Pioneer PRO-200 User manual

1. EXPLODED VIEWS AND PARTS LIST................2
2. CONTRAST OF MISCELLANEOUS PARTS......14
3. SCHEMATIC DIAGRAM.....................................20
4. PCB CONNECTION DIAGRAM..........................37
5. ADJUSTMENT....................................................49
6. IC INFORMATION..............................................62
7. BLOCK DIAGRAM..............................................66
CONTENTS
PRO-200
PROJECTION MONITOR RECEIVER
ORDER NO.
ARP2988
O - IZG JULY 1998 Printed in Japan
PIONEER ELECTRONIC CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER ELECTRONIC (EUROPE) N.V. Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 501 Orchard Road, #10-00 Wheelock Place, Singapore 238880
PIONEER ELECTRONIC CORPORATION 1998
PRO-100
c
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Type Model Power Requirement Remarks
PRO-200 PRO-100
KUXC/CA AC120V
Refer to the service manual ARP2936 for PRO-119 and PRO-99.

2
PRO-200, PRO-100
1. EXPLODED VIEWS AND PARTS LIST
NOTES: •Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
•The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
•Parts marked by are important parts which relate in X-rays radiation.
If any of these parts need to be replaced, always replace with specified parts.
•Screws adjacent to mark on the product are used for disassembly.
•For POWER SUPPLY ASSY, AWV1558 is used, but for serving, AWV1565 is supplied.
AWV1565 is the same as AWV1558 of which X-ray protection and high voltage sections have been adjusted and these
adjusted parts are covered with the shield cases. Therefor, AWV1565 need not be adjusted.
1.1 PACKING
31 ×12 (PRO-200)
31
×8 (PRO-100)
7
2
3
4
32 ×12 (PRO-200)
32
×8 (PRO-100)
7
35 34
8
9
26
28
29 30
27
10
11
15
19
20
21 33
2423
23
25
22
22 22
22
18
16 17 14
12,13
(Rear View)
PRO-100
PRO-100
PRO-200
PRO-200
1 (5,6)
24
22 22
25
33

3
PRO-200, PRO-100
Mark No. Symbol and Description Part No. Remarks
PRO-200/KUXC/CA PRO-100/KUXC/CA PRO-200/KUXC/CA PRO-100/KUXC/CA
1 Card Board Case (60) Card Board Case (51) AHB1154 AHB1152
NSP 5 Acrylic Panel (60) Acrylic Panel (51) AAK2633 AAK2632
8 Card Board Spacer (60) Card Board Spacer (51P) AHB1162 AHB1172
11 Upper Carton (60P) Upper Carton (51P) AHD2962 AHD2961
12 Frame Cover Assy (60) Frame Cover Assy (51) AAP1521 AAP1520
13 Frame Cover V Assy (60) Frame Cover V Assy (51) AAP1557 AAP1560
NSP 14 Vinyl Sheet 60 Upper Vinyl Sheet XL AHG1233 AHG1095
NSP 15 Packing Sheet (60) Packing Sheet (50,45) AHG1230 AHG1120
17 Not used Caster Caution Card Not used ARM1117
NSP 20 Packing Sheet 60L Packing Sheet AHG1235 AHG1156
21 Vinyl Sheet 60 Under Vinyl Sheet MS AHG1234 AHG1258
NSP 22 Cushion F Cushion E AHA2211 AHA2081
NSP 23 Cushion D Not used AHA2077 Not used
25 Under Carton (60P) Under Carton (51P) AHD2967 AHD2966
33 Carton Runner Pad (60P) Carton Runner Pad (51P) AHA2202 AHA2201
(1) PACKING PARTS LIST
Mark No. Description Part No.
1 Card Board Case (60) See Contrast table (2)
2 Attention Card ARM1108
3 Operating Instructions (English) ARB1515
NSP 4 Literature Bag AHG1222
NSP 5 Acrylic Panel (60) See Contrast table (2)
6 Acrylic Caution Card ARH1152
NSP 7 Wrapper Bag AHG1076
8 Card Board Spacer (60) See Contrast table (2)
9 Upper Pad L AHA2067
10 Upper Pad R AHA2068
11 Upper Carton (60P) See Contrast table (2)
12 Frame Cover Assy (60) See Contrast table (2)
13 Frame Cover V Assy (60) See Contrast table (2)
NSP 14 Vinyl Sheet 60 Upper See Contrast table (2)
NSP 15 Packing Sheet (60) See Contrast table (2)
16 CONVER Attention Card ARM1139
17 Caster Caution Card See Contrast table (2)
18 Under Pad L AHA2069
19 Under Pad R AHA2070
NSP 20 Packing Sheet 60L See Contrast table (2)
Mark No. Description Part No.
21 Vinyl Sheet 60 Under See Contrast table (2)
22 Cushion F See Contrast table (2)
NSP 23 Cusion D See Contrast table (2)
NSP 24 Cusion C AHA2076
25 Under Carton (60P) See Contrast table (2)
26 Remote Contorol Unit AXD1430
(CU-SD104)
27 Battery Cover AZN7327
NSP 28 Alkaline Dry Cell Battery AEX1018
(LR6,AA)
29 Special Screw ABA1239
30 CU Packing Case AHC1019
31 Screw ABA1226
32 Screw BMZ40P100FZK
33 Carton Runner Pad (60P) See Contrast table (2)
NSP 34 Warranty Card EL ARY1026
NSP 35 Poly Bag AHG1285
(2) CONTRAST TABLE
PRO-200/KUXC/CA and PRO-100/KUXC/CA are constructed the same except for the following :

4
PRO-200, PRO-100
1.2 FRONT VIEW (1/2)
21
6
6
7
8
7
77
22
19 22
23
17
7
7
7
7
18
14
13
13
15
20
21
16
13
9
10
3
3
3
3
3
4
4
4
4
5
5
5
5
11
12

5
PRO-200, PRO-100
(1) FRONT VIEW (1/2) PARTS LIST
Mark No. Description Part No.
1 Grille (60) See Contrast table (2)
2 ELITE Badge AAM1076
NSP 3 Catcher A ANZ-241
4 Magic Tape AEC1394
5 Screw BYC35P160FZK
6 Side Cover See Contrast table (2)
7 Special Screw ABA1240
8 Side Panel Assy (60L) See Contrast table (2)
9 Side Panel Assy (60R) See Contrast table (2)
10 Door Assy AAN1413
11 Blind Plate AMM2577
12 Catcher F2M AEC1609
13 Screw APZ30P080FZK
14 MAIN SW Assy AWZ6114
NSP 15 Front Shield ANK1502
16 Sub Panel Assy AMB2556
17 Front Panel Assy AMB2614
18 Control Sheet AAK2715
19 FRONT CONTROL Assy AWZ6299
20 Coil Spring ABH1099
21 Power Knob AAD4090
22 Screw ABZ30P080FZK
23 FRONT INPUT Assy AWZ6118
(2) CONTRAST TABLE
PRO-200/KUXC/CA and PRO-100/KUXC/CA are constructed the same except for the following :
Mark No. Symbol and Description Part No. Remarks
PRO-200/KUXC/CA PRO-100/KUXC/CA PRO-200/KUXC/CA PRO-100/KUXC/CA
1 Grille (60) Grille (51) AMM2584 AMM2585
6 Side Cover Side Cover AMR2743 AMR2573
8 Side Panel Assy (60L) Side Panel Assy (51L) AMB2583 AMB2584
9 Side Panel Assy (60R) Side Panel Assy (51R) AMB2616 AMB2615

6
PRO-200, PRO-100
1.3 FRONT VIEW (2/2)
24
18
431
32
2
3
1
13
8
89
8
10 10
10
10
11
11
11 10 9
8
10
10 27 28
27
28
30
14
12
8
5
10
18
29
21
20
20
PRO-200 Only
PRO-200 Only
PRO-200 Only
PRO-200 Only
8
25
24
22
22
22
22
22
23
8
8
8
8
8
8
8
8
8
22
22
26
19
6
7
17
16
15 (PRO-100)
14 (PRO-200)
16

7
PRO-200, PRO-100
Mark No. Symbol and Description Part No. Remarks
PRO-200/KUXC/CA PRO-100/KUXC/CA PRO-200/KUXC/CA PRO-100/KUXC/CA
1 Lenticular Sheet 60 Lenticular Sheet 51 AMR3084 AMR3083
2 Almi. Frame (60) Almi. Frame (51) ANG2287 ANG2286
3 Fresnel (60PRO) Fresnel (51PRO) AMR3086 AMR3085
15 Caster Caster Not used AMR2863
NSP 17 CRT Front Holder CRT Front Holder ANG2120 ANG2121
20 Mirror Frame V Mirror Frame V ANG2007 ANG2084
21 Mirror (60A) Mirror AMR2739 AMR2852
26 Screen Frame Assy (60) Screen Frame Assy (51) AAP1515 AAP1514
29 Mirror Frame H Mirror Frame H ANG2008 ANG2083
30 Screen Holder Low (60P) Screen Holder Low (51P) AAP1590 AAP1589
32 Screen Spacer (60) Screen Spacer (51) AEC1768 AEC1767
(1) FRONT VIEW (2/2) PARTS LIST
Mark No. Description Part No.
1 Lenticular Sheet 60 See Contrast table (2)
2 Almi. Frame (60) See Contrast table (2)
3 Fresnel (60PRO) See Contrast table (2)
NSP 4 Upper Cabinet Metal ANG2000
NSP 5 Mirror Upper Stay L ANG2004
NSP 6 Mirror Upper Stay C ANG2006
NSP 7 Mirror Upper Stay R ANG2005
8 Screw BYC40P160FMC
NSP 9 Screen Side Fitting ANG1993
10 Special Screw ABA1240
11 Special Screw ABA1244
12 Tweeter APT1004
13 Cone Speaker APV1021
14 Caster AMR2547
15 Caster See Contrast table (2)
16 Special Screw ABA1126
NSP 17 CRT Front Holder See Contrast table (2)
18 M5 Screw ABA1189
NSP 19 Under Screen Metal B ANG2009
20 Mirror Frame V See Contrast table (2)
21 Mirror (60A) See Contrast table (2)
NSP 22 Upper Screen Metal B ANG2002
NSP 23 Under Screen Metal A ANG2003
24 Frame Cushion P AEC1634
NSP 25 Upper Screen Metal A ANG2001
26 Screen Frame Assy (60) See Contrast table (2)
27 Screw BYC35P160FZK
28 Washer AEC1394
29 Mirror Frame H See Contrast table (2)
30 Screen Holder Low (60P) See Contrast table (2)
31 Spacer AEC1769
32 Screen Spacer (60) See Contrast table (2)
(2) CONTRAST TABLE
PRO-200/KUXC/CA and PRO-100/KUXC/CA are constructed the same except for the following :

8
PRO-200, PRO-100
1.4 REAR VIEW
21
20
20
14
13
15
31
17
16
12
12 8
8
87
6
5
4
2
3
1
19
10
9
3
Refer to
"1.5 CHASSIS BLOCK".
Refer to
"1.6 CRT BLOCK".
18
11 20
20
21
4
3
27
26
25
22
2
22
22
29
29
28
30
37
37
33 32
34
36
22
22
2
9
9
22
23
23
22
22
22
24
25
25

9
PRO-200, PRO-100
(1) REAR VIEW PARTS LIST
Mark No. Description Part No.
NSP 1 Tray (PLS) AMR2563
2 Screw ABZ30P120FZK
3 Special Screw ABA1244
4 Screw ABA1124
NSP 5 Back Cover Panel See Contrast table (2)
6 Back Cover Cushion See Contrast table (2)
NSP 7 CRT Rear Holder ANG2119
8 Special Screw ABA1240
9 Screw ABA1149
10 Wire Harness ADX2458
11 Screw BYC40P350FZK
12 Screw PMB50P200FZK
13 Screw ACZ40P080FMC
NSP 14 Purse Lock S AEC1261
15 Purse Lock AEC1540
16 Nylon Binder AEC-093
NSP 17 CRT Stand Holder (L) ANA1516
18 8P Housing Wire (J12) ADX2257
19 Wire Holder AMR2832
20 Special Screw ABA1234
(2) CONTRAST TABLE
PRO-200/KUXC/CA and PRO-100/KUXC/CA are constructed the same except for the following :
Mark No. Symbol and Description Part No. Remarks
PRO-200/KUXC/CA PRO-100/KUXC/CA PRO-200/KUXC/CA PRO-100/KUXC/CA
NSP 5 Back Cover Panel Back Cover Panel AMM2664 AMM2663
6 Back Cover Cushion Back Cover Cushion 60 AEC1656 AEC1626
21 Screen Cushion 60 Screen Cushion 51 AEC1617 AEC1612
Mark No. Description Part No.
21 Screen Cushion 60 See Contrast table (2)
22 Screw BYC35P160FZK
23 Screw PYC40T140FZB
24 Mirror Case (51) AME2296
25 Blind Sheet AEC1622
26 Mirror Case Cushion AEC1627
27 Rear Cover AMM2893
28 Screw BMZ40P100FZK
29 Special Screw ABA1235
NSP 30 Cabinet Wire Holder AEC1263
NSP 31 CRT Stand Holder (R) ANA1517
NSP 32 IR Receiver Fixing Metal ANG1958
33 IR RECEIVER Assy AWZ6297
34 Binder AEP-215
35 • • • • •
36 Screw ABA1239
37 Screw BBZ30P080FZK

10
PRO-200, PRO-100
A
14
14
48
45
48
46
47
48
48
14 14
14
14 1117
7
5
14
13
13
13
13
9
12,14 14
14
14
23
22
22
50
22
22 19
21
21
20
20
15
8
10
18
2
1
14
15
15
16
14
4
6
3
18
49
1.5 CHASSIS BLOCK