Phillips Connect EZTrac Plus User manual

Page 4 PCT-EZTPIG REV0_8-21-19
PHILLIPS CONNECT TECHNOLOGIES
12012 BURKE STREET, SANTA FE SPRINGS, CA 90670
TEL: [phone]
WWW.PHILLIPS-CONNECT.COM
PHILLIPS CONNECT TECHNOLOGIES
TRANSPORTATION TECHNOLOGIES REIMAGINED
Customer Care: 833-213-5839
UI: pct.phillips-connect.com
LIMITED PRODUCT WARRANTY - Company hereby warrants (“Limited Warranty”) only to the purchaser that first activates the Product, that the
Product will be free from defects in workmanship and materials for a period (“Limited Warranty Period”) of one (1) calendar year after the date that
the product reports to the PCT server. The Limited Warranty does not apply to normal wear and tear and does not cover repair or replacement if the
Product is damaged by tampering, misuse, accident, abuse, neglect, improper installation, misapplication, alteration of any kind, disaster, defects due
to repairs or modifications made by anyone other than Company or an authorized service representative of Company, or reception problems caused
by signal conditions or cable or antenna systems outside the Product. Further, the Limited Warranty does not apply to physical damage of any nature
whatsoever to the Product, including any opening or attempted opening of the Product, and any such opening or attempted opening of the Product
shall render the Limited Warranty invalid. REPAIR OR REPLACEMENT OF A DEFECTIVE PRODUCT IS YOUR SOLE AND EXCLUSIVE REMEDY UNDER
THE LIMITED WARRANTY. SOFTWARE LOADED ON THE PRODUCT IS PROVIDED “AS IS” WITHOUT WARRANTY. COMPANY SHALL NOT BE LIABLE
FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES FOR BREACH OF THE LIMITED WARRANTY. TO
THE MAXIMUM EXTENT PERMITTED BY LAW, COMPANY EXPRESSLY DISCLAIMS, AND YOU EXPRESSLY WAIVE, ALL OTHER WARRANTIES, WHETHER
EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING WITHOUT LIMITATION ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PAR-
TICULAR PURPOSE OR USE, OR ANY WARRANTY ARISING OUT OF ANY PROPOSAL, SPECIFICATION, OR SAMPLE. THE TERM OF ANY IMPLIED
WARRANTIES THAT CANNOT BE DISCLAIMED UNDER APPLICABLE LAW SHALL BE LIMITED TO THE DURATION OF THE FOREGOING EXPRESS
WARRANTY PERIOD. SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES AND/OR DO NOT ALLOW LIMITATIONS ON THE
AMOUNT OF TIME AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. You agree that neither Company nor any other
party has made any representations or warranties, nor have you relied on any representations or warranties, express or implied, including any implied
warranty of merchantability or fitness for any particular purpose with respect to the Products. You acknowledge that no affirmation of fact or statement
(whether written or oral) made by Company, its representatives, or any other party outside of this Agreement with respect to the Products shall be
deemed to create any express or implied warranty on the part of Company or its representatives. To obtain warranty service Contact the Customer
Service Department using the support number located on the website you were provided when you purchased the product. Provide them with the IMEI
(International Mobile Equipment Identity) for each product for warranty coverage verification. Upon verification of coverage, an RA# will be issued
and provided to you by email, or over the phone. Package product(s) and send to Company with the RA# clearly written on the outside of each pack-
age (returns without an RA# will be rejected) and ship to: PCT Returns at the address provided to you. Note: You are responsible for shipping charges
to the returns department.) Company will test all properly returned products to determine if they are defective. If the product is defective Company will
provide replacement of the defective product(s) and Company is responsible for shipping charges back to you. If the product is not defective, then you
will be charged $49.95 to cover the cost of testing the product and you are responsible for the shipping charges back to you.
Now that you’ve purchased your EZTrac™ Plus and successfully installed your hardware on your
trailer or chassis, you are ready for the next step!
1. Navigate to the app store on your smart device (Apple or Android) and search for Phillips Connect. Once you find the app,
start the download process.
2. After you have the app on your smart device, open it and scan the IMEI barcode on your EZTrac™ Plus device. You will
then be prompted to fill out your email information.
3. Next, you will need to fill out some account information about your Asset and Company name. This will create a shell account
on the web portal.
4. Navigate to your email and you will see an email from Phillips Connect Technologies. Open the email and click the link to
validate your email address.
5. Once your email has been validated, you will be directed to the login page on the Web Portal.
a. Accept EULA, SLA, and Warranty to proceed
6. Now, you will need to create your Web Portal account. You will need to add your first and last name, phone number,
username (email), create a password, and select the appropriate time zone.
7. After you’ve logged in, you will then select a subscription for the IMEI(s) that you have purchased and input your
payment information.
8. Once your credit card information is entered and processed you will have immediate visibility to all your installed assets
on the User Interface
9. Confirm the EZTrac has powered up and shows the current location on the map before assigning the trailer or chassis ID.
Page 1
PHILLIPS CONNECT TECHNOLOGIES
TRANSPORTATION TECHNOLOGIES REIMAGINED
PCT-EZTPIG REV0_8-21-19
PHILLIPS CONNECT TECHNOLOGIES
12012 BURKE STREET, SANTA FE SPRINGS, CA 90670
TEL: [phone]
WWW.PHILLIPS-CONNECT.COM
EZTrac™ Plus Installation Guide
EZTrac™ Plus is installed in the trailer or chassis bogie area.
Rear of Crossmember
IMPORTANT: If the unit has a sliding tandem, install on the rear of a
crossmember in the sliding tandem
EZTrac™ Plus
Gateway Four (4) Cable Ties
Kit Includes:
ABS Extension
Harness SCAN FOR MORE
INFORMATION
Power Extension
Harness
Side Cutters
T 15
T 15
Cordless Drill
11/32” Deep
Socket
3/16”
Drill Bit
1-T-15
Torx Drive
Tape
Measure
Side Cutter
Tool List:
4-Wire Ties
Two (2) 18-8 Stainless
Steel Serrated Flange
Locknut, 8-32 Thread
Size
Two (2) Stainless
Steel Buttonhead Torx
Screws, 8-32 Thread
Size, 1 1/4” Long
1
2
3

Page 2 PCT-EZTPIG REV0_8-21-19
2-Buttonhead Torx Screws
Stainless Steel, 8-32 Thread Size, 1”Long
2- 18-8 Stainless Steel Serrated
Flange Locknut 8-32 Thread Size
Channel Cut
Away For Clarity
2
FRONT
Use Gateway As A Template
Making Sure The Gate Is 2” From
The Drivers Side Frame Rail
Use A 3/16 Drill Bit
Channel Cut Away For Clarity
Gateway
Mount Gateway 2” From Curb Side Rail
1
2
3
FRONT
PHILLIPS CONNECT TECHNOLOGIES
12012 BURKE STREET, SANTA FE SPRINGS, CA 90670
TEL: [phone]
WWW.PHILLIPS-CONNECT.COM
Mounting and Connecting the EZTrac™ Plus Gateway Device
Gateway
Channel Cut Away
for Clarity
Mount Gateway
at least 2” From
Curb Side Frame
Rail
1. Mount at least 2 inches from the frame
rail so the EZTrac™ Plus Gateway has a clear
view to the ground.
Use a 3/16” Drill Bit
Channel Cut
Away for Clarity
Use EZTrac™ Plus Gateway as a Tem-
plate, Making Sure the Gateway is
at least 2” from the Curb Side Frame
Rail
2. Using the EZTrac™ Plus Gateway as a
template, mark and drill two (2) 3/16"
holes as shown.
(2) Buttonhead Torx Screws
Stainless Steel, 8-32 Thread
Size, 1 1/4” Long
(2) 18-8 Stainless
Steel Serrated
Flange Locknut
8-32 Thread Size
3. Insert supplied 8-32 button head screws from
the front side and secure with 8-32 serrated
flange nuts.
4. Plug in the Power Extension Harness to the
EZTrac™ Plus Gateway.
IMPORTANT: Insert the connector and turn ¼
turn clockwise until it clicks into place.
Front of
Chassis or
Trailer
Front of
Chassis or
Trailer
Page 3
PHILLIPS CONNECT TECHNOLOGIES
TRANSPORTATION TECHNOLOGIES REIMAGINED
PCT-EZTPIG REV0_8-21-19
Black to Black
ABS Extention Harness
Power Extention Harness
White to White
Blue To Blue
connect Here
ABS Harness Connector
Plug in he ABS Extension Harness in the Middle as Shown
PHILLIPS CONNECT TECHNOLOGIES
12012 BURKE STREET, SANTA FE SPRINGS, CA 90670
TEL: [phone]
WWW.PHILLIPS-CONNECT.COM
5. Locate the ABS TTMA 5 pin connector and
unplug it from the main harness.
Locate The TTMA
5 pin ABS Connector
Locate the ABS
TTMA 5 Pin
Connector
6. Plug in the ABS Extension Harness.
Connect Here
ABS Extension Harness
Connector
Plug in the ABS Extension Harness in the
Middle as Shown
Plug in the Power Extension Harness to
the ABS Extension Harness.
Power Extension Harness
Blue to Blue
Brown to
Brown
ABS Extension
Harness
White to
White
7. Matching the colored wires as shown below,
plug the three (3) male .180 bullet connectors
on the Power Extension Harness (currently
connected to the Gateway) into the three (3)
female .180 bullet connectors on the ABS
Extension Harness (currently installed on
the main harness).
8. Secure all loose harnesses with the included
cable ties. Use side cutter to cut back excess
cable ties.
9. Power up the asset.
4-Wire Ties