Philips FC6120 User manual

FC6120

2

3
X
W
ADC E
F
G
H
I
U
T
S
V
J
R
Q
P
KLNM O
B
1

4

FC6120
ENGLISH 6
ESPAÑOL 16
한국어 26
PORTUGUÊS DO BRASIL 35
繁體中文 45
简体中文 53
68
76

General description (Fig. 1)
AUpper handle
BHanging slot
CTop part of stick
DMiddle part of stick
EBottom part of stick
FLower handle
GDirt tray door slide
HPivoting hinge
IRoller brush
JTransparent front cover
KSweeper base
LDirt tray
MSocket for small plug
NSmall plug
OAdapter
POn/off button
QCharging light
RDirt tray release button
SRetainer
TBelt
URetainer release slide
VLid of battery pack compartment
WCutting groove
XWheels
Important
Read this user manual carefully before you use the appliance and save it
for future reference.
Check if the voltage indicated on the adapter corresponds to the
local mains voltage before you connect the appliance.
Do not use the appliance if the adapter, the cord or the appliance
itself is damaged. If the adapter is damaged, always have it replaced
with one of the original type in order to avoid a hazard.
-
-
ENGLISH6

This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with
the appliance.
Never use the appliance outdoors. Never use the appliance on wet
surfaces.
Never pick up water, liquids or wet food substances. Never pick up
ammable substances and do not pick up ashes until they are cold.
Never immerse the appliance in water or any other liquid, nor rinse it
under the tap.
Do not use the appliance without the dirt tray or roller brush.
Always switch off the appliance after use, before you charge it and
before you connect or disconnect parts.
Unplug the appliance before you clean or maintain it.
Only charge the appliance with the adapter supplied.
The adapter contains a transformer. Do not cut off the adapter to
replace it with another plug, as this causes a hazardous situation.
The adapter feels warm during charging.This is normal.
Always return the appliance to a service centre authorised by Philips
for examination or repair.
Do not stick your hands/ngers into the rotating roller brush to avoid
injuries.
Electromagnetic elds (EMF)
This Philips appliance complies with all standards regarding
electromagnetic elds (EMF). If handled properly and according to the
instructions in this user manual, the appliance is safe to use based on
scientic evidence available today.
-
-
-
-
-
-
-
-
-
-
-
-
-
ENGLISH 7

Before rst use
1 Pull the handle upwards until it is in upright position. (Fig. 2)
2 Charge the appliance for at least 16-18 hours before you use it for
the rst time (see chapter ‘Charging’).
Preparing for use
1 Connect the upper handle to the top part of the stick.
2 Connect the top part of the stick to the bottom part of the stick
(‘click’). (Fig. 3)
If you want a long stick to suit your height, connect the middle part of the
stick to the bottom and top part of the stick
3 Connect the stick to the lower handle of the sweeper base
(‘click’) (Fig. 4).
To remove the stick, press the button on the lower handle (1) and
pull the stick upwards (2). (Fig. 5)
Charging
Charge the appliance for 16-18 hours.
Only charge the appliance when the battery pack is low to avoid
overcharging.
When the appliance is fully charged, it has an operating time of 25
minutes on hard oors. On carpet, the operating time is shorter due to
higher friction.
1 Switch off the appliance before you charge it.
2 Place the stick in upright position (‘click’) (Fig. 6).
3 Insert the small plug into the socket on the sweeper base (Fig. 7).
4 Insert the adapter into a wall socket.
The charging light is on continuously during charging and after the
battery is fully charged.The charging light goes out when you
disconnect the appliance from the mains.
-
,
ENGLISH8

Using the appliance
1 To unlock the stick from its storage position, put your foot on top
of the sweeper base to prevent it from tilting. Then pull the handle
towards you (‘click’). (Fig. 8)
Do not to put your foot on the on/off button or the dirt tray release
button.
2 Press the on/off button to switch on the appliance. (Fig. 9)
To switch off the appliance, press the on/off button again.
3 To use the sweeper as a handheld appliance, remove the stick and
hold the sweeper by the lower handle. (Fig. 10)
For better grip, push the handle towards the front of the appliance until it
is at a 45-degree angle to the base (‘click’).
Note:The sweeper is not suitable for use on high-pile carpet.
Cleaning
Never clean the appliance or any of its parts in water or in the
dishwasher.
Clean the appliance and its parts with a damp cloth.
1 Always pull the small plug out of the appliance before you clean the
appliance.
2 Clean the appliance with a damp cloth.
Emptying the dirt tray
If you do not empty the dirt tray regularly, dirt will spill out.
1 Always empty the dirt tray after use.
2 Place the stick in upright position (‘click’) (Fig. 6).
3 Press on the dirt tray release button (1) and lift the dirt tray out
of the sweeper base (2) (Fig. 11).
ENGLISH 9

4 Hold the dirt tray over a dustbin.Then press the slide on the lower
handle downwards to open the dirt tray door and empty the dirt
tray (Fig. 12).
5 Place the dirt tray back into the sweeper base and push it down
into position. (Fig. 13)
The dirt tray door closes automatically when you put the dirt tray back
into the sweeper base (‘click’).
Cleaning the roller brush
1 Switch off the appliance before you clean the roller brush.
2 Remove the transparent front cover from the sweeper base. Grab
the bottom edge of the cover with both hands, pull it outwards (1)
and upwards (2) rmly until it is released from the slots (Fig. 14).
3 Rotate the roller brush until the cutting groove faces you. Use a
pair of scissors to cut the hairs, threads etc that have collected
around the roller brush (Fig. 15).
4 Remove uff, hairs and other dirt from the roller brush.
Removing the roller brush
1 To remove the stick, press the button on the lower handle (1) and
pull the stick upwards (2) (Fig. 5).
2 Turn the sweeper base upside down, push the release slide in the
direction of the arrow (1) and remove the retainer (2) (Fig. 16).
3 Slip the belt off the end of the roller brush (1) and lift the brush
out of the base (2) (Fig. 17).
4 Remove uff, hairs and other dirt from the roller brush and the
groove.
Reinserting the roller brush
1 Slip the belt over the ribbed end of the roller brush. Insert the
other end of the roller brush into the slot opposite the
belt (Fig. 18).
ENGLISH10

2 Insert the end of the roller brush with the belt into the other
slot. (Fig. 19)
Do not force the roller brush into the slot. Rotate the roller brush so
that the ridge on the side with the belt points upwards.
3 Put the retainer back into the slot (1) and slide the release slide to
the original position (‘click’) (2) (Fig. 20).
If the roller brush is not properly inserted, you cannot move the release
slide to locked position.
4 Reattach the transparent front cover to the sweeper base. Grab
the cover with both hands, push it downwards (1) and inwards (2)
rmly until it snaps back into the slots (‘click’). (Fig. 21)
Cleaning the wheels
1 Switch off the appliance.
2 Remove the transparent front cover from the sweeper base. Grab
the bottom edge of the cover with both hands, pull it outwards (1)
and upwards (2) rmly until it is released from the slots (Fig. 14).
3 Place the sweeper base upside down.
4 Insert a slotted screwdriver underneath one of the wheels. Rotate
the screwdriver to loosen the axle with the wheel, rings and
spring from the groove (Fig. 22).
Do not place your hand on the wheel.
To prevent the wheel and axle from hitting you or others, do not put
your face close to the sweeper base and do not point it at other
persons.
Note:There are 2 rings and a spring inside each wheel.
5 Repeat steps 4 and 5 to remove the other wheels.
6 Remove uff, hairs and other dirt from the wheels, axles, rings,
springs and grooves.
7 Slide the rings and springs onto the axles. (Fig. 23)
ENGLISH 11

8 Insert the axles into the wheels.
9 Put the axles with the wheels back into the grooves and press
them rmly into position (‘click’). (Fig. 24)
10 Reattach the transparent front cover to the sweeper base. Grab
the cover with both hands, push it downwards (1) and inwards (2)
rmly until it snaps back into the slots (‘click’). (Fig. 21)
Storage
You can store the appliance in three ways:
1 To store the appliance in horizontal position, put the sweeper base
horizontally and the stick upright.
2 To store the appliance in vertical position, tilt the side of the
sweeper base with the roller brush towards the stick (‘click’). Then
park the appliance against a wall (Fig. 25).
3 To hang the appliance from the wall, tilt the side of the sweeper
base with the roller brush towards the stick (‘click’). Then hang the
appliance on a nail by the hanging slot in the back of the upper
handle (Fig. 26).
Environment
Do not throw away the appliance with the normal household waste
at the end of its life, but hand it in at an ofcial collection point for
recycling. By doing this, you help to preserve the
environment (Fig. 27).
If you intend not to use the appliance for a longer period of
time, remove the adapter from the wall socket to save energy.
-
-
ENGLISH12

Battery disposal
NiCd/NiMH batteries can be harmful to the environment and may
explode if exposed to high temperatures or re.
1 Remove the battery pack when you discard the appliance.
Do not throw away the battery pack with the normal household
waste, but hand it in at an ofcial collection point.
You can also take the appliance to a Philips service centre.The staff of
this centre will remove the battery pack for you and will dispose of it
in an environmentally safe way.
Make sure the appliance is switched off and disconnected from the
mains before you remove the battery pack.
Only remove the battery pack if it is completely empty.
2 Let the appliance run until it stops.
3 Undo the screws and remove the lid of the battery
compartment (Fig. 28).
4 Disconnect the terminals one by one and remove the battery
pack (Fig. 29).
Guarantee & service
If you need information or if you have a problem, please visit the Philips
website at www.philips.com or contact the Philips Customer Care
Centre in your country (you nd its phone number in the worldwide
guarantee leaet). If there is no Customer Care Centre in your country,
go to your local Philips dealer or contact the Service Department of
Philips Domestic Appliances and Personal Care BV.
-
-
ENGLISH 13

Troubleshooting
Problem Possible cause Solution
The
appliance
does not
work.
You have not
charged the
appliance.
Charge the appliance (see chapter
‘Charging’).
You have not
inserted the
adapter
properly into
the wall socket.
Insert the adapter properly into the
wall socket.
You have not
inserted the
small plug
properly into
the appliance.
Insert the small plug properly into the
appliance.
The
appliance
does not
pick up dirt
effectively.
The dirt tray is
full. Empty the dirt tray (see chapter ‘Cleaning’).
The roller brush
is clogged. Clean the roller brush (see chapter
‘Cleaning’).
The
appliance
has a short
operating
time.
The battery
pack has
developed a
memory effect.
Discharge the battery pack
completely by letting the appliance
run until it stops.Then recharge the
battery pack for 16-18 hours. Repeat
this discharge-charge cycle 3-5 times.
Dirt
escapes
from the
appliance.
The dirt tray is
full. Empty the dirt tray (see chapter ‘Cleaning’).
ENGLISH14

Problem Possible cause Solution
The dirt tray
door is not
locked properly.
Make sure you put the dirt tray
properly back into the appliance. If the
dirt tray is properly inserted, the dirt
tray door closes automatically (see
chapter ‘Cleaning’).
The
appliance
has no
suction
power.
This is normal.The sweeper does not
have suction power, but is equipped
with a dynamic roller brush
that sweeps dirt into the appliance.
ENGLISH 15

16
Descripción general (g. 1)
AMango superior
BRanura para colgar
CParte superior del tubo
DParte central del tubo
EParte inferior del tubo
FMango inferior
GBotón de la puerta de la bandeja de suciedad
HBisagra pivotante
ICepillo giratorio
JCubierta frontal transparente
KBase de la escoba eléctrica
LBandeja de suciedad
MToma para clavija pequeña
NClavija pequeña
OAdaptador
PBotón de encendido/apagado
QPiloto de carga
RBotón de liberación de la bandeja de suciedad
STope
TCorrea
UBotón de liberación del tope
VTapa del compartimento de la batería
WRanura de corte
XRuedas
Importante
Antes de usar el aparato, lea atentamente este manual del usuario y
consérvelo por si necesitara consultarlo en el futuro.
Antes de enchufar el aparato, compruebe si el voltaje indicado en el
adaptador se corresponde con el voltaje de red local.
No utilice el aparato si el adaptador, el cable o el propio aparato
están dañados. Si el adaptador está dañado, sustitúyalo siempre por
otro del modelo original para evitar situaciones de peligro.
-
-
ESPAÑOL

Este aparato no debe ser usado por personas (adultos o niños) con
su capacidad física, psíquica o sensorial reducida, ni por quienes no
tengan los conocimientos y la experiencia necesarios, a menos que
sean supervisados o instruidos acerca del uso del aparato por una
persona responsable de su seguridad.
Asegúrese de que los niños no jueguen con este aparato.
No utilice nunca el aparato al aire libre ni sobre supercies húmedas.
No recoja nunca agua, líquidos ni sustancias húmedas. No recoja
nunca sustancias inamables, ni tampoco cenizas si no están frías.
No sumerja nunca el aparato en agua u otros líquidos, ni lo enjuague
bajo el grifo.
No utilice el aparato sin la bandeja de suciedad ni sin el cepillo
giratorio.
Apague siempre el aparato después de usarlo, antes de cargarlo y
antes de conectar o desconectar las piezas.
Desenchufe el aparato antes de limpiarlo o de realizar labores de
mantenimiento.
Cargue el aparato únicamente con el adaptador que se suministra.
El adaptador incorpora un transformador. No corte el adaptador
para sustituirlo por otra clavija, ya que podría provocar situaciones de
peligro.
El cargador se notará caliente al tacto durante la carga. Esto es
normal.
Lleve siempre el aparato a un centro de servicio autorizado por
Philips para su comprobación y reparación.
No acerque las manos o los dedos al cepillo giratorio en
funcionamiento para evitar sufrir daños.
Campos electromagnéticos (CEM)
Este aparato Philips cumple todos los estándares sobre campos
electromagnéticos (CEM). Si se utiliza correctamente y de acuerdo con
las instrucciones de este manual, el aparato se puede usar de forma
segura según los conocimientos cientícos disponibles hoy en día.
-
-
-
-
-
-
-
-
-
-
-
-
-
ESPAÑOL 17

Antes de utilizarlo por primera vez
1 Tire del mango hacia arriba hasta que esté en posición
vertical. (g. 2)
2 Antes de usar el aparato por vez primera, cárguelo durante al
menos 16-18 horas (consulte el capítulo “Carga”).
Preparación para su uso
1 Conecte el mango superior a la parte superior del tubo.
2 Conecte la parte superior del tubo a la parte inferior del tubo
(“clic”). (g. 3)
Si desea un tubo más largo para ajustarlo a su altura, conecte la parte
central del tubo con las partes inferior y superior.
3 Conecte el tubo al mango inferior de la base de la escoba eléctrica
(“clic”) (g. 4).
Para quitar el tubo, pulse el botón situado en el mango inferior (1) y
tire del tubo hacia arriba (2). (g. 5)
Carga
Cargue el aparato durante 16-18 horas.
Cargue el aparato únicamente cuando la batería se esté agotando, para
evitar la sobrecarga.
Cuando el aparato esté completamente cargado, proporcionará un
tiempo de funcionamiento de 25 minutos en suelos duros. En alfombras,
el tiempo de funcionamiento es menor debido a la mayor fricción.
1 Apague el aparato antes de cargarlo.
2 Coloque el tubo en posición vertical (“clic”) (g. 6).
3 Inserte la clavija pequeña en la toma de la base de la escoba
eléctrica (g. 7).
4 Enchufe el adaptador a la red.
-
ESPAÑOL18

El piloto de carga permanece encendido durante la carga y una vez
que la batería está completamente cargada. El piloto de carga se
apaga cuando desconecta el aparato de la red.
Uso del aparato
1 Para desbloquear el tubo de la posición de almacenamiento, ponga
el pie sobre la base de la escoba eléctrica para evitar que se incline,
y luego tire del mango hacia usted (“clic”). (g. 8)
No ponga el pie sobre el botón de encendido/apagado ni sobre el
botón de liberación de la bandeja de suciedad.
2 Pulse el botón de encendido/apagado para encender el
aparato. (g. 9)
Para apagar el aparato, vuelva a pulsar el botón de encendido/apagado.
3 Para utilizar la escoba eléctrica como un aparato de mano, quite el
tubo y coja la escoba eléctrica por el mango inferior. (g. 10)
Para agarrarla mejor, empuje el mango hacia la parte frontal del aparato
hasta que forme un ángulo de 45 grados con respecto a la base (“clic”).
Nota: La escoba no es adecuada para uso en alfombras con pelo largo.
Limpieza
No lave nunca el aparato ni ninguna de sus piezas bajo el agua ni en el
lavavajillas.
Limpie el aparato y las piezas con un paño húmedo.
1 Desenchufe siempre la clavija pequeña del aparato antes de
limpiarlo.
2 Limpie el aparato con un paño húmedo.
Vaciado de la bandeja de suciedad
Si no vacía la bandeja de suciedad con regularidad, la suciedad se saldrá
del aparato.
1 Vacíe siempre la bandeja de suciedad después del uso.
,
ESPAÑOL 19

2 Coloque el tubo en posición vertical (“clic”) (g. 6).
3 Pulse el botón de liberación de la bandeja de suciedad (1) y sáquela
de la base de la escoba eléctrica (2) (g. 11).
4 Sujete la bandeja de suciedad sobre un cubo de la basura. Luego
empuje hacia abajo el botón deslizante situado en el mango inferior
para abrir la puerta de la bandeja de suciedad y vacíela (g. 12).
5 Coloque de nuevo la bandeja de suciedad en la base de la escoba
eléctrica y presione hasta que encaje en su sitio. (g. 13)
La puerta de la bandeja de suciedad se cierra de forma automática
cuando coloca de nuevo la bandeja en la base de la escoba eléctrica
(“clic”).
Limpieza del cepillo giratorio
1 Apague el aparato antes de limpiar el cepillo giratorio.
2 Quite la cubierta frontal transparente de la base de la escoba
eléctrica. Agarre el borde inferior de la cubierta con ambas manos,
y tire hacia fuera (1) y hacia arriba (2) rmemente hasta que se
suelte de las ranuras (g. 14).
3 Gire el cepillo giratorio hasta que la ranura de corte quede frente a
usted. Utilice unas tijeras para cortar los pelos, hilos, etc. que hayan
quedado atrapados en el cepillo giratorio (g. 15).
4 Quite las pelusas, pelos y cualquier otro tipo de suciedad del cepillo
giratorio.
Extracción del cepillo giratorio
1 Para quitar el tubo, pulse el botón situado en el mango inferior (1)
y tire del tubo hacia arriba (2) (g. 5).
2 Dé la vuelta a la escoba eléctrica poniéndola boca arriba, deslice el
botón de liberación en la dirección de la echa (1) y quite el tope
(2) (g. 16).
3 Retire la correa del extremo del cepillo giratorio (1) y saque el
cepillo de la base (2) (g. 17).
ESPAÑOL20