Phoenix Mecano HARTMANN ELECTRONIC PXE100A Series User manual

www.hartmann-electronic.com Rev. 1.0 1
PXI Express
Desktop PC Expansion
PCIE101A \ PXE100A
User’s Manual


www.hartmann-electronic.com Rev. 1.0 2
Revision History
Version: Notification of Change Date
1.0 10.01.2020
1.1 04.02.2020




















Imprint:
Hartmann Electronic GmbH
Motorstraße 43, D-70499 Stuttgart (Weilimdorf)
Telephone: [phone]
Telefax: + 49 711 8 66 11 91
E-Mail: [email protected]
Internet: www.hartmann-electronic.com

HartmannElectronicisalongstandingpartnerofthe
Embeddedindustryandhasavarietyofdifferentbackplanes.
Withourwideselectionofbackplanesandenclosureyoucan
Buildyourperfectsystemplatform
Copyright©2017
All rights and technical modifications reserved

www.hartmann-electronic.com Rev. 1.0 3
Contents
1. Safety.....................................................................................................................................................................4
Intended Application..............................................................................................................................................4
Safety Symbols .....................................................................................................................................................4
General Safety Precautions ..................................................................................................................................4
Safety Instructions.................................................................................................................................................5
Protection Against Electromagnetic Interference (EMI).....................................................................................5
Electrostatic Discharge Precautions...................................................................................................................5
Installation ..........................................................................................................................................................5
Location..............................................................................................................................................................5
Voltage Hazards.................................................................................................................................................5
System Overheating...........................................................................................................................................5
Mounting Considerations....................................................................................................................................6
Electrical Hazards...............................................................................................................................................6
Board Installation................................................................................................................................................6
2. Product Description ...............................................................................................................................................7
Related Documentation.........................................................................................................................................7
Chassis Description...............................................................................................................................................8
Block Diagram.......................................................................................................................................................9
PCIE101A PCIe Gen. 3 X4 PC Card..................................................................................................................9
PXE100A PCIe Gen. 2 Uplink to PXI Express.................................................................................................10
Front Panel LEDs................................................................................................................................................11
Cabling ................................................................................................................................................................11
Installation................................................................................................................................................................12
Installing Hardware..............................................................................................................................................12
Installing Software...............................................................................................................................................14
3. Specification ........................................................................................................................................................15
Electrical..............................................................................................................................................................15
DC Input ...........................................................................................................................................................15
Operating Environment ....................................................................................................................................15
Electromagnetic Compatibility..........................................................................................................................16
Environmental...................................................................................................................................................16
CE Compliance.................................................................................................................................................17
Mechanical ..........................................................................................................................................................18
4. Pin Assignment....................................................................................................................................................19
PXI Express System Controller Slot (4 Link Configuration)................................................................................20
5. Ordering Information............................................................................................................................................21

www.hartmann-electronic.com Rev. 1.0 4
1. Safety
Intended Application
The PXE100A series remote controller kit is not designed for stand-alone use -- in order to enable stand-
alone functionality, additional elements are required. An operational system is achieved only by way of
appropriate PXI Express Cards.
The completion and final testing of the units have been carried out by qualified technicians. These
instructions are intended to assist those who are qualified to operate this equipment.
Make sure that the finished system complies with the safety regulations currently applicable in the
country it is going to be used.
Safety Symbols
Hazardous voltage!
Familiarize yourself with the danger of electrical voltages and the safety
precautions before starting to work with parts that carry dangerous voltages
Caution!
This symbol indicates a condition where damage of the equipment or injury of
the service personnel could occur. To reduce the risk of damage or injury,
follow all steps or procedures as instructed.
Danger of electrostatic discharge!
Static electricity can damage sensitive components in a system. To avoid
damage, wear ESD wrist straps or at regular intervals touch blank enclosure
parts.
General Safety Precautions
Warning!
Voltages over 60 VDC can be present in this equipment. This equipment is
intended to be accessed, installed and maintained by qualified and trained service
personnel only.
This equipment is designed in accordance with protection class 1.
It must therefore be operated only with protective GND/earth connection.

www.hartmann-electronic.com Rev. 1.0 5
Safety Instructions
This user's manual is intended for system Integrators and hardware/software engineers.
This product has been designed to meet the relevant standard industrial safety requirements. It is not
intended to be used in applications other than that of its specific area of the office telecommunication
industry and industrial control. It is not designed nor intended for use in safety-critical applications, life-
sustaining appliances or in aircraft.
Only trained personnel or persons qualified in electronics or electrical engineering are authorized to
install, operate or maintain the product.
This section provides safety information about the following:
Protection against electromagnetic interference (EMI)
Electrostatic discharge precautions
System installation
ProtectionAgainstElectromagneticInterference(EMI)
This product has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules, EN 55022 Class A.
To ensure proper EMC shielding, operate the chassis only with filler panels covering all unpopulated
slots.
Ensure that all EMI gaskets make correct contact.
ElectrostaticDischargePrecautions
Electronic components can be easily destroyed by electrostatic discharge which can occur between
chassis components and a person.
Before working on the chassis, be sure that you are working in an ESD-safe environment or have
taken the necessary ESD precautions (ESD wrist strap, lab coat, etc.)
Installation
To avoid chassis damage, verify that the system environment meets or exceeds the environmental and
power requirements given in this guide before installation. In doing so, consider these guidelines:
Location
Locate the system in a stable area free of excessive movement or jarring, dust, smoke, and electrostatic
discharge (ESD). Make sure that the temperature does not exceed the operating temperature given in
the environmental requirements in this guide and allow room for proper air flow for cooling.
VoltageHazards
The system is powered with a power supply with the following voltage to the mains: 115/230VAC.
(Voltage range 90VAC to 264VAC)
This voltage is considered hazardous.
SystemOverheating
Ensure a clearance of at least 10 cm on both sides of the chassis to allow the needed air flow for proper
system cooling
Shelf ambient temperature may not exceed 50°C.

www.hartmann-electronic.com Rev. 1.0 6
MountingConsiderations
Assure that all components, structural or otherwise, were not loosened nor damaged during shipment
prior to use.
Do not operate under loose or damaged conditions as it may damage other parts of the system at large.
ElectricalHazards
The caution label on the system's rear, near the grounding studs, indicates a needed earth connection
due to the potential for high-leakage current which is considered hazardous.
High leakage current can cause injuries.
Ensure that the system is properly grounded at all times. Please account for the following condition:
This equipment shall be connected directly to the AC supply system earthing
BoardInstallation
Electrostatic discharge and incorrect board installation/removal can damage circuits or shorten their life.
Before touching the boards or electronic components, make sure that you are working in an ESD-
safe environment
Boards should be inserted and removed using their handles -- do not force the board by applying pressure to
the front panel.

www.hartmann-electronic.com Rev. 1.0 7
2. Product Description
The PXE100A series PXI Express Remote Controller is designed to operate in a PXI Express System Slot. The
controller complies with the PXI Express module form factor. With its use, a conventional Desktop PC is used to
control a PXI Express Chassis.
With the use of a Hartmann Electronic PCIE101A PC adapter, the Remote Controller is connected with a
standard PCIe X4 cable to the desktop PC. The interface of the PXE100A, as well as the interface of the
PCIE101A, are fully compliant with the PCI Express External Cable Specification, Revision 2.0.
Related Documentation
- PXI-5 PXI Express Hardware Specification
- CompactPCI PICMG 2.0 R. 3.0
- CompactPCI Express Specification PICMG EXP.0 Revision 2.0
- PCI Express External Cable Specification, Revision 2.0

www.hartmann-electronic.com Rev. 1.0 8
Chassis Description
The PXI Express Remote Controller is plugged into the PXI Express Backplane’s System Slot. The Space-saving
4 TE design allows ample space for additional system components as well as further PXI Express Modules,
conveniently placed directly next to the controller.
The Controller is suitable for PXI Express Chassis that implement a PXI Express System Slot 4-Link
configuration.

www.hartmann-electronic.com Rev. 1.0 9
Block Diagram
PCIE101APCIeGen.3X4PCCard
Figure 2-2 illustrates the hardware implementation of the PCIE101A PC Card.
Figure 2-1 PXI Express Remote Controller Block Diagram
The Block Diagram above outlines the Hardware implementation of the PCIe PC Card PCIE101A. As shown in
Figure 2-1, the PC-Card is available in both high and low profile versions of the front panel. This allows the PC
card to be plugged into any Desktop PC Chassis.
The PC Card can be plugged into a PCIe X4, PCIe X8 or PCIe X16 slot. The card re-drives a PCIe X4 link to the
standard PCIe X4 Cable Connector.
PCIe Gen. 3 data rates are supported with the card by utilizing a PCIe X4 Link.

www.hartmann-electronic.com Rev. 1.0 10
PXE100APCIeGen.2UplinktoPXIExpress
Figure 2-2 illustrates the hardware implementation of the PXI Express Remote Controller.
Figure 2-2 PXI Express Remote Controller Block Diagram
The Block Diagram above outlines the PXI Express Controller’s Hardware implementation. The controller’s
upstream port is implemented through a standard PCIe X4 Cable connector. A PCIe Gen. 2 X4 Link is supported
for connection with a desktop PC.
The controller can be plugged into any CPCI Express or PXI Express chassis’ system controller slot, which is
compliant with the necessary specifications. These specifications are listed in the “related document” section.

www.hartmann-electronic.com Rev. 1.0 11
Front Panel LEDs
The PXE100A provides a Power LED that as status indicator for the function of the PXI Express systems’ power
supply.
Figure 2-3 shows the location of the front panel LED.
Table 2-1 describes the front panel LED states
LED State Description
PWR Green Chassis Power OK
OFF One or more Power Rails of the chassis are not within the specified range
Cabling
Recommended copper cable Length.
The PCIE101A PC Card is implemented to support PCIe Gen. 3 signaling. To also support PCIe Gen. 3 signaling
at the Remote Controller side, the PCIe X4 cable should not exceed a length of 3m. The PXE100A Remote
controller supports PCIe Gen. 2 signaling.
The cable length should not exceed 7m in order to support PCIe Gen. 2 signaling.

www.hartmann-electronic.com Rev. 1.0 12
Installation
Installing Hardware
Installing the PCIE101A PC Card
Complete the following steps to install the PCIE100A in your computer.
1) Power off your computer.
Danger of electrostatic discharge!
To protect both yourself and the computer from electrical hazards,
your computer should remain off until you finish installing all hardware as
instructed.
2) Remove the top cover or access port to the PCI Express expansion slots.
3) Touch the metal part of the power supply case inside the computer to discharge any static electricity that might
be on your clothes or body.
4) Unplug the computer and wait 30 seconds to allow the energy stored in the computer’s power supply to fully
dissipate.
5) Select any available PCI Express expansion slot (X4, X8 or X16).
6) Locate the metal bracket that covers the cut-out in the back panel of the computer for the slot you have
selected. Remove and save the bracket-retaining screw and the bracket cover.
7) Line up the PCIE101A with the slot on the back panel. Slowly lower the PCIE101A until its card-edge
connector is resting on the expansion slot receptacle. Using slow, evenly distributed pressure, press the
PCIE101A straight down until it seats in the expansion slot.
8) Secure the PCIE101A to the back-panel rail using a bracket retaining screw.
9) Replace the computer cover.
10) Plug in the computer.

www.hartmann-electronic.com Rev. 1.0 13
Connecting a single PXI Express System to the Desktop PC
1) Install the Controller into the appropriate system slot.
Danger of electrostatic discharge!
To protect both yourself and the computer from electrical hazards,
The PXIe system should remain off until you finish installing all hardware as
instructed.
2) Power down your host system and the external PXI Express system.
3) Insert the PXI Express board into the system slot of the PXI Express system. Make sure that the front handle
of the cPCI board is locked.
4) Connect your host system through a PCIe X4 Cable to the upstream port of the PXI Express board.
5) Before applying power to the external PXI Express system, make sure that all other PXI Express boards are
installed correctly. You may follow the instruction of your PXI Express board supplier to install the board correctly.
6) Power up your external PXI Express system.
7) Power up your host system.
8) The PXI Express Remote controller should be enumerated automatically. There are no additional software
drivers required.
WARNING: Boards should slide easily when installing or removing them from the
shelf. Forcing the boards may cause damage to the interface connector pins.
Install filler panels in unused or empty slots.
Filler panels consists of a front panel (with or w/o air baffles), EMC gasket and mounting screws.
WARNING:
Close all empty chassis slots with filler panels. The filler panel prevents fan air from
escaping out of open slots.

www.hartmann-electronic.com Rev. 1.0 14
Installing Software
The Remote Controller does not require any additional software drivers. The Controller is enumerated fully with
the use of conventional standard PCI-to-PCI bridge drivers.
Note: The Controller does not implement a SMBus Interface. Therefore, the chassis can’t be enumerated with
the PXI Express Resource Manager. As a result, the hcassis will not appear in any vendor specific PXI Express
Explorer. However, all the PXI Express modules installed into the chassis will correctly appear in the PXI Express
Explorer.

www.hartmann-electronic.com Rev. 1.0 15
3. Specification
Electrical
DCInput
Applied through PXI Express Backplane
Operating Voltage Range +5V and +5V_AUX and +3V3
Power Consumption +5V: 0.8A ; total power consumption: 5W
OperatingEnvironment
Operating temperature range: -10… +85 °C
Storage temperature range: -40 °C… + 125 °C
Relative humidity range: 10% to 90%, noncondensing

www.hartmann-electronic.com Rev. 1.0 16
ElectromagneticCompatibility
This product meets or exceeds the requirements of the following EMC standards for electrical equipment
for measurement, control, and laboratory use:
• AS/NZS CISPR 11: Group 1, Class A emissions
• EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity
• EN 55011 (CISPR 11): Group 1, Class A emissions
• ICES-001: Class A emissions
• FCC 47 CFR Part 15B: Class A emissions
Environmental
Maximum Altitude: 2,000 m

www.hartmann-electronic.com Rev. 1.0 17
CECompliance
Declaration of Conformity

www.hartmann-electronic.com Rev. 1.0 18
Mechanical
Form Factor:
Eurocard (160x100mm): suitable for 19“-Racks. Front panel width 4HP (20.32mm).
Slot Requirement:
Single system controller slot

www.hartmann-electronic.com Rev. 1.0 19
4. Pin Assignment
The Pin assignment applies with the PXI-5 PXI Express Hardware Specification for a system slot 4 link
configuration.

www.hartmann-electronic.com Rev. 1.0 20
PXI Express System Controller Slot (4 Link Configuration)
Pin Z A B C D E F
XJ4 Connector
1 GND GA4 GA3 GA2 GA1 GA0 GND
2 GND +5Vaux GND SYSEN# WAKE# ALERT# GND
3 GND RSV RSV RSV RSV RSV GND
4 GND RSV RSV RSV RSV RSV GND
5 GND PXI_TRIG3 PXI_TRIG4 PXI_TRIG5 GND PXI_TRIG6 GND
6 GND PXI_TRIG2 GND RSV NC PXI_CLK10 GND
7 GND PXI_TRIG1 PXI_TRIG0 RSV GND PXI_TRIG7 GND
8 GND RSV GND RSV RSV PXI_LBR6 GND
Pin A B ab C D cd E F ef
XJ3 Connector
1 RSV RSV GND RSV RSV GND RSV RSV GND
2 RSV RSV GND PWR_OK PS_ON# GND LINKCAP PWRBTN# GND
3 SMBDAT SMBCLK GND
4REFCLK+ 4REFCLK- GND 2REFCLK+ 2REFCLK- GND
4 RSV PERST# GND
3REFCLK+ 3REFCLK- GND 1REFCLK+ 1REFCLK- GND
5 1PETp0 1PETn0 GND 1PERp0 1PERn0 GND NC NC GND
6 NC NC GND NC NC GND NC NC GND
7 NC NC GND NC NC GND
2PETp0 2PETn0
GND
8 NC NC GND NC NC GND
2PERp0 2PERn0
GND
9 NC NC GND NC NC GND NC NC GND
10 3PETp0 3PETn0 GND 3PERp0 3PERn0 GND NC NC GND
Pin A B ab C D cd E F ef
XJ2 Connector
1 NC NC GND NC NC GND NC NC GND
2 NC NC GND NC NC GND NC NC GND
3 4PETp0 4PETn0 GND 4PERp0 4PERn0 GND NC NC GND
4 NC NC GND NC NC GND NC NC GND
5 NC NC GND NC NC GND RSV RSV GND
6 RSV RSV GND RSV RSV GND RSV RSV GND
7 RSV RSV GND RSV RSV GND RSV RSV GND
8 RSV RSV GND RSV RSV GND RSV RSV GND
9 RSV RSV GND RSV RSV GND RSV RSV GND
10 RSV RSV GND RSV RSV GND RSV RSV GND
Pin Signals
XJ1 Connector
G GND
F NC
E NC
D GND
C 5V
B 3.3V
A GND