Pioneer sc-lx87 User manual

Operating Instructions
AV Receiver SC-LX77
SC-LX87

2
WARNING
This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.
D3-4-2-1-3_A1_En
WARNING
To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 20 cm at top, 10 cm at rear, and 20 cm at each
side).
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.
D3-4-2-1-7b*_A1_En
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light)
D3-4-2-1-7c*_A1_En
CAUTION
The STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from the
AC outlet to shut down all power. Therefore, make
sure the unit has been installed so that the power
cord can be easily unplugged from the AC outlet in
case of an accident. To avoid fire hazard, the power
cord should also be unplugged from the AC outlet
when left unused for a long period of time (for
example, when on vacation).
D3-4-2-2-2a*_A1_En
CAUTION
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL. D3-4-2-1-1_B1_En
WARNING
Store small parts out of the reach of children and
infants. If accidentally swallowed, contact a doctor
immediately.
D41-6-4_A1_En
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
period.
K041_A1_En
Medium size
screwdriver
220 - 230 V
240 V
VOLTAGE
SELECTOR
D3-4-2-1-5*_A2_En
Voltage selector
You can find the voltage selector switch on the rear
panel of multi-voltage models.
The factory setting for the voltage selector is
220-230 V. Please set it to the correct voltage for
your country or region.
Before changing the voltage, disconnect the AC
power cord. Use a medium size screwdriver to
change the voltage selector switch.

3
Thank you for buying this Pioneer product. Please read through these operating instruc-
tions so you will know how to operate your model properly.
Contents
01 Before you start
Checking what’s in the box................................................................................................................................................7
Notice in regards to the separately sold Bluetooth ADAPTER and wireless LAN converter .......................................7
Our philosophy....................................................................................................................................................................7
Features............................................................................................................................................................................... 7
Installing the receiver.........................................................................................................................................................9
Loading the batteries..........................................................................................................................................................9
Operating range of remote control unit............................................................................................................................9
About using AVNavigator (included CD-ROM)................................................................................................................9
02 Controls and displays
Remote control .................................................................................................................................................................12
Display ...............................................................................................................................................................................14
Front panel ........................................................................................................................................................................15
03 Connecting your equipment
Connecting your equipment............................................................................................................................................17
Rear panel .........................................................................................................................................................................17
Determining the speakers’ application ..........................................................................................................................18
Placing the speakers........................................................................................................................................................21
Connecting the speakers.................................................................................................................................................21
Installing your speaker system........................................................................................................................................23
About the audio connection ............................................................................................................................................28
About the video converter................................................................................................................................................29
About HDMI ......................................................................................................................................................................29
Connecting your TV and playback components ............................................................................................................30
Connecting an HDD/DVD recorder, BD recorder and other video sources ...............................................................32
Connecting a satellite/cable receiver or other set-top box ...........................................................................................33
Connecting other audio components.............................................................................................................................34
Connecting additional amplifiers....................................................................................................................................35
Connecting the multichannel analog inputs .................................................................................................................35
Connecting AM/FM antennas.........................................................................................................................................36
MULTI-ZONE setup...........................................................................................................................................................37
Connecting to the network through LAN interface .......................................................................................................39
Connecting optional Bluetooth ADAPTER .....................................................................................................................40
Connecting an iPod..........................................................................................................................................................40
Connecting a USB device ................................................................................................................................................41
Connecting an MHL-compatible device.........................................................................................................................41
Connecting an HDMI-equipped component to the front panel input .........................................................................41
Using a USB cable to connect to a computer ...............................................................................................................41
Connecting to a wireless LAN .........................................................................................................................................42
Connecting an IR receiver ...............................................................................................................................................42
Switching components on and off using the 12 volt trigger.........................................................................................43
Plugging in the receiver ...................................................................................................................................................43
04 Basic Setup
Automatically conducting optimum sound tuning (Full Auto MCACC) .....................................................................45
The Input Setup menu......................................................................................................................................................46
Operation Mode Setup.....................................................................................................................................................47
Changing the OSD display language (OSD Language)................................................................................................48
Changing the TV format setting ......................................................................................................................................48
Changing the frequency step ..........................................................................................................................................48
About the Home Menu.....................................................................................................................................................48
05 Basic playback
Playing a source ...............................................................................................................................................................50
Playing an iPod .................................................................................................................................................................51
Playing a USB device .......................................................................................................................................................52
Playing an MHL-compatible device ................................................................................................................................53
Playing music from a computer......................................................................................................................................54
Listening to the radio........................................................................................................................................................54
Bluetooth ADAPTER for Wireless Enjoyment of Music ................................................................................................55
06 Listening to your system
Enjoying various types of playback using the listening modes....................................................................................59
Selecting MCACC presets ...............................................................................................................................................61
Choosing the input signal................................................................................................................................................61
Better sound using Phase Control..................................................................................................................................62
Better sound using Phase Control and Full Band Phase Control ...............................................................................62
07 Playback with NETWORK features
Introduction.......................................................................................................................................................................65
Playback with Network functions....................................................................................................................................66
About network playback...................................................................................................................................................68
About playable file formats..............................................................................................................................................69
08 Control with HDMI function
About the Control with HDMI function...........................................................................................................................71
Making Control with HDMI connections........................................................................................................................71
HDMI Setup.......................................................................................................................................................................71
Before using synchronization..........................................................................................................................................72
About synchronized operations ......................................................................................................................................72
Setting the PQLS function ...............................................................................................................................................72
About Sound Retriever Link and Stream Smoother Link..............................................................................................72
Cautions on the Control with HDMI function ................................................................................................................73
09 Using other functions
Setting the Audio options ................................................................................................................................................75
Setting the Video options.................................................................................................................................................77
Switching the speaker terminals ....................................................................................................................................79
Using the MULTI-ZONE controls.....................................................................................................................................79
Making an audio or a video recording ............................................................................................................................80
Network settings from a web browser............................................................................................................................80
Using the sleep timer .......................................................................................................................................................81
Dimming the display ........................................................................................................................................................81
Switching the HDMI output.............................................................................................................................................81
Checking your system settings .......................................................................................................................................81
Resetting the system........................................................................................................................................................82

4
10 Controlling the rest of your system
About the Remote Setup menu.......................................................................................................................................84
Operating multiple receivers ...........................................................................................................................................84
Setting the remote to control other components ..........................................................................................................84
Selecting preset codes directly .......................................................................................................................................84
Programming signals from other remote controls .......................................................................................................85
Erasing one of the remote control button settings........................................................................................................85
Erasing all learnt settings that are in one input function .............................................................................................86
Direct function ..................................................................................................................................................................86
Setting the backlight mode .............................................................................................................................................86
About the ALL ZONE STBY (All Zone Standby) and DISCRETE ON (Discrete On) functions....................................86
Resetting the remote control settings............................................................................................................................87
Controlling components ..................................................................................................................................................87
11 The Advanced MCACC menu
Making receiver settings from the Advanced MCACC menu ......................................................................................91
Automatic MCACC (Expert).............................................................................................................................................91
Manual MCACC setup .....................................................................................................................................................93
Checking MCACC Data....................................................................................................................................................96
Data Management............................................................................................................................................................97
12 The System Setup and Other Setup menus
Making receiver settings from the System Setup menu...............................................................................................99
Manual speaker setup......................................................................................................................................................99
Network Setup menu .....................................................................................................................................................102
Checking the Network Information...............................................................................................................................103
The Other Setup menu...................................................................................................................................................103
MHL Setup ......................................................................................................................................................................106
Making network settings using Safari..........................................................................................................................107
Using Safari to set a friendly name...............................................................................................................................107
Using Safari to update the firmware.............................................................................................................................108
13 FAQ
Troubleshooting..............................................................................................................................................................110
Power...............................................................................................................................................................................110
No sound .........................................................................................................................................................................110
Other audio problems ....................................................................................................................................................111
ADAPTER PORT terminal ..............................................................................................................................................112
Video ................................................................................................................................................................................112
Settings............................................................................................................................................................................113
Professional Calibration EQ graphical output.............................................................................................................113
Display .............................................................................................................................................................................113
Remote control ...............................................................................................................................................................114
HDMI................................................................................................................................................................................114
MHL..................................................................................................................................................................................115
AVNavigator ....................................................................................................................................................................115
USB interface..................................................................................................................................................................116
iPod ..................................................................................................................................................................................116
Network ...........................................................................................................................................................................116
USB-DAC.........................................................................................................................................................................117
Web Control ....................................................................................................................................................................117
Wireless LAN...................................................................................................................................................................118
14 Additional information
Surround sound formats ...............................................................................................................................................120
About THX .......................................................................................................................................................................120
About HDMI ....................................................................................................................................................................121
HTC Connect...................................................................................................................................................................121
About iPod.......................................................................................................................................................................122
Windows 8.......................................................................................................................................................................122
MHL..................................................................................................................................................................................122
Software license notice..................................................................................................................................................122
Auto Surround, ALC and Stream Direct with different input signal formats............................................................123
Speaker Setting Guide....................................................................................................................................................123
About messages displayed when using network functions.......................................................................................124
Important information regarding the HDMI connection ............................................................................................125
Cleaning the unit ............................................................................................................................................................125
Pioneer Authorized Distributors ...................................................................................................................................125
Glossary ...........................................................................................................................................................................126
Features index.................................................................................................................................................................129
Specifications .................................................................................................................................................................130
Preset code list................................................................................................................................................................131

5
Flow of settings on the receiver
Flow for connecting and setting the receiver
The unit is a full-fledged AV receiver equipped with an abundance of functions and terminals. It can be used eas-
ily after following the procedure below to make the connections and settings.
Required setting item: 1, 2, 3, 4, 5, 7, 9
Setting to be made as necessary: 6, 8, 10, 11, 12, 13
Important
The receiver’s initial settings can be made on the computer using Wiring Navi on the AVNavigator CD-ROM
included with the receiver. In this case, virtually the same connections and settings as in steps 2, 3, 4, 5, 6, 7
and 8can be made interactively. For instructions on using AVNavigator, see About using AVNavigator (included
CD-ROM) on page 9.
1 Before you start
!Checking what’s in the box on page 7
!Loading the batteries on page 9
j
2 Determining the speakers’ application (page 18)
![A] 9.2 channel surround system (Front height/Front wide) connection
![B] 7.2 channel surround system & Speaker B connection
![C] 7.2 channel surround system & Front Bi-amping connection (High quality surround)
![D] 7.2 channel surround system (Surround back) & ZONE 2 connection (Multi Zone)
![E] 7.2 channel surround system (Front height/Front wide) & ZONE 2 connection (Multi Zone)
![F] 5.2 channel surround system & Front Bi-amping connection (High quality surround) & ZONE 2 connection
(Multi Zone)
![G-1] 5.2 channel surround system & ZONE 2/ZONE 3 connection (Multi Zone)
![G-2] Multi-ZONE Music
![H] 5.2 channel surround system & Speaker B Bi-amping connection
![I] 5.2 channel surround system & Front and Surround Bi-amping connection (High quality surround)
![J] 5.2 channel surround system & Front and Center Bi-amping connection (High quality surround)
![K] 5.2 channel surround system & Center and Surround Bi-amping connection (High quality surround)
j
3 Connecting the speakers
!Placing the speakers on page 21
!Connecting the speakers on page 21
!Installing your speaker system on page 23
!Bi-amping your speakers on page 22
j
4 Connecting the components
!About the audio connection on page 28
!About the video converter on page 29
!Connecting your TV and playback components on page 30
!Connecting AM/FM antennas on page 36
!Plugging in the receiver on page 43
j
5 Power On
j
6 Making the initial settings according to the region and environment in which you live
!Changing the TV format setting (page 48)
!Changing the frequency step (page 48)
!Changing the OSD display language (OSD Language) (page 48)
j
7 MCACC speaker settings
!Automatically conducting optimum sound tuning (Full Auto MCACC) on page 45
j
8 The Input Setup menu (page 46)
(When using connections other than the recommended connections)
j
9 Basic playback (page 49)
j
10 Switching the HDMI output (page 81)
j
11 Adjusting the sound and picture quality as desired
!Using the various listening modes (page 58)
!Better sound using Phase Control (page 62)
!Better sound using Phase Control and Full Band Phase Control (page 62)
!Measuring the all EQ type (SYMMETRY/ALL CH ADJ/FRONT ALIGN) (page 91)
!Changing the channel level while listening (page 100)
!Switching on/off the Acoustic Calibration EQ, Auto Sound Retriever or Dialog Enhancement (page 75)
!Setting the PQLS function (page 72)
!Setting the Audio options (page 75)
!Setting the Video options (page 77)
j
12 Other optional adjustments and settings
!Control with HDMI function (page 70)
!The Advanced MCACC menu (page 90)
!The System Setup and Other Setup menus (page 98)
j
13 Making maximum use of the remote control
!Operating multiple receivers (page 84)
!Setting the remote to control other components (page 84)

6
Checking what’s in the box ............................................................................................................7
Notice in regards to the separately sold Bluetooth ADAPTER and wireless LAN converter ..... 7
Our philosophy ................................................................................................................................7
Features............................................................................................................................................7
Installing the receiver...................................................................................................................... 9
Loading the batteries ...................................................................................................................... 9
Operating range of remote control unit........................................................................................ 9
About using AVNavigator (included CD-ROM) ............................................................................. 9
Before you start

7
01 Before you start
Checking what’s in the box
Please check that you’ve received the following supplied accessories:
!Setup microphone (cable: 5 m)
!Remote control unit
!AAA size IEC R03 dry cell batteries (to confirm system operation) x2
!AM loop antenna
!FM wire antenna
!Power cord
!CD-ROM (AVNavigator)
!Quick start guide
!Safety Brochure
Notice in regards to the separately sold Bluetooth ADAPTER and
wireless LAN converter
The countries/regions that adopted the optional products below, explained in the Operating instructions, are as
per the list.
Optional products Model No. Countries/regions that adopted the products
Bluetooth ADAPTER AS-BT100 Singapore, Malaysia, Thailand, Australia, New Zealand and Hong Kong
AS-BT200 Singapore, Malaysia, Thailand, Australia, New Zealand, Hong Kong and Taiwan
Wireless LAN Converter AS-WL300 Singapore, Malaysia, Thailand, Australia, New Zealand, Hong Kong and Taiwan
Our philosophy
Pioneer is dedicated to making your home theater listening experience as close as possible to the vision of the
moviemakers and mastering engineer when they created the original soundtrack. We do this by focusing on three
important steps:
1 Achieving the highest possible sound quality
2 Allowing for customized acoustic calibration according to any listening area
3 Fine-tuning the receiver with the help of world-class studio engineers
With the cooperation of AIR Studios, this receiver has been designated AIR Studios Monitor:
Features
%Class D Amplifier
This unit is an AV receiver developed based on the latest high performance Class D amplifier and integrating
the essence of Pioneer’s high sound quality designs. This new generation reference amplifier offers outstanding
performance with high sound quality and reproduces the latest in multi-channel digital contents.
%ESS-DAC-equipped
All channels are equipped with ESS SABRE 32 Ultra Audio DACs. The Jitter Eliminators achieve clearer sound.
%AIR Studios Sound Tuning
The SC-LX87 and SC-LX77 have received the AIR Studios Monitor certification. Pioneer has a proven track record
of applying its audio expertise to the creation of multi-channel sound environments. Established in 1969 in
London, AIR Studios is now an acclaimed recording complex, favoured by many of the world’s most popular and
renowned musical talents.
%THX Ultra 2 Plus
THX Ultra2 Plus is the highest level THX certification, featuring THX Loudness Plus technology, designed to main-
tain the impact and integrity of audio content even when played at lower volume settings. THX Ultra2 Plus helps
to deliver sound just as it was mixed in the studio, regardless of volume level.
%Audio Scaler
The combined effect of Hi-bit 32 Audio Processing, the digital filter and the up-sampling function can be used
to convert the signals of music files or CDs to up to 192 kHz/32 bits to achieve even clearer sound with higher
definition.
%Hi-Bit 32 Audio Processing
Creates a wider dynamic range with digital sources like CDs, DVDs or BDs. 16-, 20- and 24-bit PCM as well as
compressed audio is requantized to 32 bits, and the high frequency component is interpolated upon data pro-
cessing to enable smoother, more subtle musical expression.
%Auto Phase Control Plus
For discs created with standards other than Phase Control, the LFE channel is delayed upon recording in the first
place. This function automatically corrects for phase shifting on such discs and broadcast.
This function is particularly effective when playing multi-channel music containing low frequency effects (LFE).
%Full Band Phase Control (compatible with FRONT ALIGN)
The further advanced Full Band Phase Control technology focuses on the group delay in the speaker network
filter, and compensates with special digital signal processing (DSP), to adjust the phase of each unit as well as
the group delay for each speaker. Full Band Phase Control gives multi-range speakers the sound coherence of
full-range speakers, while retaining the wide frequency range advantage.
This is compatible with the FRONT ALIGN function for matching the characteristics of the speakers other than
the front speakers with those of the front speakers.
%PQLS Bit-stream
Jitterless high quality playback is possible by connecting a PQLS-compatible player with HDMI connections.
This feature is only available when the connected Pioneer Blu-ray Disc Player supporting the PQLS function.
%dts Neo:X compatible
This receiver supports the latest DTS processing format. The quality of Neo:X, originally designed for 9 channels
or more, can be enjoyed in a 7-channel environment.
%Various Speaker Channel Assign
With this receiver, 12 types of speaker systems, including bi-amp connections, can be assigned to achieve the
optimum speaker system for the user’s home theater environment and the speakers the user owns.
%Multi-Zone Music
All the speakers connected to this receiver in the main zone and all the sub zones can be played at once to enjoy
music contents.
%HDMI (3D, Audio Return Channel) - 9in/3out (Dual out + HDZONE out)
A compatible component is required to use the above function.
%Ultra HD (with 4K video support) – Pass-through and upscaling –
4K resolution images can be passed through and displayed as such, and the Hi-Vision or Full Hi-Vision images
of DVDs, Blu-ray discs and HD broadcasts can be upscaled to a resolution of up to 4K and displayed. A separate
monitor supporting Ultra HD (4K video) is required.

8
01 Before you start
%HDZONE output
This receiver supports output of the HDMI output to a subzone room. Powerful images can be enjoyed simply by
connected this receiver to a TV supporting 4K/Full-HD/3D. In addition, a multi-channel environment can be cre-
ated by connecting this receiver to another AV receiver in the subzone room.
%MHLTM (Mobile High-definition Link)-compatible device playback
An incorporates MHL 2 mobile device can be connected to enjoy 3D videos, full-HD videos, high quality multi-
channel audio, and photos etc., with charge the battery on the receiver.
%HTC Connect
HTC Connect makes it easy to wirelessly stream your favorite music straight from your HTC phone. There’s no
need for a separate app; HTC Connect is built right into your phone’s music player.
%USB-DAC (NATIVE DSD and LPCM transmission supported)
SC-LX87 only
Music files on a computer can be played by connecting the receiver with the computer using a commercially
available USB cable.
Files can be played with high sound quality when the exclusive driver is installed on the computer. The driver
software can be installed from the included CD-ROM (AVNavigator).
Native DSD playback by DoP (DSD over PCM) transmission is supported.
%DSD Music playback (via USB-DAC, Front USB and HDMI)
Playback of high sound quality DSD music (DSD files and DSD discs (SACDs)) is supported. With USB-DACs
(SC-LX87 only), USB devices and SACDs, DSD Direct playback bypassing the DSP circuitry is also possible.
%High Resolution Music Playback
High resolution music files with resolutions of 96 kHz/24 bit to 192 kHz/24 bit can be played. Playback of AIFF,
Apple Lossless, WAV and FLAC files via the front USB port and network is supported.
%Gapless Playback
The silent section between tracks is skipped when playing music files, eliminating the interruptions that usually
occur when playing live or concert contents.
%Apple AirPlay®
With AirPlay you can stream music from iTunes to the SC-LX87/SC-LX77 and play it through your home theater
system. You can even use the receiver to view metadata including song title, artist as well as album art on a con-
nected display. With Pioneer’s AirPlay-compatible receivers, you can easily enjoy your iTunes music in any room
in the house.
%iPod playback
Your iPod, iPhone or iPad can be connected to the receiver’s USB terminal and RCA video terminal to play the
music/video files on the iPod, iPhone or iPad.
Also, the iPod, iPhone or iPad is charged when it is connected to the receiver.
%Play ZONE
When playing music contents on smartphones or other terminals via the network, the zone in which the music is
to be played can be specified.
%Input Volume Absorber
Differences in the volume between inputs can be adjusted manually. If the volume seems different for certain
inputs, individual inputs can be adjusted to the user’s tastes by ±12 dB.
%Windows 8 Compatible
The AV receivers are compatible with Windows 8, letting you easily stream music from compatible PCs on your
home network.
%iControlAV2013 Remote Application
This is an application for smartphones and tablets allowing intuitive operation of many of the AV receiver’s func-
tions. Versions are available for iPhone, iPod touch, iPad and Android devices. The application can be down-
loaded free of charge from the App Store or Google Play.
%AVNavigator 2013 (for Windows PC, Macintosh and iPad)
The CD-ROM (AVNavigator) included with this unit provides a variety of functions, such as Wiring Navi with a
guide for connecting the unit and setting up from the computer and an Interactive Manual for operating the
unit while reading the manual.
Also, Operation Guide describes the receiver’s playback operations and how to use several functions through
videos and illustrations.
!The provided CD-ROM includes the Windows version of AVNavigator.
!Download the Mac OS version of AVNavigator from the Pioneer website (page 10).
!AVNavigator is available not only for Windows and Mac OS but also for iPad (downloadable free of charge). For
details, see http://pioneer.jp/product/soft/iapp_avnavi/en.html.
%Energy Saving Design
This AV receiver has an ecological design. In addition to even lower power consumption in standby, the receiver
is equipped with an “eco mode” for low power consumption when playing contents as well. Furthermore, the eco
mode can easily be set with a dedicated button on the remote control or using the application.
%Dolby Pro Logic llz compatible
Adding a pair of speakers above the front left and right speakers adds expressiveness in the vertical direction to
the previous horizontally-oriented sound field. The height channel strengthens the sound field’s sense of three-
dimensionality and air, producing presence and expansion.
%Virtual Speakers
By turning on “Virtual Surround Back”, “Virtual Height”, and “Virtual Wide” modes realize a maximum of 11.2
channels combining the actually installed speakers and the virtual speakers is possible. This makes for smoother
connection between the sounds and an improved 3D feel.
%Auto Sound Retriever
The Auto Sound Retriever feature employs DSP technology to restore sound pressure and smooth jagged arti-
facts left over after compression.
%Sound Retriever Link
By connecting a Pioneer player supporting the Sound Retriever Link function, compressed audio files played on
the player can be corrected automatically to play the sound with higher density.
This feature is only available when a Pioneer Blu-ray Disc player supporting this feature is connected.
%Stream Smoother Link
By connecting a Pioneer player supporting the Stream Smoother Link function, compressed video or movie files
played on the player can be corrected automatically to play them with a more natural, easily viewable picture.
This feature is only available when a Pioneer Blu-ray Disc player supporting this feature is connected.
%Internet Radio
By connecting this receiver to the network via the LAN terminal, you can listen to Internet radio stations.
%Bluetooth compatible
Using the Bluetooth ADAPTER (AS-BT100 or AS-BT200) lets you enjoy music files on an iPhone or other Bluetooth
wireless technology device wirelessly.
%Wireless LAN Converter Ready
With the AS-WL300 wireless LAN converter (Optional), you can enjoy wireless LAN connection for the AV receiv-
ers. The AS-WL300 works with power supply from the AV receiver’s dedicated USB terminal, so no AC adapter is
required.
%Easy setup using Advanced MCACC
The Auto MCACC Setup provides a quick but accurate surround sound setup, which includes the advanced fea-
tures of Professional Acoustic Calibration EQ.

9
01 Before you start
Installing the receiver
!When installing this unit, make sure to put it on a level and stable surface.
!Don’t install it on the following places:
—on a color TV (the screen may distort)
—near a cassette deck (or close to a device that gives off a magnetic field). This may interfere with the sound.
—in direct sunlight
—in damp or wet areas
—in extremely hot or cold areas
—in places where there is vibration or other movement
—in places that are very dusty
—in places that have hot fumes or oils (such as a kitchen)
!Do not touch this receiver’s bottom panel while the power is on or just after it is turned off. The bottom panel
becomes hot when the power is on (or right after it is turned off) and could cause burns.
Loading the batteries
The batteries included with the unit are to check initial operations; they may not last over a long period. We rec-
ommend using alkaline batteries that have a longer life.
WARNING
!Do not use or store batteries in direct sunlight or other excessively hot place, such as inside a car or near a
heater. This can cause batteries to leak, overheat, explode or catch fire. It can also reduce the life or perfor-
mance of batteries.
CAUTION
Incorrect use of batteries may result in such hazards as leakage and bursting. Observe the following precautions:
!Never use new and old batteries together.
!Insert the plus and minus sides of the batteries properly according to the marks in the battery case.
!When inserting the batteries, make sure not to damage the springs on the battery’s (–) terminals. This can
cause batteries to leak or overheat.
!Batteries with the same shape may have different voltages. Do not use different batteries together.
!When disposing of used batteries, please comply with governmental regulations or environmental public insti-
tution’s rules that apply in your country/area.
Operating range of remote control unit
The remote control may not work properly if:
!There are obstacles between the remote control and the receiver’s remote sensor.
!Direct sunlight or fluorescent light is shining onto the remote sensor.
!The receiver is located near a device that is emitting infrared rays.
!The receiver is operated simultaneously with another infrared remote control unit.
30°
30°
7 m
About using AVNavigator (included CD-ROM)
The included AVNavigator CD-ROM contains Wiring Navi allowing you to easily make the receiver’s connections
and initial settings in dialog fashion. High precision initial settings can be completed easily simply by following
the instructions on the screen to make the connections and settings.
There are also other features enabling easy use of various functions, including an Interactive Manual that oper-
ates in association with the receiver, updating of various types of software, and MCACC Application that lets you
check the MCACC measurement results on 3D graphs.
!Download the Mac OS version of AVNavigator from the Pioneer website (page 10).
!The iPad version of AVNavigator can be downloaded from the App Store.
!The provided CD-ROM includes the Windows version of AVNavigator.
Installing AVNavigator for Windows
1 Launch the desktop from the start screen (for Windows 8 only).
2 Load the included CD-ROM into your computer’s CD drive.
The CD-ROM’s top menu screen appears.
!A screen for selecting the CD-ROM’s operation (“Open with Explorer”, “Launch ‘MAIN_MENU.exe’”, etc.) may
be displayed. When the operation for launching “MAIN_MENU.exe” is performed, the AVNavigator menu
appears. A caution regarding security may appear during this operation, but there is no security problem, so
continue the operation.
!If the CD-ROM’s top menu screen is not displayed, double-click “MAIN_MENU.exe” on the CD-ROM. When
this is done, a caution regarding security is displayed, but there is no security problem, so continue the
operation.
3 Click “AVNavigator” on the “Installing Software” menu.
4 Follow the instructions on the screen to install.
When “Finish” is selected, installation is completed.
5 Remove the included CD-ROM from the computer’s CD drive.

10
01 Before you start
Handling the CD-ROM
Operating Environment
!AVNavigator can be used with Microsoft®Windows®XP/Windows Vista®/Windows®7/Windows®8.
!A browser is at times used for AVNavigator functions. The supported browser is Microsoft Internet Explorer®8,
9 or 10.
!Adobe®Flash®Player 10 must be installed to use some of the functions in AVNavigator.
For details, see http://www.adobe.com/downloads/.
Precautions For Use
!This CD-ROM is for use with a personal computer. It cannot be used with a DVD player or music CD player.
Attempting to play this CD-ROM with a DVD player or music CD player can damage speakers or cause
impaired hearing due to the large volume.
License
!Please agree to the “Terms of Use” indicated below before using this CD-ROM. Do not use if you are unwilling
to consent to the terms of its use.
Terms of Use
!Copyright to data provided on this CD-ROM belongs to PIONEER CORPORATION. Unauthorized transfer,
duplication, broadcast, public transmission, translation, sales, lending or other such matters that go beyond
the scope of “personal use” or “citation” as defined by Copyright Law may be subject to punitive actions.
Permission to use this CD-ROM is granted under license by PIONEER CORPORATION.
General Disclaimer
!PIONEER CORPORATION does not guarantee the operation of this CD-ROM with respect to personal com-
puters using any of the applicable OS. In addition, PIONEER CORPORATION is not liable for any damages
incurred as a result of use of this CD-ROM and is not responsible for any compensation. The names of private
corporations, products and other entities described herein are the registered trademarks or trademarks of their
respective firms.
Using AVNavigator for Windows
1 Click [AVNavigator 2013.V] on the desktop to launch AVNavigator.
AVNavigator is launched and Wiring Navi starts up. The language selection screen appears. Follow the instruc-
tions on the screen to make the connections and automatic settings.
Wiring Navi only starts up automatically the first time AVNavigator is launched.
2 Select and use the desired function.
AVNavigator includes the following functions:
!Wiring Navi – Guides you through connections and initial settings in dialog fashion. High precision initial
settings can be made easily.
!Operation Guide – Describes the receiver’s playback operations and how to use several functions through
videos and illustrations.
!Interactive Manual – Automatically displays the pages explaining the functions that have been operated on
the receiver. It is also possible to operate the receiver from the Interactive Manual.
!Glossary – Displays glossary pages.
!MCACC Appli – Displays Advanced MCACC measurement results vividly on the computer.
There are special operating instructions for MCACC Application. These instructions are included in the
AVNavigator Interactive Manual’s menus. Refer to them when using MCACC Application.
!Software Update – Allows various types of software to be updated.
!Settings – Used to make various AVNavigator settings.
!Detection – Used to detect the receiver. Press Detection before using the Interactive Manual,
MCACC Appli and Software Update to connect the receiver to the network.
Deleting the AVNavigator
You can use the following method to uninstall (delete) the AVNavigator from your PC.
%Delete from the Control Panel of the PC.
!With Windows XP/Windows Vista/Windows 7, AVNavigator can also be uninstalled using the following
operation.
From the Start menu, click “Program” d“PIONEER CORPORATION” d“AVNavigator 2013.V” d“Uninstall
AVNavigator 2013.V”.
Installing AVNavigator for Mac
1 Download “AVNavigator 2013.pkg” from one of the following websites:
!http://www.pioneer.com.sg (for Southeast Asia)
!http://www.pioneer.com.au (for Australia)
!http://www.pioneernz.co.nz (for New Zealand)
!http://www.pioneer-mea.com (for the Middle East and Africa)
!http://www.pioneer-india.in (for India)
!http://www.pioneer-latin.com (for Latin America)
2 Launch “AVNavigator 2013.pkg” from the “Downloads” folder.
3 Follow the instructions on the screen to install.
Operating Environment
!AVNavigator for Mac can be used with Mac OS X (10.7 or 10.8).
!A browser is at times used for AVNavigator for Mac functions. The supported browser is Safari 6.0.
Using AVNavigator for Mac
1 Launch “AVNavigator 2013”.
The file is located in the “Applications” folder just under the hard disk (Macintosh HD).
2 Select and use the desired function.
For details, see Using AVNavigator for Windows on page 10. The Mac OS version includes the same types of
functions.
Deleting the AVNavigator
You can use the following method to uninstall (delete) the AVNavigator from your Mac.
1 Delete “AVNavigator 2013”.
The file is located in the “Applications” folder just under the hard disk (Macintosh HD).
2 Delete the “jp.co.pioneer.AVNavigator 2013” folder.
The folder is located in the hard disk (Macintosh HD) d“Library” folder d“Application Support” folder.