Philips FC9261 User manual

ServiceManual
Philips Consumer Lifestyle
Published by Philips Consumer Lifestyle Printed in the Netherlands © Copyright reserved Subject to modification
Vacuum cleaner
FC9261
11/03
PRODUCT INFORMATION
- This product meets the requirements regarding
interference suppression on radio and TV
- After the product has been repaired, it should function
properly and has to meet the safety requirements as
officially laid down at this moment
TECHNICAL INFORMATION
- Colour : Bordeaux red
- Power consumption : 2000 W (IEC) 230 V
- Maximum Air displacement : 37 l/s
- Vacuum : 27.5 kPa
- Duststorage capacity : 1.5 L
- Cord length : 9 m
- Motor : Infrared remote controlled
- Fiter system : HEPA cyclone-filtration
auto-clean system
: Permanent motor
protection filter
: Ultra Clean Air HEPA13
washable exhaust filter
- Dimensions of cleaner : 485 x 285 x 335 mm
- Net weight : 9.6 kg
ACCESSORIES
- Nozzle : All purpose nozzle
- Additional nozzle : Hard floor nozzle
- Tubes : Metal lacquered telescopic tube
- Handgrip : Ergonomic handgrip with remote
control
- Accessories : Brush, crevice nozzle and small nozzle
- Accessory storage : Active accessory storage bridge in
handgrip
- Coupling : Button coupling
OPTIONAL (accessories)
- FC 8031 : Super Clean Air HEPA filter
- FC 8038 : Super Clean Air HEPA washable filter

FC9261
DISASSEMBLY- AND RE-ASSEMBLY ADVISE
- To open the appliance, first remove the filter cover
(item 39).
- Remove the can with the filters.
- Then remove the hingecover (2 screws A)
- When the hinge cover is removed, the dustcover can be
removed.
- Now remove the drive coupling (item 13) by turning it
clockwise.
- To remove the housing (9 screws F), for some screws you
will require a screwdriver with 14.5 cm long shrank.
Screwdriver 4322 009 08490 for T15 can be used.
- When the repair is finished, check whether all functions of
the appliance work properly.
- To disassemble the cord winder, use TORX screwdriver no.
T10, which is one of a set consisting of T20; T15; T10; T9;
T8; T7 and T6 (code number 4822 395 50145)
ELECTRICAL DIAGRAM
REPAIR INSTRUCTION
- Due to precisely pre-adjusted belt-tension, rattle drive unit
(item 12) may only be replaced as a complete unit.
Do not disassemble this unit in any way!
- If the reel half spring unit is replaced, shaft (M) must be
lubricated with silicone grease. Do not apply any silicone
grease to or spill any grease on terminals (item 55) or
conductors (item 56).
- The cord winder spring must be tensioned to the maximum
level and the be rewound approx 1.5 turn.
- Item 15, air valve, opens to cool the motor if the air
displacement is too low or if the airflow is blocked.
RATTLE
DRIVE
MOTOR
Black
BlackBlack
Blue
Brown
Red
Blue
IR PCB
Switch
CORD
WINDER
M
M
IR
TRANSMITTER
2-8

FC9261
- Appliances from before WK845 have a potential problem
in the cord winder system; the lever of spindle (Pos. 26) can
move out of position.
Symptom:
Cord will not rewind pressing the cord winder button.
Solution:
Remove the Cord winder button as shown in below picture:
Remove the cord winder button by simultaneously operating
the button and putting a screwdriver between the openings
that occur.
Then lift the button by levering the screwdriver.
This has to be done at 2 (two) positions as indicated in the
picture.
Insert a screwdriver (size 1) in the position as shown in below
picture and move it backwards until a “Click” is heard, the
lever of spindle is now back in position. This can be tested by
pressing lever A, the cord should rewind now.
A
“Click”
REPAIR INSTRUCTION
To prevent lever shifting out of position to re-occur,
CW support (Pos. 71) must be added as shown in below
pictures:
Rotate the part 90 degrees CCW, once it is inside the housing
half way.
90°
90°
CCW
CCW
90°
CCW
Then drop the part till it is completely inside the appliance
and push down with a screwdriver untill “Click”.
“Click”
“Click”
“Click”
Finally re-assemble the button.
Press it firmly, until the “Click”.
3-8

FC9261
PARTS LIST
4-8
Pos Service code Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
4322 005 25400
4322 003 34210
4322 003 34200
4322 003 34180
4322 005 25480
4322 003 34160
4322 000 68230
4322 003 34230
4322 001 73910
4322 003 34220
4322 003 35180
4322 005 23140
4322 005 19600
4322 003 35210
4322 005 26540
4322 009 09860
4322 003 32920
4322 005 25420
4322 004 20130
4322 005 24220
4322 003 34140
4322 005 27210
4322 005 27470
4322 006 23530
4322 001 74100
4322 003 31310
4322 003 34070
4322 003 34060
4322 005 25470
4322 000 39120
4322 003 32890
4322 003 32900
4322 003 34150
4322 005 27220
4322 003 34110
Handle assy
Handle side rear
Handle side front
Handle support
Dustcover toppanel
Dustcover Bordeaux red
Spring
Dustc. lock button Bordeaux red
Dustcover sealing
Dustc. inside incl. seal. Bord. red
Choke valve cover Bordeaux red
Rattle drive unit assy
Coupling assy
Hinge cover Bordeaux red
Choke valve assy
Rattle filter cyl. assy Bord. red
Tower assy
Bucket assy Transp. Aqua
Filter Brush
Upperh. sidec. assy Transp. Aqua
Bumper right Bordeaux red
Cordwinder button Bordeaux red
RMC window assy
PCB assy incl. IR
Cooling tube
Lever of spindle
Front handle Bordeaux red
Lower housing Bordeaux red
Caster wheel assy Bordeaux red
Motor inlet filter
Inlet sealing 2
Switch lever
Bumper left Bordeaux red
On/Off button Bordeaux red
Backpanel Bordeaux red
Pos Service code Description
36
37
38*
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
4322 006 07750
4322 003 34100
4322 005 27781
4322 005 23940
4322 004 93350
4322 000 38960
4322 000 39020
4322 003 31220
4322 000 39000
4322 000 39010
4322 003 25390
4322 003 31240
4322 001 73440
4322 009 09430
4322 000 39110
4322 003 26030
4322 001 73520
4322 003 31250
4322 005 18670
4322 005 17430
4322 005 17910
4322 006 07410
4322 006 07390
4322 006 07400
4322 005 25770
4322 009 09930
4322 005 27430
4322 009 09940
4322 005 25790
4322 003 34660
4322 005 25800
4322 004 20580
4322 005 27340
4322 004 23820
4322 004 23770
4322 003 35650
Switch
Cord outlet Bordeaux red
Skate wheel assy Left & Right
Exhaust grille assy Autumn Grey
HEPA13 filter washable
Exhaust sealing
Silencer 4
S-class H sealing
Silencer 1 wall
Silencer 2 bottom
Inlet sealing 1
Motorhousing top
Motorbuffer front
Motor 1761 220 - 240 V
Silencer 3 VCM
Motor bracket
Bufferback green
Motorhousing bottom
Reelhalf spring unit
Reelhalf cordside assy
Contactplate assy
Cordset UK/HK 9.3 m
Cordset Euro 4.8 mm 9.3 m
Cordset Swiss 9.3 m
Battery lid assy
Bend type 1 assy
Hose/connection assy Bord. red
Hose/connection/bend
type 1 assy Bordeaux red
Accessoiry holder
Crevice nozzle
Small nozzle
Brush tool
2pc Telescopic tube assy
RD264 Nozzle stand.
Hard floor nozzle
CW Support
* Standardized colour
= changed

FC9261
EXPLODED VIEW
F
F
F
D
4x
F
F
F
F
F
F
A
A
B
3x
E
2x
C
2x
Blue
U
T
Red
6
13
7
3
5
12
9
8
10
11
14
15
19
18
17
16
20
1
4
2
5-8

FC9261
EXPLODED VIEW
G
8x
H
H
H
H
Black Black
YW
Red
Brown
Black
Blue
Black
Blue
U
T
VW
ZX
40
39
41
34
33
7
32
31
30
37
38
36
35
42
43
44
45
26
28
25
24
29
7
71
21
22
23
27
38
6-8

FC9261
EXPLODED VIEW
J
J
J
56
54
55
L
K
L
L
M
Blue
Brown
Z
V
57 59
÷
50
53
52
49
51
47
46
48
Black
Black
XY
7-8

FC9261
EXPLODED VIEW
Europe Ø 4.8mm 58
Swiss
57U.K. / H.K. 59
66
64
68
67
65
69
60
61 62
63
70
8-8