Philips HR 8569 User manual

ServiceManual
Philips Domestic Appliances and Personal Care
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
Mobilo Vacuum cleaner
HR 8569
PRODUCT INFORMATION
- Maximum air displacement : 37 l/sec.
- Maximum vacuum water column : 310 cm
- Power consumption (IEC) : 1400 W
- Dust storage capacity : 3 litres
- Cord length : 6.3 metres
- Filter system : Paper dustbag
: Motor inlet filter
: Exhaust air filter
- Dimensions cleaner : 44.5 x 29.5 x 25 cm
- Weight cleaner : 5.5 kg
- Colour cleaner : Green
- Noise : 77 dB
OPTIONAL
Exhaust air filter HR 6932 (8836 932 01210)
Active carbon filter HR 6949 (8836 949 01010)
Active carbon filter replacem. set HR 6968 (items 12 + 13)
S-class filter HR 6992 (8836 992 01010)
S-class filter replacement set HR 6994 (items 19 + 20)
Sydney cotton dustbag HR 6997 (8836 997 01010)
Sydney closable pap. dustbag HR 6999 (8836 999 01010)
Sydney 3-M dustbag HR 6999 (8836 999 90010)
4322 277 00259
00/03
PCS 101 398
SERVICE INFORMATION
- To open the appliance, first
remove the 2 screws of the
control panel (item 11) then
with a big screw driver dis-
connect the 2 snap locks
of panel and lower housing
(see drawing).
- Component configuration on exploded view may differ in case
of specific versions. However, the actual components are distin-
guished bij means of code numbers.
- The spare parts have been standardized as much as possible.
- Item 6, cotton dustbag, is used in those countries where paper
dustbags are not available.
- Item 21 is provided with a long cord-winder spring; both long and
short cords can be used in combination with this spring.
- Cordwinder spring has to be tensioned till maximum minus approx.
1,5 revolution.
- Depending on the original length of the cord, the spare cord must
be shortened.
- To (dis)assemble the appliance use TORX screw driver no T15
= 4822 395 10329, which is one of a set consisting of T20, T15,
TI0, T9, T8, T7 and T6 = 4822 395 50145.
- Adjusting the PCB on the motor to 220V, 60Hz.
1. Make sure that the potentiometer (item 36) is set at min.
position.
2. Adjust the potentiometer on the PCB item 45, on the motor to
220V/60Hz to allow the motor to run smoothly.
Please note: the standard setting of the spare PCB is
230V/50Hz.
There are open-circuit voltages on all wires.
This product meets the requirements regard-
ing interference suppression on radio and TV.
After the product has been repaired, it should
function properly and has to meet the safety
requirements as officially laid down at this
moment.
!Service
Information

PCS 101 399
Pos. 12 nc description
1 4322 003 16870 acc. cover
2 4322 000 67680 dust indicator spring
3 4322 009 07390 dust cover green
4 4322 001 94690 packing ring
5 4322 003 16900 front cover
6 8836 999 01010 Sydney closable pap. dustbags
8836 999 90010 Sydney 3M dustbag (opt.)
8836 997 01010 Sydney cotton dustbag (opt.)
7 4322 009 06760 dustbag carrier
8 4322 003 12280 clamp of dustbag carrier
9 4322 003 12020 dust compartment sealing
10 4322 005 11480 turn knob
11 4322 003 16930 back panel
12 4322 009 07040 inletgrill + trio filter
4322 003 10950 active carbon filter grill (opt.)
13 4322 000 37300 trio filter
8836 949 01010 active carbon filter (opt.)
14 4322 005 11490 pedal
15 4322 001 72780 buffering motor
16 4322 003 12080 motor disc
17 4322 003 16770 cord outlet
18 4322 009 07400 lower housing + wheels
19 8836 992 01010 S-class filter (opt.)
8836 932 01210 AFS micro filter
20 4322 005 08660 grill S-class filter (opt.)
4322 003 16950 grill AFS micro filter
21 4322 009 05350 reel half spring unit
23 4322 001 72360 brake tyre
24 4322 009 04800 reel half contact unit
25 4322 009 05060 contact ring plate
26 4322 007 11960 cord Australia l = 6.3 m
27 4322 007 12150 cord Japan / low voltage
28 4322 007 12190 cord UK l = 6.3 m
29 4322 007 11930 cord Europe 4.8 mm l = 6.3 m
4322 007 11920 cord Europe 4.8 mm l = 8.5 m (opt.)
Pos. 12 nc description
30 4322 007 12020 cord Swiss l = 6.3m
4322 006 01280 cord Swiss l = 8.5m (opt.)
31 4322 007 11950 cord Italy l = 6.3 m
32 4322 003 12240 dustbag sealing
33 4322 005 10760 caster assy standard
35 4322 009 07420 rear wheel + cover
36 4322 006 07220 speed control 220 - 240 V
37 4322 003 12030 cord winder lever
41 4322 006 50580 push button switch
42 4322 003 12010 motor cover
43 4322 001 72790 rear motor buffer
44 4322 003 09720 suspension bracket
45 4322 006 20720 motor print 230 V - 50 Hz
46 4322 000 03700 PCB clamp
47 4322 009 06430 motor 220-240 V / 50-60 Hz
48 4322 000 09750 spring switch knob
74 4322 007 16000 leafspring
75 4322 005 08310 bend and hose
76 4322 003 16020 bend
77 4322 003 16010 crevice nozzle 118 mm
78 4322 004 00650 small nozzle
81 4322 004 00590 plumeau
103 4322 009 05410 tube clip assy 35 mm
104 4322 004 22180 telescopic tube + clamp
105 4322 004 22120 nozzle RD 262 active coupling
111 4322 004 22330 polishing nozzle HR 8040
112 4322 005 11040 polishing disc
113 8838 041 01010 polishing brushes HR 8041
121 4322 001 99120 coupling bush
122 4322 007 45550 coupling spring
DFU 4222 000 47250 direction for use
M
MOTOR
POWER
MODULE
ROTARY
POTMETER
CORD WINDER
MAIN
SWITCH

3
4
8
6
333221÷31
12 13
9
7
5
CLICK
2
1

PCS 101 400
35
19 20
17
12 13
48
10
16
15
43
47
46
45
44
42
41
37
36
11
14
CLICK
DAP1123
18

PCS 101 401
25
B
24
B
21
EUROPE Ø4.8mm 29
CH 30
ITALY 31
23
26
AUSTRALIA
FLAT PINS 27
28
GB
DAP1161
74
75
77
78
81
76
105
104
121
122
103
112
111
113