Philips LVL Series User manual

LVL Series
VANDAL-RESISTANT WET/DAMP LOCATION LIGHTING
Page 1 of 2
Job Information Type:
Job Name:
Cat. No.:
Notes:
Features
Illumination: Illumination
is provided by two high-
performance 5.5 W, 6 VDC
MR16-style halogen lamps.
Lamps are held in an attractive
molded swivel assembly, and
are fully adjustable.
Housing: The high-abuse
housing, backplate and
electronics shell are molded
from high-impact, F1 rated,
GE Lexan®polycarbonate. All
injection molded components
meet the UL 94 V-0, 5 VA
flame retardant standard for
emergency lighting products.
All units are supplied standard
with a UL damp location
listing and tamperproof screw
kit. Optional wet location
listed products include a fully
gasketed cover. Installation
is simplified by the use of a
snap-together backplate and
housing. When installed with
the supplied tamperproof
screw kit, removal from
mounting surface, or removal
of outer protective cover is
not possible under normal
service conditions without the
use of a torx T-15 bit. Utility
supply is completed by use of a
modular plug-in wiring harness.
A convenient knockout is
also made available in the top
right section of product to
accommodate 1/2” conduit
(damp location listed units
only).
Operating Temperature
Range: Damp location
50°F (10°C) to 104°F (40°C)
Wet location
41°F (5°C) to 104°F (40°C)
Wet location with heater
-4°F (-20°C) to 104°F (40°C)
Electronics: 120/277 VAC
dual voltage input with surge-
protected, solid-state, fully
automatic, voltage regulated
charger. Charging system is
complete with low voltage
disconnect, AC lockout,
brownout protection and
combination indicator lamp and
illuminated test switch.
Electrical Specifications:
0.05 A (120 VAC)
0.30 A (120 VAC) with heater
option
0.02 A (277 VAC)
0.13 A (277 VAC) with heater
option
Battery
Maintenance free, sealed
lead calcium battery has an
expected service life of 5
years. Upon utility power
failure or brownout, the unit
shall automatically provide
emergency battery power and
maintain the stated illumination
level and output wattage for a
minimum period of 90 minutes.
Code Compliance
UL 924, UL damp location,
and optional UL wet location
listed. NFPA 101, NEC, BOCA,
OSHA and IBC illumination
standards. Meets ADA
specifications for wall mounted
lighting fixtures.
Warranty
Three year full electronics
warranty. One year full plus
four year prorated lead calcium
battery warranty.
LVLW
8.67"
(22.02 cm)
7.66"
(19.46 cm)
3.72"
(9.45 cm)

LVL Series
VANDAL-RESISTANT WET/DAMP LOCATION LIGHTING
Page 2 of 2
Philips Lightolier
e: [email protected]
t: [phone]
w: www.lightolier.com
LVL Series September 17, 2012
Specifications are subject to change without notice.
© Koninklijke Philips Electronics N.V., 2012.All rights reserved.
Job Information Type:
Ordering Information
Series
LV = LVL Series
Damp/Wet Location
Emergency Light
Optics
* The optics layout shown is intended to be used as reference only. Standard reflectances used were 80/50/20. Lightolier is not responsible for site specific conditions that
may alter the results.
Blank = Damp Location Listed
WL = Wet Location Listed
HR = Wet Location Listed with Battery Heater
Location Listing
Accessories (order as a separate item)
T15TPTOOL = Tamperproof Screwdriver
LV
L= Lead Calcium
Battery
W= White
B= Black
BZ = Bronze
Housing Color
Chart represents (2) luminaires mounted on 18’ centers, mounting height 8’ AFF
0.28
3'
L
0.31
0.33
0.31
0.36
0.41
0.35
0.57
0.52
1.04
1.86
1.96
1.56
3.82
3.40
1.58
3.55
2.83
0.90
1.33
0.72
0.26
0.24
0.17
0.14
0.13
0.11
0.20
0.18
0.16
0.14
0.13
0.11
0.26
0.24
0.17
0.90
1.33
0.72
1.58
3.55
2.83
1.56
3.82
3.40
1.04
1.86
1.96
0.35
0.57
0.52
0.31
0.36
0.41
0.28
0.31
0.33
2'
1'
Average initial footcandles at floor = 1.03 Minimum initial footcandles at floor = 0.28
Maximum initial footcandles at floor = 3.82 Maximum to minimum ratio = 13.7:1
9' 9'