Philips VL72 User manual

OUT TO SUPPLY WIRES
SEE NOTE 3
STREET SIDE LABEL
SEE NOTE 5
POLE FASTENERS
SEE NOTES 2 & 6
INSTALLATION:
1) TURN POWER OFF.
2) Loosen pole fasteners on pod, if required.
3) Make fixture wiring connections to supply wires (by others)
- White to White
- Black to Black
- Green to Green
NOTE: Both green ground wires from fixture should be
"bugged" together with incoming supply wire.
4) Slip luminaire post fitter onto pole and ensure wires
are not being pinched.
5) Orient by turning luminaire "street side" via label
supplied on globe fitter (pod).
6) Torque pole fasteners as follows to 7 ft. lbs.
CAUTION! Over torquing of screws may lead to
damage or fatique of fastener.
7) Power to luminaire may now be turned on.
32002016, revision A
INSTALLATION INSTRUCTIONS:
VL71 & VL72
(Fixture)
SAFETY WARNING:
ALWAYS TURN FIXTURE OFF/DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!
Ensure that the AC service is OFF before any installation or maintenance.
Do not switch service to ON until the entire installation is complete.
Philips Lighting Company
200 Franklin Square Drive
Somerset, NJ 08873
Phone (US): 855-486-2216
Phone (CAN): 800-668-9008
TOOLS REQUIRED:
-5/32" Allen Wrench/Driver
-Torque Wrench capable of 7 ft. lbs. torque
This fixture is intended for installation in accordance with the National Electrical Code and local code
specifications. Failure to adhere to these codes and instructions may result in serious injury and/or damage to
the fixture components and void the warranty. These instructions do not purport to cover all details or vairations
in equipment, nor to provide for every possible contingency related to installation, operation, maintenance, or
mounting situation. Should specific problems occur that are not addressed by these instructions, contact your
Sales Representative or distributor for assistance. Retain these instructions for future reference.

POD
(EXISTING)
LOOSEN FASTENERS
TO REMOVE GLOBE
(EXISTING)
CAMDEN ADAPTER
(NEW)
1/4-20 SCREWS
(NEW)
ECOSWAP ASSY
(NEW)
INSTALLATION:
1) TURN POWER OFF.
2) Loosen, but do not remove (4) globe fasteners on pod.
3) Lift globe from fixture.
4) Remove existing ballast assembly.
- Push spring clip to release ballast module, twist ballast
module counter-clockwise, and lift to remove.
- Disconnect blue power quick disconnect.
5) Remove ballast assembly ring by removing existing screws.
6) Remove terminal block and bracket (if applicable)
7) Assemble Ecoswap to camden adapter by twisting
clockwise until spring clip snaps into place.
8) Make proper wiring connections.
NOTE: In many cases, you may need to remove existing
blue power disconnect to "bug" wires.
9) Install entire unit onto fixture with (2) 1/4-20 screws while
ensuring wires are not being pinched.
NOTE: For Type 3 distribution modules, rotate to orient
"Street Side (SS)" identification located on
Ecoswap, toward street.
10) Carefully lower globe onto fixture.
11) Tighten (4) globe fasteners to secure globe.
REFERENCE: Please see enclosed Power Selection drawing
to adjust wattage output of Ecoswap module.
32002016, revision A
INSTALLATION INSTRUCTIONS:
V71 & V72
(Retrofit)
SAFETY WARNING:
ALWAYS TURN FIXTURE OFF/DISCONNECT POWER AND ALLOW
TO COOL BEFORE PERFORMING ANY MAINTENANCE
Philips Lighting Company
200 Franklin Square Drive
Somerset, NJ 08873
Phone (US): 855-486-2216
Phone (CAN): 800-668-9008
TOOLS REQUIRED:
-1/2" Socket/Driver
-5/32" Allen Wrench/Driver
-Philips Head Screw Driver