Philips HR 8572 User manual

ServiceManual
Philips Domestic Appliances and Personal Care
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
Mobilo Vacuum cleaner
HR 8572
PRODUCT INFORMATION
- Maximum air displacement : 32 I/sec
- Maximum vacuum water column : 240 cm
- Power consumption (IEC) : 1200 W
- Dust storage capacity : 3 l
- Cord length (depends on version) : 6 metre
- Filter system : Paper dustbag
: Motor inlet filter
: Exhaust air filter
- Dimensions cleaner : 44.5 x 29.5 x 25 cm
- Weight cleaner : 5.5 kg
- Colour : red
OPTIONAL
- Exhaust air filter FC 8032 = 4822 015 70056
- Active carbon filter FC 8033 = 4822 480 20145
- Active carbon filter replacem. set FC 8034 = item 12 + 13
- S-class filter FC 8044 = 8838 044 01010
- S-class filter replacement set HR 6994 = item 19 + 20
- Sydney cotton dustbag HR 6997 = 4822 480 10115
- S-closable paper dustbag FC 8021 = 8838 021 00000
- Turbo brush FC 8043 = 4322 004 22960
SERVICE INFORMATION
- To open the appliance, first remove the 2 screws of the control
panel (item 11) then with a big screw driver disconnect the 2
snap locks of panel and lower housing (see drawing).
- Component configuration on exploded view may differ in case
of specific versions. However, the actual components are
distinguished bij means of code numbers.
4322 277 00945
02/06
- If a repair has been made, make sure that all functions of the
appliance are working correctly.
- The spare parts have been standardized as much as possible.
- Item 6, cotton dustbag, is used in those countries where paper
dustbags are not available.
- Item 21 is provided with a long cord-winder spring; both long and
short cords can be used in combination with this spring.
- Cordwinder spring has to be tensioned till maximum minus appox.
1,5 revolution.
- Depending on the original length of the cord, the spare cord must
be shortened.
- If pos. 21 is replaced, shaf Amust be lubricated with silicone
grease (A). This grease may not be used on terminals (25) or on
conductors (24).
- Item 71 up to and including item 85. The assembly of accessories
depends on the national version.
To connect the nozzle, the telescopic
tube and the handle: insert the
narrowed section into the wider section
while turning it a little.
To disconnect: pull while rotating.
To adjust the telescopic tube (item 74)
to the required length, use the knob in
the direction of the arrow while sliding
the top section of the telescopic tube
into or out of the lower section.
- To (dis)assemble the appliance use TORX screw driver no T15
= 4822 395 10329, which is one of a set consisting of T20, T15,
TI0, T9, T8, T7 and T6 = 4822 395 50145.
- Adjusting the PCB on the motor to 220V, 60Hz.
1. Make sure that the potentiometer (item 36) is set at min.
position.
2. Adjust the potentiometer on the PCB item 45, on the motor to
220V/60Hz to allow the motor to run smoothly.
Please note: the standard setting of the spare PCB is 230V/50Hz.
There are open-circuit voltages on all wires.

HR 8572
Pos. Order code Description
1 4322 005 14870 Acc. cover red
2 4822 492 11408 Dust indicator spring
3 4322 009 08700 Dust panel red
4 4822 532 60926 Packing ring
5 4322 003 19220 Front cover red
6 8838 021 00000 S-closable pap. dustbag
4822 480 10115 Sydney cotton dustbag (opt.)
7 4822 256 10354 Dustbag carrier
8 4822 401 11689 Clamp of dustbag carrier
9 4822 466 11497 Dust compartment sealing
10 4322 005 14860 Turn knob red
11 4322 003 19250 Back panel red
12 4822 458 10649 Inletgrill + trio filter
4822 458 10461 Active carbon filter grill (opt.)
13 4822 480 10228 Trio filter
4822 480 20145 Active carbon filter (opt.)
14 4322 003 19260 Pedal red
15 4822 466 62655 Bufferring motor
16 4822 466 11487 Motor disc
17 4322 003 12510 Cord out let
18 4822 441 12341 Lower housing + wheels
19 4822 015 70056 Exhaust air filter
4822 480 10084 S-filter (opt.)
20 4322 009 06910 Air outlet grill
4822 458 10613 S-filter grill (opt.)
21 4322 009 07940 Reel half spring unit (l=9m)
23 4322 001 72360 Brake tyre
24 4322 009 07950 Reel half contact unit
25 4322 009 07960 Contact ring plate
26 4322 006 01440 Cord set Argentina L= 9.3 m
4322 006 01760 Cord set Australia L= 9.3 m
27 4322 006 01680 Cord set Taiwan L= 6.3 m
28 4322 006 01720 Cord set U.K. / H.K. L= 9.3 m
29 4322 006 01410 Cord set Euro 4.8mm pins L= 9.3 m
30 4322 006 01670 Cord set Swiss L= 9.3 m
Pos. Order code Description
31 4322 006 01460 Cord set Italy L= 9.3 m
32 4822 532 12782 Dustbag sealing
33 4822 528 11334 Caster
35 4322 009 06710 Rearwheel (standard)
36 4822 214 12223 Speed control 100-127V
4822 214 12224 Speed control 220-240V
37 4822 479 20197 Cord winder lever
41 4822 276 13205 Push button switch
42 4822 462 10911 Motor cover
43 4822 466 10765 Rear motor buffer
44 4822 402 10109 Suspension bracket
45 4822 214 11359 Motor power PCB 230V-50Hz
4822 214 11911 Motor power PCB 100-127V
46 4822 492 11011 PCB clamp
47 4822 361 10768 Motor 220-240V/50-60Hz
4822 361 10975 Motor 120-127V electr.
4822 361 10913 Motor 100-110V electr.
48 4822 492 11407 Spring switch-knob
71 4822 492 71622 Clip metal tube (opt.)
72 4822 530 10229 Metal tube (opt.)
73 4822 492 71623 Clip telesc. tube
74 4822 530 10233 Telescopic tube
75 4822 530 10382 Bend + hose ass’y
76 4822 530 10235 Bend ass’y
77 4822 479 20195 Crevice nozzle
78 4822 479 60118 Small nozzle
79 4822 479 70072 Big nozzle
80 4822 479 20123 Strip of big nozzle
81 4822 479 30176 Plumeau
A 5322 390 20011 Silicon grease for the shaft
B 4322 002 82550 Screw 3.5 x 12 / T10
This product meets the requirements regard-
ing interference suppression on radio and TV.
After the product has been repaired, it should
function properly and has to meet the safety
requirements as officially laid down at this
moment.
M
MOTOR
POWER
MODULE
ROTARY
POTMETER
CORD WINDER
MAIN
SWITCH

DAP2441
71 73
72 74
76
75
77
78 81
80
79
25
B
24
B
A
21
23
Europe Ø 4.8mm 29
Swiss 30
Italy 31
26
Argentina
Australia
Taiwan 27
28
U.K. / H.K.