Physio Logic Smart Inflate User manual

Features:
• Smart Inflate™ Technology
• Auto memory for up to 60 readings
• One-Touch Operation
• Pre-Programmed Alert Feature
• Easy-to-read Display
• Time and Date Display
Smart Inflate™
Blood Pressure Monitor
TM
ys
Instruction Manual
106-940

Table of Contents
Smart Inflate™ measuring technology ....................3
About blood pressure .................................3
Blood pressure standard ...............................4
Blood pressure fluctuation .............................4
Before taking a measurement ...........................5
Installing batteries....................................7
Recalling memory....................................8
Time adjustment .....................................8
Statement of accuracy .................................3
Name / function of each part............................6
Display explanation ..................................7
Applying the arm cuff.................................9
Taking a measurement ...............................10
Troubleshooting ....................................11
Cautionary notes ....................................11
Specifications ......................................12
2

3
Smart Inflate™ Measuring Technology
Statement of Accuracy
This Physio Logic™ monitor uses trend-setting Smart Inflate™
Technology to detect your blood pressure. With one touch of a
button, it will automatically start to inflate and determine your
blood pressure by analysing your pressure oscillations while
inflating. When the measurement is completed, the device will
deflate the cuff and display your systolic, diastolic,
and pulse. Measurement time is significantly shortened and user
comfort is greatly enhanced.
automatically
Blood pressure measurements determined with Physio Logic™
are equivalent to those obtained by a trained observer using cuff /
stethoscope auscultation method, within the limits prescribed by
the American National Standard for Electronic or Automated
Sphygmomanometers (ANSI /AAMI).
Blood pressure is the pressure exerted on the arterial wall while
blood flows through the arteries. The pressure measured when the
heart contracts and sends blood out of the heart is systolic
(highest). The pressure measured when the heart dilates with blood
flowing back into the heart is called diastolic (lowest) blood
pressure.
High blood pressure’s strong correlation with cardiovascular
diseases and high morbidity has made measuring blood pressure a
necessity of identifying those at risk.
About Blood Pressure

4
Blood Pressure Standard
The Joint National Committee on prevention, detection, evalua-
tion, and treatment of high blood pressure has developed a blood
pressure standard, according to which areas of low and high risk
blood pressure are identified. This standard is a guideline as blood
pressure varies among different people and different age groups...
It is important that you consult with your physician regularly.
Your physician will tell you your normal blood pressure range as
well as the point at which you will be considered at risk.
Optimal <120 and <80
Normal <130 and <85
High-normal 130-139 or 85-89
Hypertension Stage 1 140-159 or 90-99
Hypertension Stage 2 160-179 or 100-109
Hypertension Stage 3 >180 or >110
Category Systolic (mm Hg) Diastolic (mm Hg)
Blood Pressure for Adults Age 18 and Older
Blood Pressure Fluctuation
Blood pressure fluctuates all the time! You should not be overly
worried if you encounter two or three measurements at high levels.
Blood pressure changes over the month and throughout the day.
(Case:
Male, 35 years old)
Wake
up
Arrive
office
Leave
office
Dinner
/ Sleep
Telephone
Discussion
Argument
in a meeting
18:00 Midnight
12:00
6:00
50
100
150 mmHg Systolic
Diastolic

5
Before Taking a Measurement
To help you obtain more accurate readings:
• Urinate if necessary.
• Remove any clothing and jewellery from your left arm. Placing
the cuff on anything other than bare skin can result in an
inaccurate reading.
• Sit in a comfortable position with your legs and ankles
uncrossed and your back supported.
• Sit quietly for 15 minutes before measuring your blood pressure.
• If you need to retake a reading, wait at least 5 minutes to allow
your circulation to return to normal.
• Pick a time of day, and take your blood pressure at about the
same time every day. Since your blood pressure varies at
different times of the day, this will make it easier for you to
compare your daily blood pressure readings.A good time to take
your blood pressure is in the morning, before breakfast.
• Don't smoke, eat or exercise for 30 minutes before taking your
blood pressure. These activities can change your blood pressure.
• Do not measure your blood pressure immediately after
consuming a large meal. To obtain more accurate readings,
please wait one hour before measuring.
• Only take your blood pressure in a quiet place and when you are
relaxed. Don't take your blood pressure when you are under
stress.Any stress will raise your blood pressure.
• Position your arm so that the cuff is at the level of your heart.
• If the monitor is stored at very low temperature (near freezing),
place it in a warm location for at least one hour before using it.

6
Date / Time - Set button
On/Off/Start
button
Memory recall
button
LCD display
Battery
compartment
Name / Function of Each Part
Arm cuff
Air tube and
connector
INDEX
22~32 cm
8.7~12.6 inch
2~3cm
0.8~1.2 inch
OK
INDEX

7
Display Explanation
Date and time
Systolic pressure
Diastolic pressure
Pulse rate
Appears when
measurement value is
stored in memory or is
recalled from memory.
Appears when blood
pressure reading is higher
than 160 mmHg (sys.) or
95 mmHg (dia.)
Appears when batteries
should be replaced.
Occurs when a error was made during measurement.
Shows the pulse rate per
minute.
Installing Batteries
1. Press down and lift the battery cover in the direction of the arrow
to open the battery compartment.
2. Install 4 “AA” 1.5 V Alkaline batteries according to the
indication inside the compartment.
3. Replace the battery cover by inserting the bottom tabs first, then
push in the top end of the battery cover.
Replace batteries when:
1. Low battery icon appears on display.
2. The On / Off / Start button is
pushed and nothing appears
on display.

8
Recalling Memory
1. To recall stored blood pressure readings from memory, simply
press the Memory button. The last set of memorized readings
will be displayed.
2. Another press of the Memory button will recall the previous set
of readings.
Time Adjustment
1. Press and hold the ( ) button for
more than 3 seconds to enter Time
Adjustment Mode. The display
will show a blinking Month.
2. Press the “ ” or “ ” to change the
Month.
3. Press the ( ) button again to
confirm the entry.
4. The display will then show a
blinking Date, followed by Hour
and Minutes. Repeat steps 2 and 3
to adjust the date/time setting.
+–
Hold for
more than
3 seconds
Blinking
month
Changing
month
Confirm
the
entry
or

Applying the Arm Cuff
1. Insert the cuff’s connecting tube into the unit.
2. Unwrap the arm cuff, leaving the “Index” end of the cuff through
the D-ring of the cuff.
3. Put your left arm through the cuff loop. Position the artery mark
( ) at the middle of your arm above the elbow, in line with your
middle finger. Tighten the cuff by pulling the “Index” end of the
cuff (snug, not tight).
4. Turn your left palm upward
and place the edge of the arm
cuff at approximately 2 to 3
cm above the
inner side of the elbow joint.
5. If the Index line falls within
the OK range, indicated at the
edge of the cuff, this cuff is
suitable for your use. If the
Index line falls out of the OK
range, you may need a
different size cuff.
(0.8” - 1.2”)
9
INDEX
INDEX
2 3 cm / 0,8” 1,2”

Taking a Measurement
1. Press the On / Off / Start button. All displays will appear for
approximately one second before returning to “0”.
2. The unit will automatically start to inflate and begin to measure
your blood pressure. During inflation, a changing measure of the
cuff pressure will be shown on the display.
3. When pressure reaches your systolic blood
pressure, the monitor will deflate the cuff
automatically. When the monitor
completes the measurement, it will display
and save your systolic, diastolic, and pulse
readings to memory. Up to 60 memories
can be saved.
This monitor has a built-in alert feature. If
your blood pressure reading is higher than
160 mmHg (SYS) or 95 mmHg (DIA), an
alert icon will show on the display. This
reminds you that your measurement fell
outside of the high blood pressure limits. If
this should persist, it is recommended to see
your physician.
4. Measurement is now completed. Press the On / Off / Start button
to turn the unit off. If no button is pressed, the unit will shut off
automatically in 1 minute.
10