Philips FC8424 User manual

ServiceManual
Philips Domestic Appliances and Personal Care
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
City Line Venice Vacuum cleaner
FC8424
/02
/A
03/06
PRODUCT INFORMATION
- Colour: Vanilla cream
- Electronically controlled motor speed
- Built-in cord winder
- Dustbag-full indicator in dust cover
- This product meets the requirements regarding
interference suppression on radio and TV.
- After the product has been repaired, it should function
properly and has to meet the safety requirements as
officially laid down at this moment.
TECHNICAL INFORMATION
- Maximum air displacement : 34 l/sec.
- Maximum vacuum water column : 260 cm
- Power consumption (IEC) 225V : 1500 W
- Dust storage capacity : 2 l
- Cord length (depends on version) : 6 m
- Filter system : 5 filters
- Dimensions of cleaner : 382 x 292 x 218 mm
- Dimensions of packaging : 510 x 305 x 330 mm
- Net weight : 4.5 Kg
- Gross weight : 8,0 Kg
- Noise : 79 dB
OPTIONAL (accessories)
- FC8021 S-paper dustbags 8838 021 00000
- FC8032 Exhaust AFS micro filter 4822 015 70056
- HR6997 Sydney cotton dustbag 8836 997 01010
DISASSEMBLY- AND RE-ASSEMBLY ADVISE
- First lift and remove the knob and printed knob base and
then loosen mounting screws A.
AA
A
- Lift the motor housing (item 26) out of the lower housing
and take out the cord winder unit.
- To disassemble the cord winder, use TORX screwdriver no.
T10, which is one of a set consisting of T20; T15; T10;
T9; T8; T7 and T6 (code number 4822 395 50145).

FC8424/02/A
REPAIR INSTRUCTION
- The spare parts have been standardized as much as possible.
- Cotton dustbags are used in countries where paper dustbags
are unobtainable.
- If the reel half spring unit is replaced, shaft Fmust be
lubricated with silicone grease. Do not apply any silicone
grease to or spill any grease on terminals (36) or conductors
(35).
- Item 34 is provided with a long cord-winder spring, but
both long and short cords can be used in combination with
this spring. (L = 9.3 m)
- Depending on the length of the original cord, the spare
cord may have to be shortened.
- The cord winder spring must be tensioned to the maximum
level and then be rewound approx. 1.5 turn
- The RPM can be adjusted by means of the potentiometer
mounted on the PCB (item 25). The RPM is correctly
adjusted if the motor starts automatically and continues to
run smoothly with the ON/OFF position and the
adjustable potentiometer in minimum position.
- If the function of the electronic control unit (item 25) is
not required, the Triac must be short-circuited in the
manner shown in the circuit diagram.
- When the vacuum cleaner is used to suck up fine dust, the
pores of the dustbag may become clogged, causing the
passage of air through the dustbag to become obstructed.
As a result, the dustbag-full indicator will indicate that the
dustbag needs to be replaced, even though the dustbag is
not full at all.
ELECTRICAL DIAGRAM
M
MOTOR
POWER
MODULE
Brown
Blue
CORD WINDER
Black
Black
Triac
Short-circuit
2-6

FC8424/02/A
PARTS LIST
3-6
Pos Service code Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
4341 009 00670
4341 009 00720
8838 021 00000
4822 480 10115
4341 009 00760
4341 001 70180
4341 009 00800
4341 001 70190
4341 003 02180
4341 009 00790
4322 003 12220
4822 480 40234
4341 009 00770
4341 009 00780
4341 005 00780
4341 005 01360
4341 003 02280
4341 009 00810
4341 003 02310
4341 003 02250
4822 015 70056
4341 003 02240
4341 003 02330
4341 003 02390
4322 006 50600
4341 006 20560
4341 006 20570
4341 003 02320
4341 001 70210
handle Vanilla cream
dust cover Vanilla cream
S-bag set
cotton dustbag (opt.)
dustbag frame
dust cover sealing
lowerhousing assy
inlet rubber
nose piece
rear wheel standard (opt.)
wheel bush
safety filter
caster assy
cover and filter
turn knob grip stand (opt.)
knob base
cord outlet
upper housing
pedal
AFS back grille
AFS filter
wheel peg
cooling tube
switch lever
switch soldered
PCB ANS EL 220 - 240 V
PCB ANS EL 120 V
motor cap
buffer back
Pos Service code Description
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
46
47
48
49
50
51
52
53
54
55
4322 009 06430
4322 009 06770
4822 466 62655
4341 003 02360
4322 003 06620
4322 001 72360
4322 009 07640
4322 009 07610
4322 009 09060
4341 005 01330
4341 005 00790
4322 006 01770
4341 006 01890
4322 006 02100
4322 006 02060
4322 006 02080
4322 003 17380
4341 004 20450
4322 002 22610
4322 004 22990
4341 003 02470
4341 004 20170
4341 004 20100
4341 004 20190
4322 004 22940
4322 004 22330
4322 005 11040
8838 041 01010
motor ANS 1451 230 V
motor ANS 1241 EL 120 V
buffer ring front
ANS motor disc
push rod
brake tyre
base plate assy
reel half spring unit
reel half spring unit PRC
reel half contact side
contact plate assy
flat cord set Japan/Taiwan 5.3 m
cordset 1.0 / 5.3 m PRC / R
flat cord set U.K./H.K. 6.3 m
flat cord set Euro/Korea 6.3 m
flat cord set Swiss
bend con.
bend and hose assy
metal tube con. (opt.)
telesc.tube con.
accessory clip
crevice nozzle con.
small nozzle con.
dusting brush con. (opt.)
big nozzle con.
twist & clean nozzle con. (opt.)
polishing disc (opt.)
pads for twist & clean nozzle (opt.)

FC8424/02/A
EXPLODED VIEW
A
D
A
A
B
D
C
C
B
14
15
16
17
18
19
20
9
13
3
1
7
8
2
4
5
6
911
10
21
12
4-6

FC8424/02/A
EXPLODED VIEW
E
E
E
E
31
32
33
34
36
37÷40
26
28
29
30
35
27
25
23
24
22
FG
G
5-6

FC8424/02/A
EXPLODED VIEW
52
48
49
50
46
51
54
55
53
47
42
41
Taiwan / P.R.C. 37 Korea / Europe 39
Swiss 4038H.K. / U.K.
6-6