pressed long
enough.
Press and hold the steam trigger until steam
comes out. It may take up to 30 seconds
until steam comes out.
The light of the CALC-
CLEAN button flashes
and the appliance beeps.
This is the Calc-Clean
reminder.
Perform the Calc-Clean after the Calc-
Clean reminder is given (see chapter
'Cleaning and maintenance').
15
English

Problem Possible cause Solution
No steam comes out of
the soleplate, the light of
the CALC-CLEAN button
flashes and the appliance
beeps.
You have not done or have
not completed the Calc-
Clean process.
Perform the Calc-Clean process to enable
the steam function again (see chapter
'Cleaning and maintenance').
The appliance has
switched off.
The safety auto-off function
is activated automatically
when the appliance has not
been used for more than 5
minutes.
To activate the appliance again, press the
on/off button. The appliance then starts to
heat up again.
The appliance produces
a loud pumping sound.
The water tank is empty. Fill the water tank with water and press the
steam trigger until the pumping sound
becomes softer and steam comes out of the
soleplate.
Water droplets come out
of the soleplate.
After the Calc-Clean process
remaining water may drip
out of the soleplate.
Wipe the soleplate dry with a piece of cloth.
If the Calc-Clean light still flashes and the
appliance still beeps, perform the Calc-
Clean process (see chapter 'Cleaning and
maintenance').
The Calc-Clean process has
not been completed.
You have to perform the Calc-Clean
process again (see chapter 'Cleaning and
maintenance').
Steam condenses into water
in the hose when you use
steam for the first time or
have not used it for a long
time.
This is normal. Hold the iron away from the
garment and press the steam trigger.Wait
until steam instead of water comes out of
the soleplate.
Dirty water and impurities
come out of the
soleplate.
Impurities or chemicals
present in the water have
deposited in the steam vents
and/or soleplate.
Perform the Calc-Clean process regularly
(see chapter 'Cleaning and maintenance').
Water flushes out of the
soleplate.
You have accidentally
started the Calc-Clean
process (see chapter
'Cleaning and
maintenance').
Switch off the appliance. Then switch it
back on again. Let the iron heat up until the
'iron ready' light lights up steadily.
The Calc-Clean process
does not start.
You have not pressed the
CALC-CLEAN button for 2
seconds until the appliance
started beeping.
See chapter 'Cleaning and maintenance'.
The iron leaves a shine or
an imprint on the
garment.
The surface to be ironed was
uneven, for instance
because you were ironing
over a seam or a fold in the
garment.
PerfectCare is safe on all garments. The
shine or imprint is not permanent and will
come off if you wash the garment.Avoid
ironing over seams or folds or you can place
a cotton cloth over the area to be ironed to
avoid imprints.
16 English

Problem Possible cause Solution
There was not enough felt in
the ironing board cover.
Put an extra layer of felt material under the
ironing board cover.
The ironing board cover
becomes wet, or there
are water droplets on the
floor/garment.
Steam has condensed on
the ironing board cover after
a long ironing session.
Replace the ironing board cover if the foam
or felt material has worn out. You can also
add an extra layer of felt material under the
ironing board cover to prevent
condensation on the ironing board.
You have an ironing board
that is not designed to cope
with the high steam rate of
the appliance.
Put an extra layer of felt material under the
ironing board cover to prevent
condensation on the ironing board.
17
English

Deutsch
Einführung
Herzlichen Glückwunsch zu Ihrem Kauf und willkommen bei Philips! Um die
Unterstützung von Philips optimal nutzen zu können, sollten Sie Ihr Produkt
unter www.philips.com/welcome registrieren.
Lesen Sie diese Bedienungsanleitung, die Broschüre mit wichtigen
Informationen und die Kurzanleitung sorgfältig durch, bevor Sie das Gerät
verwenden. Heben Sie sie zur späteren Verwendung auf.
Exklusive Technologie von Philips
Optimal TEMP-Technologie
Mit der "OptimalTemp"-Technologie können Sie alle bügelechten Textilien
ohne Einstellung der Bügeltemperatur oder Dampfstufe und ohne
Vorsortieren der Kleidung bügeln.
Die heiße Bügelsohle kann sicher direkt auf dem Bügelbrett abgestellt
werden und muss nicht auf die Abstellfläche gestellt werden. Dadurch wird
die Belastung Ihrer Handgelenke verringert.
Dieses Bügeleisen wurde von The Woolmark Company Pty Ltd für das
Bügeln von Wollprodukten unter der Voraussetzung genehmigt, dass die
Kleidungsstücke gemäß den Anweisungen auf dem Etikett des
Kleidungsstücks und den Anweisungen vom Hersteller dieses Bügeleisens
gebügelt werden. R1602. In Großbritannien, Irland, Hong Kong und Indien ist
das Woolmark-Warenzeichen eine Gütemarke.
Kompakte ProVelocity-Technologie
Diese Technologie liefert einen dauerhaften Dampfstrom, der tief ins
Gewebe eindringt und Falten leicht entfernt. Gleichzeitig bleibt das Gerät
kompakter und leichter als bei klassischen Dampferzeugern, wodurch es
einfacher aufbewahrt werden kann.
Produktübersicht (Abb. 1)
1 Verbindungsschlauch
2 Dampfauslöser/Dampfstoß
3 Bereitschaftsanzeige
4 Bügelsohle
5 Bügeleisen-Abstellfläche
6 Entriegelungstaste für Transportverriegelung
7 Abnehmbarer Wassertank
8 Aufbewahrungsfach für Verbindungsschlauch
9 Netzkabel mit Stecker
10 CALC-CLEAN-Taste mit Kontrollleuchte
18 Deutsch

11 Ein-/Ausschalter mit Betriebsanzeige und Anzeige für automatische
Sicherheitsabschaltung
12 ECO-Taste mit Anzeige
13 Intelligenter Calc-Clean-Behälter
Für den Gebrauch vorbereiten
Zu verwendende Wasserart
Dieses Gerät wurde für die Verwendung mit Leitungswasser entwickelt.
Wenn Sie in einem Gebiet mit hartem Wasser leben, kann sich schnell Kalk
ablagern. Daher wird empfohlen, destilliertes oder demineralisiertes Wasser
zu verwenden, um die Lebensdauer des Geräts zu verlängern.
Warnhinweis: Verwenden Sie kein parfümiertes Wasser, Wasser
aus dem Wäschetrockner, Essig, Stärke, Entkalkungsmittel,
Bügelzusätze, chemisch entkalktes Wasser oder andere
Chemikalien, da dies zu Austreten von Wasser, braunen Flecken
oder Schäden am Gerät führen kann.
Den Wasserbehälter füllen
1Füllen Sie den Wasserbehälter vor jedem Gebrauch oder wenn der
Wasserstand im Wasserbehälter unter das Minimum fällt. Während des
Gebrauchs können Sie den Wassertank jederzeit nachfüllen.
2Entfernen Sie den Wasserbehälter von der Basisstation.
3Füllen Sie den Wassertank bis zur MAX-Markierung.
19
Deutsch

4Setzen Sie den Wassertank wieder ein, indem Sie den unteren Teil zuerst
ins Gerät einsetzen.
5Drücken Sie auf den oberen Teil des Wassertanks, bis er hörbar einrastet.
Das Gerät benutzen
Bügelbare Gewebe
Warnhinweis:Bügeln Sie keine Stoffe, die nicht zum Bügeln
geeignet sind.
-Stoffe mit diesen Symbolen sind bügelecht, z. B. Leinen, Baumwolle,
Polyester, Seide, Wolle, Viskose und Reyon.
-Stoffe mit diesem Symbol sind nicht bügelecht. Zu diesen Stoffen
gehören Synthetikfasern wie zum Beispiel Lycra oder Elastan, Lycra-
Mischgewebe und Polyolefine (z. B. Polypropylen). Kleidungsstücke mit
Aufdruck sind ebenfalls nicht bügelecht.
Bügeln
1Stellen Sie die Dampfeinheit auf eine stabile und ebene Unterlage.
Hinweis: Für ein sicheres Bügeln empfehlen wir, den Aufheizsockel immer
auf ein stabiles Bügelbrett zu stellen.
2Stellen Sie sicher, dass sich genügend Wasser im Wassertank befindet.
20 Deutsch