Philips SWW1890/12 User manual

Register your product and get support at
www.philips.com/welcome
SWW1890
EN User manual

3
Contents
EN
Contents
1 Important 4
Safety 4
2 Your Philips Wireless HD Net Connect 5
What is in the box 5
3 Overview 6
The transmitter 6
The receiver 6
4 Installation 8
Connect the transmitter to your computer 8
Connect the receiver to the HDTV set 8
5 Activate your Philips Wireless HD
Net Connect and set up the link 9
Turn on the power of your HDTV 9
Activate the wireless link 9
On screen display on HDTV 10
6 Mount your receiver 11
Mount your receiver on the wall 11
Mount your receiver on the back of the
HDTV 12
7 Technical data 13
Supported resolution 13
Product specications 13
8 Notice 14
Declaration of conformity 14
Compliance with EMF 14
Environmental-Recycling the product 14
Warranty information 15
9 Frequently asked questions 16
English

4
other apparatus (including ampliers) that
produce heat.
iProtect the power cord from being
walked on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
j Only use attachments/accessories specied
by the manufacturer.
kUnplug this apparatus during lightning
storms or when unused for long periods of
time.
l Refer all servicing to qualied service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
mApparatus shall not be exposed to
dripping or splashing.
nDo not place any sources of danger on the
apparatus (e.g. liquid lled objects, lighted
candles).
Warning
•Use only the provided power adapter.
1 Important
Safety
This ‘bolt of lightning’ indicates uninsulated
material within your unit may cause an electrical
shock. For the safety of everyone in your
household, please do not remove product
covering.
The ‘exclamation point’ calls attention to
features for which you should read the enclosed
literature closely to prevent operating and
maintenance problems.
WARNING: To reduce the risk of re or electric
shock, this apparatus should not be exposed to
rain or moisture and objects lled with liquids,
such as vases, should not be placed on this
apparatus.
Important Safety Instructions
aRead these instructions.
bKeep these instructions.
cHeed all warnings.
dFollow all instructions.
eDo not use this apparatus near water.
fClean only with dry cloth.
gDo not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
hDo not install near any heat sources such
as radiators, heat registers, stoves, or
EN

5
USB cable for the power supply of the
transmitter (0.5 meters)
Power adapter for the receiver
Anchors x 2
Screws x 2
Adhesive tape x 2
Quick Installation Guide
Quick start guide
User manual
2 Your Philips
Wireless HD
Net Connect
Congratulations on your purchase and welcome
to Philips!
To fully benet from the support that
Philips offers, register your product at
www.philips.com/welcome.
What is in the box
Note
•Make sure you have all these items in the box. Contact
your dealer for any missing or damaged items.
Transmitter
Receiver
HDMI cable (1.5 meters)
EN
English

6
The receiver
Top view
1 LED
indicator
Displays the status of the
receiver.
2Power
button
with LED
indicator
Press to turn the receiver on/
off or to standby mode.
3INFO
button
Displays on the HDTV the
connection status of the
receiver.
Rear view
1DC IN
connector
Connect the power adapter
of the receiver.
2HDMI OUT
connector
Connect to the HDTV with
an HDMI cable
3 Overview
The transmitter
Front view
POWER
1 LED
indicator
Displays the connection status
of the transmitter.
2 USB
power jack
Connect the transmitter to
the computer with the USB
cable.
Top view
1INFO
button
Displays on the HDTV the
connection status of the
transmitter.
2 HDMI IN
connector
Plug into the HDMI port of
the computer.
EN

7
The Philips Wireless HD Net Connect gives
you a total wireless solution to enjoy the
content from your computer on your HDTV.
The transmitter can transmit an uncompressed
video content up to 7 meters (without
obstruction between the transmitter and
receiver) without latency. The receiver can
receive signals for viewing on your HDTV. All
you need to do is to:
• Connect the transmitter to your computer.
• Connect the receiver to your HDTV set.
EN
English

8
3Connect the other end of the USB cable
to your the USB port of your computer.
Note
•For some computers, the HDMI and USB ports are
located in different sides of the computer.
»The power LED indicator of the
transmitter ashes in blue, then turns
into solid blue when the connection is
established.
Connect the receiver to the
HDTV set
HDMI
HDMI
1Connect the receiver with the supplied
HDMI cable:
• Connect one end of the HDMI cable to
HDMI OUT connector of the receiver.
• Connect the other end of the HDMI
cable to the HDMI in connector of
your HDTV.
2Connect the power adapter to the
receiver with the supplied power adapter:
• Connect one end of the power
adapter to the DC IN connector of
the receiver.
• Connect the other end of the power
adapter to a power socket.
4 Installation
Connect the transmitter to
your computer
a
bc
Connect the transmitter to the computer using
the supplied USB cable.
1Connect the transmitter to the HDMI port
of the computer.
2Connect the small end of the USB cable to
the POWER jack of the transmitter;
EN

9
Establish the link between the
transmitter and receiver
• A ashing blue power LED is displayed
until the signal link between the two units
is established. Normally, it takes around
15-20 seconds for the link to establish
successfully.
• When you unplug the power cord of the
transmitter, the receiver enters standby
mode after 5 minutes.
»The power LED of the receiver lights
up in red.
• The link between the transmitter and
receiver re-established when you plug in
the power cord of the transmitter again.
»The power LED of the receiver ashes
in blue.
LED indicator status of the transmitter
Power LED indicator Status
Solid blue The link is established.
Flashing blue Linking is in progress.
LED indicator status of the receiver
Power
LED
Status
LED
Mode and status
Solid
red
Off Standby mode for power-
saving
Flashing
blue
Flashing Setting up a Link between
the transmitter and
receiver
Solid
blue
Flashing
quickly
On mode but without
input from the computer/
source device
Solid
blue
Flashing
slowly
On mode with
unrecognized video format
Solid
blue
Solid
blue
On mode with recognized
video format
5 Activate your
Philips Wireless
HD Net
Connect and set
up the link
Turn on the power of your
HDTV
HDMI
HDMI
1Go to the source menu under the settings
menu of your HDTV.
2Select the HDMI input to which the
receiver is connected.
Activate the wireless link
Switch on the transmitter and
receiver
When there is power supply for the transmitter
and receiver, they are on automatically.
»The link between the transmitter and
receiver is established.
.
EN
English

10
Note
•If the link is not established after 80 seconds, move the
transmitter, receiver and HDTV closer to each other.
The maximum transmission range is up to 7 meters
without obstruction between the transmitter and
receiver.
•If more than one set of Philips Wireless HD Net
Connect is placed in the same room, make sure that
the minimum distance among each one is 2 meters.
•Make sure the computer is on and switched the signal
output to the HDMI.
•Make sure the video format is supported before the
video is displayed, see the chapter onTechnical data for
information.
On screen display on HDTV
On screen display Mode and status
Standby mode: it is a
power-saving mode
..... Start up in progress: It
takes 15-20 seconds.
x and .... Searching available
channels: It occurs
when the link cannot
establish over
80 seconds after
initialization.
HDMI CH1 On mode with
unrecognized video
format
HDMI CH1 On mode but
without input from
the computer/source
device
HDMI CH1 1080P On mode with
recognized video
format
EN

11
5Hook the key holes at the back of the
receiver on the screws.
6 Mount your
receiver
You can either mount the receiver on the wall
or on the back of the HDTV.
Mount your receiver on the
wall
1Select a spot near the HDTV.
2Drill two holes in the wall. Make sure
that the distance between the two holes
is 45mm and the diameter of the hole is
5 mm.
3Punch the supplied two anchors into the
two holes on the wall.
4Put the two screws into the anchors and
leave 3 mm to mount the receiver on.
EN
English

12
6Align the adhesive tape on the receiver
with the one on the HDTV until both the
receiver and HDTV are mounted together
rmly.
Note
•The use of adhesive tapes is an alternative mounting
option when the receiver cannot be xed.
•When you mount the receiver at the back of the
HDTV, avoid blocking the ventilation holes of the
HDTV.
•For safety reason, check regularly if the HDTV and
receiver are mounted together rmly.
Mount your receiver on the
back of the HDTV
1 Remove the white protective lm from
one of the supplied adhesive tapes.
2Secure the glued side of the adhesive tape
and attach it to the central bottom area of
the receiver.
3 Select a at location on the rear side of
the HDTV.
4 Remove the white protective lm from the
other adhesive tape.
5Secure the glued side of the adhesive tape
and attach it to the selected rear side of
the HDTV.
EN

13
Transmission distance:
Maximum 7 meters without obstruction
between the transmitter and receiver.
Antennas:
High performance internal antennas
Operating frequencies:
5.15 - 5.35 GHz / 5.470 - 5.725 GHz
Power supply:
Input: AC 100~ 240V
Output: DC 5V, 2A
Operating temperature:
0~40°C
Transmitter interfaces
A/V interfaces
HDMI input: One (Type A, Male)
Power interface
Power input:The USB cable connected to the
USB jack of the computer
LEDs
Status LED: 1 x blue LED
Dimensions
30 x 83.3 x 17.5 mm (W x L x H)
Receiver interfaces
A/V interfaces
HDMI output: One (Type A)
Power interface
Power input: 5V DC jack
Switches
Front power switch: One
Info switch: One
LEDs
Power LED: 1 x LED (Two Tone: Blue & Red)
Status LED: 1 x blue LED
Signal quality status: On-screen display
Dimensions
194.8 x 146.8 x 31 mm (W x L x H)
7 Technical data
Supported resolution
Video format timings Resolution
Primary CEA video Timing
480p 640x480p @
59.94/60Hz
480p 720x480p @ 59.94Hz
480p 720x480p @ 60Hz
576p 720x576p @ 50Hz
720p 1280x720p @ 50Hz
720p 1280x720p @
59.94/60Hz
1080i 1920x1080i @ 50Hz
1080i 1920x1080i @
59.94/60Hz
1080p/60 1920x1080p @50Hz
1080p/60 [email protected]/
60Hz
Secondary CEA video Timing
1080p/24 1920x1080p @
23.98/24Hz
1080p/24 1920x1080p @ 25Hz
1080p/24 1920x1080p @
29.97/30Hz
Product specications
General specication
Video resolution
HDMI input: 1080p, 1080i, 720p, 576p, 480p
Supported audio formats:
Digital audio: up to 6 Mbps AC3 and DTS
Analog audio: 32-96 KHz and 16-24 bits per
audio sample
EN
English

14
Compliance with EMF
Koninklijke Philips Electronics N.V. manufactures
and sells many products targeted at consumers,
which, like any electronic apparatus, in
general have the ability to emit and receive
electromagnetic signals.
One of Philips’ leading Business Principles is to
take all necessary health and safety measures
for our products, to comply with all applicable
legal requirements and to stay well within
the EMF standards applicable at the time of
producing the products.
Philips is committed to develop, produce and
market products that cause no adverse health
effects. Philips conrms that if its products are
handled properly for their intended use, they
are safe to use according to scientic evidence
available today.
Philips plays an active role in the development
of international EMF and safety standards,
enabling Philips to anticipate further
developments in standardisation for early
integration in its products.
Environmental-Recycling the
product
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC. Please inform yourself about the local
separate collection system for electrical and
electronic products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste.
Correct disposal of your old product helps to
prevent potential negative consequences for the
environment and human health.
8 Notice
Declaration of conformity
Hereby Philips Consumer Lifestyle, declares
that the SWW1890 is in compliance with
the essential requirements and other relevant
provisions of Directive 1999/5/EC. You can nd
the Declaration of Conformity on www.p4c.
philips.com.
EN 60950-1
Safety of Information Technology Equipment
EN 62311
Assessment of electronic and electrical
equipment related to human exposure
restrictions for electromagnetic elds (0 Hz-300
GHz)
EN 301 893
Broadband Radio Access Networks (BRAN); 5
GHz high performance RLAN; Harmonized EN
covering essential requirements of article 3.2 of
the R&TTE Directive
EN 301 489-1
Electromagnetic compatibility and Radio
Spectrum Matters (ERM); ElectroMagnetic
Compatibility (EMC) standard for radio
equipment and services; Part 1: Common
technical requirements
EN 301 489-17
Electromagnetic compatibility and Radio
spectrum Matters (ERM); ElectroMagnetic
Compatibility (EMC) standard for radio
equipment and services; Part 17: Specic
conditions for 2,4 GHz wideband transmission
systems and 5 GHz high performance RLAN
equipment
Hereby, Philips, declares that this SWW1890 is
in compliance with the essential requirements
and other relevant provisions of Directive
1999/5/EC.
EN

15
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by a
specialized company. Please observe the local
regulations regarding the disposal of packaging
materials and old equipment.
Warranty information
Warranty information can be found at: www.
philips.com/support
EN
English

16
9 Frequently asked questions
The power LED on the
receiver is not lit up in red in
standby mode.
Make sure that there is power supply for the receiver.
There is no video displayed on
my TV screen.
• Make sure that the appropriate cables are selected and
inserted to the transmitter, receiver, and HDTV.
• Make sure that you select HDMI as the input source on your
HDTV.
• Check the power LED and status LED on the receiver:
• Flashing blue power LED: Make sure that the
transmission range between receiver and transmitter
is not over 7 meters transmission distance (with no
obstruction between the transmitter and receiver). Move
the transmitter closer to the receiver.
• Solid blue power LED + slow and ashing source LED:
1) Make sure that the frame rate and video resolution
of your A/V equipment are supported and conformed
to the technical specication (see the chapter ‘Technical
data’). 2) Connect the computer to yourTV with an
HDMI cable to check the compatibility of the video
format.
• Solid blue power LED + quick and ashing source
LED: 1) Make sure that the proper cables are connected
between the receiver and HDTV. 2) Make sure that
your computer connected to the transmitter is powered
on. 3) Make sure that the HDMI cable is connected
between the HDTV and receiver. 4) Make sure that the
display setting of your computer is set to clone display or
extended display.
Tip
•For information about how to set your computer to clone or extended display,
see ‘How can I connect to my computer to enable the external display?’
described later in this chapter.
f the picture quality is poor,
what do I do?
•Make sure that the video scale and resolution of your
computer matches the resolution of your HDTV (See chapter
‘Technical data’).
•Make sure that the transmission range between receiver and
transmitter is not over 7 meters transmission distance (with
no obstruction between the transmitter and receiver).
EN

17
I cannot hear any sound or the
sound is poor, what do I do?
•Make sure that the TV volume is adjusted correctly.
•Make sure that the TV volume is not set to minimum or the
sound is not muted.
•Make sure that the audio volume of your computer is turned
up.
•Make sure that the audio bit rate is supported.
•Make sure that the audio output of your computer is set to
HDMI output.
Tip
•See the chapter ‘Product specication’.
How can I connect to my
computer to enable the
external display?
For Windows7 operation
system: 1Press , then P.
»The screen with options is displayed.
2Select Clone, Extend display or Project out only for external
display.
For Windows Vista operating
system: 1Click on Start > Control Panel > Personalization > Display
settings.
2Make sure that the display 2is on with or without enabling
Extend the desktop onto this monitor.
3Make sure that the resolution is comply to the supported
resolution (See the chapter ‘Technical data’, section supported
resolution).
For Windows XP operating
system: 1On the computer screen, right click on your mouse.
2Select Properties > Settings.
3Make sure that the display 2is on with or without enabling
Extend the desktop onto this monitor.
4Make sure that the resolution is comply to the supported
resolution (See the chapter ‘Technical data’, section supported
resolution).
Tip
•For further information, click on Start > Help and Support, then enter ‘change
display settings’ on the blank space provided.
EN
English

18
For MAC operating system: MAC operating system detects the external display equipment and
switches to a better resolution automatically when you plug in the
display cable to MAC series.
Note
•If the MAC operation system does not detect the external display automatically,
click on > Preference > Detect Displays.
•This product does not work with display port.
How can I change the audio
setting of my computer to
HDMI output?
For Windows7 and Vista
operating system: 1Click on Start > Control Panel > Sound > Playback.
2Set the playback device to the corresponding TV set shown
on the list.
For Windows XP operating
system: 1Click on Start > Control Panel > Sounds and Audio Devices
> Audio > Sound Playback.
2Set the Default device to HDMI device.
Tip
•For further information, click on Start > Help and Support, then enter ‘change
audio settings’ on the blank space provided.
EN

© 2011 Koninklijke Philips Electronics N.V.
All rights reserved.
IFU_SWW1890_EN_V1.3
WK11293
0560