Piazzetta IL 65/54 Quick start guide

Dear Customer,
Tha k you for havi g chose o e of our products, which is the result of years of experie ce a d co ti uous research aimed at maki g a
superior product i terms of safety, reliability a d performa ce.
This booklet co tai s i formatio a d advice for safe a d efficie t use of your product.
DT2010001-01
See the guarantee certificate enclosed with the product for the terms, limitations and exclusions.
In line with its policy of constant product improvement and renewal, the manufacturer may make changes without notice.
This document is the property of Gruppo Piazzetta S.p.A.; no part of it may e disclosed to third parties without the written permission
of Gruppo Piazzetta S.p.A.
All rights reserved y Gruppo Piazzetta S.p.A..
• This instruction booklet has been prepared by the manufacturer
and is an integral part of the product. In the event of sale or relo-
cation of the product make sure this booklet accompanies it, since
the information contained in it is addressed to the purchaser and
to anyone involved in the installation, use and maintenance of the
product.
• Read the instructions and the technical information contained in
this booklet carefully before proceeding with installation, use or
any repairs.
• The observance of the instructions and technical information in
this instruction booklet guarantees the safety of persons and pro-
perty; it also ensures more efficient operation and an increased li-
fespan.
• Gruppo Piazzetta S.p.A. cannot be held responsible for damage or
injury due to failure to comply with the instructions for installa-
tion, use and maintenance given in this booklet, or due to unau-
thorised alterations or to the use of other than original spare
parts.
• Appliance installation and use must conform with the manufac-
turer’s instructions as well as with European and national legisla-
tion and local regulations.
• The wall against which the product is to be placed must not be of
wood or any other flammable material. For correct installation it
is also important to maintain safety distances (refer to the section
entitled “MINIMUM SAFETY DISTANCES”).
• Prior to completing installation of the surround, light the stove
and when it has heated up check that the grate and that the flue
connection is correct.
• Check that the floor where the product is to be installed is per-
fectly level.
• Do not fix the heater unit in any way whatsoever, but simply place
it next to the surround.
• When handling the steel parts of the surround or the ceramic
parts it is advisable to use clean cotton gloves to avoid leaving fin-
gerprints that are difficult to remove at first time of cleaning
• The fireplace must be assembled by two persons.
• This appliance has been designed solely for heating. It is not re-
commended for cooking foods.
• Stop using the product in the event of fault or malfunctioning.
• The product you have purchased may differ slightly from the one
illustrated in this booklet since the pictures are only given as an
indication and not an exact portrayal.
UNI EN 832 . . . . . . . . . . . . . . . . . . . . . . . .Thermal performance of buildings - Calculation of energy use for heating
UNI EN 13229 . . . . . . . . . . . . . . . . . . . . . .Inset appliances including open fires fired by solid fuels - Requirements and test methods
UNI 10683:2005 . . . . . . . . . . . . . . . . . . . . .Heating appliances fired by wood or other solid biofuels - Installation requirements
UNI EN 13384 . . . . . . . . . . . . . . . . . . . . . .Chimneys - Thermal and fluid dynamic calculation methods
UNI 7129 . . . . . . . . . . . . . . . . . . . . . . . . . .Gas plants for domestic use fed by network distribution
UNI 10847 . . . . . . . . . . . . . . . . . . . . . . . . .Chimneys for generators feeded with liquid and solid flues - Maintenance and inspection
EN 1856-1 . . . . . . . . . . . . . . . . . . . . . . . . .Chimneys - Requirements for metal chimneys - Part 1: System chimney products
EN 1856-2 . . . . . . . . . . . . . . . . . . . . . . . . .Chimneys - Requirements for metal chimneys - Part 2: Metal liners and connecting flue pipes
UNI EN 1443 . . . . . . . . . . . . . . . . . . . . . . .Chimneys – General requirements
DIN 18 895 . . . . . . . . . . . . . . . . . . . . . . . . .Fireplaces
DIN 51731 class of measurement HP2 . .Fuels
IMPORTANT INFORMATION DT2010139-00
REFERENCE STANDARDS DT2010140-02
H07023830 / DT2000612 - Rev. 01
32
English

English
INDEX DT2010187-01
SECTION TITLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PAGE
1.0 GENERAL RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
1.1 SINGLE FLUEWAY OR CHIMNEY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
1.2 SOOT INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
1.3 CHIMNEY STACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
1.4 FRESH AIR INTAKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
1.5 INSTALLATION ENVIRONMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
1.6 CAPACITY LOAD OF THE FLOOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
1.7 HEATING CAPACITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
1.8 SUITABLE HEAT INSULATING MATERIALS . . . . . . . . . . . . . . . . . . . . . . . .39
1.9 MINIMUM SAFETY DISTANCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
1.10 CONNECTION TO THE FLUEWAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
1.11 LINING WALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
1.12 HOOD GRILLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
1.13 WOOD MANTEL PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
1.14 PREVENTION OF DOMESTIC FIRES . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
2.0 TECHNICAL DATA AND SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . .43
2.1 DESCRIPTION OF THE APPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
2.2 ACCESSORIES AND EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
2.3 FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
2.4 PRODUCT IDENTIFICATION DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
2.5 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
2.6 DIMENSION IL 65/49 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
2.7 DIMENSION IL 65/54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
2.8 DIMENSION IL 75/58 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
2.9 DIMENSION IL 75/64 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
3.0 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
3.1 PREPARING FIREPLACE INSERTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
3.2 BEFORE INSTALLING THE INSERT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
3.3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
3.4 ADJUSTING THE FLUE GAS/SMOKE DAMPER . . . . . . . . . . . . . . . . . . . . .49
4.0 VENTILATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
4.1 FAN SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
4.2 USE OF THE FANS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
4.3 FAN MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
4.4 REMOVING THE FAN BOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
4.5 FAN WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
5.0 USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
5.1 FUEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
5.2 COMBUSTION AIR REGULATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
5.4 LIGHTING FOR THE FIRST TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
5.5 LIGHTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
5.6 OPENING THE DOOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
5.6 NIGHT TIME OPERATION AT MINIMUM . . . . . . . . . . . . . . . . . . . . . . . . . .55
5.7 OPERATION UNDER ADVERSE WEATHER CONDITIONS . . . . . . . . . . . . .55
5.8 OVERHEATING AND EXTINGUISHING . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
6.0 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
6.1 PERIODIC CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
6.2 CLEANING THE PAINTED METAL PARTS . . . . . . . . . . . . . . . . . . . . . . . . .56
6.3 CLEANING THE GLASS (DAILY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
6.4 CLEANING THE GRATE AND THE ASH TRAY DRAWER . . . . . . . . . . . . . . .57
6.5 DISPOSAL OF ASHES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
6.6 CLEANING ALUKER® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
6.7 SEAL CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
6.8 REMOVING THE ALUKER INTERIOR AND GRATE . . . . . . . . . . . . . . . . . . .58
6.9 SHUTTING DOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
7.0 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
H07023830 / DT2000612 - Rev. 01 33
English
This booklet code H07023830 / DT2000612 - Rev. 01 - (08/2010) comprises 64 pages.

1.0 GENERAL RULES DT2010779-02
Before proceeding with installation, choose the most suitable position for your fireplace according to the indications given in the paragraph
“MINIMUM SAFETY DISTANCES” and to all the indications below.
DT2031171-00
SOOT REMOVAL
INSPECTION HOLE
CHIMNEY STACK
FLUE
CONNECTION TO FLUE
SAFETY DISTANCES
CHECK OF FLOOR
LOAD-BEARING CAPACITY
HOOD GRILLE
OUTER HOOD
PROTECTION FOR
ORNAMENTAL LEDGE
FIXED OPENING
FLOOR PROTECTION
FRESH AIR INTAKE
Fig. 1
H07023830 / DT2000612 - Rev. 01
34
English

English
DT2010169-00
1.1 SINGLE FLUEWAY OR CHIMNEY
Every appliance must have a vertical flue pipe operating by natural
draught to discharge the combustion gases outdoors.
The flue must:
- comply with regulations in force in the place of installation of the
appliance;
- be tight to the products of combustion, waterproof, suitably
insulated, made with materials resistant to the corrosion of the
gases and to stress;
- be connected to just one stove, fireplace or extraction hood;
- be properly sized, with constant free internal section, equal to or
greater than the diameter of the flue pipe of the stove and at least
3.5 m in length;
- be mainly in a vertical position with a deflection from the axis of no
more than 45° (Fig. 2);
- be at a suitable distance from combustible or flammable materials,
ensured by an air gap or suitable insulating material;
- be of uniform internal section, preferably round. Square or
rectangular sections must have rounded corners with a radius of at
least 20 mm and a maximum ratio between the sides of 1.5
(Fig. 3-4-5);
- the walls must be smooth if possible and without narrowing. Bends
must be regular and without discontinuity (Fig. 6).
It is for idden to make fixed or mo ile apertures on the flue
pipe to connect appliances other than the one to which it is
already connected.
It is for idden to pass other air ducts or service pipes inside
the flue pipe, however large it is.
If the flue pipe is an incorrect size or installed other than in
compliance with the a ove instructions, Gruppo Piazzetta
S.p.A. cannot e held lia le for malfunctioning of the product,
damage to property or injury to persons or animals.
DT2010031-01
1.2 SOOT INSPECTION
We recommend that the flue must have a chamber for collecting solid matter and any condensate located below the connection and which
may be easily inspected by means of an airtight door. (Fig.1)
DT2030258-00
DT2030050-00
Fig. 2
Fig. 3
MAX 45° NO
X
MINIMUM 3,5 M
Ø
DT2030188-00
Fig. 4
R (min.20)
Depositof creosote
DT2030189-00
Fig. 5
P
R (min. 20)
L (<_ 1,5 x P)
Deposit of creosote
DT2030190-00
Fig. 6
NO
NO
X
Minimo 3,5 m
MAX 45°
H07023830 / DT2000612 - Rev. 01 35
English

The chimney stack is a device fitted on the top of the chimney that is
designed to aid dispersion of the products of combustion in the
atmosphere.
The chimney stack must comply with the following requirements:
- it must have an internal section and shape the same as the flue (A);
- it must have a useful outlet section (B) of not less than twice that of
the flue (A);
-the part of the chimney that emerges from the roof or remains in
contact with the outside (e.g. in the case of a flat roof), must be
covered with brick or tile elements and in any case well insulated;
- It must be built in such a way as to prevent the penetration of rain,
snow and foreign matter into the flue and to ensure that in the event
of winds from all directions and angle, discharge of the combustion
products is assured (chimney stack with down-draught cowl).
Recommended distances for correct chimney operation.
To ensure trouble-free operation of the chimney and allow correct
dilution of the products of combustion in the air, the chimney stack
must be installed at the distances given below:
- 6-8 metres from any buildings or other obstacles that are higher
than the chimney stack;
- 50 centimetres higher than any obstacles located at a distance less
than 5 metres;
- outside the reflux area. The size and shape of this area differ
according to the angle of inclination of the roof and it is therefore
necessary to adopt the minimum heights shown below.
Example: Check the slope of the roof (colum α ), a d the
a ticipated dista ce of the chim ey stack from the axis of the ridge (colum A); if the dista ce is greater tha “A” the height of the chim ey
stack may be read i (colum H); if the dista ce is less tha “A” the chim ey stack must rise above the ridge by 0.5 metres.
6-8 m
A
B*
* B it is twice
of to A
A
BB
FLAT ROOF
SLOPING ROOF
0.50 m
0.50 m
0.50 m above the ridge
height of reflux
area Z
ridge axis
distance more than A
α
H min.
distance
min. than A
over 5 m 5 m or less 5 m or less
FLAT ROOF
SLOPING ROOF
0.50 m
0.50 m
0.50 m above the ridge
height of reflux
area Z
ridge axis
distance more than A
α
H min.
distance
min. than A
over 5 m 5 m or less 5 m or less
Pitch of the roof Horizontal width of reflux
area from ridge axis
Minimum height of
outlet from roof Height of reflux area
ααA H minimo Z
15° 1,85 m 1,00 m 0,50 m
30° 1,50 m 1,30 m 0,80 m
45° 1,30 m 2,00 m 1,50 m
60° 1,20 m 2,60 m 2,10 m
Fig. 7 Fig. 8
Fig. 9
Fig. 10
Fig. 11
DT2030051-00
DT2030052-00
DT2030053-00
DT2030192-00
DT2030191-00
1.3 CHIMNEY STACK DT2010025-03
H07023830 / DT2000612 - Rev. 01
36
English

English
To ensure trouble-free operation the stove/fireplace must have the
necessary air available for combustion and this is provided through
the fresh air intake.
The fresh air intake must:
- have a total free cross section at least equal to the size given in the
paragraph “TECHNICAL DATA”;
-be protected by a grille or suitable guard provided it does not
reduce the minimum recommended section;
- be in a position whereby it cannot be obstructed.
The airflow necessary for the fire may be obtained in different ways:
- through a fresh air intake direct into the room of installation (it is
advisable to place the air intake behind the hearth so that the air
warms up before flowing into the room through the canopy grille);
- with ducting through pipes direct to the room of installation,
increasing the recommended minimum free cross section by at
least 15%;
- from an adjacent room to the place of installation provided this air
flows freely through permanent apertures communicating with the
outside.
The adjacent room from which air is taken must not have a
low pressure compared to the exterior due to a counter
draught caused y the presence in that room of another
appliance in use or of a suction device.
The permanent apertures in the adjacent room must comply
with the requirements given a ove.
Com ustion air must not e taken from adjacent rooms used
as a garage or a com usti le materials store or for activities
posing a fire hazard.
1.4 FRESH AIR INTAKE DT2010170-01
H07023830 / DT2000612 - Rev. 01 37
English
Fig. 13
DT2030260-01
Fresh air
intake
Canopy
grille
Fig. 12
DT2030259-01
Fig. 14
DT2030261-01

DT2010033-01
1.5 INSTALLATION ENVIRONMENT
The appliance should be installed in a location which allows safe and convenient use as well as easy maintenance. If the product being
installed requires an electrical socket, the room must also be provided with an earthed power supply in accordance with current regulations.
The room where the appliance is to be installed must comply with the following requirements:
they must not e used as a garage, store for com usti le material or for activities with a risk of fire.
They must not e in a vacuum in relation to the outside environment due to the effect of contrary draught caused y the presence
in the room where the fi replace is installed of another appliance or an extractor device.
Do not use two stoves, a fireplace and a stove, a stove and a wood-fired cooking range, etc. in the same environment, since the
draught of one could affect the draught of the other.
- Devices suitable for cooking food with relative hoods without an extractor fan may only be used in kitchens.
- Gas appliances of type C are allowed (refer to current legislation and regulations in the place of installation)
Gas appliances of type B are not allowed (refer to current legislation and regulations in the place of installation)
The stove or fireplace must not e used simultaneously with collective type ventilation ducts with or without extractor fan, other
devices or other appliances such as: forced ventilation systems or other heating systems using ventilation to change the air. Such
systems could cause a vacuum in the environment of installation even if installed in adjoining or communicating rooms.
The stove or fireplace must not e used: in stairwells except in uildings with no more than two apartments; in corridors for
common use; in edrooms; in athrooms or shower-rooms.
DT2010171-00
1.6 CAPACITY LOAD OF THE FLOOR
Check the load-bearing capacity of the floor by adding together: the weight of the protections (lining walls), insulating materials, surround
(given in the surround instruction booklet) and the stove (given in the paragraph “TECHNICAL DATA”).
If the floor has an unsuitable load-bearing capacity, take adequate countermeasures.
DT2010130-01
1.7 HEATING CAPACITY
Check the heating capacity of the appliance by comparing the rated power given in the paragraph
“TECHNICAL DATA” with the power required
by the environment to be heated.
The energy requirement may be calculated approximately by multiplying the square metres of area by the height of the ceiling; the result is
then multiplied by a coefficient, which depends on the degree of insulation of the building, that is, on internal and external factors of the
dwelling:
a) Internal factors: type of window and door frames, thickness of the insulation and walls, type of building materials, presence of stairwells,
walls with extensive glazing, high ceilings, position of the rooms to be heated in relation to other adjacent heated or unheated rooms, …
b) External factors: geographical position, average outdoor temperature, exposure, wind speed, latitude, altitude, …
Example of approx mate calculat on of the energy requ rement to heat a f xed volume to 18/20° C:
The coeff c ent that is ormally used is determi ed accordi g to the real co ditio s as they occur case by case.
- From 0.04 to 0.05 kW per cubic metre i a well nsulated env ronment
- From 0.05 to 0.06 kW per cubic metre i a poorly nsulated env ronment
3 rooms measur ng 20m2 X (H ce l ng) 2.7m = 162 m3(volume)
I a e viro me t with a good degree of i sulatio , a average value (coefficie t) of 0.045 kW may be take
162 (volume) X 0.045 (kW) = 7.3 kW necessary (6300 kcal/h)
Co versio 1kW = 860 kcal/h
Consult a heating technician or engineer for a correct check and calculation of the requirement of the environments to e heated
(see “REFERENCE STANDARDS”).
H07023830 / DT2000612 - Rev. 01
38
English

English
DT2010173-01
1.8 SUITABLE HEAT INSULATING MATERIALS
Type of suita le heat insulating materials.
Material: mineral fibre; ceramic fibre; rock wool.
Form: sheets; mat; shells.
Specifications: specific weight of at least 245 kg/m³ with working temperature limit of at least 1000°C.
Thermal conductivity λ(400°C) ≤ 0.1 W/mK
Thickness: as shown in the figures in the paragraph “MINIMUM SAFETY DISTANCES”.
If the insulating material is not lining the walls, it must e fixed all over the surface of the walls with anchorage points every
30cm.
Material coded “AGI Q132” or “DIN 18895” is allowed for heat insulation.
DT2011906-00
1.9 MINIMUM SAFETY DISTANCES
- FLAMMABLE WALLS: the stove may be installed near flammable
walls provided suitable protection consisting of insulating and non-
combustible material is inserted.
To insulate the stove and to install the surround correctly, construct
a lining wall in non-flammable material (e.g. plasterboard) and in-
sert a “C” thick layer of insulating material between the two walls.
Always leave a gap “A” between the stove and the lining wall. (Fig.
15 - 16)
- NON-FLAMMABLE WALLS: always leave a gap of 5 cm between
the stove and the lining wall.
- FLAMMABLE CEILING: create an 8 cm false ceiling of non-flam-
mable material.
The minimum distance between the false ceiling and connection to
the flueway must be 20 cm, while the flue connection must be in-
sulated with at least 3 cm thick non-flammable material that is re-
sistant to high temperatures. (Fig. 15-16)
If the surround canopy and the flue connection are metal, the mi-
nimum distance from the false ceiling may be reduced to 10 cm,
but the insulation of the connection to the flueway must be at least
6 cm thick.
- NON-FLAMMABLE CEILING: the minimum distance between the
ceiling and connection to the flueway must be 20 cm.
If the floor is made of flammable material, it must be protected with
a layer of insulating material of thickness “E” while an air space “D”
must be left between the fireplace and the floor. (Fig. 15)
For insulation, use insulating material with the characteri-
stics given in the paragraph “SUITABLE HEAT INSULATING
MATERIALS”.
H07023830 / DT2000612 - Rev. 01 39
English
A C
B E D
Flammable
wall
Insulating
material
Flammable
floor
R
8 cm20 cm min.
Fig. 15
DT2032811-00
A
C
R
Flammable
wall
Insulating
material
Fig. 16
DT2032812-00
WALLS
CEILING
FLOOR

There is a radiation area in front of the stove which must be kept free of any flammable element, such as: carpets, curtains, wood furnishings,
ornaments, flammable liquids, fire-lighting products or firewood, etc.
This area is defined by the distance “R”. (Fig. 15 - 16)
Failure to comply with the a ove could cause a fire!!!
The minimum safety distances to be observed are given in the table below:
H07023830 / DT2000612 - Rev. 01
40
English
MODELS
IL 65/49 – 65/54 – 75/58 – 75/64
Aclearance from stove to flammable wall at the side cm 4
Bclearance from stove to flammable wall at the rear cm 4
Cthickness of insulating material for wall to side/rear cm 6
Dclearance from stove to flammable floor cm 4
Ethickness of floor insulating material cm 4
Rminimum clearance from stove front to flammable material cm 100
DT2011907-00
1.10 CONNECTION TO THE FLUEWAY
Connection to the flueway must be done using pipes as short as
possible without narrowing or restrictions and with a maximum slope
of 45°.
Flexi le metal or as estos-cement pipes must not e used
Pipes and bends or elbows must be made in compliance with current
regulations
WARNINGS WITH REGARD TO FLAMMABLE WALLS OR CEILING:
If the connection has to go through elements or walls in heat-
sensitive flammable materials, create a layer of at least 20 cm
insulation around the pipe. (Fig. 17)
After having drilled a hole in the wall to insert the pipe through into
the flueway, the air gaps must be filled with non-flammable, resilient
materials with a reduced capacity of heat transmission (e.g.
lightweight concrete). (Fig. 18)
Check that the connection to the flueway is gas/smoke-tight, since
the appliance operates in a vacuum.
It is recommended that the connector pipes e insulated with
insulating material having the characteristics given in the
paragraph “SUITABLE HEAT INSULATING MATERIALS”.
Check that the pipe does not penetrate too far into the flueway,
thereby choking the pipe for the passage of smoke and combustion
gases.
45°
FLUE
20
20
Insulation
Wall to be protected
Insulation
Maximum
Fig. 17
DT2030269-01
FLUE
Air gaps
Wall connection
flange
Fig. 18
DT2030270-00
DT2012032-00
DANGER AREA
FOR RADIATION

English
H07023830 / DT2000612 - Rev. 01 41
English
DT2011913-00
1.11 LINING WALL
The surround or the lining wall of the fireplace must be self-supporting regardless of the materials with which it is made and under no
circumstances must it come into contact with the fireplace. Furthermore, the surround must be made with non-flammable materials in
compliance with regulations.
For Gruppo Piazzetta S.p.A. surrounds, follow the instructions enclosed with the product.
Testing and lighting for first time
Only a visual inspection can be made in the intermediate stage for fireplaces, stoves and appliances that must be assembled or clad with
brickwork or require the use of cement binders. In this case operation of the whole installation must be tested after all the building works
directly connected with the “LIGHTING FOR THE FIRST TIME” test have been completed, following the instructions given in the booklet.
DT2010177-00
1.12 HOOD GRILLE
The hood grille has the function of allowing air to pass from inside
the hood to the environment or vice versa if the Multifuoco system
is installed.
Warm air comes out of the hood grille with the natural convection
system and it is therefore necessary to maintain the safety distances
from flammable materials such as: flammable ceilings or walls,
ledges/beams, furniture, curtains, etc.. The hood grille must be
installed at least 50 cm from the ceiling and with at least 30 cm safety
distance to the sides.
For the hood grille size, see the “TECHNICAL DATA” paragraph.
A non-closa le hood grille must e installed without
connecting it to the stove so that the warm air that has
stratified inside the lining wall can flow out.
With a ceiling over 3 metres high, a NON-CLOSABLE hood
grille must e installed on the hood lining at a height of 30 cm
from the ceiling to allow the stratified air to flow out.
MIN. 30 CM MIN. 30 CM
MIN. 30 CM
FLAMMABLE MATERIALS
FLAMMABLE MATERIALS
CEILING IN FLAMMABLE MATERIAL
Fig. 19
DT2030271-00
DT2010178-00
1.13 WOOD MANTEL PROTECTION
Wooden finishes, e.g. Wood mantels, may be mounted on the
surround.
Wood mantels must be:
- installed outside the heat radiation area;
- self-supporting;
- installed with 1cm air gap from the surround or from the heating
part;
The expansion joint is in ceramic fi re, which has the
function of insulating the surround from the metal structure of
the stove.
1 cm
Fireplace
Hood or surround
1 cm
Surround
Expansion joint
Load-bearing axis
Wood
mantel
Fig. 20
DT2030272-00

English
42 H07023830 / DT2000612 - Rev. 01
DT2010027-02
1.14 PREVENTION OF DOMESTIC FIRES
The product must be installed and used in compliance with the manufacturer’s instructions and European and national standards as well as
local regulations.
When a flue pipe passes through a wall or a ceiling, special installation methods must e applied (protection, thermal insulation,
distances from heat-sensitive materials, etc.) See the paragraph “CONNECTION TO THE FLUEWAY”
- It is also recommended that all elements made of combustible or inflammable material, such as beams, wooden furniture, curtaining,
flammable liquids, etc. be kept outside the heat radiation range of the stove and at a distance of at least 1 m from the heating block.
- For other information, see the paragraph “MINUMUM SAFETY DISTANCES” and “CONNECTION TO THE FLUEWAY”.
- The flue pipe, chimney stack, chimney and fresh air intake must always be free of obstructions, clean and checked periodically, that is, at
least twice during the seasonal period from the lighting of the stove and during its use. When the stove has not been used for some time
it is advisable to carry out the checks mentioned above. For further information, consult a chimneysweep.
- Only use recommended fuels (See paragraph “FUEL”).

English
43
H07023830 / DT2000612 - Rev. 01
2.0 TECHNICAL DATA AND SPECIFICATIONS DT2012033-00
DT2012034-00
2.1 DESCRIPTION OF THE APPLIANCE
The new line of wood-burning fireplace inserts IL comprises a range of compact stoves designed specifically for insertion into and therefore
the recovery of traditional fireplaces where it is necessary to improve performance and safety of use. The fireplace insert consists of an
internal high gauge steel body (thickness 4 mm) and an outer steel jacket. The structure is designed to ensure heating efficiency and
considerable heat recovery by the heat exchange that takes place between the walls of the hearth and the gap between the stove body and
its jacket, which allows air to circulate and be heated without it coming into contact with the flame. A ventilation kit is installed that, when
switched on, increases the heating action of the air by forcing it to circulate quicker and pushing it further away from the source of heat.
1
2
3
4
5
5
6
7
8
9
10
IL 65/49
DT2032852-00
No Description . . . . . . . . . . . . . . . . . . . . . . . . . .Qty
1) L.H. grate in cast iron . . . . . . . . . . . . . . . . . . . . . . . . .1
2) Aluker left side panel 267x262 . . . . . . . . . . . . . . . . . .1
3) Flue gas/smoke damper . . . . . . . . . . . . . . . . . . . . . . .1
4) Baffle plate support . . . . . . . . . . . . . . . . . . . . . . . . . .1
5) Aluker baffle plate 268x202 . . . . . . . . . . . . . . . . . . . .2
6) Aluker back panel 545x205 . . . . . . . . . . . . . . . . . . . .1
7) Aluker right side panel 267x262 . . . . . . . . . . . . . . . . .1
8) R.H. grate in cast iron . . . . . . . . . . . . . . . . . . . . . . . .1
9) Ash drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
10) Fan box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1
2
3
4
5
5
6
7
8
910
IL 65/54
DT2032860-00
No Description . . . . . . . . . . . . . . . . . . . . . . . . . .Qty
1) L.H. grate in cast iron . . . . . . . . . . . . . . . . . . . . . . . . .1
2) Aluker left side panel 267x312 . . . . . . . . . . . . . . . . .1
3) Flue gas/smoke damper . . . . . . . . . . . . . . . . . . . . . . .1
4) Baffle plate support . . . . . . . . . . . . . . . . . . . . . . . . . .1
5) Aluker baffle plate 268x202 . . . . . . . . . . . . . . . . . . . .2
6) Aluker back panel 545x255 . . . . . . . . . . . . . . . . . . . .1
7) Aluker right side panel 267x312 . . . . . . . . . . . . . . . .1
8) R.H. grate in cast iron . . . . . . . . . . . . . . . . . . . . . . . .1
9) Ash drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
10) Fan box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Italiano
44 H07023830 / DT2000612 - Rev. 01
1
2
3
4
5
5
6
8
910
7
IL 75/58
DT2032861-00
No Description . . . . . . . . . . . . . . . . . . . . . . . . . .Qty
1) L.H. grate in cast iron . . . . . . . . . . . . . . . . . . . . . . . . .1
2) Aluker left side panel 267x352 . . . . . . . . . . . . . . . . .1
3) Flue gas/smoke damper . . . . . . . . . . . . . . . . . . . . . . .1
4) Baffle plate support . . . . . . . . . . . . . . . . . . . . . . . . . .1
5) Aluker baffle plate 318x202 . . . . . . . . . . . . . . . . . . . .2
6) Aluker back panel 645x295 . . . . . . . . . . . . . . . . . . . .1
7) Aluker right side panel 267x352 . . . . . . . . . . . . . . . .1
8) R.H. grate in cast iron . . . . . . . . . . . . . . . . . . . . . . . .1
9) Ash drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
10) Fan box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1
2
3
4
5
5
6
7
8
910
IL 75/64
DT2032862-00
No Description . . . . . . . . . . . . . . . . . . . . . . . . . .Qty
1) L.H. grate in cast iron . . . . . . . . . . . . . . . . . . . . . . . . .1
2) Aluker left side panel 267x412 . . . . . . . . . . . . . . . . .1
3) Flue gas/smoke damper . . . . . . . . . . . . . . . . . . . . . . .1
4) Baffle plate support . . . . . . . . . . . . . . . . . . . . . . . . . .1
5) Aluker baffle plate 318x202 . . . . . . . . . . . . . . . . . . . .2
6) Aluker back panel 645x355 . . . . . . . . . . . . . . . . . . . .1
7) Aluker right side panel 267x412 . . . . . . . . . . . . . . . .1
8) R.H. grate in cast iron . . . . . . . . . . . . . . . . . . . . . . . .1
9) Ash drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
10) Fan box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Italiano
45
H07023830 / DT2000612 - Rev. 01
DT2012035-00
2.2 ACCESSORIES AND EQUIPMENT
DT2012036-00
2.3 FEATURES
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . wood (see “FUEL” paragraph)
Fireplace insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . black painted steel
Hearth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Aluker
Grate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . cast iron
Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . with ceramic glass heat-resistant up to 750°C
Handle: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . in steel, concealed flush with front
Primary air control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . manual regulation
Secondary air control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . manual regulation
Tertiary air control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . calibrated
Flue gas/smoke damper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . automatic opening
Ash tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . removable
Flue gas outlet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . top
Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . natural convection or forced ventilation with two front hot air outlets
Description Accessories
Right-hand glove In kit
Silicone paint spray can In kit
Hexagonal door handle tool In kit
Pipes and elbows for connection to the flueway Optional
Flue collar Optional
Front surround trim kit Optional
Mantel insulation kit Optional
Hot air pipe connector Ø 120 mm Optional
DT2011766-00
2.4 PRODUCT IDENTIFICATION DATA
Fig. 22
DT2032904-00
Fig. 21
DT2030944-00
Every product is identified by a rating plate showing the model and
the performance of the appliance as well as a plate giving the serial
number.
Both plates are located as indicated in the picture.
A label bearing the serial number is also applied on the cover last
page of the “INSTALLATION, OPERATION AND MAINTENANCE”
booklet.
Always give the information shown on these plates to the dealer or
the Service Centre when requesting service or spare parts.
Product name
Serial number
PRODUCTION
IDENTIFICATION
AND RATING PLATE

H07023830 / DT2000612 - Rev. 01
46
English
DT2012031-00
2.5 TECHNICAL DATA
These data are obtained using beech wood with moisture content below 20% and with intervals between stoking-up of approximately one
hour.
Use of this appliance is intermittent.
Techn cal data w th closed grate for flue calculat ons
The above values correspond approximately to a flue with section Ø 25 cm up to 4.5 m in height and Ø 18 over 4.5 m.
For model IL 65/49 and IL 65/54: Ø 20 cm up to 4.5 m in height and Ø 15 over 4.5 m.
U.M. IL 65/49 IL 65/54 IL 75/58 IL 75/64
Rated heat output kw 7.0 7.0 9.0 9.0
Consumption at rated heat output kg/h 1.9 1.9 2.4 2.4
Thermal efficiency % 80.1 80.1 80 80
CO content (with 13% O2) % 0.09 0.09 0.08 0.08
Certified in according to norm - EN 13229 EN 13229 EN 13229 EN 13229
Homologation number - RRF-29 10 2308 RRF-29 10 2308 RRF - 29 10 2275 RRF - 29 10 2275
Flue diameter cm 15 15 18 18
Firebox opening (WxH) cm 49x24.5 49x29.5 59x33.5 59x39.5
Firebed cm21346 1346 1618 1618
Weight kg105 110 125 132
Fresh air intake (recommended minimum section) cm2100 100 100 100
Combustion air fl ow rate with open intake m3/h - - - -
Convective air inlet/outlet (recommended minimum section) cm2350/350 350/350 350/350 350/350
U.M. IL 65/49 IL 65/54 IL 75/58 IL 75/64
Rated heat output kw 7.0 7.0 9.0 9.0
Mass of smoke g/s 5.4 5.4 8.0 8.0
Average temp. smoke in gas discharge pipe °C 345 345 335 335
Minimum draught Pa 12 12 12 12

H07023830 / DT2000612 - Rev. 01 47
English
2.6 DIMENSIONS IL 65/49
Ø15
42
15
51
68,5
65
32,5 32,5
42,5
49
12Ø
DT1020417-00
2.8 DIMENSIONS IL 75/58
Ø18
51
16,5
60
78,5 42,5
37,5 37,5
75
12Ø
58
DT1020419-00
2.7 DIMENSIONS IL 65/54
Ø15 15
47
68,5
56
42,5
32,5 32,5
65
12Ø
54
DT1020418-00
2.9 DIMENSIONS IL 75/64
Ø18 16,5
57
78,5 42,5
66 64
37,5 37,5
75
12Ø
DT1020420-00
Dimensions in cm
Dimensions in cm
Dimensions in cm
Dimensions in cm

H07023830 / DT2000612 - Rev. 01
48
English
3.0 INSTALLATION DT2012037-00
Profili di compensazione Dadi M4
Fig. 23
DT2032863-00
DT2012037-00
3.1 PREPARING FIREPLACE INSERTS
The wood-burning fireplace insert “IL” is provided with upper and
side filler elements.
Before placing the insert in its final location, the filler elements must
be screwed to it using the M4 nuts provided in the kit, first fitting the
side elements and then the upper one (fig. 23).
Push the filler elements as far as they will go to the rear before fully
tightening the nuts; if necessary it is in any case possible to make
small adjustments and alignments by making the pins of the ele-
ments slide in the relative slots.
Even if the “FRONT SURROUND TRIM KIT” is to e used, the
filler elements must e installed.
DT2012037-00
3.2 BEFORE INSTALLING THE INSERT
• Check the flue pipe, remove any closures or dampers and clean the pipe.
• Check that the structure of the existing fireplace/hearth is in good condition and if it is not, it must be made good.
• Check that there is a fresh air intake and if there is not, make a hole with a minimum section of 150-200 cm².
• Make sure there is a 220V electric socket available and that the fan power cable can pass.
• Rigid metal pipes must be used for connection to the flueway and must be installed so that no gas can enter into or leak out of the system.
• The flueway must always have an equal or greater section than that of the flue gas outlet pipe indicated in the paragraph “TECHNICAL DATA”.
• If building work is required to change the existing fireplace, before completing the masonry try fitting the fireplace insert.
• If the fireplace insert is installed in a larger hearth venting to an existing flueway, PIAZZETTA S.p.A. will supply, on request, an optional sur-
round trim. Follow the attached instructions before installing the insert.
• To install the flue collar, carefully read the accompanying instructions.
DT2012037-00
3.3 INSTALLATION
• Place and wall-in the flue collar (optional) for the flue gas outlet pipe to pass through, as low down as possible in the canopy (see atta-
ched instructions).
• Use fire-retardant materials between the flueway and the flue collar to create a hermetic insulating layer.
• Insert the connector and support it with the relative pipe clip.
• Fit the fireplace insert into the existing fireplace, placing the flue gas outlet collar in line with the hole of the flue collar.
• Working through the flue gas hole, remove the flue gas outlet pipe support and lower the pipe towards the fireplace insert. Insert the flue
gas outlet collar. Fit the flue collar with the pipe into position from inside the insert, and fasten it to the ceiling of the fireplace insert using
the four nuts and washers provided in the kit (see detail “A” fig. 24).
• Insert the flue gas/smoke baffle plates with relative support in the upper part (see detail ”B” fig. 24).
• Check that everything is fitted correctly and light the fire so that it burns slowly.
Filler elements Nuts M4

H07023830 / DT2000612 - Rev. 01 49
English
3
1
2
5
6
4
7
AB
D
C
Dado M5 Vite
Fig. 24
DT2012037-00
3.4 ADJUSTING THE FLUE GAS/SMOKE DAMPER
To adjust the flue gas/smoke damper, loosen the nut M5, tighten the screw to the required position and then tighten the nut M5 again (see
detail “D” fig. 24).
For nominal power set the smoke damper so that, with the door closed, it is also fully closed.
Whether the fireplace insert is installed in an existing fireplace or in a new fireplace with a wooden mantel, the underside of the
mantel must e insulated.
For this purpose there is a mantel insulating kit (optional), which may e fixed onto all wooden mantels (see detail “C” fig. 24
and instructions regarding the mantel insulation kit).
DT2032903-00
1 Flue collar
2 Connector
3 Backfill
4 Mantel insulation
5 Front surround trim
6 Fireplace insert
7 Internal ventilation kit
Nut M5 Screw

English
50 H07023830 / DT2000612 - Rev. 01
4.0 VENTILATION DT2012038-00
The wood burning fireplace inserts IL are fitted with a ventilation system consisting of two fans with connection terminals, a thermostatic
sensor and a selector switch with three settings: “I – 0 – II”.
The ventilation system should be considered as: in the manual mode of operation (first speed) when in position “I”, automatic mode of
operation (first speed) when in position “0”, automatic mode of operation (second speed) when in position “II”. In the automatic mode of
operation positions (0 and II), the fan motors are controlled by the thermostatic sensor, which therefore acts as a switch; under normal
operating conditions, when the temperature inside the fireplace insert is more than around 60°C, the sensor closes the electrical circuit
thereby automatically activating the ventilation system and vice versa if the temperature is lower.
A suita le system for cutting off the electricity supply (plug or line circuit reaker) must e installed upstream of the wiring provided.
DT2012038-00
4.1 FAN SPECIFICATIONS
Free flow rate . . . . . . . . . . . . . . 2 x 50 [m³/h]
Power . . . . . . . . . . . . . . . . . . . . 2 x 12 [W]
Frequency . . . . . . . . . . . . . . . . 50 [Hz]
Voltage . . . . . . . . . . . . . . . . . . 230 [V]
Fig. 25
DT2032867-00
DT2012038-00
4.2 USE OF THE FANS
The fan motors can be activated immediately by moving the selector
switch (to be found bottom right of the product) to position “I”.
In the manual mode position, the fans continue to work even
after the hearth has completely cooled.
When the fire is burning steadily (approx. 30 minutes after lighting),
you can put the selector switch to position “I”. After approx. 2-3
hours you can put the switch to position “0 or II”, so that the fans are
switched on and off by the thermostatic sensor, which acts on the
fans when the temperature is around 60° C. (Fig. 25).
DT2012038-00
4.3 FAN MAINTENANCE
Periodically and at least once a year, clean the fans, removing the dust that can build up on the rotating blades.
Follow the procedure given in the section “REMOVING THE FAN BOX” for cleaning and removing the fans.
All work on the appliance and on the wiring must e carried out y qualified personnel and with the electricity supply switched off.