Philips UPC Direct DSR4101/58 User manual

DSR 4101_02/2005.qxd 4/02/05 8:13 Page 1

DSR 4101_02/2005.qxd 4/02/05 8:13 Page 2

WARNING 3
The warning sticker is under the product.
Bezpeãnostní oznaãení se nachazí na spodní ãásti pfiístroje.
A figyelmeztet ö címke a készülék alján találhat
Zariadenie nemôÏe byÈ vystavené kvapkaniu alebo striekaniu
kvapaliny a objekty, ktoré sú naplnené tekutinou, ako napr.
váza, nesmú byÈ naÀ umiestÀované.
Bezpeãnostné oznaãenie sa nachádza na spodnej ãasti prístroja.
DSR 4101_02/2005.qxd 4/02/05 7:57 Page 3
Neotvárat'!

English
4WELCOME TO DIGITAL TELEVISION
Welcome to digital television
Your new DSR
Television was never before like this! Your Philips Digital Satellite
Receiver, or DSR for short, opens the door to the fascinating world
of satellite reception through UPC Services, with its dozens of
channels delivered directly to your home by satellite. All with
perfect, digital-quality pictures and CD-quality sound.
Using your Philips DSR to receive UPC Services makes viewing
easier, with much more information and guidance, and much more
control over what you - and the members of your family - watch.
The system
Your DSR works in conjunction with your TV set, Smart Card, and
satellite dish. You can still receive terrestrial TV broadcasts in the
usual way.
The satellite dish is an integral part of the system. Provision of the
digital satellite service and the functioning of the DSR are
conditional on the erection, installation and setting up of the dish
by an authorized installer.
Your DSR has an internal modem for digital information transfer
via your telephone line. The modem is used for purchasing Pay TV
programs, but also for service purposes. Do not forget to connect
this modem to the telephone socket in addition to your regular
telephone.
For future reference, record the serial number of your DSR and
Smart Card together with the installer’s name, address and
telephone number. The serial number of the DSR can be found on
the unit’s rear panel.
Your DSR User Manual
This User Manual gives you the information you need to install
your Philips DSR. We recommend that you first read this manual
through completely to make sure that you get the full benefit
from your DSR.
Information and screens can vary compared to what is shown in
this manual due to that the operator are regularly making new
software with more function available automatically over the air
which enables the DSR to always be more up to date.
DSR 4101_02/2005.qxd 4/02/05 8:13 Page 4

English
ENVIRONMENTAL SPEC SHEET 5
Environmental spec sheet
Meaning of symbols
The “Batteries marking symbol”means used batteries
must not be disposed together with your household
waste.
Please, inquire about the local regulations regarding
disposal of used batteries.
For information: the Philips batteries supplied with
your receiver remote do not contain hazardous
substances such as Mercury, Cadmium, or Lead.
The “Material recyclability symbol ”means the
package cardboard or User manual paper is
recyclable.
The “Material recyclability symbol ”affixed on plastic
parts means these parts are recyclable.
The “Green point”affixed on cardboard means
PHILIPS pays a financial duty to the “Avoidance and
Recovery of Packaging Waste”organization.
This receiver contains a large number of materials
that can be recycled. If you are disposing of an old
machine, please take it to a recycling centre.
The “Warning”symbol means the recommendations
must be read carefully.
02
DSR 4101_02/2005.qxd 4/02/05 8:13 Page 5

English
6CONTENTS
Welcome to digital television 4
Environmental spec sheet 5
Safety instructions 7
Product description 8
Supplied equipment 8
Front View 9
Rear View 10
Connections 11
Standard Connections 11
Connection to a TV and VCR via A/V
Euroconnector Sockets
11
Connection to a stereo system 12
Connecting the modem to the
telephone line
13
Connection to the mains 14
Remote control 15
Fitting Batteries 15
Using the remote control in digital
TV mode
16
Smart Card 17
Insertion 17
Removal 17
Installation 18
Switching on for the first time 18
Checking the signal 19
Searching for channels 20
Day-to-day operation 21
Switching on and off 21
Changing channel 21
Displaying the channel banner 22
Displaying extra programme information 22
Using the TV and radio channel lists 23
Changing the audio language 24
Changing the subtitle language 25
Interactive features 25
Watching other channels while you are
recording a digital satellite programme
26
Switching between digital satellite TV
and terrestrial TV
27
Error messages 27
Setup 28
Displaying the Main Menu 28
Using the Setup menus 28
Using the Control Settings menu 29
About your PIN code 30
Changing your PIN code 30
Setting the age lock level 30
Resetting an age lock level 32
Locking channels 32
Resetting channel locks 33
Smart card 34
Changing the language settings 34
Changing the TV settings 35
Using the Signal Settings menu 36
Checking the signal quality 37
Channel auto-search 37
Channel Manual Search 38
Viewing set-top box information 39
Restoring the factory settings 39
Troubleshooting 40
Specifications 41
Contents
DSR 4101_02/2005.qxd 4/02/05 8:13 Page 6

English
SAFETY INSTRUCTIONS 7
Safety instructions
All the safety and operating instructions should be read and
understood before the receiver is operated.
For safe operation and optimal lifetime
- Position your receiver away from radiators or other heat sources.
- Leave a space of at least 3 cm around the receiver for ventilation
making sure that the ventilation holes are not obstructed.
- This receiver is intended for use in a domestic environment only
and should never be operated or stored in excessively hot,
humid or damp conditions.
- Make sure no objects or fluids enter the housing through the
ventilation slots. Should this happen, disconnect your receiver
from the mains and consult your dealer.
- For cleaning, use a damp chamois leather. Never use any
abrasive cloth, sponge or cleaner.
- When connecting or disconnecting cables to the receiver, always
ensure the receiver is disconnected from the mains.
- Do not disassemble the equipment. There are no user serviceable
parts.
Mains connection
Before connecting the receiver to the mains, check that the mains
supply voltage corresponds to the voltage printed on the rear of
the receiver. If the mains voltage is different, consult your dealer.
If the receiver will not be used for a long time, unplug the power
cord from the wall socket.
Please wait before connecting your receiver - read on.
This product incorporates copyright protection technology that is
protected by U.S. patents and other intellectual property rights.
Use of this copyright protection technology must be authorized
by Macrovision, and is intended for home and other limited
viewing uses only unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is prohibited.
DSR 4101_02/2005.qxd 4/02/05 8:13 Page 7

English
8PRODUCT DESCRIPTION
Product description
Supplied equipment
First check and identify the contents of your Digital Satellite
Receiver package, as listed below:
- Digital Satellite Receiver
- Infrared (IR) Remote Control with separately
packed batteries
- Power Cable
- Telephone Cable
- A/V Euroconnector Cable
- User Manual
If any item is damaged or missing, please inform your supplier
without delay.
Plastic bags can be dangerous. To avoid suffocation keep
the bag away from babies and children.
Power Cable
Telephone Cable
A/V Euroconnector Cable
DSR 4101_02/2005.qxd 4/02/05 8:13 Page 8

English
PRODUCT DESCRIPTION 9
Front View
1 LED indicator
2 Smart Card slot
3 TV/Radio button
4 Option button
5 OK button
6 Standby button
7 Left arrow button
8 Down arrow button
9 Right arrow button
10 Up arrow button
Q
WERTYUIOP
DSR 4101_02/2005.qxd 4/02/05 8:13 Page 9

English
10 PRODUCT DESCRIPTION
Rear View
1 230-240 V ~ 50 Hz mains inlet (**)
2 Label showing the type and serial number of the receiver
3 A/V Connector for TV connection (*)
4 A/V Connector for VCR connection (*)
5 DIGITAL audio output for audio system connection (*)
6 LEFT-RIGHT audio outputs for audio system connection (*)
7 RS 232 serial connector (*)
8 SAT IN for satellite dish connection (*)
9 Telephone line socket for modem connection (***)
(*) SELV: Safety Extra Low Voltage.
(**) HV: Hazardous Voltage.
(***) TNV3: Telecommunication Network Voltage 3.
QWE R TYUIO
DSR 4101_02/2005.qxd 4/02/05 8:13 Page 10

English
CONNECTIONS 11
Connections
Standard Connections
Refer to the User Manuals for your TV, VCR, stereo system and any
other relevant equipment as necessary to make the optimal
connections in your situation.
For both A/V Euroconnector and antenna connections, the VCR
must be connected between the DSR and the TV.
Connection to a TV and VCR via A/V
Euroconnector Sockets
Connect the A/V Euroconnector on the DSR rear panel to the
corresponding socket on the TV using the cable supplied.
PHILIPS
PHILIPS
IN
IN
ANTENNA IN
TV VCR
Supplied
SCART lead
SCART lead
(not supplied)
TV OUT
ANTENNA
IN
Lead from
satellite dish
Lead from you
r
TV antenna
DSR 4101_02/2005.qxd 4/02/05 8:13 Page 11

English
12 CONNECTIONS
Connection to a stereo system
Connect the R-L analogue audio outputs on the DSR rear panel to
the corresponding inputs on your stereo system. Alternatively,
connect the digital audio output on the DSR rear panel to the
corresponding input on your stereo system.
CAUTION!
DO NOT CONNECT THE DSR’S AUDIO SOCKETS TO THE PHONO
SOCKETS OF YOUR STEREO SYSTEM.
DSR 4101_02/2005.qxd 4/02/05 8:13 Page 12

English
CONNECTIONS 13
Connecting the modem to the
telephone line
This equipment has been approved for a connection to the Public
Switched Telephone Network (PSTN) of the following countries:
Hungary, Czech Republic and Slovakia. Optimal functioning can
not be guaranteed in other countries.
Due to differences between the individual PSTNs provided for in
different countries, the approval does not, of itself, give an
unconditional assurance of successful operation on every PSTN
network termination point.
In the event of problems, you should contact your equipment
supplier in the first instance.
The DSR is supplied with a telephone cable used to connect the
telephone line socket on the DSR rear panel to the telephone wall
socket.
- Remove your telephone connector from the telephone wall
socket.
- Insert your telephone cable connector in the telephone line
socket on your DSR.
- Select the correct adapter for your location (see adapters below -
not supplied).
Note: the cable supplied with your DSR has standard RJ-45 terminals.
Therefore if the cable and socket are compatible it is not necessary to
use an adapter.
Adapter for HungaryAdapter for Czech republic and Slovakia
DSR 4101_02/2005.qxd 4/02/05 8:13 Page 13

English
14 CONNECTIONS
- Insert the other end of the telephone cable into the correct
socket on the adapter.
- Plug the adapter into the telephone wall socket.
- Plug your telephone connector into the adapter.
Note: for proper functioning of the modem, it has to be connected to an
analogue telephone line. Please make sure the telephone line you
connect the modem to is an analogue telephone line (PSTN) and not a
digital one (ISDN). If you are not sure, please contact your telephone
company.
There is no telephone communication possible when the modem of the
set is transferring data over the telephone line (this can be recognized
when you pick up the phone and hear constant noise). In case of an
emergency you can stop the modem by disconnecting the modem cable
or the power cable from the rear of the set.
Connection to the mains
- Once you have made all other connections, connect the power
cable into the DSR mains inlet.
- Plug the other end of the power cable into an AC outlet.
After a few seconds the DSR display indicates that it is connected
and in Standby mode.
Note: When not in use, it is highly recommended that the DSR be left in
Standby and the Smart Card in place to allow automatic retrieval of
updated information and authorisations.
CAUTION!
NEVER MAKE OR CHANGE CONNECTIONS AFTER CONNECTING
THE POWER CABLE. ONLY A QUALIFIED SERVICE ENGINEER
SHOULD REMOVE THE COVER OR ATTEMPT TO SERVICE THIS
DEVICE.
DSR 4101_02/2005.qxd 4/02/05 8:13 Page 14

English
REMOTE CONTROL 15
Remote control
Fitting Batteries
- Click open the battery compartment cover.
- Insert two AA (R6 or UM-3) batteries as indicated inside the
battery compartment.
- Close the cover.
CAUTION!
DO NOT MIX OLD AND NEW BATTERIES, AND NEVER MIX
DIFFERENT TYPES OF BATTERY (STANDARD, ALKALINE, AND SO ON).
BATTERIES ARE REMOVABLE FROM THE REMOTE WITH COMMON
HOUSEHOLD TOOLS (E.G. SCREWDRIVER).
Do not dispose of the batteries with
your household waste.
DSR 4101_02/2005.qxd 4/02/05 8:13 Page 15

English
16 REMOTE CONTROL
Using the remote control in digital TV mode
Standby
Standby / ON
0-9
Change channels and enter
numbers
MENU
Open/Close main menu
Colour buttons (red,
green, yellow and blue)
Perform various functions
depending on what is
displayed on your TV screen
OPTS
Open channel option
selection menu
Information i
Display channel banner
and extra programme
information
EXIT
Exit a menu or on-screen
display
OK
Confirm a choice or make a
selection
VOLUME +/ -
Volume up / down
Mute
Turn sound on or off
Teletext
Display teletext or subtitles
when available
F1-F5
Function keys for future use
PAGE +
Scroll one page up
BACK
Go back one step, to the
previous menu or screen
tyu i Move the
highlight around the screen
Channel +/-
Channel up/down
PAGE -
Scroll one page down
TV/RAD
Digital TV/digital radio
TV/SAT
Switch between digital
satellite TV and analogue
terrestrial TV
GUIDE
Display the UPC Electronic
Programme Guide
DSR 4101_02/2005.qxd 4/02/05 8:13 Page 16

English
SMART CARD 17
Smart Card
You must insert the Smart Card to make the DSR operative.
CAUTION!
THE CARD IS FRAGILE.
ALWAYS INSERT IT CAREFULLY AND CORRECTLY.
DO NOT BEND.
DO NOT REMOVE AND RE-INSERT UNNECESSARILY.
NEVER SUBMERGE IN LIQUID OR APPLY CLEANING FLUID.
DO NOT PUSH OTHER CARDS OR OBJECTS INTO THE SLOT.
Insertion
- Hold the card with the gold contact area facing upwards and
pointing towards the slot in the front panel.
- Gently push the card into the slot until it meets the stop.
Removal
Gently withdraw the card from its slot.
Note: You cannot use the set-top-box if you do not have a smart card inserted
in the slot.
DSR 4101_02/2005.qxd 4/02/05 8:13 Page 17

English
18 INSTALLATION
Installation
Switching on for the first time
When you connect your set-top box to the mains, all the lights on
the front panel will light up. After around 10 seconds, all except the
standby light go out. After around 10 more seconds, your set-top
box is switched on, out of standby, and the standby light is green.
- Make sure your TV is switched on.
If the Countries screen below displays, your TV is ready for digital
satellite channels.
You can now continue the installation.
The Countries screen is displayed on your TV screen.
1. Take your remote control. If you have not already inserted the
batteries, do so now (see page 15).
2. Press
t or y until the country you want is highlighted, then
press OK.
A Welcome screen now displays.
3. To change the country selection, press BACK (then repeat step 2),
or to confirm your choice, press OK.
Notes: If the LED is blinking, it indicates that a free over the air upgrade of your
receiver is taking place/ Do not interrupt this operation which may last
several minutes. Wait until the LED stops blinking.
If the Countries screen does not display, try selecting your TV’s ‘AV
input’.
DSR 4101_02/2005.qxd 4/02/05 8:13 Page 18

English
INSTALLATION 19
Checking the signal
Once you have confirmed the language, the Signal Quality screen
displays. You use this screen to confirm that your set-top box is
receiving a satellite signal.
Your set-top box is preset in the factory with the correct LNB
settings to receive signals the applicable satellite.
The details on the screen show the strength and quality of the
signal being received from this satellite.
Your set-top box must receive both a signal strength and a signal
quality of at least 60% in order to successfully find channels.
DSR 4101_02/2005.qxd 4/02/05 8:13 Page 19

English
20 INSTALLATION
Searching for channels
Once you have confirmed the satellite signal strength, the
Channel Auto-Search screen displays.
1. To start the channel search, press OK.
A progress screen displays to confirm that the search is taking
place. When the search is complete, a screen displays to tell you
the number of TV and radio channels that your set-top box has
found.
2. To confirm these channels and display the next screen, press OK.
DSR 4101_02/2005.qxd 4/02/05 8:13 Page 20