Philips R111 User manual

◗Ordering Information
Ordering Code CDM-R 111 35W/830 10DG
ANSI Designation M130/O
Product Number 13554- 1
Description MasterColor Ceramic
Metal Halide
Package Quantity 6
◗hysical Characteristics
Bulb Size R111
Bulb Finish FacetedAluminum
Base GX8.5
Max.Overall ength (MO ) 3.74" (95mm)
ight Center ength ( C ) N/A
Arc ength N/A
ArcTube Material PolycrystallineAlumina
Maximum PermissibleTemperatures:
Base/NeckTransition 150ºC (302ºF)
Neck/Reflector 200ºC (392ºF)
TopAnti-glare Cap 350ºC (662ºF)
◗Operating Characteristics ( hotometric)
Approx. Initial umens11400
Approx. Mean umens2900
RatedAverage ife, Hours311,000
Correlated ColorTemperature (CCT) 3000 K
CIE ChromaticityApproximate x-.433,y-.402
Color Rendering Index (CRI) 81
Efficacy (lpw) 37
MBCP (Maximum Beam Candlepower) 35,000
BeamAngle (at 50% of MBCP) 10º
◗Operating osition
Universal
Note: Operate lamp only on approved thermally
protected electronic ballast.
▼
▼
▼
▼
▼
▼
4 Ft.
FC=2188
ø=8 in.
CDM-R111
35000 MBCP
10
º
3000K Spot
FC=972
ø=13 in.
FC=547
ø=17 in.
FC=350
ø=21 in.
FC=243
ø=25 in.
FC=179
ø=29 in.
FC=137
ø=34 in.
FC=88
ø=42 in.
6 Ft.
8 Ft.
10 Ft.
12 Ft.
14 Ft.
▼
▼
16 Ft.
20 Ft.
112 mm (4.4") MAX
95 mm (3.74") MAX
Beam spread at 50% Maximum Beam Candlepower—0º primary angle
FC=Footcandles at mounting height
ø=Beam diameter at mounting height
MasterColor®Ceramic Metal Halide
38Watt R111 Reflector Spot amp
with FadeBlock™UV Filtering

MasterColor®Ceramic Metal Halide 38Watt R111 Reflector Spot Lamp with FadeBlock™
Electrical Data (Subject to change without notice)
ampWatts(Nominal).............................38
amp OperatingVoltage (rms) (Nominal)4.............88
Initial ampVoltage Range (rms)5.....................80-100
amp Operating Current (Amps) (rms) (Nominal) . . . . . 0.53
amp Current Crest Factor (Maximum) . . . . . . . . . . . . . . 1.8
Warm-upTime to 80% of Output . . . . . . . . . . . . . . . . . . . 3 Minutes
Re-strikeTime for Hot amp . . . . . . . . . . . . . . . . . . . . . . . . 4-8 Minutes
BallastType (Electronic Only). . . . . . . . . . . . . . . . . . . . . . . . ANSI M130/O
Ballast Open CircuitVoltage (Minimum). . . . . . . . . . . . . . . 198
PulsePeakVolts...................................3000Min.,4000Max.
PulseWidth @ 90% Peak . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Micro Second Minimum
Pulse Repetition Rate (Minimum)6....................1perHalfCycle
Minimum OperatingTemperature . . . . . . . . . . . . . . . . . . . . -30ºC (-22ºF)
1) Measured at 100 hrs. life.Approximate lumen values listed are for vertical operation of the lamp.
2) Approximate lumen output at 40% of lamp rated average life.
3) Rated average life is the life obtained, on the average, from large representative groups of lamps in laboratory tests under controlled conditions at 10 or more operating hours per start. It is based on survival of at least 50%
of the lamps and allows for individual lamps or groups of lamps to vary considerably from the average.
4) Measured at rated lamp watts on a linear reactor. PW does not include ballast losses.
5) Measured with the lamp operating at rated watts.
6) Option-PulseWidth @ 90% Peak,1 micro second minimum with 2 pulses per half cycle.
hilips Lighting Company
200 Franklin Square Drive
.O. Box 6800
Somerset, NJ 08875-6800
1-800-555-0050
ADivision of Philips Electronics NorthAmerica Corporation
Updated 6/07 TDS-135541
hilips Lighting
281 Hillmount Road
Markham, Ontario
Canada L6C 2S3
1-800-555-0050
A Division of Philips Electronics td.
www.philips.com
Warnings,Cautions and Operating Instructions
R“WARNING: These lamps can cause serious skin burn and eye inflammation from short wave ultraviolet radiation if outer envelope of the lamp is broken or
punctured. Do not use where people will remain for more than a few minutes unless
adequate shielding or other safety precautions are used.Certain lamps that will automatically
extinguish when the outer envelope is broken or punctured are commercially available.”
This lamp complies with FDA radiation performance standard 21 CFR subchapter J.
(USA:21CFR 1040.30 Canada:SOR/DORS/80-381)
If the outer bulb is broken or punctured, turn off at once and replace the lamp
to avoid possible injury from hazardous short wave ultraviolet radiation. Do
not scratch the outer bulb or subject it to pressure as this could cause the
outer bulb to crack or shatter. A partial vacuum in the outer bulb may cause
glass to fly if the envelope is struck.
WARNING: The arc-tube of metal halide lamps are designed to operate under high
pressure and at temperatures up to 1000º C and can unexpectedly rupture due to
internal or external factors such as a ballast failure or misapplication. If the arc-tube
ruptures for any reason, the outer bulb may break and pieces of extremely hot glass might
be discharged into the surrounding environment. If such a rupture were to happen, THERE
IS A RISK OF ERSONAL INJURY, RO ERTY DAMAGE, BURNS AND FIRE.
These lamps are designed to retain all the glass particles should an arc tube
rupture occur.The following operating instructions are recommended to
minimize these occurrences.
RELAM FIXTURESAT OR BEFORETHE END OF RATED LIFE.Allowing
lamps to operate until they fail is not advised and may increase the possibility
of inner arc tube rupture.
This lamp contains an arc tube with a filling gas containing less than 10 nCi of
Kr-85 and is distributed by hilips Lighting Company, a division of hilips
Electronics North America Corporation, Somerset, New Jersey, 08875.
CAUTION: TO REDUCETHE RISK OF PERSONA INJURY, PROPERTY DAMAGE,
BURNS AND FIRE RESU TING FROM AN ARC-TUBE RUPTURE THE FO OWING
LAM O ERATING INSTRUCTIONS MUST BE FO OWED:
LAM O ERATING INSTRUCTIONS:
1. RE AMP FIXTURESAT OR BEFORETHE END OF RATED IFE.Allowing lamps to operate
until they fail is not advised and may increase the possibility of inner arc tube rupture.
2. Before lamp installation/replacement, shut power off and allow lamp and fixture to cool
to avoid electrical shock and potential burn hazards.
3. Use only auxiliary equipment meeting Philips and/or ANSI standards. Use within voltage
limits recommended by ballast manufacturer.
A.Operate lamp only within specified limits of operation.
B. For total supply load refer to ballast manufacturers electrical data.
C.Operate 39W AR-20 and AR-30L lamps only on thermally
protected ballast.
D.Operate CDM-R111 lamp only on approved thermally protected
electronic ballast.
4. Periodically inspect the outer envelope. Replace any lamps that show scratches,
cracks or damage.
5. If a lamp bulb support is used, be sure to insulate the support electrically to avoid
possible decomposition of the bulb glass.
6. Protect lamp base, socket and wiring against moisture, corrosive atmospheres
and excessive heat.
7. Time should be allowed for lamps to stabilize in color when turned on for the first time.
This may require several hours of operation, with more than one start. amp color is also
subject to change under conditions of excess vibration or shock, and color appearance
may vary between individual lamps.
8. amps may require up to 10 minutes (4–8 minutes for CDM-R111) to re-light if there is a
power interruption.
9. Take care in handling and disposing of lamps. If an arc tube is broken, avoid skin contact
with any of the contents or fragments.
10.For proper installation and removal,lamp should be handled by the sides of the reflector
and not by the aluminum front anti-glare cap.