PIEPEIEGG Smart Dumbbell User manual
/TYZX[IZOUT3GT[GR
Important Notice
APP Connection
1. The total weight of a single dumbbell is 2kg, and the adjustable
weights are 1.0kg, 1.5kg and 2kg. An metal block is built in the
base cover to increase its weight. The base cover needs to be
rotated and unscrewed when the weight needs to be replaced, the
base cover shall be upward and unscrew carefully during the
unscrewing process to prevent the base cover from sliding and
damaging people, animals and articles.
2. Dumbbells should be placed out of the reach of children when
not in use. Children must be supervised when using the dumbbell
to avoid danger cause by misuse.
3. This dumbbell is an indoor product without waterproof
function. Please do not splash or put the electronic part into the
water.
4. When the electronic module of dumbbell is removed for
charging, it can be press and push out from the rear hole.
5. When using the product, please adjust the weight according to
your own needs to prevent injury caused by excessive weight
movement.
6. When using the product, please hold the dumbbell tightly to
prevent it from slipping.
7. Do not use it on other parts of the body or exercise in an
abnormal way to avoid injury to the body.
9SGXZ*[SHHKRR
Dumbbell Installation & Dismantle
પޢа>SS
ٗ-Յୢ֚ՅவԭӳিОܑՌি澝үЇЈثܑ澝եܑДܑ
1- 1-1-
Thank you for purchasing and use of our smart dumbbell. Please
read the precautions before use to avoid unnecessary risks in using
the product. Wishing you have a happy user experience.
Weight adjustment, metal pcs install & dismantle
Adjust the weight of the dumbbell：Unscrew the base cover of
dumbbell. There is an metal block in the base cover. When
unscrewing, the base faces upward to prevent accidents
Weight of dumbbell: the weight of dumbbell itself is 1kg,
equipped with 2pcs 500g metal counter weights, and the total
weight of dumbbell is 2kg. The weight can be adjusted from
1kg to 1.5kg & 2kg. If 1kg weight is required, remove the two
internal movable metal blocks; If 1.5kg is required, only short
iron blocks shall be installed. When 2kg is used, all the metal
blocks shall be installed;
Screw on the base cover after installing the metal block;
Function Description
The electronic counting module is powered by built-in lithium
battery. When charging is required, press down from the hole
at the back of the dumbbell to take the electronic counting
module;
The electronic module use the Micro – USB charging cable for
charging
Finished charging, pay attention of the direction when
installing the module, with the charger facing down and the
module pressed down;
Installation and Dismantle of Electronic counting module
Objective remind
Countdown Time
Dumbbell Number Calorie
Skipping Goal Ranking list
Skipping Speed Skipping Time
History
Number
Countdown Mode BT
Voice Enable
Display status and operation method of electronic counting module
Display Status Operation Procedure
Touch key: the touch area is at the ngerprint
Press and hold for 5 seconds to start the machine
In free mode, press and hold for 3 seconds again
to start the free motion screen. To Click the
ngerprint area to back the home screen
Power on display: China-Beijing time will be
displayed after power on. If it is connected the
mobile app, the time can be synchronized. If there
is no connection, it will automatically record the
time state when it was last powered o
After exiting the movement, click again to see the
above symbol display and switch to
countdown mode
In the countdown time mode, press and hold for 3
seconds to enter the button then the countdown
starts.
After exiting the countdown, click again to see the
above symbol display, switch to the
countdown mode, long press for three seconds,
release the key and enter the countdown mode.
Click the ngerprint area to back the home screen
Press and hold for three seconds to release, switch
to free mode , and the symbol in the upper
left corner displays
1.Turn on the Bluetooth & GPS on the phone, search "Tuya Smart"
in Application Center to download
4. Choose add device and then turn on the smart dumbbell, the
Bluetooth icon on the LCD screen “ ”will ashes, the APP
will identify and add the smart dumbbell automatically.
5. Device binding is completed and can be used normally.
2. Switch on the electronic module
3. Click to add device
Smart Dumbbell
Smart Dumbbell
Ѻ
Time Countdown: after setting
the time, click the conrm key
Number Countdown: the
default is 100. You can modify
to any number. Click on any
area to conrm the number
History record:
there is no
history record
for the rst use;
data will appear
after the rst
use
There are three
selectable
modes on the
main page.
Choose the
mode you
prefer
Low battery
indicator
Voice on/o
Button
8. After the smart dumbbell is connected to the mobile APP, the
voice broadcast function will provide encouragement in various
languages with the number increasing during the exercise to let the
exercising be more fun. Based on your preference, this function can
be turn on or o with the following methods.
6. For the rst use, please input
your personal physical
parameters; gender, height and
weight on the APP personal
settings page. App can then
provide your personal exercise
index. The number of daily
training goals can be set on the
settings page.
7. Successfully added, click the dumbbell icon to start using. The
picture on the right shows the eect after entering the dumbbell
movement page. You can set goals according to your own needs,
and choose the sports modes.
Smart Dumbbell
/TYZX[IZOUT3GT[GR
Important Notice
APP Connection
1. The total weight of a single dumbbell is 2kg, and the adjustable
weights are 1.0kg, 1.5kg and 2kg. An metal block is built in the
base cover to increase its weight. The base cover needs to be
rotated and unscrewed when the weight needs to be replaced, the
base cover shall be upward and unscrew carefully during the
unscrewing process to prevent the base cover from sliding and
damaging people, animals and articles.
2. Dumbbells should be placed out of the reach of children when
not in use. Children must be supervised when using the dumbbell
to avoid danger cause by misuse.
3. This dumbbell is an indoor product without waterproof
function. Please do not splash or put the electronic part into the
water.
4. When the electronic module of dumbbell is removed for
charging, it can be press and push out from the rear hole.
5. When using the product, please adjust the weight according to
your own needs to prevent injury caused by excessive weight
movement.
6. When using the product, please hold the dumbbell tightly to
prevent it from slipping.
7. Do not use it on other parts of the body or exercise in an
abnormal way to avoid injury to the body.
9SGXZ*[SHHKRR
Dumbbell Installation & Dismantle
પޢа>SS
ٗ-Յୢ֚ՅவԭӳিОܑՌি澝үЇЈثܑ澝եܑДܑ
1- 1-1-
Thank you for purchasing and use of our smart dumbbell. Please
read the precautions before use to avoid unnecessary risks in using
the product. Wishing you have a happy user experience.
Weight adjustment, metal pcs install & dismantle
Adjust the weight of the dumbbell：Unscrew the base cover of
dumbbell. There is an metal block in the base cover. When
unscrewing, the base faces upward to prevent accidents
Weight of dumbbell: the weight of dumbbell itself is 1kg,
equipped with 2pcs 500g metal counter weights, and the total
weight of dumbbell is 2kg. The weight can be adjusted from
1kg to 1.5kg & 2kg. If 1kg weight is required, remove the two
internal movable metal blocks; If 1.5kg is required, only short
iron blocks shall be installed. When 2kg is used, all the metal
blocks shall be installed;
Screw on the base cover after installing the metal block;
Function Description
The electronic counting module is powered by built-in lithium
battery. When charging is required, press down from the hole
at the back of the dumbbell to take the electronic counting
module;
The electronic module use the Micro – USB charging cable for
charging
Finished charging, pay attention of the direction when
installing the module, with the charger facing down and the
module pressed down;
Installation and Dismantle of Electronic counting module
Objective remind
Countdown Time
Dumbbell Number Calorie
Skipping Goal Ranking list
Skipping Speed Skipping Time
History
Number
Countdown Mode BT
Voice Enable
Display status and operation method of electronic counting module
Display Status Operation Procedure
Touch key: the touch area is at the ngerprint
Press and hold for 5 seconds to start the machine
In free mode, press and hold for 3 seconds again
to start the free motion screen. To Click the
ngerprint area to back the home screen
Power on display: China-Beijing time will be
displayed after power on. If it is connected the
mobile app, the time can be synchronized. If there
is no connection, it will automatically record the
time state when it was last powered o
After exiting the movement, click again to see the
above symbol display and switch to
countdown mode
In the countdown time mode, press and hold for 3
seconds to enter the button then the countdown
starts.
After exiting the countdown, click again to see the
above symbol display, switch to the
countdown mode, long press for three seconds,
release the key and enter the countdown mode.
Click the ngerprint area to back the home screen
Press and hold for three seconds to release, switch
to free mode , and the symbol in the upper
left corner displays
1.Turn on the Bluetooth & GPS on the phone, search "Tuya Smart"
in Application Center to download
4. Choose add device and then turn on the smart dumbbell, the
Bluetooth icon on the LCD screen “ ”will ashes, the APP
will identify and add the smart dumbbell automatically.
5. Device binding is completed and can be used normally.
2. Switch on the electronic module
3. Click to add device
Smart Dumbbell
Smart Dumbbell
Ѻ
Time Countdown: after setting
the time, click the conrm key
Number Countdown: the
default is 100. You can modify
to any number. Click on any
area to conrm the number
History record:
there is no
history record
for the rst use;
data will appear
after the rst
use
There are three
selectable
modes on the
main page.
Choose the
mode you
prefer
Low battery
indicator
Voice on/o
Button
8. After the smart dumbbell is connected to the mobile APP, the
voice broadcast function will provide encouragement in various
languages with the number increasing during the exercise to let the
exercising be more fun. Based on your preference, this function can
be turn on or o with the following methods.
6. For the rst use, please input
your personal physical
parameters; gender, height and
weight on the APP personal
settings page. App can then
provide your personal exercise
index. The number of daily
training goals can be set on the
settings page.
7. Successfully added, click the dumbbell icon to start using. The
picture on the right shows the eect after entering the dumbbell
movement page. You can set goals according to your own needs,
and choose the sports modes.
Smart Dumbbell
/TYZX[IZOUT3GT[GR
Important Notice
APP Connection
1. The total weight of a single dumbbell is 2kg, and the adjustable
weights are 1.0kg, 1.5kg and 2kg. An metal block is built in the
base cover to increase its weight. The base cover needs to be
rotated and unscrewed when the weight needs to be replaced, the
base cover shall be upward and unscrew carefully during the
unscrewing process to prevent the base cover from sliding and
damaging people, animals and articles.
2. Dumbbells should be placed out of the reach of children when
not in use. Children must be supervised when using the dumbbell
to avoid danger cause by misuse.
3. This dumbbell is an indoor product without waterproof
function. Please do not splash or put the electronic part into the
water.
4. When the electronic module of dumbbell is removed for
charging, it can be press and push out from the rear hole.
5. When using the product, please adjust the weight according to
your own needs to prevent injury caused by excessive weight
movement.
6. When using the product, please hold the dumbbell tightly to
prevent it from slipping.
7. Do not use it on other parts of the body or exercise in an
abnormal way to avoid injury to the body.
9SGXZ*[SHHKRR
Dumbbell Installation & Dismantle
પޢа>SS
ٗ-Յୢ֚ՅவԭӳিОܑՌি澝үЇЈثܑ澝եܑДܑ
1- 1-1-
Thank you for purchasing and use of our smart dumbbell. Please
read the precautions before use to avoid unnecessary risks in using
the product. Wishing you have a happy user experience.
Weight adjustment, metal pcs install & dismantle
Adjust the weight of the dumbbell：Unscrew the base cover of
dumbbell. There is an metal block in the base cover. When
unscrewing, the base faces upward to prevent accidents
Weight of dumbbell: the weight of dumbbell itself is 1kg,
equipped with 2pcs 500g metal counter weights, and the total
weight of dumbbell is 2kg. The weight can be adjusted from
1kg to 1.5kg & 2kg. If 1kg weight is required, remove the two
internal movable metal blocks; If 1.5kg is required, only short
iron blocks shall be installed. When 2kg is used, all the metal
blocks shall be installed;
Screw on the base cover after installing the metal block;
Function Description
The electronic counting module is powered by built-in lithium
battery. When charging is required, press down from the hole
at the back of the dumbbell to take the electronic counting
module;
The electronic module use the Micro – USB charging cable for
charging
Finished charging, pay attention of the direction when
installing the module, with the charger facing down and the
module pressed down;
Installation and Dismantle of Electronic counting module
Objective remind
Countdown Time
Dumbbell Number Calorie
Skipping Goal Ranking list
Skipping Speed Skipping Time
History
Number
Countdown Mode BT
Voice Enable
Display status and operation method of electronic counting module
Display Status Operation Procedure
Touch key: the touch area is at the ngerprint
Press and hold for 5 seconds to start the machine
In free mode, press and hold for 3 seconds again
to start the free motion screen. To Click the
ngerprint area to back the home screen
Power on display: China-Beijing time will be
displayed after power on. If it is connected the
mobile app, the time can be synchronized. If there
is no connection, it will automatically record the
time state when it was last powered o
After exiting the movement, click again to see the
above symbol display and switch to
countdown mode
In the countdown time mode, press and hold for 3
seconds to enter the button then the countdown
starts.
After exiting the countdown, click again to see the
above symbol display, switch to the
countdown mode, long press for three seconds,
release the key and enter the countdown mode.
Click the ngerprint area to back the home screen
Press and hold for three seconds to release, switch
to free mode , and the symbol in the upper
left corner displays
1.Turn on the Bluetooth & GPS on the phone, search "Tuya Smart"
in Application Center to download
4. Choose add device and then turn on the smart dumbbell, the
Bluetooth icon on the LCD screen “ ”will ashes, the APP
will identify and add the smart dumbbell automatically.
5. Device binding is completed and can be used normally.
2. Switch on the electronic module
3. Click to add device
Smart Dumbbell
Smart Dumbbell
Ѻ
Time Countdown: after setting
the time, click the conrm key
Number Countdown: the
default is 100. You can modify
to any number. Click on any
area to conrm the number
History record:
there is no
history record
for the rst use;
data will appear
after the rst
use
There are three
selectable
modes on the
main page.
Choose the
mode you
prefer
Low battery
indicator
Voice on/o
Button
8. After the smart dumbbell is connected to the mobile APP, the
voice broadcast function will provide encouragement in various
languages with the number increasing during the exercise to let the
exercising be more fun. Based on your preference, this function can
be turn on or o with the following methods.
6. For the rst use, please input
your personal physical
parameters; gender, height and
weight on the APP personal
settings page. App can then
provide your personal exercise
index. The number of daily
training goals can be set on the
settings page.
7. Successfully added, click the dumbbell icon to start using. The
picture on the right shows the eect after entering the dumbbell
movement page. You can set goals according to your own needs,
and choose the sports modes.
Smart Dumbbell
/TYZX[IZOUT3GT[GR
Important Notice
APP Connection
1. The total weight of a single dumbbell is 2kg, and the adjustable
weights are 1.0kg, 1.5kg and 2kg. An metal block is built in the
base cover to increase its weight. The base cover needs to be
rotated and unscrewed when the weight needs to be replaced, the
base cover shall be upward and unscrew carefully during the
unscrewing process to prevent the base cover from sliding and
damaging people, animals and articles.
2. Dumbbells should be placed out of the reach of children when
not in use. Children must be supervised when using the dumbbell
to avoid danger cause by misuse.
3. This dumbbell is an indoor product without waterproof
function. Please do not splash or put the electronic part into the
water.
4. When the electronic module of dumbbell is removed for
charging, it can be press and push out from the rear hole.
5. When using the product, please adjust the weight according to
your own needs to prevent injury caused by excessive weight
movement.
6. When using the product, please hold the dumbbell tightly to
prevent it from slipping.
7. Do not use it on other parts of the body or exercise in an
abnormal way to avoid injury to the body.
9SGXZ*[SHHKRR
Dumbbell Installation & Dismantle
પޢа>SS
ٗ-Յୢ֚ՅவԭӳিОܑՌি澝үЇЈثܑ澝եܑДܑ
1- 1-1-
Thank you for purchasing and use of our smart dumbbell. Please
read the precautions before use to avoid unnecessary risks in using
the product. Wishing you have a happy user experience.
Weight adjustment, metal pcs install & dismantle
Adjust the weight of the dumbbell：Unscrew the base cover of
dumbbell. There is an metal block in the base cover. When
unscrewing, the base faces upward to prevent accidents
Weight of dumbbell: the weight of dumbbell itself is 1kg,
equipped with 2pcs 500g metal counter weights, and the total
weight of dumbbell is 2kg. The weight can be adjusted from
1kg to 1.5kg & 2kg. If 1kg weight is required, remove the two
internal movable metal blocks; If 1.5kg is required, only short
iron blocks shall be installed. When 2kg is used, all the metal
blocks shall be installed;
Screw on the base cover after installing the metal block;
Function Description
The electronic counting module is powered by built-in lithium
battery. When charging is required, press down from the hole
at the back of the dumbbell to take the electronic counting
module;
The electronic module use the Micro – USB charging cable for
charging
Finished charging, pay attention of the direction when
installing the module, with the charger facing down and the
module pressed down;
Installation and Dismantle of Electronic counting module
Objective remind
Countdown Time
Dumbbell Number Calorie
Skipping Goal Ranking list
Skipping Speed Skipping Time
History
Number
Countdown Mode BT
Voice Enable
Display status and operation method of electronic counting module
Display Status Operation Procedure
Touch key: the touch area is at the ngerprint
Press and hold for 5 seconds to start the machine
In free mode, press and hold for 3 seconds again
to start the free motion screen. To Click the
ngerprint area to back the home screen
Power on display: China-Beijing time will be
displayed after power on. If it is connected the
mobile app, the time can be synchronized. If there
is no connection, it will automatically record the
time state when it was last powered o
After exiting the movement, click again to see the
above symbol display and switch to
countdown mode
In the countdown time mode, press and hold for 3
seconds to enter the button then the countdown
starts.
After exiting the countdown, click again to see the
above symbol display, switch to the
countdown mode, long press for three seconds,
release the key and enter the countdown mode.
Click the ngerprint area to back the home screen
Press and hold for three seconds to release, switch
to free mode , and the symbol in the upper
left corner displays
1.Turn on the Bluetooth & GPS on the phone, search "Tuya Smart"
in Application Center to download
4. Choose add device and then turn on the smart dumbbell, the
Bluetooth icon on the LCD screen “ ”will ashes, the APP
will identify and add the smart dumbbell automatically.
5. Device binding is completed and can be used normally.
2. Switch on the electronic module
3. Click to add device
Smart Dumbbell
Smart Dumbbell
Ѻ
Time Countdown: after setting
the time, click the conrm key
Number Countdown: the
default is 100. You can modify
to any number. Click on any
area to conrm the number
History record:
there is no
history record
for the rst use;
data will appear
after the rst
use
There are three
selectable
modes on the
main page.
Choose the
mode you
prefer
Low battery
indicator
Voice on/o
Button
8. After the smart dumbbell is connected to the mobile APP, the
voice broadcast function will provide encouragement in various
languages with the number increasing during the exercise to let the
exercising be more fun. Based on your preference, this function can
be turn on or o with the following methods.
6. For the rst use, please input
your personal physical
parameters; gender, height and
weight on the APP personal
settings page. App can then
provide your personal exercise
index. The number of daily
training goals can be set on the
settings page.
7. Successfully added, click the dumbbell icon to start using. The
picture on the right shows the eect after entering the dumbbell
movement page. You can set goals according to your own needs,
and choose the sports modes.
Smart Dumbbell
/TYZX[IZOUT3GT[GR
Important Notice
APP Connection
1. The total weight of a single dumbbell is 2kg, and the adjustable
weights are 1.0kg, 1.5kg and 2kg. An metal block is built in the
base cover to increase its weight. The base cover needs to be
rotated and unscrewed when the weight needs to be replaced, the
base cover shall be upward and unscrew carefully during the
unscrewing process to prevent the base cover from sliding and
damaging people, animals and articles.
2. Dumbbells should be placed out of the reach of children when
not in use. Children must be supervised when using the dumbbell
to avoid danger cause by misuse.
3. This dumbbell is an indoor product without waterproof
function. Please do not splash or put the electronic part into the
water.
4. When the electronic module of dumbbell is removed for
charging, it can be press and push out from the rear hole.
5. When using the product, please adjust the weight according to
your own needs to prevent injury caused by excessive weight
movement.
6. When using the product, please hold the dumbbell tightly to
prevent it from slipping.
7. Do not use it on other parts of the body or exercise in an
abnormal way to avoid injury to the body.
9SGXZ*[SHHKRR
Dumbbell Installation & Dismantle
પޢа>SS
ٗ-Յୢ֚ՅவԭӳিОܑՌি澝үЇЈثܑ澝եܑДܑ
1- 1-1-
Thank you for purchasing and use of our smart dumbbell. Please
read the precautions before use to avoid unnecessary risks in using
the product. Wishing you have a happy user experience.
Weight adjustment, metal pcs install & dismantle
Adjust the weight of the dumbbell：Unscrew the base cover of
dumbbell. There is an metal block in the base cover. When
unscrewing, the base faces upward to prevent accidents
Weight of dumbbell: the weight of dumbbell itself is 1kg,
equipped with 2pcs 500g metal counter weights, and the total
weight of dumbbell is 2kg. The weight can be adjusted from
1kg to 1.5kg & 2kg. If 1kg weight is required, remove the two
internal movable metal blocks; If 1.5kg is required, only short
iron blocks shall be installed. When 2kg is used, all the metal
blocks shall be installed;
Screw on the base cover after installing the metal block;
Function Description
The electronic counting module is powered by built-in lithium
battery. When charging is required, press down from the hole
at the back of the dumbbell to take the electronic counting
module;
The electronic module use the Micro – USB charging cable for
charging
Finished charging, pay attention of the direction when
installing the module, with the charger facing down and the
module pressed down;
Installation and Dismantle of Electronic counting module
Objective remind
Countdown Time
Dumbbell Number Calorie
Skipping Goal Ranking list
Skipping Speed Skipping Time
History
Number
Countdown Mode BT
Voice Enable
Display status and operation method of electronic counting module
Display Status Operation Procedure
Touch key: the touch area is at the ngerprint
Press and hold for 5 seconds to start the machine
In free mode, press and hold for 3 seconds again
to start the free motion screen. To Click the
ngerprint area to back the home screen
Power on display: China-Beijing time will be
displayed after power on. If it is connected the
mobile app, the time can be synchronized. If there
is no connection, it will automatically record the
time state when it was last powered o
After exiting the movement, click again to see the
above symbol display and switch to
countdown mode
In the countdown time mode, press and hold for 3
seconds to enter the button then the countdown
starts.
After exiting the countdown, click again to see the
above symbol display, switch to the
countdown mode, long press for three seconds,
release the key and enter the countdown mode.
Click the ngerprint area to back the home screen
Press and hold for three seconds to release, switch
to free mode , and the symbol in the upper
left corner displays
1.Turn on the Bluetooth & GPS on the phone, search "Tuya Smart"
in Application Center to download
4. Choose add device and then turn on the smart dumbbell, the
Bluetooth icon on the LCD screen “ ”will ashes, the APP
will identify and add the smart dumbbell automatically.
5. Device binding is completed and can be used normally.
2. Switch on the electronic module
3. Click to add device
Smart Dumbbell
Smart Dumbbell
Ѻ
Time Countdown: after setting
the time, click the conrm key
Number Countdown: the
default is 100. You can modify
to any number. Click on any
area to conrm the number
History record:
there is no
history record
for the rst use;
data will appear
after the rst
use
There are three
selectable
modes on the
main page.
Choose the
mode you
prefer
Low battery
indicator
Voice on/o
Button
8. After the smart dumbbell is connected to the mobile APP, the
voice broadcast function will provide encouragement in various
languages with the number increasing during the exercise to let the
exercising be more fun. Based on your preference, this function can
be turn on or o with the following methods.
6. For the rst use, please input
your personal physical
parameters; gender, height and
weight on the APP personal
settings page. App can then
provide your personal exercise
index. The number of daily
training goals can be set on the
settings page.
7. Successfully added, click the dumbbell icon to start using. The
picture on the right shows the eect after entering the dumbbell
movement page. You can set goals according to your own needs,
and choose the sports modes.
Smart Dumbbell
/TYZX[IZOUT3GT[GR
Important Notice
APP Connection
1. The total weight of a single dumbbell is 2kg, and the adjustable
weights are 1.0kg, 1.5kg and 2kg. An metal block is built in the
base cover to increase its weight. The base cover needs to be
rotated and unscrewed when the weight needs to be replaced, the
base cover shall be upward and unscrew carefully during the
unscrewing process to prevent the base cover from sliding and
damaging people, animals and articles.
2. Dumbbells should be placed out of the reach of children when
not in use. Children must be supervised when using the dumbbell
to avoid danger cause by misuse.
3. This dumbbell is an indoor product without waterproof
function. Please do not splash or put the electronic part into the
water.
4. When the electronic module of dumbbell is removed for
charging, it can be press and push out from the rear hole.
5. When using the product, please adjust the weight according to
your own needs to prevent injury caused by excessive weight
movement.
6. When using the product, please hold the dumbbell tightly to
prevent it from slipping.
7. Do not use it on other parts of the body or exercise in an
abnormal way to avoid injury to the body.
9SGXZ*[SHHKRR
Dumbbell Installation & Dismantle
પޢа>SS
ٗ-Յୢ֚ՅவԭӳিОܑՌি澝үЇЈثܑ澝եܑДܑ
1- 1-1-
Thank you for purchasing and use of our smart dumbbell. Please
read the precautions before use to avoid unnecessary risks in using
the product. Wishing you have a happy user experience.
Weight adjustment, metal pcs install & dismantle
Adjust the weight of the dumbbell：Unscrew the base cover of
dumbbell. There is an metal block in the base cover. When
unscrewing, the base faces upward to prevent accidents
Weight of dumbbell: the weight of dumbbell itself is 1kg,
equipped with 2pcs 500g metal counter weights, and the total
weight of dumbbell is 2kg. The weight can be adjusted from
1kg to 1.5kg & 2kg. If 1kg weight is required, remove the two
internal movable metal blocks; If 1.5kg is required, only short
iron blocks shall be installed. When 2kg is used, all the metal
blocks shall be installed;
Screw on the base cover after installing the metal block;
Function Description
The electronic counting module is powered by built-in lithium
battery. When charging is required, press down from the hole
at the back of the dumbbell to take the electronic counting
module;
The electronic module use the Micro – USB charging cable for
charging
Finished charging, pay attention of the direction when
installing the module, with the charger facing down and the
module pressed down;
Installation and Dismantle of Electronic counting module
Objective remind
Countdown Time
Dumbbell Number Calorie
Skipping Goal Ranking list
Skipping Speed Skipping Time
History
Number
Countdown Mode BT
Voice Enable
Display status and operation method of electronic counting module
Display Status Operation Procedure
Touch key: the touch area is at the ngerprint
Press and hold for 5 seconds to start the machine
In free mode, press and hold for 3 seconds again
to start the free motion screen. To Click the
ngerprint area to back the home screen
Power on display: China-Beijing time will be
displayed after power on. If it is connected the
mobile app, the time can be synchronized. If there
is no connection, it will automatically record the
time state when it was last powered o
After exiting the movement, click again to see the
above symbol display and switch to
countdown mode
In the countdown time mode, press and hold for 3
seconds to enter the button then the countdown
starts.
After exiting the countdown, click again to see the
above symbol display, switch to the
countdown mode, long press for three seconds,
release the key and enter the countdown mode.
Click the ngerprint area to back the home screen
Press and hold for three seconds to release, switch
to free mode , and the symbol in the upper
left corner displays
1.Turn on the Bluetooth & GPS on the phone, search "Tuya Smart"
in Application Center to download
4. Choose add device and then turn on the smart dumbbell, the
Bluetooth icon on the LCD screen “ ”will ashes, the APP
will identify and add the smart dumbbell automatically.
5. Device binding is completed and can be used normally.
2. Switch on the electronic module
3. Click to add device
Smart Dumbbell
Smart Dumbbell
Ѻ
Time Countdown: after setting
the time, click the conrm key
Number Countdown: the
default is 100. You can modify
to any number. Click on any
area to conrm the number
History record:
there is no
history record
for the rst use;
data will appear
after the rst
use
There are three
selectable
modes on the
main page.
Choose the
mode you
prefer
Low battery
indicator
Voice on/o
Button
8. After the smart dumbbell is connected to the mobile APP, the
voice broadcast function will provide encouragement in various
languages with the number increasing during the exercise to let the
exercising be more fun. Based on your preference, this function can
be turn on or o with the following methods.
6. For the rst use, please input
your personal physical
parameters; gender, height and
weight on the APP personal
settings page. App can then
provide your personal exercise
index. The number of daily
training goals can be set on the
settings page.
7. Successfully added, click the dumbbell icon to start using. The
picture on the right shows the eect after entering the dumbbell
movement page. You can set goals according to your own needs,
and choose the sports modes.
Smart Dumbbell
/TYZX[IZOUT3GT[GR
Important Notice
APP Connection
1. The total weight of a single dumbbell is 2kg, and the adjustable
weights are 1.0kg, 1.5kg and 2kg. An metal block is built in the
base cover to increase its weight. The base cover needs to be
rotated and unscrewed when the weight needs to be replaced, the
base cover shall be upward and unscrew carefully during the
unscrewing process to prevent the base cover from sliding and
damaging people, animals and articles.
2. Dumbbells should be placed out of the reach of children when
not in use. Children must be supervised when using the dumbbell
to avoid danger cause by misuse.
3. This dumbbell is an indoor product without waterproof
function. Please do not splash or put the electronic part into the
water.
4. When the electronic module of dumbbell is removed for
charging, it can be press and push out from the rear hole.
5. When using the product, please adjust the weight according to
your own needs to prevent injury caused by excessive weight
movement.
6. When using the product, please hold the dumbbell tightly to
prevent it from slipping.
7. Do not use it on other parts of the body or exercise in an
abnormal way to avoid injury to the body.
9SGXZ*[SHHKRR
Dumbbell Installation & Dismantle
પޢа>SS
ٗ-Յୢ֚ՅவԭӳিОܑՌি澝үЇЈثܑ澝եܑДܑ
1- 1-1-
Thank you for purchasing and use of our smart dumbbell. Please
read the precautions before use to avoid unnecessary risks in using
the product. Wishing you have a happy user experience.
Weight adjustment, metal pcs install & dismantle
Adjust the weight of the dumbbell：Unscrew the base cover of
dumbbell. There is an metal block in the base cover. When
unscrewing, the base faces upward to prevent accidents
Weight of dumbbell: the weight of dumbbell itself is 1kg,
equipped with 2pcs 500g metal counter weights, and the total
weight of dumbbell is 2kg. The weight can be adjusted from
1kg to 1.5kg & 2kg. If 1kg weight is required, remove the two
internal movable metal blocks; If 1.5kg is required, only short
iron blocks shall be installed. When 2kg is used, all the metal
blocks shall be installed;
Screw on the base cover after installing the metal block;
Function Description
The electronic counting module is powered by built-in lithium
battery. When charging is required, press down from the hole
at the back of the dumbbell to take the electronic counting
module;
The electronic module use the Micro – USB charging cable for
charging
Finished charging, pay attention of the direction when
installing the module, with the charger facing down and the
module pressed down;
Installation and Dismantle of Electronic counting module
Objective remind
Countdown Time
Dumbbell Number Calorie
Skipping Goal Ranking list
Skipping Speed Skipping Time
History
Number
Countdown Mode BT
Voice Enable
Display status and operation method of electronic counting module
Display Status Operation Procedure
Touch key: the touch area is at the ngerprint
Press and hold for 5 seconds to start the machine
In free mode, press and hold for 3 seconds again
to start the free motion screen. To Click the
ngerprint area to back the home screen
Power on display: China-Beijing time will be
displayed after power on. If it is connected the
mobile app, the time can be synchronized. If there
is no connection, it will automatically record the
time state when it was last powered o
After exiting the movement, click again to see the
above symbol display and switch to
countdown mode
In the countdown time mode, press and hold for 3
seconds to enter the button then the countdown
starts.
After exiting the countdown, click again to see the
above symbol display, switch to the
countdown mode, long press for three seconds,
release the key and enter the countdown mode.
Click the ngerprint area to back the home screen
Press and hold for three seconds to release, switch
to free mode , and the symbol in the upper
left corner displays
1.Turn on the Bluetooth & GPS on the phone, search "Tuya Smart"
in Application Center to download
4. Choose add device and then turn on the smart dumbbell, the
Bluetooth icon on the LCD screen “ ”will ashes, the APP
will identify and add the smart dumbbell automatically.
5. Device binding is completed and can be used normally.
2. Switch on the electronic module
3. Click to add device
Smart Dumbbell
Smart Dumbbell
Ѻ
Time Countdown: after setting
the time, click the conrm key
Number Countdown: the
default is 100. You can modify
to any number. Click on any
area to conrm the number
History record:
there is no
history record
for the rst use;
data will appear
after the rst
use
There are three
selectable
modes on the
main page.
Choose the
mode you
prefer
Low battery
indicator
Voice on/o
Button
8. After the smart dumbbell is connected to the mobile APP, the
voice broadcast function will provide encouragement in various
languages with the number increasing during the exercise to let the
exercising be more fun. Based on your preference, this function can
be turn on or o with the following methods.
6. For the rst use, please input
your personal physical
parameters; gender, height and
weight on the APP personal
settings page. App can then
provide your personal exercise
index. The number of daily
training goals can be set on the
settings page.
7. Successfully added, click the dumbbell icon to start using. The
picture on the right shows the eect after entering the dumbbell
movement page. You can set goals according to your own needs,
and choose the sports modes.
Smart Dumbbell
/TYZX[IZOUT3GT[GR
Important Notice
APP Connection
1. The total weight of a single dumbbell is 2kg, and the adjustable
weights are 1.0kg, 1.5kg and 2kg. An metal block is built in the
base cover to increase its weight. The base cover needs to be
rotated and unscrewed when the weight needs to be replaced, the
base cover shall be upward and unscrew carefully during the
unscrewing process to prevent the base cover from sliding and
damaging people, animals and articles.
2. Dumbbells should be placed out of the reach of children when
not in use. Children must be supervised when using the dumbbell
to avoid danger cause by misuse.
3. This dumbbell is an indoor product without waterproof
function. Please do not splash or put the electronic part into the
water.
4. When the electronic module of dumbbell is removed for
charging, it can be press and push out from the rear hole.
5. When using the product, please adjust the weight according to
your own needs to prevent injury caused by excessive weight
movement.
6. When using the product, please hold the dumbbell tightly to
prevent it from slipping.
7. Do not use it on other parts of the body or exercise in an
abnormal way to avoid injury to the body.
9SGXZ*[SHHKRR
Dumbbell Installation & Dismantle
પޢа>SS
ٗ-Յୢ֚ՅவԭӳিОܑՌি澝үЇЈثܑ澝եܑДܑ
1- 1-1-
Thank you for purchasing and use of our smart dumbbell. Please
read the precautions before use to avoid unnecessary risks in using
the product. Wishing you have a happy user experience.
Weight adjustment, metal pcs install & dismantle
Adjust the weight of the dumbbell：Unscrew the base cover of
dumbbell. There is an metal block in the base cover. When
unscrewing, the base faces upward to prevent accidents
Weight of dumbbell: the weight of dumbbell itself is 1kg,
equipped with 2pcs 500g metal counter weights, and the total
weight of dumbbell is 2kg. The weight can be adjusted from
1kg to 1.5kg & 2kg. If 1kg weight is required, remove the two
internal movable metal blocks; If 1.5kg is required, only short
iron blocks shall be installed. When 2kg is used, all the metal
blocks shall be installed;
Screw on the base cover after installing the metal block;
Function Description
The electronic counting module is powered by built-in lithium
battery. When charging is required, press down from the hole
at the back of the dumbbell to take the electronic counting
module;
The electronic module use the Micro – USB charging cable for
charging
Finished charging, pay attention of the direction when
installing the module, with the charger facing down and the
module pressed down;
Installation and Dismantle of Electronic counting module
Objective remind
Countdown Time
Dumbbell Number Calorie
Skipping Goal Ranking list
Skipping Speed Skipping Time
History
Number
Countdown Mode BT
Voice Enable
Display status and operation method of electronic counting module
Display Status Operation Procedure
Touch key: the touch area is at the ngerprint
Press and hold for 5 seconds to start the machine
In free mode, press and hold for 3 seconds again
to start the free motion screen. To Click the
ngerprint area to back the home screen
Power on display: China-Beijing time will be
displayed after power on. If it is connected the
mobile app, the time can be synchronized. If there
is no connection, it will automatically record the
time state when it was last powered o
After exiting the movement, click again to see the
above symbol display and switch to
countdown mode
In the countdown time mode, press and hold for 3
seconds to enter the button then the countdown
starts.
After exiting the countdown, click again to see the
above symbol display, switch to the
countdown mode, long press for three seconds,
release the key and enter the countdown mode.
Click the ngerprint area to back the home screen
Press and hold for three seconds to release, switch
to free mode , and the symbol in the upper
left corner displays
1.Turn on the Bluetooth & GPS on the phone, search "Tuya Smart"
in Application Center to download
4. Choose add device and then turn on the smart dumbbell, the
Bluetooth icon on the LCD screen “ ”will ashes, the APP
will identify and add the smart dumbbell automatically.
5. Device binding is completed and can be used normally.
2. Switch on the electronic module
3. Click to add device
Smart Dumbbell
Smart Dumbbell
Ѻ
Time Countdown: after setting
the time, click the conrm key
Number Countdown: the
default is 100. You can modify
to any number. Click on any
area to conrm the number
History record:
there is no
history record
for the rst use;
data will appear
after the rst
use
There are three
selectable
modes on the
main page.
Choose the
mode you
prefer
Low battery
indicator
Voice on/o
Button
8. After the smart dumbbell is connected to the mobile APP, the
voice broadcast function will provide encouragement in various
languages with the number increasing during the exercise to let the
exercising be more fun. Based on your preference, this function can
be turn on or o with the following methods.
6. For the rst use, please input
your personal physical
parameters; gender, height and
weight on the APP personal
settings page. App can then
provide your personal exercise
index. The number of daily
training goals can be set on the
settings page.
7. Successfully added, click the dumbbell icon to start using. The
picture on the right shows the eect after entering the dumbbell
movement page. You can set goals according to your own needs,
and choose the sports modes.
Smart Dumbbell
FCC Warning
3GJKOT)NOTG
Note:
1. App binding function:
considering the security of
personal sports data, each
dumbbell device can only bind
one mobile app account. When
account a binds the dumbbell
electronic module, account B cannot bind the electronic module
without unbinding. If the user forgets his account number and
cannot log in, he can press the reset button on the back of the
electronic module to restore the factory settings. Long press for
10 seconds to restore, and the module will shut down
automatically. After that, the user needs to long press 5 seconds
to start up. At this time, the binding of the previous account can
be released.
2. Normal unbinding method of account: in the app bound device
screen, select the bound device need to be delete, and then click
delete.
3. Reset function: there is a reset button on the back of the
electronic module to restore the factory settings.
History record: Dumbbell
data will be automatically
saved in the APP for your
reference
Troubleshooting
When the display cannot be turned on after it
is turned o, the screen does not display.
Please use the charging cable to activate the
device. After the screen is displayed, it can be
use normally.
Please remove the module from the dumbbell
handle, press the key on the back of the
module for 10 seconds and release it. At the
same time, you can see that the electronic
module is turned o and the system enters
reset. At this time, touch the icon at the corner
to restart it
Charging
Plug
Input
Voltage
Input
Current
Battery
Capacity
Charging
Time
Charging Indicator
Light Status
Micro-
USB 2.0 4.75-5.25V 0.5~0.8A 120mAh 1~2H
Solution
Problem description
Item
When the machine
is turn on, the
screen is displayed,
but there is no
response when
operating the
touch screen
Unable to boot or
crash handling
method
Please note that the Bluetooth icon displayed
on the page is blue, and the dumbbell has been
successfully connected to the mobile phone
app. If the oine icon is displayed, it indicates
that the dumbbell has not been successfully
connected.
If it is displayed as oine:
1. Please check whether the dumbbell is on;
2. Check whether the Bluetooth on the phone is
turned on;
3. Pull down and refresh the page, and check
whether the connection is successful after 2
seconds;
Dumbbells have
been added to the
app page, but the
icon shows oine
and cannot be
connect with
dumbbell
1
2
Charging Specification
White LED
on: 15% or above，
Red Light on: Below
15%, please
re-charge
Product Name:
Bluetooth Version
Bluetooth Distance
Handle Size
Material
Product Weight
Display
Battery Spec.
Standby Time
Standby Maintenance
Battery Life
Smart Dumbbell
Bluetooth 5.0
10 meters
245.42 X 70.7mm
ABS+PC, Metal & EVA
Around 4 KG
Nixie tube display
Lion Battery 3.7V/120mAh
Around 10 hours
Recommend re-charge every 3months
3 Years
Please insert the charging line to activate and
check whether the display low battery and need
to be charge
1) When it is not connected and no operation, the
screen will turn o in 1 minute, it will automatically
shutdown in 20 minutes, and the power indicator
will turn o.
2) After the screen is turned o, click once to
activate the screen display state. In any mode, long
press for 5 seconds to start the machine and long
press for 10 seconds to shut down the machine
Automatic
sleep function
Automatic
shutdown after
startup
4
3
5
Product Specification
Name
Products No.
Telephone No.
Address
Date
Sales Store
Store Stamp
Warranty Card
Usage and storage environment
After Sales Service
Operating environment
Storage environment
Operating ambient temperature--- -20℃--- +45℃
Humidity of working environment --- 20%---80%RH
Storage ambient temperature --- -20℃--- +55℃
Humidity of storage environment --- 20%---90%RH
With the purchase receipt, the warranty period is one year for the
quality issue. The following cases; but not limit to; are not covered
by the warranty:
Damage cause by unauthorized disassembly, repair,water/liquid
damage, misuse, abuse, modication, accident and negligence.
Damage cause by user misuse or fall.
Damage cause by improper operation and failure to carry out
suggested maintenance.
Repair work not covered by the warranty will be charged based
on the damage condition.
The manufacturer has the sole right on making the nal decision
on the warranty coverage.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:(1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Any Changes or modications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure
condition without restriction.
FCC Warning
3GJKOT)NOTG
Note:
1. App binding function:
considering the security of
personal sports data, each
dumbbell device can only bind
one mobile app account. When
account a binds the dumbbell
electronic module, account B cannot bind the electronic module
without unbinding. If the user forgets his account number and
cannot log in, he can press the reset button on the back of the
electronic module to restore the factory settings. Long press for
10 seconds to restore, and the module will shut down
automatically. After that, the user needs to long press 5 seconds
to start up. At this time, the binding of the previous account can
be released.
2. Normal unbinding method of account: in the app bound device
screen, select the bound device need to be delete, and then click
delete.
3. Reset function: there is a reset button on the back of the
electronic module to restore the factory settings.
History record: Dumbbell
data will be automatically
saved in the APP for your
reference
Troubleshooting
When the display cannot be turned on after it
is turned o, the screen does not display.
Please use the charging cable to activate the
device. After the screen is displayed, it can be
use normally.
Please remove the module from the dumbbell
handle, press the key on the back of the
module for 10 seconds and release it. At the
same time, you can see that the electronic
module is turned o and the system enters
reset. At this time, touch the icon at the corner
to restart it
Charging
Plug
Input
Voltage
Input
Current
Battery
Capacity
Charging
Time
Charging Indicator
Light Status
Micro-
USB 2.0 4.75-5.25V 0.5~0.8A 120mAh 1~2H
Solution
Problem description
Item
When the machine
is turn on, the
screen is displayed,
but there is no
response when
operating the
touch screen
Unable to boot or
crash handling
method
Please note that the Bluetooth icon displayed
on the page is blue, and the dumbbell has been
successfully connected to the mobile phone
app. If the oine icon is displayed, it indicates
that the dumbbell has not been successfully
connected.
If it is displayed as oine:
1. Please check whether the dumbbell is on;
2. Check whether the Bluetooth on the phone is
turned on;
3. Pull down and refresh the page, and check
whether the connection is successful after 2
seconds;
Dumbbells have
been added to the
app page, but the
icon shows oine
and cannot be
connect with
dumbbell
1
2
Charging Specification
White LED
on: 15% or above，
Red Light on: Below
15%, please
re-charge
Product Name:
Bluetooth Version
Bluetooth Distance
Handle Size
Material
Product Weight
Display
Battery Spec.
Standby Time
Standby Maintenance
Battery Life
Smart Dumbbell
Bluetooth 5.0
10 meters
245.42 X 70.7mm
ABS+PC, Metal & EVA
Around 4 KG
Nixie tube display
Lion Battery 3.7V/120mAh
Around 10 hours
Recommend re-charge every 3months
3 Years
Please insert the charging line to activate and
check whether the display low battery and need
to be charge
1) When it is not connected and no operation, the
screen will turn o in 1 minute, it will automatically
shutdown in 20 minutes, and the power indicator
will turn o.
2) After the screen is turned o, click once to
activate the screen display state. In any mode, long
press for 5 seconds to start the machine and long
press for 10 seconds to shut down the machine
Automatic
sleep function
Automatic
shutdown after
startup
4
3
5
Product Specification
Name
Products No.
Telephone No.
Address
Date
Sales Store
Store Stamp
Warranty Card
Usage and storage environment
After Sales Service
Operating environment
Storage environment
Operating ambient temperature--- -20℃--- +45℃
Humidity of working environment --- 20%---80%RH
Storage ambient temperature --- -20℃--- +55℃
Humidity of storage environment --- 20%---90%RH
With the purchase receipt, the warranty period is one year for the
quality issue. The following cases; but not limit to; are not covered
by the warranty:
Damage cause by unauthorized disassembly, repair,water/liquid
damage, misuse, abuse, modication, accident and negligence.
Damage cause by user misuse or fall.
Damage cause by improper operation and failure to carry out
suggested maintenance.
Repair work not covered by the warranty will be charged based
on the damage condition.
The manufacturer has the sole right on making the nal decision
on the warranty coverage.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:(1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Any Changes or modications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure
condition without restriction.
FCC Warning
3GJKOT)NOTG
Note:
1. App binding function:
considering the security of
personal sports data, each
dumbbell device can only bind
one mobile app account. When
account a binds the dumbbell
electronic module, account B cannot bind the electronic module
without unbinding. If the user forgets his account number and
cannot log in, he can press the reset button on the back of the
electronic module to restore the factory settings. Long press for
10 seconds to restore, and the module will shut down
automatically. After that, the user needs to long press 5 seconds
to start up. At this time, the binding of the previous account can
be released.
2. Normal unbinding method of account: in the app bound device
screen, select the bound device need to be delete, and then click
delete.
3. Reset function: there is a reset button on the back of the
electronic module to restore the factory settings.
History record: Dumbbell
data will be automatically
saved in the APP for your
reference
Troubleshooting
When the display cannot be turned on after it
is turned o, the screen does not display.
Please use the charging cable to activate the
device. After the screen is displayed, it can be
use normally.
Please remove the module from the dumbbell
handle, press the key on the back of the
module for 10 seconds and release it. At the
same time, you can see that the electronic
module is turned o and the system enters
reset. At this time, touch the icon at the corner
to restart it
Charging
Plug
Input
Voltage
Input
Current
Battery
Capacity
Charging
Time
Charging Indicator
Light Status
Micro-
USB 2.0 4.75-5.25V 0.5~0.8A 120mAh 1~2H
Solution
Problem description
Item
When the machine
is turn on, the
screen is displayed,
but there is no
response when
operating the
touch screen
Unable to boot or
crash handling
method
Please note that the Bluetooth icon displayed
on the page is blue, and the dumbbell has been
successfully connected to the mobile phone
app. If the oine icon is displayed, it indicates
that the dumbbell has not been successfully
connected.
If it is displayed as oine:
1. Please check whether the dumbbell is on;
2. Check whether the Bluetooth on the phone is
turned on;
3. Pull down and refresh the page, and check
whether the connection is successful after 2
seconds;
Dumbbells have
been added to the
app page, but the
icon shows oine
and cannot be
connect with
dumbbell
1
2
Charging Specification
White LED
on: 15% or above，
Red Light on: Below
15%, please
re-charge
Product Name:
Bluetooth Version
Bluetooth Distance
Handle Size
Material
Product Weight
Display
Battery Spec.
Standby Time
Standby Maintenance
Battery Life
Smart Dumbbell
Bluetooth 5.0
10 meters
245.42 X 70.7mm
ABS+PC, Metal & EVA
Around 4 KG
Nixie tube display
Lion Battery 3.7V/120mAh
Around 10 hours
Recommend re-charge every 3months
3 Years
Please insert the charging line to activate and
check whether the display low battery and need
to be charge
1) When it is not connected and no operation, the
screen will turn o in 1 minute, it will automatically
shutdown in 20 minutes, and the power indicator
will turn o.
2) After the screen is turned o, click once to
activate the screen display state. In any mode, long
press for 5 seconds to start the machine and long
press for 10 seconds to shut down the machine
Automatic
sleep function
Automatic
shutdown after
startup
4
3
5
Product Specification
Name
Products No.
Telephone No.
Address
Date
Sales Store
Store Stamp
Warranty Card
Usage and storage environment
After Sales Service
Operating environment
Storage environment
Operating ambient temperature--- -20℃--- +45℃
Humidity of working environment --- 20%---80%RH
Storage ambient temperature --- -20℃--- +55℃
Humidity of storage environment --- 20%---90%RH
With the purchase receipt, the warranty period is one year for the
quality issue. The following cases; but not limit to; are not covered
by the warranty:
Damage cause by unauthorized disassembly, repair,water/liquid
damage, misuse, abuse, modication, accident and negligence.
Damage cause by user misuse or fall.
Damage cause by improper operation and failure to carry out
suggested maintenance.
Repair work not covered by the warranty will be charged based
on the damage condition.
The manufacturer has the sole right on making the nal decision
on the warranty coverage.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:(1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Any Changes or modications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure
condition without restriction.
FCC Warning
3GJKOT)NOTG
Note:
1. App binding function:
considering the security of
personal sports data, each
dumbbell device can only bind
one mobile app account. When
account a binds the dumbbell
electronic module, account B cannot bind the electronic module
without unbinding. If the user forgets his account number and
cannot log in, he can press the reset button on the back of the
electronic module to restore the factory settings. Long press for
10 seconds to restore, and the module will shut down
automatically. After that, the user needs to long press 5 seconds
to start up. At this time, the binding of the previous account can
be released.
2. Normal unbinding method of account: in the app bound device
screen, select the bound device need to be delete, and then click
delete.
3. Reset function: there is a reset button on the back of the
electronic module to restore the factory settings.
History record: Dumbbell
data will be automatically
saved in the APP for your
reference
Troubleshooting
When the display cannot be turned on after it
is turned o, the screen does not display.
Please use the charging cable to activate the
device. After the screen is displayed, it can be
use normally.
Please remove the module from the dumbbell
handle, press the key on the back of the
module for 10 seconds and release it. At the
same time, you can see that the electronic
module is turned o and the system enters
reset. At this time, touch the icon at the corner
to restart it
Charging
Plug
Input
Voltage
Input
Current
Battery
Capacity
Charging
Time
Charging Indicator
Light Status
Micro-
USB 2.0 4.75-5.25V 0.5~0.8A 120mAh 1~2H
Solution
Problem description
Item
When the machine
is turn on, the
screen is displayed,
but there is no
response when
operating the
touch screen
Unable to boot or
crash handling
method
Please note that the Bluetooth icon displayed
on the page is blue, and the dumbbell has been
successfully connected to the mobile phone
app. If the oine icon is displayed, it indicates
that the dumbbell has not been successfully
connected.
If it is displayed as oine:
1. Please check whether the dumbbell is on;
2. Check whether the Bluetooth on the phone is
turned on;
3. Pull down and refresh the page, and check
whether the connection is successful after 2
seconds;
Dumbbells have
been added to the
app page, but the
icon shows oine
and cannot be
connect with
dumbbell
1
2
Charging Specification
White LED
on: 15% or above，
Red Light on: Below
15%, please
re-charge
Product Name:
Bluetooth Version
Bluetooth Distance
Handle Size
Material
Product Weight
Display
Battery Spec.
Standby Time
Standby Maintenance
Battery Life
Smart Dumbbell
Bluetooth 5.0
10 meters
245.42 X 70.7mm
ABS+PC, Metal & EVA
Around 4 KG
Nixie tube display
Lion Battery 3.7V/120mAh
Around 10 hours
Recommend re-charge every 3months
3 Years
Please insert the charging line to activate and
check whether the display low battery and need
to be charge
1) When it is not connected and no operation, the
screen will turn o in 1 minute, it will automatically
shutdown in 20 minutes, and the power indicator
will turn o.
2) After the screen is turned o, click once to
activate the screen display state. In any mode, long
press for 5 seconds to start the machine and long
press for 10 seconds to shut down the machine
Automatic
sleep function
Automatic
shutdown after
startup
4
3
5
Product Specification
Name
Products No.
Telephone No.
Address
Date
Sales Store
Store Stamp
Warranty Card
Usage and storage environment
After Sales Service
Operating environment
Storage environment
Operating ambient temperature--- -20℃--- +45℃
Humidity of working environment --- 20%---80%RH
Storage ambient temperature --- -20℃--- +55℃
Humidity of storage environment --- 20%---90%RH
With the purchase receipt, the warranty period is one year for the
quality issue. The following cases; but not limit to; are not covered
by the warranty:
Damage cause by unauthorized disassembly, repair,water/liquid
damage, misuse, abuse, modication, accident and negligence.
Damage cause by user misuse or fall.
Damage cause by improper operation and failure to carry out
suggested maintenance.
Repair work not covered by the warranty will be charged based
on the damage condition.
The manufacturer has the sole right on making the nal decision
on the warranty coverage.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:(1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Any Changes or modications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure
condition without restriction.
FCC Warning
3GJKOT)NOTG
Note:
1. App binding function:
considering the security of
personal sports data, each
dumbbell device can only bind
one mobile app account. When
account a binds the dumbbell
electronic module, account B cannot bind the electronic module
without unbinding. If the user forgets his account number and
cannot log in, he can press the reset button on the back of the
electronic module to restore the factory settings. Long press for
10 seconds to restore, and the module will shut down
automatically. After that, the user needs to long press 5 seconds
to start up. At this time, the binding of the previous account can
be released.
2. Normal unbinding method of account: in the app bound device
screen, select the bound device need to be delete, and then click
delete.
3. Reset function: there is a reset button on the back of the
electronic module to restore the factory settings.
History record: Dumbbell
data will be automatically
saved in the APP for your
reference
Troubleshooting
When the display cannot be turned on after it
is turned o, the screen does not display.
Please use the charging cable to activate the
device. After the screen is displayed, it can be
use normally.
Please remove the module from the dumbbell
handle, press the key on the back of the
module for 10 seconds and release it. At the
same time, you can see that the electronic
module is turned o and the system enters
reset. At this time, touch the icon at the corner
to restart it
Charging
Plug
Input
Voltage
Input
Current
Battery
Capacity
Charging
Time
Charging Indicator
Light Status
Micro-
USB 2.0 4.75-5.25V 0.5~0.8A 120mAh 1~2H
Solution
Problem description
Item
When the machine
is turn on, the
screen is displayed,
but there is no
response when
operating the
touch screen
Unable to boot or
crash handling
method
Please note that the Bluetooth icon displayed
on the page is blue, and the dumbbell has been
successfully connected to the mobile phone
app. If the oine icon is displayed, it indicates
that the dumbbell has not been successfully
connected.
If it is displayed as oine:
1. Please check whether the dumbbell is on;
2. Check whether the Bluetooth on the phone is
turned on;
3. Pull down and refresh the page, and check
whether the connection is successful after 2
seconds;
Dumbbells have
been added to the
app page, but the
icon shows oine
and cannot be
connect with
dumbbell
1
2
Charging Specification
White LED
on: 15% or above，
Red Light on: Below
15%, please
re-charge
Product Name:
Bluetooth Version
Bluetooth Distance
Handle Size
Material
Product Weight
Display
Battery Spec.
Standby Time
Standby Maintenance
Battery Life
Smart Dumbbell
Bluetooth 5.0
10 meters
245.42 X 70.7mm
ABS+PC, Metal & EVA
Around 4 KG
Nixie tube display
Lion Battery 3.7V/120mAh
Around 10 hours
Recommend re-charge every 3months
3 Years
Please insert the charging line to activate and
check whether the display low battery and need
to be charge
1) When it is not connected and no operation, the
screen will turn o in 1 minute, it will automatically
shutdown in 20 minutes, and the power indicator
will turn o.
2) After the screen is turned o, click once to
activate the screen display state. In any mode, long
press for 5 seconds to start the machine and long
press for 10 seconds to shut down the machine
Automatic
sleep function
Automatic
shutdown after
startup
4
3
5
Product Specification
Name
Products No.
Telephone No.
Address
Date
Sales Store
Store Stamp
Warranty Card
Usage and storage environment
After Sales Service
Operating environment
Storage environment
Operating ambient temperature--- -20℃--- +45℃
Humidity of working environment --- 20%---80%RH
Storage ambient temperature --- -20℃--- +55℃
Humidity of storage environment --- 20%---90%RH
With the purchase receipt, the warranty period is one year for the
quality issue. The following cases; but not limit to; are not covered
by the warranty:
Damage cause by unauthorized disassembly, repair,water/liquid
damage, misuse, abuse, modication, accident and negligence.
Damage cause by user misuse or fall.
Damage cause by improper operation and failure to carry out
suggested maintenance.
Repair work not covered by the warranty will be charged based
on the damage condition.
The manufacturer has the sole right on making the nal decision
on the warranty coverage.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:(1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Any Changes or modications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure
condition without restriction.
FCC Warning
3GJKOT)NOTG
Note:
1. App binding function:
considering the security of
personal sports data, each
dumbbell device can only bind
one mobile app account. When
account a binds the dumbbell
electronic module, account B cannot bind the electronic module
without unbinding. If the user forgets his account number and
cannot log in, he can press the reset button on the back of the
electronic module to restore the factory settings. Long press for
10 seconds to restore, and the module will shut down
automatically. After that, the user needs to long press 5 seconds
to start up. At this time, the binding of the previous account can
be released.
2. Normal unbinding method of account: in the app bound device
screen, select the bound device need to be delete, and then click
delete.
3. Reset function: there is a reset button on the back of the
electronic module to restore the factory settings.
History record: Dumbbell
data will be automatically
saved in the APP for your
reference
Troubleshooting
When the display cannot be turned on after it
is turned o, the screen does not display.
Please use the charging cable to activate the
device. After the screen is displayed, it can be
use normally.
Please remove the module from the dumbbell
handle, press the key on the back of the
module for 10 seconds and release it. At the
same time, you can see that the electronic
module is turned o and the system enters
reset. At this time, touch the icon at the corner
to restart it
Charging
Plug
Input
Voltage
Input
Current
Battery
Capacity
Charging
Time
Charging Indicator
Light Status
Micro-
USB 2.0 4.75-5.25V 0.5~0.8A 120mAh 1~2H
Solution
Problem description
Item
When the machine
is turn on, the
screen is displayed,
but there is no
response when
operating the
touch screen
Unable to boot or
crash handling
method
Please note that the Bluetooth icon displayed
on the page is blue, and the dumbbell has been
successfully connected to the mobile phone
app. If the oine icon is displayed, it indicates
that the dumbbell has not been successfully
connected.
If it is displayed as oine:
1. Please check whether the dumbbell is on;
2. Check whether the Bluetooth on the phone is
turned on;
3. Pull down and refresh the page, and check
whether the connection is successful after 2
seconds;
Dumbbells have
been added to the
app page, but the
icon shows oine
and cannot be
connect with
dumbbell
1
2
Charging Specification
White LED
on: 15% or above，
Red Light on: Below
15%, please
re-charge
Product Name:
Bluetooth Version
Bluetooth Distance
Handle Size
Material
Product Weight
Display
Battery Spec.
Standby Time
Standby Maintenance
Battery Life
Smart Dumbbell
Bluetooth 5.0
10 meters
245.42 X 70.7mm
ABS+PC, Metal & EVA
Around 4 KG
Nixie tube display
Lion Battery 3.7V/120mAh
Around 10 hours
Recommend re-charge every 3months
3 Years
Please insert the charging line to activate and
check whether the display low battery and need
to be charge
1) When it is not connected and no operation, the
screen will turn o in 1 minute, it will automatically
shutdown in 20 minutes, and the power indicator
will turn o.
2) After the screen is turned o, click once to
activate the screen display state. In any mode, long
press for 5 seconds to start the machine and long
press for 10 seconds to shut down the machine
Automatic
sleep function
Automatic
shutdown after
startup
4
3
5
Product Specification
Name
Products No.
Telephone No.
Address
Date
Sales Store
Store Stamp
Warranty Card
Usage and storage environment
After Sales Service
Operating environment
Storage environment
Operating ambient temperature--- -20℃--- +45℃
Humidity of working environment --- 20%---80%RH
Storage ambient temperature --- -20℃--- +55℃
Humidity of storage environment --- 20%---90%RH
With the purchase receipt, the warranty period is one year for the
quality issue. The following cases; but not limit to; are not covered
by the warranty:
Damage cause by unauthorized disassembly, repair,water/liquid
damage, misuse, abuse, modication, accident and negligence.
Damage cause by user misuse or fall.
Damage cause by improper operation and failure to carry out
suggested maintenance.
Repair work not covered by the warranty will be charged based
on the damage condition.
The manufacturer has the sole right on making the nal decision
on the warranty coverage.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:(1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Any Changes or modications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure
condition without restriction.
FCC Warning
3GJKOT)NOTG
Note:
1. App binding function:
considering the security of
personal sports data, each
dumbbell device can only bind
one mobile app account. When
account a binds the dumbbell
electronic module, account B cannot bind the electronic module
without unbinding. If the user forgets his account number and
cannot log in, he can press the reset button on the back of the
electronic module to restore the factory settings. Long press for
10 seconds to restore, and the module will shut down
automatically. After that, the user needs to long press 5 seconds
to start up. At this time, the binding of the previous account can
be released.
2. Normal unbinding method of account: in the app bound device
screen, select the bound device need to be delete, and then click
delete.
3. Reset function: there is a reset button on the back of the
electronic module to restore the factory settings.
History record: Dumbbell
data will be automatically
saved in the APP for your
reference
Troubleshooting
When the display cannot be turned on after it
is turned o, the screen does not display.
Please use the charging cable to activate the
device. After the screen is displayed, it can be
use normally.
Please remove the module from the dumbbell
handle, press the key on the back of the
module for 10 seconds and release it. At the
same time, you can see that the electronic
module is turned o and the system enters
reset. At this time, touch the icon at the corner
to restart it
Charging
Plug
Input
Voltage
Input
Current
Battery
Capacity
Charging
Time
Charging Indicator
Light Status
Micro-
USB 2.0 4.75-5.25V 0.5~0.8A 120mAh 1~2H
Solution
Problem description
Item
When the machine
is turn on, the
screen is displayed,
but there is no
response when
operating the
touch screen
Unable to boot or
crash handling
method
Please note that the Bluetooth icon displayed
on the page is blue, and the dumbbell has been
successfully connected to the mobile phone
app. If the oine icon is displayed, it indicates
that the dumbbell has not been successfully
connected.
If it is displayed as oine:
1. Please check whether the dumbbell is on;
2. Check whether the Bluetooth on the phone is
turned on;
3. Pull down and refresh the page, and check
whether the connection is successful after 2
seconds;
Dumbbells have
been added to the
app page, but the
icon shows oine
and cannot be
connect with
dumbbell
1
2
Charging Specification
White LED
on: 15% or above，
Red Light on: Below
15%, please
re-charge
Product Name:
Bluetooth Version
Bluetooth Distance
Handle Size
Material
Product Weight
Display
Battery Spec.
Standby Time
Standby Maintenance
Battery Life
Smart Dumbbell
Bluetooth 5.0
10 meters
245.42 X 70.7mm
ABS+PC, Metal & EVA
Around 4 KG
Nixie tube display
Lion Battery 3.7V/120mAh
Around 10 hours
Recommend re-charge every 3months
3 Years
Please insert the charging line to activate and
check whether the display low battery and need
to be charge
1) When it is not connected and no operation, the
screen will turn o in 1 minute, it will automatically
shutdown in 20 minutes, and the power indicator
will turn o.
2) After the screen is turned o, click once to
activate the screen display state. In any mode, long
press for 5 seconds to start the machine and long
press for 10 seconds to shut down the machine
Automatic
sleep function
Automatic
shutdown after
startup
4
3
5
Product Specification
Name
Products No.
Telephone No.
Address
Date
Sales Store
Store Stamp
Warranty Card
Usage and storage environment
After Sales Service
Operating environment
Storage environment
Operating ambient temperature--- -20℃--- +45℃
Humidity of working environment --- 20%---80%RH
Storage ambient temperature --- -20℃--- +55℃
Humidity of storage environment --- 20%---90%RH
With the purchase receipt, the warranty period is one year for the
quality issue. The following cases; but not limit to; are not covered
by the warranty:
Damage cause by unauthorized disassembly, repair,water/liquid
damage, misuse, abuse, modication, accident and negligence.
Damage cause by user misuse or fall.
Damage cause by improper operation and failure to carry out
suggested maintenance.
Repair work not covered by the warranty will be charged based
on the damage condition.
The manufacturer has the sole right on making the nal decision
on the warranty coverage.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:(1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Any Changes or modications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure
condition without restriction.
FCC Warning
3GJKOT)NOTG
Note:
1. App binding function:
considering the security of
personal sports data, each
dumbbell device can only bind
one mobile app account. When
account a binds the dumbbell
electronic module, account B cannot bind the electronic module
without unbinding. If the user forgets his account number and
cannot log in, he can press the reset button on the back of the
electronic module to restore the factory settings. Long press for
10 seconds to restore, and the module will shut down
automatically. After that, the user needs to long press 5 seconds
to start up. At this time, the binding of the previous account can
be released.
2. Normal unbinding method of account: in the app bound device
screen, select the bound device need to be delete, and then click
delete.
3. Reset function: there is a reset button on the back of the
electronic module to restore the factory settings.
History record: Dumbbell
data will be automatically
saved in the APP for your
reference
Troubleshooting
When the display cannot be turned on after it
is turned o, the screen does not display.
Please use the charging cable to activate the
device. After the screen is displayed, it can be
use normally.
Please remove the module from the dumbbell
handle, press the key on the back of the
module for 10 seconds and release it. At the
same time, you can see that the electronic
module is turned o and the system enters
reset. At this time, touch the icon at the corner
to restart it
Charging
Plug
Input
Voltage
Input
Current
Battery
Capacity
Charging
Time
Charging Indicator
Light Status
Micro-
USB 2.0 4.75-5.25V 0.5~0.8A 120mAh 1~2H
Solution
Problem description
Item
When the machine
is turn on, the
screen is displayed,
but there is no
response when
operating the
touch screen
Unable to boot or
crash handling
method
Please note that the Bluetooth icon displayed
on the page is blue, and the dumbbell has been
successfully connected to the mobile phone
app. If the oine icon is displayed, it indicates
that the dumbbell has not been successfully
connected.
If it is displayed as oine:
1. Please check whether the dumbbell is on;
2. Check whether the Bluetooth on the phone is
turned on;
3. Pull down and refresh the page, and check
whether the connection is successful after 2
seconds;
Dumbbells have
been added to the
app page, but the
icon shows oine
and cannot be
connect with
dumbbell
1
2
Charging Specification
White LED
on: 15% or above，
Red Light on: Below
15%, please
re-charge
Product Name:
Bluetooth Version
Bluetooth Distance
Handle Size
Material
Product Weight
Display
Battery Spec.
Standby Time
Standby Maintenance
Battery Life
Smart Dumbbell
Bluetooth 5.0
10 meters
245.42 X 70.7mm
ABS+PC, Metal & EVA
Around 4 KG
Nixie tube display
Lion Battery 3.7V/120mAh
Around 10 hours
Recommend re-charge every 3months
3 Years
Please insert the charging line to activate and
check whether the display low battery and need
to be charge
1) When it is not connected and no operation, the
screen will turn o in 1 minute, it will automatically
shutdown in 20 minutes, and the power indicator
will turn o.
2) After the screen is turned o, click once to
activate the screen display state. In any mode, long
press for 5 seconds to start the machine and long
press for 10 seconds to shut down the machine
Automatic
sleep function
Automatic
shutdown after
startup
4
3
5
Product Specification
Name
Products No.
Telephone No.
Address
Date
Sales Store
Store Stamp
Warranty Card
Usage and storage environment
After Sales Service
Operating environment
Storage environment
Operating ambient temperature--- -20℃--- +45℃
Humidity of working environment --- 20%---80%RH
Storage ambient temperature --- -20℃--- +55℃
Humidity of storage environment --- 20%---90%RH
With the purchase receipt, the warranty period is one year for the
quality issue. The following cases; but not limit to; are not covered
by the warranty:
Damage cause by unauthorized disassembly, repair,water/liquid
damage, misuse, abuse, modication, accident and negligence.
Damage cause by user misuse or fall.
Damage cause by improper operation and failure to carry out
suggested maintenance.
Repair work not covered by the warranty will be charged based
on the damage condition.
The manufacturer has the sole right on making the nal decision
on the warranty coverage.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:(1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Any Changes or modications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure
condition without restriction.
Table of contents
