Philips FC8261/01 User manual

ServiceManual
Philips Domestic Appliances and Personal Care
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
Vacuum cleaner
FC8261/01
07/10
PRODUCT INFORMATION
- This product meets the requirements regarding
interference suppression on radio and TV.
- After the product has been repaired, it should function
properly and has to meet the safety requirements as
officially laid down at this moment.
TECHNICAL INFORMATION
- Colour : Grenadine Red
- Power consumption : 1400 W
(IEC) 230V
- Maximum Air displacement : 32 l/s
- Dust storage capacity : 1 L
- Cord length : 5 m
(depending on type)
- Filter system : Pleated cyclone-filtration
system
: HEPA Exhaust filter
- Noise : 85 dB
- Electronic motor speed control
ACCESSORIES
- Nozzle : All purpose floor nozzle
- Tubes : Conical chrome tubes
- Accessories : Crevice nozzle, Brush and Small nozzle
- Coupling : Conical coupling
OPTIONAL (accessories)
- FC8028 Pleated Filter cylinder 8838 028 01010
- FC8029 HEPA Exhaust filter 8838 029 01010
- Filter cleaning brush 4322 004 20130

FC8261/01
DISASSEMBLY- AND RE-ASSEMBLY ADVISE
- First remove the dust bag.
- Remove the dustcover using a screwdriver (see picture).
- When the dustcover has been removed, the 5 screws Athat
need to be unscrewed to disassemble the upper housing, are
accessible.
A
A
A
A
A
- After removing screw B, lift the motor cap (item 20) out of
the lower housing to be able to take out the cord winder
unit.
B
- To disassemble the cord winder, use TORX screwdriver
no. T10, which is one of a set consisting of T20; T15; T10;
T9; T8; T7 and T6 (code number 4822 395 50145).
- During re-assembling, take care the wires are positioned in
the guides correctly.
REPAIR INSTRUCTION
- The spare parts have been standardized as much as possible.
- Depending on the original cord, the spare cord must be
shortened to the length of the original cord.
- The cord winder spring must be tensioned to the maximum
level and then be rewound approx. 1.5 turn
- If the reel half spring unit is replaced, shaft Dmust be
lubricated with silicone grease. Do not apply any silicone
grease to or spill any grease on terminals (item 34) or
conductors (item 33).
- Item 7, air valve, opens to cool the motor if the air
displacement is too low or if the airflow is blocked.
ELECTRICAL DIAGRAM
M
SPEED
CONTROL UNIT
CORD WINDER
C
2-6

FC8261/01
PARTS LIST
3-6
Pos Service code Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
4322 009 09750
4322 003 29290
4322 001 73680
4322 003 29030
4322 005 20850
4322 005 20840
4322 005 19070
4322 003 28510
4322 001 73610
4322 003 28480
4322 005 20760
4322 003 28730
4322 003 28720
4322 003 28710
4322 000 68060
4322 003 28570
4322 003 28580
4322 003 28700
4322 006 23290
4322 003 28560
4322 005 20820
4322 003 28670
4322 001 73640
4322 003 28690
4322 005 21440
Dustcover Assy Grenadine Red
Container cover Grenadine Red
Sealing ring
Filter case Spectra Yellow *
Filter Spectra Yellow *
Dustbucket Spectra Yellow *
Valve assy
Side panel
Dustcover seal
Nose piece
Caster assy
Slide Artic Ice
Buttons-E Artic Ice
Actuator
Button spring
Back panel Dark raven
Switch cap
Drive wheel
PCB electronic control
Motor cap
HEPA filter Gemini
Air outlet cover HEPA
Cooling hose
Knee bend cooling tube
Lower housing assy
Pos Service code Description
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
4322 001 73590
4322 003 28680
4322 006 98040
4322 006 97970
4322 006 98000
4322 003 28550
4322 001 73580
4322 005 20770
4322 009 07610
4322 009 09060
4341 005 01330
4341 005 00790
4341 006 01890
4322 006 02160
4322 006 02060
4322 006 02080
4322 006 07600
4341 004 20420
4341 005 01240
4322 004 23750
4341 004 20170
4341 004 20100
4341 004 20190
4322 004 23520
4822 479 20039
4822 479 20038
Motor buffer front
Motor front support Domus
Motor Domus 240 V 1400 W
Motor Domus 230 V 1400 W
Motor Domus 220 V 1400 W (ccc)
Air guide Domus
Bufferback Gemini
Base plate assy Gemini
Real half spring unit
Real half spring unit PRC
Real half contact side
Contact plate assy
Cordset Taiwan/PRC L = 5.3 m
Cordset U.K./H.K. L = 6.3 m
Cordset Europe L = 6.3 m
Cordset Swiss L = 6.3 m
Cordset Brazil L = 7.3 m
Bend/hose assy
Bend handle
Chrome tube con. (1pcs)
Crevice nozzle con.
Small nozzle con.
Brush con.
Nozzle D272
Nozzle brush
Nozzle strip
* Standardized colour

FC8261/01
EXPLODED VIEW
1
9
10
2
3
4
6
11
25
8
7
5
13
12
15
16
20
21
14
22
18
19
17
23
24
4-6

FC8261/01
EXPLODED VIEW
3029282726
32
34
35÷39
33
D
C
C
31
5-6

FC8261/01
EXPLODED VIEW
Taiwan / P.R.C. 35 Korea / Europe 37
Swiss 38
Brazil 39
36H.K. / U.K.
46
47
48
45
40
41
43
44
42
6-6