Philips MCM204/12 User manual

CR2025
Quick Start Guide
Step B
Step A
Enjoy
Setup
1
Quick Start Guide
What’s in the Box?
You should find these items upon opening the box.
MW antenna
Quick Start Guide
Pull out the insulation
plastic sheet.
2
User Manual
User manual
Remote Control
MCM204
MCM204 QUG_Eng 12/1/07, 11:281

Step A Setup
1
2
3
Connection
5
1
2
3
4
Setting the clock
For radio reception, connect the supplied MW antenna to the
MW aerial terminal.
Connect the speaker wires to the SPEAKERS terminals.
Connect the power cord of the system to the
AC power outlet.
In standby mode, press and hold DISPLAY/CLOCK
(CLOCK on the remote control) for 2 seconds.
The clock digits for the hours flash.
Press TUNING ¡1 / 2™ to set the hours.
Press DISPLAY/CLOCK again.The clock digits for the minutes flash.
Press TUNING ¡1 / 2™ to set the minutes.
Press DISPLAY/CLOCK to confirm the time.
speaker
(right)
speaker
(left)
FM wire antenna MW loop
antenna
AC power cord
FM
AERIAL
AM
AERIAL
AU
HEADPHON
X
E
1
2
3
MICRO SYSTEM MCM204
ALBUM/
Tip:
It is unnecessary to
connect the FM pigtail
antenna since it is
fixed to the main unit.
MCM204 QUG_Eng 12/1/07, 11:282

1
2
3
4
5
Tip:
Detailed playback features and
additional functions are described in
the accompanied owner's manual.
Step B Enjoy
Playing a disc
1
2
Select TUNER source.
Press PROG on the remote control for more than two seconds to program all available stations
in order of waveband.
Press ALBUM/PRESET 4 3 until the desired preset station is displayed
Programming and tuning to radio stations
3
Select CD source.
Press OPEN/CLOSE on the top of the system to open the CD door.
Insert a disc with the printed side facing up and press down
on OPEN/CLOSE to close the CD door.
PressÉÅto start playback.
Press 9to stop playback.
Notes for the remote control:
– First, select the source you wish to
control by pressing one of the source select
keys on the remote control (DISC or AUX,
for example).
–Then select the desired function ( 2;,
í, ëfor example).
MCM204 QUG_Eng 12/1/07, 11:283

Step B Enjoy
2007 CKoninklijie Philips Electronics
N.V. All rights reserved.
http://www.philips.com PDCC-JH-0702
Playing a USB mass storage device
1
2
3
4
5
Make sure that your MCM204 is being powered on.
Press SOURCE repeatedly (or USB on the remote) to enter USB mode.
The LCD display shows - - - with USB DIRECT.
Plug a compatible USB mass storage device to MCM204’s USB port marked .
If needed, use a suitable USB cable to connect between the device and MCM204’s USB port.
The device will automatically power on.
PressÉÅon your MCM204 to start playback.
Press 9to stop playback.
Tip:
Refer to the user manual supplied for
the description about compatibility of
USB mass storage device, and
playability of the files stored on the
USB device.
Notes for USB usage:
–This micro system is able to support most USB mass storage devices on the current market.
–In case this micro system fails to identify your USB device, please unplug it and then plug it again. For
USB devices designed with batteries, if the problem remains, please ensure sufficient power supply to
your USB devices by replacing/recharging the batteries.
–You may not be able to play bought tracks in your USB device through this system, such as those
bought from the Apple iTunes or Microsoft PlaysForSure websites!
–This micro system is designed for playback of digital music formats MP3 andWMA only and does not
support WMA-DRM,AAC,WAV, M4a, M4b etc.
–Never try to connect this micro system with your PC through a USB cable to avoid any possible
damage!
MCM204 QUG_Eng 12/1/07, 11:284