phpoc P5H-154 User manual

P5H-154 User Manual > Introduction
2021-12-10 Sollae Systems page 1 of 15
Overview
The P5H-154 is a programmable device that provides Ethernet function. Because this product equips
4 digital input ports, you can transfer the signals of the ports to remote hosts via network.
Programming on this product requires the use of PHPoC (PHP on Chip). PHPoC is quite similar in
syntax to PHP, the general-purpose scripting language. Therefore, anyone with experience in
programming can easily learn and use it.
※ Although PHPoC and PHP are quite similar in syntax, they are clearly different programming
languages. Refer to the PHPoC Language Reference and PHPoC vs PHP for detailed information.

P5H-154 User Manual > Features
2021-12-10 Sollae Systems page 2 of 15
Features
self-developed PHPoC interpreter
simple development environment via USB
10/100Mbps Ethernet
4 digital input ports
2 user-defined LEDs
self-developed TCP/IP stacks
Web Server
WebSocket, TLS
various libraries (Email, DNS, MySQL and Etc.)
dedicated development tool (PHPoC Debugger)

P5H-154 User Manual > H/W Specification
2021-12-10 Sollae Systems page 3 of 15
H/W Specification
H/W Specification
Power Input Power DC Jack, 5V (±0.5V)
Current Consumption typical - approximately 284mA
Dimension 94mm x 57mm x 24mm
Weight approximately 65g
Interface
Digital Input 6-pole terminal block, 4 digital inputs,
dry or wet contact
Network 10/100Mbps Ethernet
USB USB Device Port - for PC connection
LED 8 LEDs(System: 6, User-defined: 2)
Temperature (storage/operating) -40℃ ~ 85℃
Environment RoHS Compliant

P5H-154 User Manual > Layout
2021-12-10 Sollae Systems page 4 of 15
Layout
1. Supplying Power
DC 5V Input
This port is the input port for supplying power. The input voltage is DC 5V(±0.5V) and the
specification is as follows:

P5H-154 User Manual > Layout
2021-12-10 Sollae Systems page 5 of 15
2. Ethernet
Ethernet port supports 10/100Mbps Ethernet. This port is an RJ45 connector and it is mapped to
NET0 for programming.
3. Digital Input
4 digital input ports are an 6-pole (3.5mm pitch) terminal block. Each port is mapped a specific pin
of UIO0 for programming.
Lable Description UIO pin
DI.V common voltage input, DC 4.5V ~ 25V -
DI0 digital input #0 UIO0.22
DI1 digital input #1 UIO0.23
DI2 digital input #2 UIO0.24
DI3 digital input #3 UIO0.25
DI.G common ground -

P5H-154 User Manual > Layout
2021-12-10 Sollae Systems page 6 of 15
Circuit Diagram of the Digital Input Port
WET contact
The condition of input voltage is as follows:
division voltage
maximum input voltage DC 25V
minimum input voltage for ON state DC 4.5V or higher
maximum input voltage for OFF state DC 1V or lower
Refer to the following figure for connection with your device.

P5H-154 User Manual > Layout
2021-12-10 Sollae Systems page 7 of 15
Dry contact
An input port is ON under being short circuit between the port and DI.G port in this type. It means
additional power should be supplied between DI.V and DI.G. Refer to the following figure for
connection with your device.
NPN Transistor Connection
Refer to the following figure for connection with an NPN transistor.
PNP Transistor Connection
Refer to the following figure for connection with a PNP transistor.

P5H-154 User Manual > Layout
2021-12-10 Sollae Systems page 8 of 15
4. LED
This product has 8 LEDs. The user-defined LEDs are turned on when you output LOW to the UIO pin
connected.
Lable Color Description UIO pin
L0 Green User-defined LED UIO0.30
L1 Green User-defined LED UIO0.31
Di0 Green System LED - status of input port #0 UIO0.22
Di1 Green System LED - status of input port #1 UIO0.23
Di2 Green System LED - status of input port #2 UIO0.24
Di3 Green System LED - status of input port #3 UIO0.25
RJ45_G Green System LED - system status N/A
RJ45_Y Yellow System LED - network link status N/A
5. Function Button
The function button, which is inside the hole of the side panel, is used to operate this product as a
button setup mode.
6. USB Device Port for connection with PC
The USB device port is to connect with PC. You can access to P5H-154 via development tool by
connecting USB cable to this port.

P5H-154 User Manual > How to Use > Software(IDE)
2021-12-10 Sollae Systems page 9 of 15
Software (IDE)
PHPoC Debugger
PHPoC Debugger is a software used for developing and setting PHPoC products. You need to install
this program on your PC for using PHPoC.
PHPoC Debugger Download Page
PHPoC Debugger Manual
Functions and Features of PHPoC Debugger
Upload files from local PC to PHPoC
Download files in PHPoC to local PC
Edit files stored in PHPoC
Debug PHPoC scripts
Monitor resources of PHPoC
Configure parameters of PHPoC
Upgrade Firmware of PHPoC
Support MS Windows O/S

P5H-154 User Manual > How to Use > Connecting
2021-12-10 Sollae Systems page 10 of 15
Connecting Product
USB Connection
Connect the USB device port of P5H-154 to your PC via a USB cable.1.
Run PHPoC Debugger2.
Select connected COM PORT and press connect ( ) button.3.
If USB is successfully connected, connect button will be inactivated and disconnect button (4.
) will be activated
Remote Connection
P5H-154 provides the remote connection. Please refer to the PHPoC Debugger manual page for
details.