Pioneering Technologies Safe-T-sensor Guide

Installation Instructions
and
Care & Use Manual
NOT DESIGNED AS A REPLACEMENT FOR A SMOKE DETECTOR
IMPORTANT! READ ALL INSTRUCTIONS BEFORE INSTALLATION AND KEEP THIS
MANUAL NEAR THE Safe-T-sensor™ FOR FUTURE REFERENCE.
NOT FOR COMMERCIAL USE
* Disconnecting use only.
Microwave Cooking Safety Tips from the NFPA
•
•
•
•
•
•
•
•
Note: National Fire Protection Association (NFPA) does not test, label or
approve any products.
Never leave cooking unattended.
Never leave cooking unattended.
Read the manufacturer’s instructions before using a microwave oven.
Plug the oven directly into an outlet. Never use an extension cord because
it may overload the circuit and cause a fire.
Use only microwave-safe cookware (containers or dishes).
Open microwave food slowly, away from the face. Hot steam escaping
from a container or the food itself can cause burns.
Never use aluminum foil or metal objects in a microwave oven.
If you have a fire in your microwave, turn it off immediately and keep
the door closed. Never open the door until the fire is completely out.
Have the oven checked and/or serviced before being used again.
A. Introduction:
This product is designed to help prevent microwave oven fires & false
alarms.
B. Features:
• Automatic shut-off - power to microwave interrupted (shut-off and
reset) at first sign of smoke.
• Auto-reset - power is automatically restored after cooking process
stopped.
• Easy to install & use - plug control box into outlet; plug microwave
into control box; mount magnetic Sensor to microwave just above
vent slots.
• No batteries required.
C. Power Rating/Product Type:
120VAC, 60Hz, 15Amps (maximum load)
Product Type: NM
This product is not recommended for use on:
1. Built-in microwaves unless the
exhaust vents are exposed.
2. Microwaves with a manual
dial-timer.
D. Components:
The Safe-T-sensor™ has two
components:
• “Sensor” (smoke sensor) and
• “Control box” (power supply box)
H. Troubleshooting:
Read this BEFORE you call for service.
Please review this easy to use “Troubleshooting Check List” for the
most frequently encountered situations, which may not be the result of
defective workmanship or materials.
PROBLEM POSSIBLE CAUSE/SOLUTION
Microwave
does not
operate
House fuse has blown or circuit breaker has tripped.
Check and/or replace fuse or reset circuit breaker.
Microwave cord/plug not plugged properly into the control box.
Make sure cord plug is plugged tightly into control box.
Power box not plugged properly into power outlet.
Power outage. Check house lights to be sure.
Pioneering Technology Corp. warrants that the product is free from
defects in materials and workmanship when operated and maintained
according to the instructions provided for a period of one (1) year from
date of purchase.
This warranty does not cover physical damage caused by improper
installation, misuse, neglect or accident.
This warranty is VOID if this product has been altered or modified in any
way.
For service under this warranty contact your Safe-T-sensor™ distributor
or Pioneering Technology Corp. at:
Pioneering Technology Corp. Service Dept.
220 Britannia Rd. E
Mississauga, Ontario
Canada L4Z 1S6
Tel: [phone] ext 228 or [phone] ext 228
Email: [email protected]
www.pioneeringtech.com
THERE ARE NO OTHER WARRANTIES. PIONEERING TECHNOLOGY
CORP. DISCLAIMS ALL OTHER WARRANTIES, EITHER EXPRESSED
OR IMPLIED. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS. YOU MAY HAVE OTHERS WHICH VARY FROM STATE TO
STATE.
EXCEPT AS STATED HEREIN, IN NO EVENT SHALL PIONEERING
TECHNOLOGY CORP. BE LIABLE FOR ANY DAMAGES WHATSO-
EVER WHETHER BASED ON CONTRACT, TORT, WARRANTY OR
OTHER EQUITABLE GROUNDS, INCLUDING, WITHOUT LIMITATION,
OR OTHER PECUNIARY LOSS, ARISING OUT OF THE USE OF OR
INABILITY TO USE THIS PRODUCT, EVEN IF PIONEERING
TECHNOLOGY CORP. HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL
OR INCIDENTAL DAMAGE, THE ABOVE LIMITATION MAY NOT
APPLY TO YOU.
Pioneering Technology’s entire liability and your exclusive remedy shall be at
Pioneering Technology’s option, either (a) return of the price paid for the product or (b) repair or
replacement of the product that does not meet Pioneering Technology’s Limited Warranty and
which is returned to Pioneering Technology. In no event shall Pioneering Technology’s liability
exceed the purchase price of the product.
I. Service & Warranty:

1. 2. 3.
1. 2. 3.
5. 6. 7.
4.
Sensor
Exhaust Vents
1. Plug the “Control box” into a grounded 120VAC receptacle, then plug in the
microwave power cord into the “Control box”.
2. Attach the “magnetized Sensor” to the microwave unit just above or beside
the exhaust vent slots. The Sensor has a built-in magnetic mounting.
IMPORTANT:
Microwave oven vents have been designed & slanted to expel smoke in a
specific direction. It is important that the magnetized Sensor be positioned
above or besides these exhaust vents to ensure that the expelled smoke to
pass directly over/into the Sensor.
Refer to these sample images to correctly position the Sensor on the
microwave.
In some instances the microwave vents may be located underneath or at the back of the microwave (do not confuse the air-intake holes on the back as the exhaust
vents). Again the Sensor should be positioned so that the expelled smoke will pass directly over/into the sensor.
THE Safe-T-sensor ™ must be tested periodically to ensure proper operation and optimum performance.
Ensure that the red LED on the Sensor is lit, which indicates that it is receiving power.
Clean the Sensor module at least once a year for proper operation. Ensure the slots are free from any debris. The Sensor cover is removable for cleaning.
Steps to clean Safe-T-sensor™:
1. Unplug the microwave and Safe-T-
sensor™ from the power outlet.
2. Gently remove the Sensor cover from
the Sensor case. (Fig. 1 to 3)
3. Clean any dust or debris by using a
tissue. (Fig. 4 to 5)
4. Place the Sensor cover back on the Sensor case so
it clicks back into place. (Fig. 6 to 7)
5. Plug the microwave into Safe-Tsensor™ control box
then, plug the control box back into the power outlet.
6. Position the Sensor near the microwave’s exhaust vent.
7. For Sensor that is mounted underneath the microwave base, clean the Sensor as shown in Fig.4 above.
Warning! There are no serviceable parts inside
Safe-T-sensor™.
Do not open the Safe-T-sensor™ .
Safe-T-sensor™ should not be exposed to high
humidity (80%) and ambient conditions exceeding
30 degrees C(90 degrees F) or occasionally
exposed to water.
B. Back or Underneath Installation
Please ensure that microwave is
not sitting directly on top of the
Safe-T-sensor™ to prevent
possible damage.
Refer to Section: G “Care” for instructions on
how to clean Sensor.
1. LED on sensor lights up after connecting power indicating the Sensor is
monitoring the microwave and functioning properly.
2. DO NOT press the Test/Reset button.
3. If smoke is detected by the Sensor, it will interrupt power to the microwave
and the Sensor will beep for 5 seconds indicating that the cooking process
has been stopped. The power to the microwave will be restored automatically,
but cooking will not continue until attended to by the user.
4. Do not immediately open microwave when smoke is detected. Visually
check for fire, wait 5 minutes then remove contents with heat protective
gloves.
E. Installation: F. Operation & Testing
1. Remove the Sensor cover.
2. Place the Sensor underneath the microwave base where the exhaust vent slots are located.
A. Side vent Installation:
G. Care